Commit graph

31 commits

Author SHA1 Message Date
Manish Narani
15ca9ebb07 arm64: zynqmp: Move USB3 PHY properties from DWC3 node to USB node
Move the PHY properties from DWC3 node to USB node in ZynqMP DTs as here
the USB3 PHY used is PSGTR, which is connected to Xilinx USB core. This
PHY initialization should be handled from Xilinx USB core as the
prerequisite register configurations are done here only.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-07-26 09:26:41 +02:00
Michal Simek
52caf2c12b arm64: zynqmp: Remove gpio from aliases list
It is not recommended to have aliases for gpio. In past it was used in
Linux for assigning numbers via sysfs which is deprecated and libgpiod
should be used instead.
In U-Boot this number is used for seq number but gpio offset are not
counted from this number. That's why having these aliases only for seq
number is not needed. As is done in Linux it is the best to use full gpio
name instead of sequence number which depends on sequence in binding.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:36 +02:00
Michal Simek
e0f99280ee arm64: zynqmp: Remove information about dma clock on zcu106
Clock setting is not static anymore that's why it depends on firmware setup
that's why remove this comment.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
43086886ad arm64: zynqmp: Remove si5328 and si5382 nodes
There are no drivers for these devices that's why remove that nodes
completely. This change is done based on Linux kernel.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Link: https://lore.kernel.org/r/20210308115437.2232847-1-quanyang.wang@windriver.com
2021-06-23 09:48:35 +02:00
Michal Simek
531abcb71e xilinx: Convert xlnx,eeprom property to nvmem alias
Convert all boards to use nvmem alias instead of xlnx,eeprom. The change is
done based on discussion in the link below.

Link: https://lore.kernel.org/r/CAL_JsqLMDqpkyg-Q7mUfw-XH67-v068Q6e9wTq2UOoN=0-_coQ@mail.gmail.com
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
5fa9672248 arm64: zynqmp: Sync psgtr location on zcu100/zcu106
psgtr node should be below pinctrl for easier comparion among dts files.
That's why move that nodes to different location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
184309b8c6 arm64: zynqmp: Add maximum-speed property for dwc3 nodes
dwc3 can be used only for higher speeds than super-speed that's why
explicitly set it up.
This is also aligned with other ZynqMP dts files.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
447fb8db02 arm64: zynqmp: Update Copyright years to 2021
Trivial change for all files I have touched recently.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
f2b5dd38de arm64: zynqmp: Move DP nodes to the end of file (zcu106)
Just sync it with others for easier comparison.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
1242a6b13d arm64: zynqmp: Update psgtr clocks index for boards
Update the psgtr clock indexing for couple of zynqmp boards.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-06-23 09:48:35 +02:00
Michal Simek
3195840c94 arm64: zynqmp: Add psgtr DT descriptions
Mainline kernel has psgtr driver that's why it is good to add description
to DT files. Some boards are just missing description for USB3 and sata.
zc1751-dc1 and p-a2197 are also missing clock descriptions for input
clocks.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-05-19 09:44:50 +02:00
Michal Simek
bd00849ae9 arm64: zynqmp: Add pinctrl description
ZynqMP pinctrl Linux driver has been merged to 5.13-rc1 kernel. Based on it
DT files can be extended by pinctrl configurations.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-05-19 09:44:50 +02:00
Michal Simek
ce90654d1c xilinx: Sync DTs with Linux kernel
There are several changes which happen in mainline kernel which should get
also to U-Boot. Here is the list of patches from the kernel:

- ARM: zynq: Fix leds subnode name for zc702/zybo-z7
- arm64: dts: zynqmp: Fix leds subnode name for zcu100/ultra96 v1
- arm64: dts: zynqmp: Fix u48 si5382 chip on zcu111
- arm64: dts: zynqmp: Wire up the DisplayPort subsystem
- arm64: dts: zynqmp: Add DisplayPort subsystem
- arm64: dts: zynqmp: Add DPDMA node
- arm64: dts: zynqmp: Enable phy driver for Sata on zcu102/zcu104/zcu106
- arm64: dts: zynqmp: Enable si5341 driver for zcu102/106/111
- arm64: dts: zynqmp: Add DT description for si5328 for zcu102/zcu106
- arm64: dts: zynqmp-zcu100-revC: correct interrupt flags
- arm64: dts: xilinx: align GPIO hog names with dtschema
- arm64: zynqmp: Add Xilinx AES node
- dt: bindings: dma: xilinx: dpdma: DT bindings for Xilinx DPDMA

but also some other changes have been done.
- Using only one compatible string for adxl345 on zturn
- Remove Xilinx internal DP bindings
- Remove USB3.0 serdes configurations
- Remove SATA serdes configuration for zc1232
- Resort nvmem_firmware
- Update nand compatible string
- Aling power-domains property for sd0/1

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2021-03-30 12:03:24 +02:00
Michal Simek
01a6da1661 xilinx: Fix xlnx,mio_bank property
s/xlnx,mio_bank/xlnx,mio-bank/g

DT binding is describing mio-bank not mio_bank that's why fix all DTSes and
also driver itself.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
2020-08-20 09:49:20 +02:00
Michal Simek
5df63a60aa arm64: zynqmp: Fix addresses in partition definitions
Node name should be <name>@<address> which is not how partitions are
described.

Issue was found by running dtbs_check as:
flash@0: 'partition@qspi-device-tree', 'partition@qspi-fsbl-uboot',
'partition@qspi-linux', 'partition@qspi-rootfs'
do not match any of the regexes: ...

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Manish Narani
12ffe75819 arm64: zynqmp: Add 'no-1-8-v' property for ZynqMP Boards
Modify dts files to add 'no-1-8-v' property for all the ZynqMP boards.
User can remove this property to enable the UHS mode. This is to keep
the same speed (HS) modes across all the stages of the Linux Boot. Due
to power cycling limitation of some of the ZynqMP boards, some SD cards
don't get power cycled and are failing in Linux.

Signed-off-by: Manish Narani <manish.narani@xilinx.com>
2020-04-06 12:51:31 +02:00
Michal Simek
d31f1c9236 arm64: zynqmp: Update Copyright years to 2020
Trivial change.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-04-06 12:51:31 +02:00
Sudeep Holla
ad967af6bd arm64: dts: zynqmp: replace gpