New analysis by the tool has shown that we have some cases where we
weren't handling the error exit condition correctly. When we ran into
the ENOMEM case we wouldn't exit the function and thus incorrect things
could happen. Rework the unwinding such that we don't need a helper
function now and free what we may have allocated.
Fixes: 18030d04d2 ("GPT: fix memory leaks identified by Coverity")
Reported-by: Coverity (CID: 275475, 275476)
Cc: Alison Chaiken <alison@she-devel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Jordy <jordy@simplyhacker.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Some PMICs (such as the DA9063) have non-contiguous register maps.
Attempting to read the non implemented registers returns an error
rather than a dummy value which causes 'pmic dump' to terminate
prematurely.
Fix this by allowing the PMIC driver to return -ENODATA for such
registers, which will then be displayed as '--' by pmic dump.
Use a single error code rather than any error code so that
we can distinguish between a hardware failure reading the PMIC
and a non implemented register known to the driver.
Signed-off-by: Martin Fuzzey <martin.fuzzey@flowbird.group>
If we didn't unbind the sata from block device, the same devices would
be added after sata remove,
This patch is to resolve this issue as below:
=> sata info
SATA#0:
(3.0 Gbps)
SATA#1:
(3.0 Gbps)
Device 0: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY30
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 1: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX30
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
=> sata stop
=> sata info
SATA#0:
(3.0 Gbps)
SATA#1:
(3.0 Gbps)
Device 0: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 1: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 2: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005PY300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Device 3: Model: INTEL SSDSA2BW300G3D Firm: 4PC10362 Ser#: BTPR247005VX300
Type: Hard Disk
Supports 48-bit addressing
Capacity: 286168.1 MB = 279.4 GB (586072368 x 512)
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'sspi' command hard-coded 1 MHz bus frequency for all transmissions.
Allow changing that at runtime by specifying '@freq' bus frequency in Hz.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch modify the loop in mtd erase command to erase one by one
the blocks in the requested area.
It solves issue on "mtd erase" command on nand with existing bad block,
the command is interrupted on the first bad block with the trace:
"Skipping bad block at 0xffffffffffffffff"
In MTD driver (nand/raw), when a bad block is present on the MTD
device, the erase_op.fail_addr is not updated and we have the initial
value MTD_FAIL_ADDR_UNKNOWN = (ULL)-1.
This case seems normal in nand_base.c:nand_erase_nand(),
we have the 2 exit cases during the loop:
1/ we have a bad block (nand_block_checkbad)
instr->state = MTD_ERASE_FAILED
loop interrupted (goto erase_exit)
2/ if block erase failed (status & NAND_STATUS_FAIL)
instr->state = MTD_ERASE_FAILED;
instr->fail_addr =
((loff_t)page << chip->page_shift);
loop interrupted (goto erase_exit)
So erase_op.fail_addr can't be used if bad blocks were present
in the erased area; we need to use mtd_erase only one block to detect
and skip these existing bad blocks (as it is done in nand_util.c).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Execute the command cls (for clear screen), when the "menu background"
keyword is present in extlinux.conf file, only if the command is supported.
This patch avoid the warning "Unknown command 'cls'"
with "menu background" in extlinux.conf when CONFIG_CMD_BMP is activated
and CONFIG_CMD_CLS not activated (default for CONFIG_DM_VIDEO).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Add support for read/write of ONIE "Tlvinfo" EEPROM data format. TLV
stands for Type-Length-Value. The data format is described here:
https://opencomputeproject.github.io/onie/design-spec/hw_requirements.html#board-eeprom-information-format
Based on U-Boot patch from the Open Compute project:
ec87e872d4/patches/u-boot/common/feature-sys-eeprom-tlv-common.patch
Keep only I2C EEPROM support. Use the generic eeprom driver. Fix
checkpatch issues.
Add support for multiple EEPROM TLV stores on the same system. This is
useful in case of SOM and carrier that both provide ID and hardware
configuration information.
Add option to enable for SPL. This allows selection of RAM configuration
based on EEPROM stored board identification.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This is not really a CONFIG since it is not intended to be set by boards.
Move it into the compiler header with other similar defines, and rename
it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function has a very generic name which does not adequately describe
its purpose. Rename it and move it to image.h, since it relates to reading
a script from an image.
Signed-off-by: Simon Glass <sjg@chromium.org>
These global variables are quite short and generic. In fact the same name
is more often used locally for struct members and function arguments.
Add a image_ prefix to make them easier to distinguish.
Signed-off-by: Simon Glass <sjg@chromium.org>
This seems pretty old now. It has not been converted to driver model and
is not used by any boards.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function belongs more in flash.h than common.h so move it.
Also remove the space before the bracket in some calls.
Signed-off-by: Simon Glass <sjg@chromium.org>
Until now, we only support aes128. This commit add the support
of aes192 and aes256.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In the code, we use the size of the key for the
size of the block. It's true when the key is 128 bits,
but it become false for key of 192 bits and 256 bits.
So to prepare the support of aes192 and 256,
we introduce a constant for the iaes block size.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When no partition table is found, users should be warned so.
Warning that no device is available in this case could be misleading,
especially as it is the same error when no device is selected.
Signed-off-by: Alexandre Besnard <alexandre.besnard@softathome.com>
Trying to extend 'adtimg' functionality [1], we've been severely hit
by a major limitation in the command's usage scheme. Specifically, the
command's user interface appears to be too centric to getting the
DTB/DTBO entry [3] based on the index of the desired DT in the image,
which makes it really difficult retrieving the DT entry based on
alternative criteria (e.g. filtering by id/rev fields), the
latter being demanded by real life customer use-cases [1].
This went to the point of receiving below feedback from Sam [2]:
-- snip --
As for 'dtimg' command: after giving it some thought, I think not much
people using it yet. So in this particular case I don't have some
strong preference, and if you think the 'dtimg' interface is ugly, and
it overcomes "don't break interfaces" rule, maybe now is a good time
to rework it (before it gets widely used).
-- snip --
Given the above, rework the usage pattern from [4] to [5], in order to
allow an intuitive enablement of "by id|rev" DT search [6].
[1] https://patchwork.ozlabs.org/cover/1202575/
("cmd: dtimg: Enhance with --id and --rev options (take #1)")
[2] https://patchwork.ozlabs.org/patch/1182207/#2317020
[3] https://source.android.com/devices/architecture/dto/partitions
[4] Old usage
adtimg dump <addr> - Print image contents
adtimg start <addr> <index> <varname> - Get DT address by index
adtimg size <addr> <index> <varname> - Get DT size by index
[5] New usage
adtimg addr <addr> - Set image location to <addr>
adtimg dump - Print out image contents
adtimg get dt --index=<i> [avar [svar]] - Get DT address and size by index
[6] Soon-to-be-provided "by id|rev" add-on functionality
adtimg get dt --id=<id> --rev=<rev> [avar [svar [ivar]]]
- Get DT address/size/index by id|rev fields
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
With 'dtimg.c' renamed to 'adtimg.c', now ensure the naming
consistency in the internal implementation of 'adtimg.c'.
No functional change intended.
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename the existing 'dtimg' command to 'adtimg', in order to:
- Suggest the Android origins and scope
- Be consistent with the upcoming 'abootimg' command (naming
suggested by Simon [*])
The change in _not_ backward compatible, but its benefits outweigh its
downsides, given that we don't expect active users of 'dtimg' today.
Perform the rename in several steps:
1. Rename *.c file and Kconfig symbol. This should allow
'git log --follow' to properly track the history of 'adtimg.c'
2. 's/dtimg/adtimg/g' in the internal namespace of 'adtimg.c'
ELF comparison [**] before and after shows no functional change.
[*] https://patchwork.ozlabs.org/patch/1182212/#2291600
[**] diff -u <(objdump -d cmd/dtimg.o) <(objdump -d cmd/adtimg.o)
Cc: Tom Rini <trini@konsulko.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Simon Glass<sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
If the numbers do not happen to contain any digits from [a-f], it's
not clear that they are base 16.
Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
-----BEGIN PGP SIGNATURE-----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=SjPV
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc1
This pull request provides:
* support for FIT images for UEFI binaries
* drivers for hardware random number generators
* an implementation of the EFI_RNG_PROTOCOL
* a sub-command for efidebug to display configuration tables
Per Enea OSE documentation, it supports some classes of ARM, PowerPC and
X86. Limit the option to those platforms.
Signed-off-by: Tom Rini <trini@konsulko.com>
For the RNG uclass we currently only have a test working on the sandbox.
Provide a command to test the hardware random number generator on
non-sandbox systems.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add support for booting EFI binaries contained in FIT images.
A typical usage scenario is chain-loading GRUB2 in a verified
boot environment.
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When we hit a matching GUID we can directly return the text. There is no
need for a check after the loop.
efi_guid_t is defined as 8 byte aligned but GUIDs in packed structures do
not follow this alignment. Do not require the argument of get_guid_text()
to be correctly aligned.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When be launch a binary via bootefi the bootargs environment variable is
used to set the load options in the loaded image protocol.
Free memory allocated for load options when the UEFI binary exits.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Use a pointer to addressable memory instead of a "physical" address in the
virtual address space of the sandbox to efi_install_fdt().
Export the efi_install_fdt() function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If the bootefi command is called without passing the address of a device
tree, the internal device tree is used. For devices with a hardware device
tree it is preferable to used the hardware device tree in this case.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
As part of moving the parsing of command line arguments to do_bootefi()
call efi_install_fdt() with the address of the device tree instead of a
string.
If the address is EFI_FDT_USE_INTERNAL (= 0), the internal device tree
is used.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
if MULTI_DTB_FIT is enabled it is helpful to display
the value of gd->multi_dtb_fit in bdinfo.
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When the `dfu` command is called from the U-Boot environment,
it now accepts an optional parameter that specifies a timeout (in seconds).
If a DFU connection is not made within that time the `dfu` command exits
(as it would if Ctrl+C was pressed). If the timeout is left empty or being
zero the `dfu` command behaves as it does now.
This is useful for allowing U-Boot to check to see if anything wants to
upload new firmware before continuing to boot.
The patch is based on the commit
5e966ccc3c
by Sebastien Colleur, which has been heavily reworked due to U-Boot changes
in the past.
Signed-off-by: Brad Campbell <bradjc5@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
In the future we may utilize optional argument in 'dfu' command line.
As a preparation for this, refactor do_dfu().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
The current 'fsp' command only works with FSP1. Update it to handle FSP2
as well. Convert everything to hex which is what U-Boot uses.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
On NixOS, cross compiled kernels have long suffixes that cause them to
exceed the current maximum path length. The PXE/TFTP max path length is
used for extlinux.conf support as well, which is where this problem
usually manifest's itself.
Signed-off-by: Ben Wolsieffer <benwolsieffer@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
* Add Kconfig help describing the purpose of each command.
* Add CONFIG_CMD_MDIO so it could be selected individually, as
it doesn't depend on the mii command.
* Add Kconfig imply to mii to automatically select the mdio
command.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Part of the env cleanup moved this out of the environment code and into
the net code. However, this helper is sometimes needed even when the net
stack isn't included.
Move the helper to lib/net_utils.c like it's similarly-purposed
string_to_ip(). Also rename the moved function to similar naming.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reported-by: Ondrej Jirman <megous@megous.com>
In the next commit, rtc_mktime(), for compatibility with linux, will be
implemented using rtc_mktime(), which is no longer drivers/rtc specific.
So move this file under lib/.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Extract all sysboot command related code from pxe.c to new sysboot.c
Update Kconfig to insure that DISTRO_DEFAULT select new CMD_SYSBOOT
command.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
As sysboot and pxe commands are sharing piece of code, migrate this
common code into a new file pxe_utils.c to prepare sysboot command
code extraction from pxe.c
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
The command cp fails on sandbox because the address is used
directly. To fix this issue, we call the function map_sysmem
to translate the address.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The command iminfo fails on sandbox because the address
is used directly. To fix this issue, we call the function
map_sysmem to translate the address.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Defconfigs have been fixed, now we can add proper dependencies in
Kconfig. SPI FLASH is still not dependent on MTD (deeper rework needed).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
The 'sf' command is not supposed to rely on the MTD stack, but both
'sf' and 'nand' commands use helpers located in mtd_uboot.c. Despite
their location, these functions do not depend at all on the MTD
stack.
This file (drivers/mtd/mtd_uboot.c) is only compiled if CONFIG_MTD is
selected, which is inconsistent with the current situation. Solve this
by moving these three functions (which are only used by the above two
commands) out of mtd_uboot.c and put them in a C file only compiled
with cmd/sf.c and cmd/nand.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Don't export get_part function now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Like in Linux, just use CONFIG_MTD to compile the MTD stack.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Add more clarity by changing the Kconfig entry name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
[trini: Re-run migration, update a few more cases]
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
A type error in the implementation of the efidebug command is fixed.
-----BEGIN PGP SIGNATURE-----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=spg0
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc5' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc5
A type error in the implementation of the efidebug command is fixed.
I detected the following error in sandbox with Clang on Travis CI:
+cmd/efidebug.c:703:15: error: result of comparison of constant
9223372036854775822 with expression of type 'int' is always false
[-Werror,-Wtautological-constant-out-of-range-compare]
+ else if (ret == EFI_NOT_FOUND)
+ ~~~ ^ ~~~~~~~~~~~~~
Simply changing a type of 'ret' to efi_status_t will fix this error.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
pxe command parses the init ramfs address(through initrd lable in
pxe config file), but is not passing it to bootm command as argument
as bootm_argc count is not increased.
Signed-off-by: Abhishek Shah <abhishek.shah@broadcom.com>
Signed-off-by: Vladimir Olovyannikov <vladimir.olovyannikov@broadcom.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When we do not have CONFIG_BLK (or SPL/TPL) enabled there are very few
cases where we need the blk_legacy code linked in. To catch these, build
when we have CONFIG_HAVE_BLOCK_DEVICE set. In addition, we only need
cmd/blk_common.o to be linked in when we have CONFIG_HAVE_BLOCK_DEVICE
set, so make use of that directly.
Signed-off-by: Tom Rini <trini@konsulko.com>
These functions do not use driver model but are still used. Move them to a
new eeprom.h header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
This function is not defined by any boards so the feature is not used.
Drop it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Move these two functions into the irq_funcs.h header file. Also move
interrupt_handler_t as this is used by the irq_install_handler() function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions are CPU-related and do not use driver model. Move them to
cpu_func.h
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.
Move them over.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present this function sits in its own file but it does not really
justify it. There are similar string functions in vsprintf.h, so move it
there. Also add the missing function comment.
Use the vsprintf.h include file explicitly where needed.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These don't need to be in common.h so move them out into a new header.
Also add some missing comments.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Drop inclusion of crc.h in common.h and use the correct header directly
instead.
With this we can drop the conflicting definition in fw_env.h and rely on
the crc.h header, which is already included.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some of these have a space before the bracket. Drop it to fix the style.
Add some missing function comments while here.
Note that u32 and u8 cannot be used here since crc.h is included on the
host side.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
These should be moved to driver model, but in the meantime, move them
out of the common header to help reduce its size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
On the sandbox the UEFI binaries must match the host architectures.
Adjust the Makefiles. Provide the PE/COFF header and relocation files.
Allow building helloworld.efi on the sandbox.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Due to the commit 4b0bcfa7c4 ("Kconfig: Migrate CONFIG_BOOTM_* options")
BOOTEFI and BOOTEFI_HELLO_COMPILE (and other BOOTEFI configs) are
displayed in a long distance. This will make it difficult for us to
understand that those configurations are closely related.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
That option is currently not used by any defconfig and could not be set
anymore since it became mandatory to used Kconfig when introducing new
options with U-Boot v2016.11 or commit eed921d923 ("Kconfig: Add a
whitelist of ad-hoc CONFIG options") and commit 371244cb19 ("Makefile:
Give a build error if ad-hoc CONFIG options are added").
It was also not considered when fixing build warnings in
commit 39ac34473f ("cmd_mtdparts: use 64 bits for flash size,
partition size & offset") and could probably not be compiled anyway
after commit dfe64e2c89 ("mtd: resync with Linux-3.7.1"), which
renamed some members of struct mtd_info … so it was probably broken
since then, which was U-Boot v2013.07-rc1.
However it still seems to work, see example output below:
U-Boot 2019.10-00035-g06a9b259ca-dirty (Oct 30 2019 - 14:03:44 +0100)
CPU: SAMA5D27 1G bits DDR2 SDRAM
Crystal frequency: 24 MHz
CPU clock : 492 MHz
Master clock : 164 MHz
Model: ***
DRAM: 128 MiB
NAND: 256 MiB
Loading Environment from NAND... OK
In: serial@f8020000
Out: serial@f8020000
Err: serial@f8020000
Net: eth0: ethernet@f8008000
Hit keys 'tt' to stop autoboot (3 seconds).
U-Boot> mtdparts
device nand0 <atmel_nand>, # parts = 8
#: name size net size offset mask_flags
0: bootstrap 0x00040000 0x00040000 0x00000000 1
1: uboot 0x000c0000 0x000c0000 0x00040000 1
2: env1 0x00040000 0x00040000 0x00100000 0
3: env2 0x00040000 0x00040000 0x00140000 0
4: fpga_led 0x00040000 0x00040000 0x00180000 1
5: reserved 0x00040000 0x00040000 0x001c0000 1
6: rootfs_rec 0x03200000 0x03200000 0x00200000 1
7: filesystem 0x0cc00000 0x0cb80000 (!) 0x03400000 0
active partition: nand0,0 - (bootstrap) 0x00040000 @ 0x00000000
defaults:
mtdids : nand0=atmel_nand
mtdparts: mtdparts=atmel_nand:256k(bootstrap)ro,768k(uboot)ro,256k(env1),256k(env2),256k(fpga_led)ro,256k(reserved)ro,50M(rootfs_rec)ro,-(filesystem)
Signed-off-by: Alexander Dahl <ada@thorsis.com>
This declaration is not used anywhere in the whole tree. There is a
function 'mtd_id_parse()' which was renamed from 'id_parse()' in
commit 68d7d65100 ("Separate mtdparts command from jffs2"), but that
function is not used (anymore?) in cmd nand and build is fine without
that declaration, so it's probably just safe to remove.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
-----BEGIN PGP SIGNATURE-----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=f0m8
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc2
Provide a better user interface for setting UEFI variables.
Bug fixes:
- ext4 file system not discovered on UEFI block device
- 'make tests' build error on 32bit systems
Add optional parameter to 'avb verify' sub-command, so that user is able
to specify which slot to use, in case when user's partitions are
slotted. If that parameter is omitted, the behavior of 'avb verify' will
be the same as before, so user API is content.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Acked-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Add support of DFU for several interface/device
with one command.
The format for "dfu_alt_info" in this case is :
- <interface> <dev>'='alternate list (';' separated)
- each interface is separated by '&'
The previous behavior is always supported.
One example for NOR (bootloaders) + NAND (rootfs in UBI):
U-Boot> env set dfu_alt_info \
"sf 0:0:10000000:0=spl part 0 1;u-boot part 0 2; \
u-boot-env part 0 3&nand 0=UBI partubi 0,3"
U-Boot> dfu 0 list
DFU alt settings list:
dev: SF alt: 0 name: spl layout: RAW_ADDR
dev: SF alt: 1 name: ssbl layout: RAW_ADDR
dev: SF alt: 2 name: u-boot-env layout: RAW_ADDR
dev: NAND alt: 3 name: UBI layout: RAW_ADDR
U-Boot> dfu 0
$> dfu-util -l
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=3, name="UBI", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=2, name="u-boot-env", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=1, name="u-boot", serial="002700333338511934383330"
Found DFU: [0483:5720] ver=9999, devnum=96, cfg=1,\
intf=0, alt=0, name="spl", serial="002700333338511934383330"
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
'THOR' download command requires DFU infrastructure to properly flash
board images. It can be used without enabling DFU command, so add such
dependency to Kconfig.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
With this patch, when setting UEFI variable with "env set -e" command,
we will be able to
- specify vendor guid with "-guid guid",
- specify variable attributes, BOOTSERVICE_ACCESS, RUNTIME_ACCESS,
respectively with "-bs" and "-rt",
- append a value instead of overwriting with "-a",
- use memory as variable's value instead of explicit values given
at the command line with "-i address,size"
If guid is not explicitly given, default value will be used.
Meanwhile, "env print -e," will be modified so that it will NOT dump
a variable's value if '-n' is specified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
If DM_SPI_FLASH enabled that means it is using sf command
for flash interface to access.
SPI_FLASH can be used via sf command and board/driver
functions to call spi flash ops, so mark it default only
for DM_SPI_FLASH.
This would prevent explicit adding of CONFIG_CMD_SF when
DM_SPI_FLASH being enabled.
Cc: Tom Rini <trini@konsulko.com>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Support for commands to initialize and configure UFS devices.
TODO: Add Support for commands to resize and reconfigure LUNs
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
ubi enhancements for 2020.01
- provide a way for skipping crc checks ported from linux, and add an
U-Boot command to set this flag on already installed systems.
- fix redundand environment management
U-Boot now supports the "skip_check" flag to optionally skip the CRC
check at open time. Currently its only possible to set this bit upon
UBI volume creation. But it might be very useful to also set this bit
on already installed systems (e.g. field upgrade) to make also use of
the boot-time decrease on those systems.
This patch now adds a new "ubi" command "ubi skipcheck" to set or clear
this bit in the UBI volume header:
=> ubi skipcheck rootfs0 on
Setting skip_check on volume rootfs0
BTW: This saves approx. 10 seconds Linux bootup time on a MT7688 based
target with 128MiB of SPI NAND.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@collabora.com>
Cc: Heiko Schocher <hs@denx.de>
Cc: Andreas Dannenberg <dannenberg@ti.com>
Some users of static UBI volumes implement their own integrity check,
thus making the volume CRC check done at open time useless. For
instance, this is the case when one use the ubiblock + dm-verity +
squashfs combination, where dm-verity already checks integrity of the
block device but this time at the block granularity instead of verifying
the whole volume.
Skipping this test drastically improves the boot-time.
Adapted to U-Boot by Stefan Roese.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
Cc: Quentin Schulz <quentin.schulz@bootlin.com>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
The aes command used to segfault when accessing memory in sandbox.
The pointer accesses should be mapped.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This patch uses auto instead of decimal in simple_strtoul().
Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
If the ECC is enabled over the entire memory region, we need to ensure
the printf/put calls do not modify the stack after ECC is disabled.
Moved the printf/put statements after ECC is enabled.
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
ecc_address_range registers contains the start address and end address
of the DDR address space. But the ddr cmd driver is assuming the register
contains the start address and size of the DDR address space. Because
of this some valid ecc addresses are errored out as invalid address.
Fix this calculation.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
- Rename existing FSP code to fsp1
- Add fsp2 directory in preparation to support FSP 2.0
- Various x86 platform codes update
- Various bug fixes and updates in dm core, sandbox and spl
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
-----BEGIN PGP SIGNATURE-----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=nzgb
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-01-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-01-rc1
The major corrections in this pull request are:
Fixes for the SetVariable() boot service.
Device path node for NVMe drives.
Disable CONFIG_CMD_NVEDIT by default.
All boards are using the same prompt that's why add it as default value to
Kconfig to simplify defconfigs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Luca Ceresoli <luca@lucaceresoli.net>
All boards are using the same prompt that's why add it as default value to
Kconfig to simplify defconfigs.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
At present the 'iod' command differs from 'md' in that it only shows a
single value. It is useful to see a dump of multiple values, particularly
when x86 peripherals contain register sets accessible via I/O ports.
Enhance the command to match md.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct multi-line comment format style]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Given these exported function an fsp_ prefix since they are declared in an
fsp.h header.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Since there is now a new version of the FSP and it is incompatible with
the existing version, move the code into an fsp1 directory. This will
allow us to put FSP v2 code into an fsp2 directory.
Add a Kconfig which defines which version is in use.
Some of the code in this new fsp1/ directory is generic across both FSPv1
and FSPv2. Future patches will address this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
With the patch below applied, host_block_dev structure was switched
to be placed in platdata rather than priv. The command "host info"
must be aligned with this change. Otherwise, we will see "Segmentation
Fault."
Fixes: 8f994c860d ("sandbox: blk: Switch to use platdata_auto_alloc_size for the driver data")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The growth of the UEFI sub-system leads to build failures for systems with
strict limits on the U-Boot image size.
CMD_NVEDIT_EFI supports displaying and editing of UEFI variables. The
setting is not needed for booting. Disabling it by default reduces the
size of the U-Boot image by 2 KiB.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A wrong function name is referred to in a comment of do_env_set_efi().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
At this point we are using part number sub-command to retrieve UUID
of the partition using it's name.
e.g.:
part number mmc $mmcdev system_a system_a_index
part uuid mmc $mmcdev:${system_a_index} system_a_uuid
Since 'part uuid' sub-command expects partition index in hex format and
'part number' returns decimal value, 'part uuid' command will provide
wrong UUID or fail.
Fixes: be683756f6 ("cmd: part: Add 'number' sub-command")
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Reported-by: Pontus Fuchs <pontus.fuchs@se.bosch.com>
Signed-off-by: Roman Stratiienko <roman.stratiienko@globallogic.com>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Add support for capturing ethernet packets and storing
them in memory in PCAP(2.4) format, later to be analyzed by
any PCAP viewer software (IE. Wireshark)
This feature greatly assist debugging network issues such
as detecting dropped packets, packet corruption etc.
Signed-off-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Tested-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The command "pci bar" and "pci region" display the address and size in
16 characters including "0x", so the command can only display
14 hexadecimal digits if the number of digits in the address and size is
less than 14.
ID Base Size Width Type
----------------------------------------------------------
0 0x00000020000000 0x00000000100000 64 MEM Prefetchable
1 0xffff000080000000 0x00000000100000 64 MEM Prefetchable
The 64-bit address and size should be displayed in 18(= 16+2) digits,
so this patch adjusts them.
Cc: Yehuda Yitschak <yehuday@marvell.com>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The assigned value NULL is overwritten before being used. Remove the
assignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move the result variable into the struct also, so that it can be used when
BSS is not available. Add a function to read it.
Note that all functions sill use the BSS version of the data.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
This file contains lots of internal details about the environment. Most
code can include env.h instead, calling the functions there as needed.
Rename this file and add a comment at the top to indicate its internal
nature.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
[trini: Fixup apalis-tk1.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Avoid using a typedef here which is unnecessary. Add an 'env_' prefix to
both the enum and its members to make it clear that these are related to
the environment.
Add an ENV prefix to these two flags so that it is clear what they relate
to. Also move them to env.h since they are part of the public API. Use an
enum rather than a #define to tie them together.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an ENV prefix to these two flags so that it is clear what they relate
to. Also move them to env.h since they are part of the public API. Use an
enum rather than a #define to tie them together.
Signed-off-by: Simon Glass <sjg@chromium.org>
U-Boot is not supposed to use typedef for structs anymore. Also this name
is the same as the ENTRY() macro used in assembler files, and 'entry'
itself is widely used in U-Boot (>8k matches).
Drop the typedef and rename the struct to env_entry to reduce confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move these functions to the new header file and rename set_default_env()
to env_set_default() so that it has a consistent env_ prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Move this function to the new header file and rename it so it has an env_
prefix.
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
This function fits better with the network subsystem, so move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Suggested-by: Joe Hershberger <joe.hershberger@ni.com>
Move env_set_hex() over to the new header file along with env_set_addr()
which uses it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move envmatch() over to the new header file. Also rename it to env_match()
to better line up with other functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Move this function over to the new header file. Also rename it to have an
env_ prefix like the other functions.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As part of the effort to remove things from common.h, create a new header
for the gzip functions. Move the function declarations to it and add
missing documentation.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
FSP (CONFIG_HAVE_FSP) and Slim Bootloader (CONFIG_SYS_SLIMBOOTLOADER)
consume HOB (CONFIG_USE_HOB) data from the each HOB list pointer.
Add a common HOB library in lib/hob.c and include/asm/hob.h.
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Use existing EFI_GUID and efi_guid_t instead of struct efi_guid.
This is pre-work before making a common HOB library.
- Change 'struct efi_guid' to efi_guit_t
- Remove 'struct efi_guid'
- Define GUIDs with EFI_GUID() macro
- Use guidcmp() instead of compare_guid()
- Remove compare_guid()
Signed-off-by: Aiden Park <aiden.park@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested on MinnowMax
Tested-by: Bin Meng <bmeng.cn@gmail.com>
Registration of USB download gadget might fail for various reasons, so
add a check for g_dnl_register() funtion return value. Without this fix,
thor_init() will try to access the registered gadget structures resulting
in NULL pointer dereference issue.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
When building U-Boot with AVB enabled, compiler shows next warnings:
cmd/avb.c: In function 'do_avb_read_pvalue':
cmd/avb.c:371:18: warning: format '%ld' expects argument of type
'long int', but argument 2 has type 'size_t'
{aka 'unsigned int'} [-Wformat=]
printf("Read %ld bytes, value = %s\n", bytes_read,
~~^ ~~~~~~~~~~
%d
cmd/avb.c: In function 'do_avb_write_pvalue':
cmd/avb.c:404:19: warning: format '%ld' expects argument of type
'long int', but argument 2 has type '__kernel_size_t'
{aka 'unsigned int'} [-Wformat=]
printf("Wrote %ld bytes\n", strlen(value) + 1);
~~^ ~~~~~~~~~~~~~~~~~
%d
Fix those by using "%zu" specified.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
With this pull request a workaround for GRUB on 32bit ARM is re-enabled
and made customizable. Without the patch booting on ARM 32bit with GRUB
prior to version 2.04 or with a cache which is not managed via CP15
fails.
Further work will be needed to achieve a UEFI compliant cache handling.
According to the UEFI spec all caches except those that cannot be
managed via CP15 should be enabled.
An implementation of the ConvertPointer() runtime service is provided.
efi_crt0 is always rebuild to avoid having to call 'make mrproper' when
switching architectures.
-----BEGIN PGP SIGNATURE-----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=jfh5
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc2
With this pull request a workaround for GRUB on 32bit ARM is re-enabled
and made customizable. Without the patch booting on ARM 32bit with GRUB
prior to version 2.04 or with a cache which is not managed via CP15
fails.
Further work will be needed to achieve a UEFI compliant cache handling.
According to the UEFI spec all caches except those that cannot be
managed via CP15 should be enabled.
An implementation of the ConvertPointer() runtime service is provided.
efi_crt0 is always rebuild to avoid having to call 'make mrproper' when
switching architectures.
Since this is part of the autoboot functionality, it makes sense to name
it with an AUTOBOOT prefix. No mainline boards use it so this should be
safe, and downstream boards will need to adjust.
Since this option is just an integer value, it really needs another option
to control whether the feature is enabled or not. Add a new
CONFIG_USE_AUTOBOOT_MENUKEY for that. This fits better with how things are
done with Kconfig, avoiding the need to use a specific value to disable
the feature.
Signed-off-by: Simon Glass <sjg@chromium.org>
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
-----BEGIN PGP SIGNATURE-----
iGwEABECACwWIQSC4hxrSoIUVfFO0kRM6ATMmsalXAUCXUCEtQ4cYWd1c3RAZGVu
eC5kZQAKCRBM6ATMmsalXLYhAJ4gSCCx54ubBmbsZ1cueGk59E/SkwCdFl7nfLqz
Vy/HbBVAUkzD4JVOR0U=
=7rSM
-----END PGP SIGNATURE-----
Merge tag 'video-for-2019.10-rc1' of https://gitlab.denx.de/u-boot/custodians/u-boot-video
- fix EDID mode filtering
- extend mxc_ipuv3_fb to enable backlight/display
- include fb_base in global_data for DM_VIDEO
- show frame buffer address via board info
as used to be with legacy VIDEO support
make htmldocs produces a warning:
./cmd/efidebug.c:733: WARNING: Unexpected indentation.
Correct the indentation.
Remove 'See above for details of sub-commands.' which is not helpful in the
Sphinx generated documentation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A couple minor tweaks to printed strings in cmd/fpga.c.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Linker generated array entry is not needed when the command line is
disabled. Remove this code in that case.
This is required as the commit 80a48dd47e
breaks the linking stage when CONFIG_CMDLINE=n:
..
LDS u-boot.lds
LD u-boot
u-boot contains unexpected relocations: R_ARM_NONE
R_ARM_RELATIVE
make: *** [Makefile:1775: checkarmreloc] Error 1
Signed-off-by: Andrej Rosano <andrej.rosano@f-secure.com>
'rproc list' is currently allowed only after probing all the
available remoteproc devices. Given that 'rproc init' is updated
to probe and initialize devices individually, allow the 'rproc list'
command to print all probed devices at any point.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
'rproc init' does the probe and initialization of all the available
remoteproc devices in the system. This doesn't allow the flexibility
to initialize the remote cores needed as per use case. In order
to provide flexibility, update 'rproc init' command to accept one
more parameter with rproc id which when passed initializes only
that specific core. If no id is passed, command will initializes
all the cores which is compatible with the existing behaviour.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
For A/B system update support the Android boot process requires to send
'androidboot.slot_suffix' parameter as a command line argument. This
patch implementes 'ab_select' command which allows us to obtain current
slot by processing the A/B metadata.
The patch was extracted from commit [1] with one modification: the
separator for specifying the name of metadata partition was changed
from ';' to '#', because ';' is used for commands separation.
[1] https://android-review.googlesource.com/c/platform/external/u-boot/+/729880/2
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
These have been reported by Simon in [1] and fixed in [2].
However, since [1] has already been pushed to u-boot/master, the
improvements incorporated in [2] are now extracted and resubmitted.
The changes are in the area of coding style and best practices:
* s/field/fieldp/, s/size/sizep/, to convey that the variables return
an output to the caller
* s/err_1/err_read_fail/, s/err_2/err_too_small/, to be more descriptive
* Made sure 'static int do_bcb_load' appears on the same line
* Placed a `/*` on top of multi-line comment
[1] https://patchwork.ozlabs.org/patch/1104244/#2200259
[2] https://patchwork.ozlabs.org/cover/1128661/
("[v4,0/4] Add 'bcb' command to read/modify/write Android BCB")
Fixes: db7b7a05b2 ("cmd: Add 'bcb' command to read/modify/write BCB fields")
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Quote from https://patchwork.ozlabs.org/patch/1104244/#2210814:
----------8<-----------
strncmp() is chosen for the sake of paranoid/defensive programming.
Indeed, strncmp() is not really needed when comparing a variable
with a string literal. We expect strcmp() to behave safely even if the
string variable is not NUL-terminated.
In the same scenario, Linux v5.2-rc7 uses both strcmp() and strncmp(),
but the frequency of strcmp() is higher:
$ git --version
git version 2.22.0
$ (Linux 5.2-rc7) git grep -En 'strncmp\([^"]*"[[:alnum:]]+"' | wc -l
1066
$ (Linux 5.2-rc7) git grep -En 'strcmp\([^"]*"[[:alnum:]]+"' | wc -l
1968
A quick "strcmp vs strncmp" object size test shows that strcmp()
generates smaller memory footprint (gcc-8, x86_64):
$ (U-Boot) size cmd/bcb-strncmp.o cmd/bcb-strcmp.o
text data bss dec hex filename
3373 400 2048 5821 16bd cmd/bcb-strncmp.o
3314 400 2048 5762 1682 cmd/bcb-strcmp.o
So, overall, I agree to use strcmp() whenever variables are compared
with string literals.
----------8<-----------
Fixes: db7b7a05b2 ("cmd: Add 'bcb' command to read/modify/write BCB fields")
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Fix warning V1037 reported by PVS-Studio Static Analyzer:
Two or more case-branches perform the same actions. Check lines: 49, 53
Fixes: db7b7a05b2 ("cmd: Add 'bcb' command to read/modify/write BCB fields")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Commit 9bdf0e8fef ("doc: relocate/rename Android README and add BCB
overview") left some obsolete references of Android documents/paths.
This has been pointed out by Sam (thanks!) in:
https://patchwork.ozlabs.org/patch/1104245/#2208134
Fixes: 9bdf0e8fef ("doc: relocate/rename Android README and add BCB overview")
Reported-by: Sam Protsenko <semen.protsenko@linaro.org>
Suggested-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
This sub-command serves for getting the partition index from
partition name. Also it can be used to test the existence of specified
partition.
Use case:
For example, in most CI environments this U-Boot command for automatic
testing of Linux rootfs is used:
=> setenv bootpart 1:f
where 0xf is "userdata" partition. But the number of "userdata"
partition can be changed any time, when partition table is changed.
So it would be nice to get rid of that 0xf magic number and use
partition name instead, like this:
=> part number mmc 1 userdata part_num
=> setenv bootpart 1:${part_num}
Signed-off-by: Ruslan Trofymenko <ruslan.trofymenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
Reviewed-by: Alistair Strachan <astrachan@google.com>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
-----BEGIN PGP SIGNATURE-----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=aj4j
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-10-rc1-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.10-rc1 (2)
* Implement the EVT_SIGNAL_VIRTUAL_ADDRESS_CHANGE event.
* Address errors of type -Werror=address-of-packed-member when building
with GCC9.1
* Fix an error when adding memory add addres 0x00000000.
* Rework some code comments for Sphinx compliance.
This commit just corrects spelling of 'accessed' word in the EEPROM
comment.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This option will provide the offset in the parallel NOR flash memory to,
which the falcon boot data is stored.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This commit makes the CMD_SPL_NAND_OFS only visible when we use NAND
memory.
Before this change it was present when only CMD_SPL was enabled (and
would stay when board with other falcon boot medium is used).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Calling 'mdio read ...' currently leads to a data abort when no mdio
bus is found.
To fix this, check if 'bus' is a valid pointer before accessing it.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
this patch adds basic changes for adding a erase-subcommand to env
with this command the environment stored on non-volatile storage written
by saveenv can be cleared.
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
squashed fixes
- start message with "Erasing"
- mark erase-function as optional
- env: separate eraseenv from saveenv
Suggested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
We currently have some inconsistent use of efi_add_memory_map()
throughout the code. In particular the return value of efi_add_memory_map()
is not interpreted the same way by various users in the codebase.
This patch does the following:
- Changes efi_add_memory_map() to return efi_status_t.
- Adds a method description to efi_add_memory_map().
- Changes efi_add_memory_map() to return EFI_SUCCESS
- Returns non-zero for error in efi_add_memory_map()
- Updates efi_allocate_pages() to new efi_add_memory_map()
- Updates efi_free_pages() to new efi_add_memory_map()
- Updates efi_carve_out_dt_rsv() to new efi_add_memory_map()
- Updates efi_add_runtime_mmio() to new efi_add_memory_map()
Fixes: 5d00995c36 ("efi_loader: Implement memory allocation and map")
Fixes: 74c16acce3 ("efi_loader: Don't allocate from memory holes")
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Alexander Graf <agraf@csgraf.de>
Signed-off-by: Bryan O'Donoghue <pure.logic@nexus-software.ie>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Adds UCLASS_MDIO DM class supporting MDIO buses that are probed as
stand-alone devices. Useful in particular for systems that support
DM_ETH and have a stand-alone MDIO hardware block shared by multiple
Ethernet interfaces.
Signed-off-by: Alex Marginean <alexm.osslist@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
These are standard across gigabit phys. These mostly extend the
auto-negotiation information with gigabit fields.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Share the code that prints out a register field with the function that
prints out the "special" fields.
There were two arrays the register dump list, one with reg number and
name, another with a pointer to the field table and the table size.
These two arrays had have each entry match what register is referred to.
Combine them into just one table. Now they can't not match and there is
just one table.
Add some missing consts to pointers to string literals.
The dump code was ignoring the regno field in the description table and
assuming register 0 was at index 0, etc. Have it use the field.
Change reg > max+1 into reg >= max, which doesn't fail if max+1 could
overflow, besides just making more sense.
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
- mmc spi driver model support
- drop mmc_spi command
- enhanced Strobe mmc HS400 support
- minor mmc bug/fixes and optimization
- omap hsmmc and mvbeu update
- sdhci card detect support
The mmc_spi command was added to manually setup MMC over SPI bus
using command. This was required by the legacy non-DM MMC_SPI driver.
With DM based MMC_SPI driver in-place, we can now use all general
storge commands and mmc command for MMC over SPI bus hence we remove
the mmc_spi command all it's references.
Suggested-by: Bin Meng <bmeng.cn@gmail.com>
Signed-off-by: Anup Patel <anup.patel@wdc.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Add sub-command 'env info' to display environment information:
- env_valid : is environment valid
- env_ready : is environment imported into hash table
- env_use_default : is default environment using
This command can be optionally used for evaluation in scripts:
[-d] : evaluate whether default environment is used
[-p] : evaluate whether environment can be persisted
The result of multiple evaluations will be combined with AND.
Signed-off-by: Leo Ruan <tingquan.ruan@cn.bosch.com>
Signed-off-by: Mark Jonas <mark.jonas@de.bosch.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: Do not enable by default]
Signed-off-by: Tom Rini <trini@konsulko.com>
This patch solves the following warnings:
cmd/pinmux.c: In function 'do_dev':
cmd/pinmux.c:26:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret) {
^
cmd/pinmux.c:30:2: note: here
case 1:
^~~~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl0nbDoRHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZcBQgAn+ojgq/hD89bihuhz2oEe6rhzHB9OkcC
sHrVL8Jbmby/BuzISGe4oeeM5yVygBVtUiN/72JiiAHLmykqc4CpRjNvgOOAgKCy
Ml8UyiBNNVNfrD6f9PxAKvPZf6S0gfLnomGOQ/psdEojpY5AvQxQ36D+QFZ0AMP5
67/xjSfN9bNPw8UbgE/VhJ+WFbU948BP2EBt6+NBAtv7HW4AX9vT0famJfWEjwq8
ftmcFOSNGgYcDQ5BwQWX1sFhnwb9XSfurlQsVYBsFA4cx4gj0DfUm1Ugr4wDD+lo
91P+76hSBQ+mHp1HJ90WMd2vAaElG7/SoaicXo9pW6Rc7WIgTjk7gg==
=SdZy
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-9jul19-take2' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm
- Sandbox improvements including .dts refactor
- Minor tracing and PCI improvements
- Various other minor fixes
- Conversion of patman, dtoc and binman to support Python 3
'Bootloader Control Block' (BCB) is a well established term/acronym in
the Android namespace which refers to a location in a dedicated raw
(i.e. FS-unaware) flash (e.g. eMMC) partition, usually called "misc",
which is used as media for exchanging messages between Android userspace
(particularly recovery [1]) and an Android-capable bootloader.
On higher level, this allows implementing a subset of Android Bootloader
Requirements [2], amongst which is the Android-specific bootloader
flow [3]. Regardless how the latter is implemented in U-Boot ([3] being
the most memorable example), reading/writing/dumping the BCB fields in
the development process from inside the U-Boot is a convenient feature.
Hence, make it available to the users.
Some usage examples of the new command recorded on R-Car H3ULCB-KF
('>>>' is an overlay on top of the original console output):
=> bcb
bcb - Load/set/clear/test/dump/store Android BCB fields
Usage:
bcb load <dev> <part> - load BCB from mmc <dev>:<part>
bcb set <field> <val> - set BCB <field> to <val>
bcb clear [<field>] - clear BCB <field> or all fields
bcb test <field> <op> <val> - test BCB <field> against <val>
bcb dump <field> - dump BCB <field>
bcb store - store BCB back to mmc
Legend:
<dev> - MMC device index containing the BCB partition
<part> - MMC partition index or name containing the BCB
<field> - one of {command,status,recovery,stage,reserved}
<op> - the binary operator used in 'bcb test':
'=' returns true if <val> matches the string stored in <field>
'~' returns true if <val> matches a subset of <field>'s string
<val> - string/text provided as input to bcb {set,test}
NOTE: any ':' character in <val> will be replaced by line feed
during 'bcb set' and used as separator by upper layers
=> bcb dump command
Error: Please, load BCB first!
>>> Users must specify mmc device and partition before any other call
=> bcb load 1 misc
=> bcb load 1 1
>>> The two calls are equivalent (assuming "misc" has index 1)
=> bcb dump command
00000000: 62 6f 6f 74 6f 6e 63 65 2d 73 68 65 6c 6c 00 72 bootonce-shell.r
00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00 y.r.............
>>> The output is in binary/string format for convenience
>>> The output size matches the size of inspected BCB field
>>> (32 bytes in case of 'command')
=> bcb test command = bootonce-shell && echo true
true
=> bcb test command = bootonce-shell- && echo true
=> bcb test command = bootonce-shel && echo true
>>> The '=' operator returns 'true' on perfect match
=> bcb test command ~ bootonce-shel && echo true
true
=> bcb test command ~ bootonce-shell && echo true
true
>>> The '~' operator returns 'true' on substring match
=> bcb set command recovery
=> bcb dump command
00000000: 72 65 63 6f 76 65 72 79 00 73 68 65 6c 6c 00 72 recovery.shell.r
00000010: 79 00 72 00 00 00 00 00 00 00 00 00 00 00 00 00 y.r.............
>>> The new value is NULL-terminated and stored in the BCB field
=> bcb set recovery "msg1:msg2:msg3"
=> bcb dump recovery
00000040: 6d 73 67 31 0a 6d 73 67 32 0a 6d 73 67 33 00 00 msg1.msg2.msg3..
00000050: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
00000060: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
>>> --- snip ---
>>> Every ':' is replaced by line-feed '\n' (0xA). The latter is used
>>> as separator between individual commands by Android userspace
=> bcb store
>>> Flush/store the BCB structure to MMC
[1] https://android.googlesource.com/platform/bootable/recovery
[2] https://source.android.com/devices/bootloader
[3] https://patchwork.ozlabs.org/patch/746835/
("[U-Boot,5/6] Initial support for the Android Bootloader flow")
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
There is no good reason to limit the trace buffer to 2GiB on a 64bit
system. Adjust the types of the relevant parameters.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This pull request provides error fixes for the graphical output protocol,
the text output protocol, and the extended text input protocol.
Setting the boot device for the bootefi command is now not only supported
by the 'load' command but also for the file system specific commands like
'fatload'.
-----BEGIN PGP SIGNATURE-----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=GvWF
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc5-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc5 (3)
This pull request provides error fixes for the graphical output protocol,
the text output protocol, and the extended text input protocol.
Setting the boot device for the bootefi command is now not only supported
by the 'load' command but also for the file system specific commands like
'fatload'.
efi_status_t and int are of different size. Use separate variables for
return codes of different type.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
fatload command can be used to load the EFI payload since EFI system
partition is always a FAT partition. Call into EFI code from do_load()
to set the device path from which the last binary was loaded. An EFI
application like grub2 can’t find its configuration file without the
device path set.
Since device path is now set in do_load() there is no need to set it
in do_load_wrapper() for the load command.
Signed-off-by: Mian Yousaf Kaukab <ykaukab@suse.de>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In order to use CMD_SF / CMD_SPI / ENV_IS_IN_SPI_FLASH we need to have
the SPI (or SPI_FLASH/DM_SPI_FLASH, for CMD_SF) enabled. Express this
in the Kconfigs.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2C9f
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20190606' of https://github.com/pchotard/u-boot
- Add Ethernet support for STM32MP1
- Add saveenv support for STM32MP1
- Add STM32MP1 Avenger96 board support
- Add SPI driver suport for STM32MP1
- Add watchdog support for STM32MP1
- Update power supply check via USB TYPE-C for STM32MP1 discovery board
Introduce ENV_IS_IN_DEVICE to test if one the
CONFIG_ENV_IS_IN_ is defined and support the command
saveenv even if CONFIG_ENV_IS_NOWHERE is activated
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Support for managing the non-volatile attribute of UEFI variables
is added though we do not have a backend for persistence yet.
Error messages for changes of UEFI variables are provided.
UEFI boottime service implementations are corrected.
-----BEGIN PGP SIGNATURE-----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=mCc9
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc4-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc4-2
Support for managing the non-volatile attribute of UEFI variables
is added though we do not have a backend for persistence yet.
Error messages for changes of UEFI variables are provided.
UEFI boottime service implementations are corrected.
current implementation for checking if "led list"
command is called checks only if "l" is passed to the
led command. This prevents switching leds with name
which starts also with a "l". So check for passing
"list".
While at it, also fix a typo in led command usage.
Signed-off-by: Heiko Schocher <hs@denx.de>
With this option, -nv, at "setenv -e" command, a variable will be defined
as non-volatile.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Boot####, BootOrder and BootNext should be non-volatile.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Error message will alert a user that setting/deleting a variable failed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Corrections for boottime services for protocols and for the SetTime()
service are provided.
Error messages for the 'setenv -e' and 'bootefi bootmgr' commands are
added.
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEbcT5xx8ppvoGt20zxIHbvCwFGsQFAlzziRQACgkQxIHbvCwF
GsRFwA/9HJejIxx8TjMBAixuV0QRpvNlSqT4UNruDxDn1+UELDLzXAm2hinY07lR
l58ztrzcFx6dUcTWR13P7vVItaGKoIyDTHKfdKbdtUC5OQzApu9/Crb5/+NPf2cS
bxuFVEtrgvdJ9HdtF5SxTevnJK8MXnb8ho8QmYr+rPC5AMAOPWBnMMiWuS330TAW
znxiWN+Hiy1q9+0peAHRcvTl0gheRrEUHqdluKdLOEwdJul3XjQlvOG87QAcuTOx
+Y6VPDl91E6WKIofILDMfCBLVVsEw5ruoW2e1Vo23UxtIkTkDtop0qe46wBAzsJe
blEFtvOXaAPikuL9x2aGO2nwk2q87tRzbS5pEGWspWW/PX72k94Vgw4R9NXj9Wpp
UPpG4BK2Eu1YohomHa/zmaJPdRUYg2cP34N1YAbLrEX9Ro7Nhmf+cBgckbR+GRuF
C95hBCzRNYpPV9BRHZlLG58yiTN/OUcTRSA87dENycA9WFqI8LRlLfkn8BYBwUwO
KhFMLOjUViYvu+t+HcqBSQWwLN7Iw0F8lOfRQkJ1EFym29QNpWH6HjykAKN3SwUn
b+r2ZDBwtwqGxZfUcaJHjc1ZPtzYEF7F3csrnicO5F+nN0oQvd8zBSHylDbvwAzd
L392XREU4gB5Z/qxPjRFZdlVRgRmE36bNc7jcezT/qeD7Cl7z9I=
=A8+f
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc4' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc4
Corrections for boottime services for protocols and for the SetTime()
service are provided.
Error messages for the 'setenv -e' and 'bootefi bootmgr' commands are
added.
Alex reported the following:
"
I'm doing some MDIO work on a freescale/NXP platform and I bumped into
errors with this command:
=> mdio r emdio#3 5 3
Reading from bus emdio#3
"Synchronous Abort" handler, esr 0x8600000e
elr: ffffffff862b8000 lr : 000000008200cce4 (reloc)
...
mdio list does not list any PHYs currently because ethernet is using DM
and the interfaces are not probed at this time. The PHY does exist
on the bus though.
The above scenario works with this commit reverted:
e55047ec51 cmd: mdio: Switch to generic
helpers when accessing the registers
The current code using generic helpers only works for PHYs that have
been registered and show up in bus->phymap and crashes for arbitrary
IDs. I find it useful to allow reading from other addresses over MDIO
too, certainly helpful for people debugging MDIO on various boards.
"
Fix this by reverting to use the raw MDIO bus operations in case there
is no PHY probed based on DT at the specified address.
This restores the old behavior for these PHYs, which means that the
newly introduced MMD-over-C22 helpers won't be available for them, but
at least they will be accessible again without crashing the system.
Fixes: commit e55047ec51 ("cmd: mdio: Switch to generic helpers when accessing the registers")
Reported-by: Alex Marginean <alexm.osslist@gmail.com>
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Alex Marginean <alexm.osslist@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Error message will alert a user that setting/deleting a variable failed.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Compiling the display command leads to an error
undefined reference to `display_set'
No implementation of display_set() exists in U-Boot.
Eliminate the `display` command as well as the accompanying files.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use the new hex2bin function in the binop command instead of converting
the data manually.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
Since the binop command was introduced, the environment API was changed.
Use the new API to make the command work again.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.
Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
Describe that efi_install_fdt() defaults to using the device tree
indicated by environment variable fdtcontroladdr.
ACPI tables and device trees are mutually exclusive.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The device path to text protocol is not needed for EBBR compliance. So
let's make it a customizable option.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
There is no 'config CRC32', remove the select that was attempting to use
it.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
This patch adds booti support for RISC-V Linux kernel. The existing
bootm method will also continue to work as it is.
It depends on the following kernel patch which adds the header to the
flat Image. Gzip compressed Image (Image.gz) support is not enabled with
this patch.
https://patchwork.kernel.org/patch/10925543/
Tested on HiFive Unleashed and QEMU.
Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Karsten Merker <merker@debian.org>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Switch to use the generic helpers to access the MMD registers so that we
can used the same command also for C45 PHYs, C22 PHYs with direct and
indirect access and PHYs implementing a custom way to access the
registers.
Signed-off-by: Carlo Caione <ccaione@baylibre.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
allow_unaligned(), switch_to_non_secure_mode(), and efi_init_obj_list() are
called in sequence in multiple places.
Move calls to allow_unaligned() and switch_to_non_secure_mode() to
efi_init_obj_list().
Remove unused includes.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The list of PXE default paths contains ARCH and SOC specific paths, but
one PXE server can serve different board with the same ARCH and SOC.
This is the case for Turris Omnia and Turris Mox, where ARCH=arm and
SOC=mvebu.
If CONFIG_SYS_BOARD is defined, also try "default-$ARCH-$SOC-$BOARD"
path.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
The "Mode :" line is the only one in "mmc info" output that has a
space in front of the colon. Drop the space to make it consistent
with the rest of the output, e.g.:
=> mmc dev 1 ; mmc info
switch to partitions #0, OK
mmc1 is current device
Device: sd@ee160000
Manufacturer ID: 3
OEM: 5344
Name: SL08G
Bus Speed: 50000000
Mode : SD High Speed (50MHz)
^------------------------------ Remove this space
Rd Block Len: 512
SD version 3.0
High Capacity: Yes
Capacity: 7.4 GiB
Bus Width: 1-bit
Erase Group Size: 512 Bytes
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
CC: Tom Rini <trini@konsulko.com>
clk_get_rate may return -ENODEV if the clock isn't valid.
Also, make the error cases go through a single path.
Fixes: ff8eee0330 ("cmd: clk: Add trivial implementation of clock dump
for DM")
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
Reviewed-by: Matthias Brugger <mbrugger@suse.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
-----BEGIN PGP SIGNATURE-----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=GUpA
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc2
This pull request provides error fixes for the handling of GPT partitions
and for the UEFI subsystem.
Apply the following changes:
- Guard the 'gpt read' command by 'ifdef CONFIG_CMD_GPT_RENAME',
since 'gpt read' is not available on CMD_GPT_RENAME=n
- Prefix the {read,swap,rename} commands with one space for consistency
- Prefix the 'guid' commands with 'gpt' for consistency
Signed-off-by: Eugeniu Rosca <erosca@de.adit-jv.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In case of a failure exit data may be passed to Exit() which in turn is
returned by StartImage().
Let the `bootefi` command print the exit data string in case of an error.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When printing an UEFI variable an error may arise while converting an
illegal hexadecimal value. In this case a buffer is leaked.
Close the memory leak. Provide an error message.
Reported-by: Coverity (CID 185830)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The field boot OptionalData in structure _EFI_LOAD_OPTIONS is for binary
data.
When we use `efidebug boot add` we should convert the 5th argument from
UTF-8 to UTF-16 before putting it into the BootXXXX variable.
When printing boot variables with `efidebug boot dump` we should support
the OptionalData being arbitrary binary data. So let's dump the data as
hexadecimal values.
Here is an example session protocol:
=> efidebug boot add 00a1 label1 scsi 0:1 doit1 'my option'
=> efidebug boot add 00a2 label2 scsi 0:1 doit2
=> efidebug boot dump
Boot00A0:
attributes: A-- (0x00000001)
label: label1
file_path: .../HD(1,MBR,0xeac4e18b,0x800,0x3fffe)/doit1
data:
00000000: 6d 00 79 00 20 00 6f 00 70 00 74 00 69 00 6f 00 m.y. .o.p.t.i.o.
00000010: 6e 00 00 00 n...
Boot00A1:
attributes: A-- (0x00000001)
label: label2
file_path: .../HD(1,MBR,0xeac4e18b,0x800,0x3fffe)/doit2
data:
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently in do_efi_boot_dump(), we directly read EFI variables from
related environment variables. To accommodate alternative storage
backends, we should switch to using the UEFI API instead.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
UEFI variables should be installed using well-defined API.
Currently we don't support much, but the value of OsIndicationsSupported
will be updated once some features are added in the future.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Add comments. Rename a variable.
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Rockchip use 'arch-rockchip' instead of arch-$(SOC) as common
header file path, so that we can get the correct path directly.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
AVB 2.0 spec. revision 1.1 introduces support for named persistent values
that must be tamper evident and allows AVB to store arbitrary key-value
pairs [1].
Introduce implementation of two additional AVB operations
read_persistent_value()/write_persistent_value() for retrieving/storing
named persistent values.
Correspondent pull request in the OP-TEE OS project repo [2].
[1]: https://android.googlesource.com/platform/external/avb/+/android-9.0.0_r22
[2]: https://github.com/OP-TEE/optee_os/pull/2699
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Sam Protsenko <semen.protsenko@linaro.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@gmail.com>
The objective is to provide a simple way to retrieve a BMP file,
and display it as splashscreen, from extlinux.conf file input.
For this, we take example on https://www.syslinux.org/wiki/
index.php?title=Menu#The_advanced_menu_system
and more particularly on MENU BACKGROUND chapter.
For this, add "menu background" support in pxe command.
As example, extlinux.conf content will look like:
# Generic Distro Configuration file generated by OpenEmbedded
menu title Select the boot mode
TIMEOUT 20
menu background ../splash.bmp
DEFAULT stm32mp157c-ev1-sdcard
LABEL stm32mp157c-ev1-sdcard
KERNEL /uImage
FDT /stm32mp157c-ev1.dtb
APPEND root=/dev/mmcblk0p6 rootwait rw earlyprintk console=ttySTM0,115200
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
This reverts commit 65a97e7fcf.
The 'eeprom' command has been converted to work with DM_I2C in a patch
submitted around the same time as this commit:
commit 0c07a9b407 ("eeprom: Add device model based I2C support to eeprom command")
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
The current device model enabled eeprom code only works if
CONFIG_SYS_I2C_EEPROM_BUS is set.
This patch makes it work without that define so that the bus
number passed to 'eeprom_init' is used.
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlzAfvkACgkQfxc6PpAI
reYu9AgAjaFmydXjE8DxkSB3rR7DHZFTs1erVKAAL2v+Tdf7LDmz+j6u1M3v55WY
6r54f/gZ1UX5TEmQgEAKLa7QvvRO/lNvSGQnLHhZhv2IVWo7uWCKAUPdQ6XVZnUK
zO5v+ucs9Ne4HxQJHMC509HUIIBbydiRvUm8W0SeBZy4kEyJDuub4L+rpARkXNks
IZfKuY+VS4FK73D4M9PIhoXSubZgVS4AEcapakU1DvEz0kjsN4wr4idGrp3lutPC
455imz83JBq2+mx1oxclOGedkIDzTCq+nWQAwSftMehrJpGrp7RLNo0v4QZZUf4V
LIXRqObIYse9yQLkYPpeBdePMc8/tQ==
=0NJ2
-----END PGP SIGNATURE-----
Merge tag 'pull-24apr19' of git://git.denx.de/u-boot-dm
Various minor sandbox iumprovements
Fixes for tracing with sandbox
Refactoring for boot_get_fdt()
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
-----BEGIN PGP SIGNATURE-----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=caQ+
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-3' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (3)
This patch series reworks the implementation of the `bootefi` command to
remove code duplication by using the LoadImage() boot service to load
binaries.
Missing short texts for UEFI protocols are added for display by the
`efidebug dh` command.
Missing parameter checks for AllocatePages() and CreateDeviceNode() are
implemented.
The constants for protocol GUIDs are changed to match the names in the UEFI
specification.
When using boot scripts it can become quite hard to understand
which commands are actually executed during bootup (e.g. where
is a kernel image loaded from or which DTB is in use).
Shell scripts suffer from a similar problem and many shells address
this problem with a command execution tracer (e.g. BASH has xtrace,
which can be enabled by "set -x").
This patch introduces a command tracer for U-Boot, which prints
every command with its arguments before it is executed.
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The EBBR specification prescribes that we should have either an ACPI table
or a device tree but not both. Let us enforce this condition in the
`bootefi` command.
If the bootefi command is called without a device tree parameter use a
previously device tree or fall back to the internal device tree.
The fdt unit test should not be run on boards with an ACPI table.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In the current implementation, bootefi command and EFI boot manager
don't use load_image API, instead, use more primitive and internal
functions. This will introduce duplicated code and potentially
unknown bugs as well as inconsistent behaviours.
With this patch, do_efibootmgr() and do_boot_efi() are completely
overhauled and re-implemented using load_image API.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Use efi_root as parent handle for the loaded image.
LoadImage() should be called with BootPolicy = true by the boot manager.
Avoid duplicate free_pool().
Eliminate variable memdp which is not needed after anymore due to
"efi_loader: correctly split device path of loaded image".
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
All the non-boot-manager-based (that is, bootefi <addr>) code is put
into one function, do_bootefi_image().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
do_bootmgr_exec() is renamed to do_efibootmgr() as we put all the necessary
code into this function.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Efi_selftest code is unusual in terms of execution path in do_bootefi(),
which make that function complicated and hard to understand. With this
patch, all efi_selftest related code will be put in a separate function.
The change also includes expanding efi_run_prepare() and efi_run_finish()
in do_bootefi_exec().
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
For simplicity, merge two functions.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Return error code of efi_install_configuration_table() when aborting from
efi_install_fdt().
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This is a preparatory patch for reworking do_bootefi() in later patch.
Carve out a function to handle the installation of the device tree
as a configuration table in system table.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
set_load_options() can fail, so it should return error code to stop
invoking an image.
In addition, set_load_options() now takes a handle, instead of
loaded_image_info, to utilize efi_load_image() in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The `efidebug dh` command shows handles and the installed protocols. For
most of the protocols implemented by U-Boot a short text was shown. But for
some only the GUID was displayed.
Provide the missing short texts for the following protocols: HII String,
HII Database, HII Config Routing, Simple Network, PXE Base Code.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We should consistently use the same name for protocol GUIDs as defined in
the UEFI specification. Not adhering to this rule has led to duplicate
definitions for the EFI_LOADED_IMAGE_PROTOCOL_GUID.
Adjust misnamed protocol GUIDs.
Adjust the text for the graphics output protocol in the output of the
`efidebug dh` command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This function supports getting both data address and length for
existing FIT subimage and FIT external data.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
The 'exception' command allows to test exception handling.
This implementation supports ARM, x86, RISC-V and the following exceptions:
* 'breakpoint' - prefetch abort exception (ARM 32bit only)
* 'unaligned' - data abort exception (ARM only)
* 'undefined' - undefined instruction exception
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reload the watchdog in the mass storage command ums
to avoid reboot during the usb waiting loop
when the host doesn't send any request.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
The compiler is not happy when neither USB nor TFTP transport for DFU defined:
cmd/dfu.c: In function ‘do_dfu’:
cmd/dfu.c:31:8: warning: unused variable ‘devstring’ [-Wunused-variable]
char *devstring = argv[3];
^~~~~~~~~
cmd/dfu.c:30:8: warning: unused variable ‘interface’ [-Wunused-variable]
char *interface = argv[2];
^~~~~~~~~
Surround those variables by #ifdef expression.
More serious, that comes under same circumstances, is a compilation error due
to absence of macro parameter:
In file included from include/image.h:45,
from include/common.h:35,
from cmd/dfu.c:13:
include/command.h:207:24: error: expected expression before ‘,’ token
# define _CMD_HELP(x) x,
^
include/command.h:286:18: note: in expansion of macro ‘_CMD_HELP’
_cmd, _usage, _CMD_HELP(_help) _CMD_COMPLETE(_comp) }
^~~~~~~~~
include/command.h:290:3: note: in expansion of macro ‘U_BOOT_CMD_MKENT_COMPLETE’
U_BOOT_CMD_MKENT_COMPLETE(_name, _maxargs, _rep, _cmd, \
^~~~~~~~~~~~~~~~~~~~~~~~~
include/command.h:332:2: note: in expansion of macro ‘U_BOOT_CMD_COMPLETE’
U_BOOT_CMD_COMPLETE(_name, _maxargs, _rep, _cmd, _usage, _help, NULL)
^~~~~~~~~~~~~~~~~~~
cmd/dfu.c:70:1: note: in expansion of macro ‘U_BOOT_CMD’
U_BOOT_CMD(dfu, CONFIG_SYS_MAXARGS, 1, do_dfu,
^~~~~~~~~~
make[1]: *** [scripts/Makefile.build:279: cmd/dfu.o] Error 1
make: *** [Makefile:1518: cmd] Error 2
Put empty string unconditionally to have macro parameter present.
Fixes: 0f44d33536 ("dfu: Fix up the Kconfig mess")
Cc: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Lukasz Majewski <lukma@denx.de>
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAly262oACgkQykllyylKDCH44gCbBnuxUH6ZF0B7Leuee4te7C59
LmUAn14/bbtMt17zkMSADCjY9yGWF4au
=mWrW
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2019.07' of git://git.denx.de/u-boot-microblaze
Xilinx/FPGA changes for v2019.07
fpga:
- Add support for external data in FIT
- Extend testing for external data case
- Inform user about a need to run post config on Zynq
arm:
- Tune zynq command functions
- Fix internal variable setting
arm64:
- Add support for zc39dr decoding
- Disable WDT for zcu100
- Small changes in reset_reason()
- Some DT changes (spi)
- Tune qspi-mini configuration
- Remove useless eeprom setting
- Fix two sdhci boot case
spi:
- Fix tap delay programming
clk:
- Enable i2c in SPL
net:
- Fix gem phydev handling
- Remove phy detection code from gem driver
general:
- Correct EXT_DTB usage for MULTI_DTB_FIT configuration
This function supports getting both data address and length for
existing FPGA subimage and FPGA external data.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
-----BEGIN PGP SIGNATURE-----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=QdJl
-----END PGP SIGNATURE-----
Merge tag 'efi-2019-07-rc1-2' of git://git.denx.de/u-boot-efi
Pull request for UEFI sub-system for v2019.07-rc1 (2)
In the aarch64 crash dump information about the loaded EFI images is added.
In README.uefi the development target is for the UEFI subsystem is
described as "Embedded Base Boot Requirements (EBBR) Specification"
compliance.
Several bug fixes are supplied.
Following Ard's suggestion:
Runtime data sections are intended for data that is used by the runtime
services implementation.
Let's change the type to EFI_BOOT_SERVICES_DATA.
This also fixes booting of armv7 using efi and fdtcontroladdr.
Suggested-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch update the behavior introduced by
commit 96907c0fe5 ("dm: spi: Read default speed and mode values from DT")
In case of DT boot, don't read default speed and mode for SPI from
CONFIG_* but instead read from DT node. This will make sure that boards
with multiple SPI/QSPI controllers can be probed at different
bus frequencies and SPI modes.
Remove also use in boards of the value speed=0 (no more supported)
for ENV in SPI by using CONFIG_ENV_SPI_MAX_HZ=0.
DT values will be always used when available (full DM support of
SPI slave with available DT node) even if speed and mode are requested;
for example in splash screen support (in splash_sf_read_raw)
or in SPL boot (in spl_spi_load_image).
The caller of spi_get_bus_and_cs() no more need to force speed=0.
But the current behavior don't change if the SPI slave is not
present (device with generic driver is created automatically)
or if platdata is used (CONFIG_OF_PLATDATA).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Add a command to control the watchdog devices. This is useful if the
watchdog is rather long running (eg. seconds) and it should be
controlled by scripts. It is also handy during debugging.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The command line is:
ln <interface> <dev[:part]> target linkname
Currently symbolic links are supported only in ext4 and only if the option
CMD_EXT4_WRITE is enabled.
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Current code is plain wrong, and there's no need to have a mutable string,
so fix function type and remove the intermediate variable.
Signed-off-by: Ismael Luceno <ismael.luceno@silicon-gears.com>
A misplaced return statement lead to a memory leak in
efi_dump_single_var().
Reported-by: Coverity (CID 185829)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
In `efidebug boot add iPXE scsi 0:1 snp-arm64.efi --foo` a parameter is
missing. Hence the command should not silently return as if everything were
ok but should display the usage info.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Alexander Graf <agraf@csgraf.de>
"drivers" command prints all the uefi drivers on the system.
=> efi drivers
Driver Name Image Path
================ ==================== ====================
000000007ef003d0 <NULL> <built-in>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"devices" command prints all the uefi variables on the system.
=> efi devices
Scanning disk ahci_scsi.id0lun0...
Scanning disk ahci_scsi.id1lun0...
Found 4 disks
Device Device Path
================ ====================
000000007ef07ea0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)
000000007ef00c10 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)
000000007ef00dd0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)
000000007ef07be0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)/HD(1,MBR,0x086246ba,0x800,0x40000)
000000007ef07510 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(1,0)/HD(2,MBR,0x086246ba,0x40800,0x3f800)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, there is no easy way to add or modify UEFI variables.
In particular, bootmgr supports BootOrder/BootXXXX variables, it is
quite hard to define them as u-boot variables because they are represented
in a complicated and encoded format.
The new command, efidebug, helps address these issues and give us
more friendly interfaces:
* efidebug boot add: add BootXXXX variable
* efidebug boot rm: remove BootXXXX variable
* efidebug boot dump: display all BootXXXX variables
* efidebug boot next: set BootNext variable
* efidebug boot order: set/display a boot order (BootOrder)
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
"env [print|set] -e" allows for handling uefi variables without
knowing details about mapping to corresponding u-boot variables.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Without CONFIG_LED, we get
cmd/built-in.o: In function `show_led_state':
cmd/led.c:40: undefined reference to `led_get_state'
cmd/built-in.o: In function `do_led':
cmd/led.c:99: undefined reference to `led_get_by_label'
cmd/led.c:108: undefined reference to `led_set_state'
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Allow the 'gpio' command to match GPIO bank names regardless of the case
of each. While these are generally in upper case, it is useful to be able
to provide lower case with the command.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present the gpio command only shows GPIOs which are marked as in use.
This makes sense with 'gpio status' since we already have the '-a' flag
to indicate that all GPIOs should be shown. But when a particular GPIO is
requested, it seems better to always display it. At present the request is
simply ignored.
For example if GPIO a10 is not in use, then:
> gpio status a10
shows nothing, not even the function being used for that GPIO. With this
change, it shows the pin status:
> gpio status a10
a10: input: 0 [ ]
Add an extra parameter for this to avoid changing the existing flag
parameter.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
[bmeng: correct the 'gpio' command in the commit message]
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Arguments are const and belong to the caller. Calling date in a hush
loop will yield different results from the second invocation.
Signed-off-by: Roman Kapl <rka@sysgo.com>
Currently there are two problems in 'bootelf -p' (load elf by segments)
command:
- bss section is not flushed, so booted elf can have non zero values
in bss;
- at least on ARM there are 'CACHE: Misaligned operation at
range...' warnings
Use p_memsz instead of p_filesz during cache flushing for elf segment.
p_filesz doesn't include zero initialized memory (e.g. bss section),
which also should be flushed.
Align these cache flushes to line boundaries.
Signed-off-by: Kurban Mallachiev <mallachiev@ispras.ru>
Free resources upon failure.
Correct the function description.
As there is no need for any special address in the dummy memory device
path passed via the EFI_LOADED_IMAGE_PROTOCOL simply use 0 as address.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
`bootefi selftest` fails on qemu-x86_defconfig if efi_selftest() is not
invoked using EFI_CALL().
Likewise we call the entry point of EFI payloads with
EFI_CALL(efi_start_image()).
entry_count indicates if we are in U-Boot (1) or in EFI payload code (0).
As we start in U-Boot code the initial value has to be 1.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Remove the duplicate code in efi_do_enter() and use efi_start_image() to
start the image invoked by the bootefi command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Up to now efi_load_pe() returns the entry point or NULL in case of an
error. This does not allow to return correct error codes from LoadImage().
Let efi_load_pe() return a status code and fill in the entry point in the
corresponding field of the image object.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
This patch fixes the int-to-pointer-cast warning on aarch64.
Signed-off-by: Adam Heinrich <adam@adamh.cz>
Signed-off-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Matthias Brugger <mbrugger@suse.com>
Refactor the switch from supervisor to hypervisor to a new function called
at the beginning of do_bootefi().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The function, efi_init_obj_list(), can be shared in different pseudo efi
applications, like bootefi/bootmgr as well as my efishell. Moreover, it
will be utilized to extend efi initialization, for example, my "removable
disk support" patch and "capsule-on-disk support" patch in the future.
So with this patch, it will be moved to a new file, efi_setup.c, under
lib/efi_loader and exported, making no changes in functionality.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Remove lines deactivated by #if 1 #else
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
debug() support supports %p to print pointers.
The debug message is unique. So there is not need to write a possibly
distracting line number.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
It should not be necessary to adjust CMD_BOOTEFI_HELLO_COMPILE in config
files.
arch/arm/lib/crt0_arm_efi.S cannot be compiled in thumbs mode. We can
disable CMD_BOOTEFI_HELLO_COMPILE for CONFIG_CPU_V7M. So there is no longer
a need to disable it in stm32 configs.
helloworld.efi can be built without problems on x86_64. So there is no need
to disable it in chromebook_link64_defconfig and qemu-x86_64_defconfig.
Same is true for ARM V7A. So do not disable CMD_BOOTEFI_HELLO_COMPILE in
kp_imx6q_tpc_defconfig.
Some architecture checks are already make for EFI_LOADER. There is no need
to repeat them for CMD_BOOTEFI_HELLO_COMPILE
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Patrice.Chotard@st.com
Signed-off-by: Alexander Graf <agraf@suse.de>
When calling efi_dp_from_mem() use a named constant for the memory type.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Calling sata_scan() with a null pointer probably won't make much sense.
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present this file uses GPIO_OUTPUT and GPIO_INPUT as its sub-command
values. These are pretty generic names. Add a 'C' suffix to avoid possible
conflicts.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The imgextract command runs a number of checks of
the specified fit. Where it checks for a load address
for compressed images the logic in the expression
is inverted as fit_image_check_comp returns 1 on
success and not 0.
cmd/mtd.c:447:13: warning: ‘mtd_help_text’ defined but not used [-Wunused-variable]
static char mtd_help_text[] =
^~~~~~~~~~~~~
When SYS_LONGHELP is not defined. After looking at how other commands
work, we should surround the whole help text (even its declaration) with
an #ifdef CONFIG_SYS_LONGHELP, since it's compiled out when calling
_CMD_HELP[1] on the help text variable argument to U_BOOT_CMD.
[1] https://elixir.bootlin.com/u-boot/latest/source/include/command.h#L181
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
And you get sub-command auto-completion for free.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It's way simpler this way, and we also gain auto-completion support for
free (MTD name auto-completion has been added with mtd_name_complete())
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The repeatable property is currently attached to the main command and
sub-commands have no way to change the repeatable value (the
->repeatable field in sub-command entries is ignored).
Replace the ->repeatable field by an extended ->cmd() hook (called
->cmd_rep()) which takes a new int pointer to store the repeatable cap
of the command being executed.
With this trick, we can let sub-commands decide whether they are
repeatable or not.
We also patch mmc and dtimg who are testing the ->repeatable field
directly (they now use cmd_is_repeatable() instead), and fix the help
entry manually since it doesn't use the U_BOOT_CMD() macro.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
test->time_ms[] is defined as unsigned. So use %u for printf().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
gpio is defined as unsigned int. So we should use %u when calling printf().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make sure the block cache is cleared for the MMC device after it was
reinitialized to avoid having any stale data in the cache, like e.g.
partition tables or such.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
In case the card is removed, force-init the MMC to start the internal
machinery which deregisters and invalidate the MMC device.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Current CBFS component type list is incomplete. Add missing ones.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present there are 2 macros that are named as CBFS_COMPONENT_xxx.
Change them to CBFS_TYPE_xxx for consistency.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The sound driver pulls together the audio codec and i2s drivers in order
to actually make sounds. It supports setup() and play() methods. The
sound_find_codec_i2s() function allows locating the linked codec and i2s
devices. They can be referred to from uclass-private data.
Add a uclass and a test for sound.
Signed-off-by: Simon Glass <sjg@chromium.org>
In case SYS_I2C or DM_I2C are defined, then the "i2c " prefix
of the "i2c crc32" command is missing.
This patch addresses this, so that users can't get confused
by the "crc32" command.
Without the patch we get
=> i2c help
i2c - I2C sub-system
Usage:
i2c bus [muxtype:muxaddr:muxchannel] - show I2C bus info
crc32 chip address[.0, .1, .2] count - compute CRC32 checksum
i2c dev [dev] - show or set current I2C bus
[...]
With the patch we get
=> i2c help
i2c - I2C sub-system
Usage:
i2c bus [muxtype:muxaddr:muxchannel] - show I2C bus info
i2c crc32 chip address[.0, .1, .2] count - compute CRC32 checksum
i2c dev [dev] - show or set current I2C bus
...
Signed-off-by: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The implementation of the EEPROM commands does not support the DM I2C API.
Prevent compilation breakage by not enabling it if the non-DM API is not
available (if DM_I2C is used without DM_I2C_COMPAT)
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add 2 functions to wrap the calls to board_usb_init() and
board_usb_cleanup().
This is a preparatory work for DM support for UDC drivers (DM_USB_GADGET).
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Hi,
setting active menuitem currently can be outside of menu which results in invisible selection
attached Patch fixes this
regards Frank
>From 1d9c4cb8b3e2dd9b0a7a6a2d4a21684d0a099dbf Mon Sep 17 00:00:00 2001
From: Frank Wunderlich <frank-w@public-files.de>
Date: Sun, 2 Dec 2018 11:23:53 +0100
Subject: [PATCH] ensure active menuitem is inside menu
if active menuitem is defined via environment var it can be outside the menu (>=menuitem-count)
this patch resets this definition back to 0
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Allow to display BMP at the middle of the screen.
'm' means "middle" as it is done for the splashscreen variable:
splashpos=m,m
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add common clear screen command for configurations
CONFIG_DM_VIDEO, CONFIG_LCD and CONFIG_CFB_CONSOLE.
Remove the existing cls command implementation from
lcd.c code and activate the command for all boards
enabling CONFIG_LCD for compatibility reasons.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Tested-by: Patrick.Delaunay <patrick.delaunay@free.fr>
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=6o9t
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-12-03
This release is fully packed with lots of glorious improvements in UEFI
land again!
- Make PE images more standards compliant
- Improve sandbox support
- Improve correctness
- Fix RISC-V execution on virt model
- Honor board defined top of ram (fixes a few boards)
- Imply DM USB access when distro boot is available
- Code cleanups
When copying the device we must ensure that the copy does not fall into a
memory area reserved by the same.
So let's change the sequence: first create memory reservations and then
copy the device tree.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The sandbox is using a virtual address space which is neither the physical
address space of the operating system nor the virtual address space in
which Linux aplications live. The addresses used insided the flattened
device tree use this sandbox virtual address space. The EFI subsystem uses
the virtual address space of the operating system and this is where the fdt
is stored.
Fix all incorrect addresses for the fdt in cmd/bootefi.cmd.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
When allocating EFI memory pages the size in bytes has to be converted to
pages.
Provide a macro efi_size_in_pages() for this conversion.
Use it in the EFI subsystem and correct related comments.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
This function can be used from do_bootefi_exec() so that we use mostly the
same code for a normal EFI application and an EFI test.
Rename the function and use it in both places.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
There is still duplicated code in efi_loader for tests and normal
operation.
Add a new bootefi_run_prepare() function which holds common code used to
set up U-Boot to run EFI code. Make use of this from the existing
bootefi_test_prepare() function, as well as do_bootefi_exec().
Also shorten a few variable names.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The functions in bootefi are very long because they mix high-level code
and control with the low-level implementation. To help with this, create
functions which handle preparing for running the test and cleaning up
afterwards.
Also shorten the awfully long variable names here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present a few error conditions are not checked. Before refactoring
this code, add some basic checks. Note that this code still leaks memory
in the event of error. This will be tackled after the refactor.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The "Devicetree Specification 0.2" does not prescribe that memory
reservations must be EFI page aligned. So let's not make such an
assumption in our code.
Do not carve out the pages for the device tree. This memory area is
already marked as EFI_RUNTIME_SERVICES_DATA.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In copy_fdt() we allocate EFI pages for the fdt plus extra 12 KiB as
EFI_RUNTIME_SERVICES_DATA. Afterwards in efi_install_fdt() we overwrite
part of this memory allocation by marking it as EFI_BOOT_SERVICES_DATA.
Remove the code marking the fdt as EFI_BOOT_SERVICES_DATA.
Cf. commit 17ff6f02f5 ("efi_loader: store DT in EFI_RUNTIME_SERVICES_DATA
memory")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Factor out efi_set_bootdev() and extract efi_dp_from_name().
This function will be used to set a boot device in efishell command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Rename the component parent of some EFI objects to header. This avoids
misunderstandings.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
All our handles point to a struct efi_object. So let's define the
efi_handle_t accordingly. This helps us to discover coding errors much
more easily. This becomes evident by the corrections to the usage of
handles in this patch.
Rename variable image_handle to image_obj where applicable.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
At present many TPM calls assume there is only one TPM in the system and
look up this TPM themselves. This is inconsistent with driver model, which
expects all driver methods to have a device parameter. Update the code to
correct this.
Signed-off-by: Simon Glass <sjg@chromium.org>
store fdt header member with name <member> in U-Boot
Environment variable with name <var>.
for example to get the total length of the fdt and store
it in filesize, call:
fdt header get filesize totalsize
For membernames look into fdt header definition at
scripts/dtc/libfdt/libfdt.h
Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
- spi_init_f
- spi_init_r
- spi_read
- spi_write
these spi calls are exclusively for mpc8xx, but
the relevant driver is not available so remove it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
with this patch the selected Entry in bootmenu can be set by
environment-var bootmenu_default=<number>
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
There is some basic informaton that SPL normally wants to pass through to
U-Boot, such as the SDRAM size and bank information.
Mkae use of the new bloblist structure for this. Add a new 'handoff' blob
which is set up in SPL and passed to U-Boot proper. Also adda test for
sandbox_spl that checks that this works correctly and a new 'sb' command
to show the information passed from SPL.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
The old 'sb' command was deprecated in 2015 and replaced with 'host'. It
is useful to be able to access some internal sandbox state, particularly
for testing.
Resurrect the old command and provide a way to print some basic state
information (currently just the arguments to sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
The old 'sb' command was deprecated in 2015 and replaced with 'host'.
Remove the remaining users and the command, so that the name is available
for other purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Its only called from this file, so make it static. While at it, remove
some occurances of multiple blank lines as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Boris Brezillon <boris.brezillon@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch fixes the address information of fdt.
wrong case:
=> fdt addr 0x48000000
=> fdt move 0x48000000 0x41000000 0xa000
=> fdt addr
The address of the fdt is 48000000
Active address in this case is 0x41000000.
Signed-off-by: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Hiroyuki Yokoyama <hiroyuki.yokoyama.vx@renesas.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Pantelis Antoniou <pantelis.antoniou@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add new option to 'adc' command to do a single scan of:
- some channel(s), using mask argument
- all channels available on an ADC device (when optional mask is omitted).
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use newly introduced adc_raw_to_uV() API to print conversion result
both as raw value and micro-volts by default.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Enhance adc info command to report also the channel mask.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
pinmux command allows to :
- list all pin-controllers available on platforms
- select a pin-controller
- display the muxing of all pins of the current pin-controller
or all pin-controllers depending of given options
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
cmd: pinmux: Fix pinmux command
if "pinmux status" command is used without having
set dev using "pinmux dev", print pinmux usage
Reviewed-by: Simon Glass <sjg@chromium.org>
Display all digits on 64bit systems. Currently we print only the lower
32 bits. Examples of values that can exceed 32 bits are the size and start of
memory banks.
For fdt_blob use the same output method as for other values. This avoids
misalignment.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add 'virtio' command in U-Boot command line.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
part_init() is currently called in every DM BLK driver, either
in its bind() or probe() method. However we can use the BLK
uclass driver's post_probe() method to do it automatically.
Update all DM BLK drivers to adopt this change.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Commit c58fb2cdb3 ("cmd: ubi: clean the partition handling")
introduced a call to mtd_probe_devices() in the ubi_attach() path
and this function takes care of parsing mtdparts/mtdids and
creating/registering the associated mtd partitions.
The mtdparts_init() call in the ubi_detach() path is not only
unnecessary but can sometimes print error messages even when things
work properly (that's the case with SPI NAND devices that have not
been probed with 'mtd list'), which is misleading.
Remove this call to mtdparts_init() and drop the dependency on
CMD_MTDPARTS.
Fixes: c58fb2cdb3 ("cmd: ubi: clean the partition handling")
Reported-by: Stefan Roese <sr@denx.de>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Tested-by: Stefan Roese <sr@denx.de>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
gwventana configs are relying on CMD_UBI to select CMD_MTDPARTS,
which is then making {MTDIDS,MTDPARTS}_DEFAULT options available.
We are about to remove the 'select CMD_MTDPARTS' statement in the
CMD_UBI entry, but if we do that without first making sure
{MTDIDS,MTDPARTS}_DEFAULT are visible, we end up with a build
failure when building gwventana configs.
Address that by adding a depends on MTD_PARTITIONS to
{MTDIDS,MTDPARTS}_DEFAULT which does the trick since CMD_UBI selects
MTD_UBI which in turn selects MTD_PARTITIONS.
We also get rid of the depends on CMD_MTD, since CMD_MTD also selects
MTD_PARTITIONS.
Reported-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This line is no more needed and can be removed.
Only CONFIG_CMD_SOURCE is defined in Kconfig and
used in defconfig files.
CONFIG_SOURCE if not defined in source code and
"config SOURCE" is not present in any Kconfig.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Currently the base is 3 fix it 10 so that IDs follow decimal system.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvulta@ti.com>
All mii operations require a valid PHY address except the 'device'
command, which expects the PHY name rather than the address.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
A few bug fixes for the 2018.11 release:
- Fix block seeking on 32bit
- Fix execution with DEBUG set
- Fix a few Coverity found bugs
- Fix warnings
Heinrich Schuchardt (13):
efi_loader: fix relocation on x86_64
efi_loader: correct signature of GetPosition, SetPosition
efi_loader: execute efi_save_gd() first
efi_loader: efi_allocate_pool(EFI_ALLOCATE_ANY_PAGES, ...)
efi_loader: error handling in read_console()
efi_loader: return type efi_console_register()
efi_loader: superfluous statement in is_dir()
efi_loader: memory leak in efi_set_variable()
efi_loader: remove lcd.h from efi_net.c
arm: do not include efi_loader.h twice
efi_loader: fix typo in efi_boottime.c
efi_selftest: creating new handle in controller test
efi_loader: efi_dp_get_next_instance() superfluous statement
Tom Rini (2):
efi_loader: Fix warning in efi_load_image()
fs: fat: Fix warning in normalize_longname()
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=CIpq
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-2018.11' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-10-17
A few bug fixes for the 2018.11 release:
- Fix block seeking on 32bit
- Fix execution with DEBUG set
- Fix a few Coverity found bugs
- Fix warnings
Heinrich Schuchardt (13):
efi_loader: fix relocation on x86_64
efi_loader: correct signature of GetPosition, SetPosition
efi_loader: execute efi_save_gd() first
efi_loader: efi_allocate_pool(EFI_ALLOCATE_ANY_PAGES, ...)
efi_loader: error handling in read_console()
efi_loader: return type efi_console_register()
efi_loader: superfluous statement in is_dir()
efi_loader: memory leak in efi_set_variable()
efi_loader: remove lcd.h from efi_net.c
arm: do not include efi_loader.h twice
efi_loader: fix typo in efi_boottime.c
efi_selftest: creating new handle in controller test
efi_loader: efi_dp_get_next_instance() superfluous statement
Tom Rini (2):
efi_loader: Fix warning in efi_load_image()
fs: fat: Fix warning in normalize_longname()
If DEBUG is defined we may be calling EFI_CALL already during the
initialization of the EFI subsystem. We must make sure efi_save_gd() has
already been called at that moment.
Anyway it is better to have this call in one location instead of three.
This fixes an illegal memory access occurring since 4e6b5d6503
("efi_loader: create root node") with DEBUG = 1.
Fixes: 4e6b5d6503 ("efi_loader: create root node")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Sandbox SPL/TPL support
Various dm-related improvements
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAlu9RL4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYd8gf+NYAGhpiEZZ5vc3DB4Xdn2okgakbbg0QQ
/b0Lr9xQsKgZthK0rvPlH2dXxf+ViAm1iHTy8KBCFi0SHNder48Zui9uTrX0NRq8
pLZGyJPXPYbiyc4pQTEJpTth4iShcphRVio0no4sLpNQqO4aQrialSLa9fnwd9Ra
1l9mF91aaYw6cG+/ejg3UR1LfsDdQ5bjubt0Fw0wGX9UvQOAz5gz5+a17wrz6+Gx
L0gzvyfbuLUhbWB36DXikrL14DAFys2uV9aHJ5zEd53l+F7ZHWsupCO0OtN66cV7
KpPKoYG7vhLqBXKpyrW20T+BPeSyDKmDQE6wbpECmEDOvKzvW67O/w==
=Bfjm
-----END PGP SIGNATURE-----
Merge tag 'dm-9oct18' of git://git.denx.de/u-boot-dm
Test improvements to tidy up output and drop duplicate tests
Sandbox SPL/TPL support
Various dm-related improvements
When updating the board FDT, some of the operations
are performed by ft_board_setup_ex() and should be
executed also by the fdt command.
Signed-off-by: Nicholas Faustini <nicholas.faustini@azcomtech.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
At present the mtrr functions disable the cache before making changes and
enable it again afterwards. This is fine in U-Boot, but does not work if
running in CAR (such as we are in SPL).
Update the functions so that the caller can request that caches be left
alone.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
This file has changed quite a bit in the last 5 years as the capabilities
of the ECs have grown. Sync it up with the copy in coreboot commit
b9141f2215.
The only change is the addition of EC_VBNV_BLOCK_SIZE_V2. This is needed
because U-Boot uses the new v2 vboot API and this is not currently fully
supported by Chromium OS firmware.
Signed-off-by: Simon Glass <sjg@chromium.org>
These are needed for the 2018 version of Chromium OS vboot. Add an
implementation for TPM v1, with v2 to come later.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we pass around a private pointer to specify the cros_ec device.
With driver model it makes more sense to pass the device. Update the code
to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a way in configuration files (exlinux.conf for sysboot command)
to select a specific FIT configuration. The configuration is selected
with a string added after the FIT filename in the label "KERNEL" or
"LINUX", using the same format than bootm command:
KERNEL [Filename]#<conf>[#<extra-conf[#...]]
This configuration string, beginning by '#', is directly appended
to bootm argument 1 after <kernel_addr_r>.
bootm [<kernel_addr_r>]#<conf>[#<extra-conf[#...]]
see doc/uImage.FIT/command_syntax_extensions.txt for details
Example :
KERNEL /fit.itb#cfg1
KERNEL /fit.itb#cfg2
Configuration can be use also for overlay management :
KERNEL /fit.itb#cfg1#dtbo1#dtbo3
see doc/uImage.FIT/overlay-fdt-boot.txt for details
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Prior to this patch was do_avb_write_rb() reading supplied rb_idx as a
hexadecimal number while do_avb_read_rb() printed the read out rb_idx as
decimal number. For consistency change do_avb_read_rb() to print rb_idx
as a hexadecimal number too.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Igor Opaniuk <igor.opaniuk@linaro.org>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Since the mach_id is not used by RISC-V, remove it.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Lukas Auer <lukas.auer@aisec.fraunhofer.de>
This is the PR for SPI-NAND changes along with few spi changes.
[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'mtdparts' command is not needed anymore. While the environment
variable is still valid (and useful, along with the 'mtdids' one), the
command has been replaced by 'mtd' which is much more close to the MTD
stack and do not add its own specific glue.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
UBI should not mess with MTD partitions, now that the partitions are
handled in a clean way, clean the ubi command and avoid using this
uneeded extra-glue to reference the devices.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
There should not be a 'nand' command, a 'sf' command and certainly not
a new 'spi-nand' command. Write a 'mtd' command instead to manage all
MTD devices/partitions at once. This should be the preferred way to
access any MTD device.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Boris Brezillon <boris.brezillon@bootlin.com>
Prevent cache warning messages when using the 'bootelf' command on an
Arm target. Round down each section start address and round up the
respective section end to the nearest cache line.
Signed-off-by: Neil Stainton <nstainton@asl-control.co.uk>
[trini: Manually apply, rework whitespace]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add trivial implementation of the clk dump in case DM is enabled.
This implementation just iterates over all the clock registered
with the CLK uclass and prints their rate.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Ley Foon Tan <ley.foon.tan@intel.com>
Previously poweroff was located under boot. It seems to make more
sense to have it located under the Device access commands.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add basic command for bus information and read for onewire
bus using Dallas 1-Wire protocol.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
cmd_ubifs_mount() function would be called directly instead of
involving whole command machinery for mounting ubifs in
generic firmware loader, so some checking codes need to be factored out
into cmd_ubifs_mount() without breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
cmd_ubifs_umount() function would be called directly instead of involving
whole command machinery in generic firmware loader, so checking on
ubifs_initialized status need to be done in cmd_ubifs_umount() without
breaking original functionality design.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
[trini: Fix conflicting type error in cmd/ubi.c]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add command to query information from and write text to on-screen
display (OSD) devices.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABAgAGBQJbq6+cAAoJECszeR4D/txgV1cP+wZPVsY/kRDwCZ8PODOIyLW/
YWWX0CHOUNIXcvWyrQQVflRKE7IbsoPNU+PxOze/toBZvNGZofCqd/P0sT0kk8UU
/aQ55+Hn8/N4etysKxhk2uszBuEXZsOdprNV3H7tO9vKsMHpImAdLvIyviYK0eCF
WnNsmDVFv/W4M5IWDJrS7KqwTuLPYE5Xli9BW/O2qi8NOvpfyb4EEqdL7OHyHAxe
8zpzyaRXJkPcgPkJ6z3WZ+BmAuXSl5DsLWqfsnZJQzkXatRhT8PneRk787e+xK3A
OEFarj5t/94T1KivxquM9iYi0NzwGWrrCfRzbQh5klV4Z/bRYHbGQ92j6iZyfnpj
0zvWrJCalDaUz310BKZDyzKYQnoDj5/iYaMJHtaG6zmkXCzM41kniGKxuy/3IpTB
ozeFtH2AOwlAFZRIzQiazkyU0bizis2Y/K4xzOQczvVajdLW0DsLXL/hyqaFaGO2
3oVK350FXMHKa1UhpsG05aoQvyYq8N4YVEfOSdBKah8qhhMG8zZ2IaX5oheZJjr4
yPV8iaSj8trX3mI9clsnX9YT7qJdcS188JYSii+8SVpVH4VpgwvUSHfDqznn7JNz
COue6rFo9sg55Le9OsoxUgaQ5GO4oz+5iGmfyBmOtQ3n83JxmP4CJK84Ykw2i9fi
sxJR6aNtktsLhfYhlDO/
=ZuJG
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-09-26
A lot of goodness in this release. We're *very* close to running the
UEFI Shell and SCT natively. The only missing piece are HII protocols.
- FAT write support (needed for SCT)
- improved FAT directory support (needed for SCT)
- RTC support with QEMU -M virt
- Sandbox support (run UEFI binaries in Linux - yay)
- Proper UTF-16 support
- EFI_UNICODE_COLLATION_PROTOCOL support (for UEFI Shell)
- EFI_SIMPLE_TEXT_INPUT_EX_PROTOCOL support (for UEFI Shell)
- Fix window size determination
- Fix Tegra by explicitly unmapping RAM
- Clean up handle entanglement
- Lots of generic code cleanup
[trini: Fixup merge conflict in include/configs/qemu-arm.h]
Signed-off-by: Tom Rini <trini@konsulko.com>
The 'conitrace' command prints the codes received from the console input as
hexadecimal numbers.
This developer utility is useful for testing the handling of special keys
by keyboard drivers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
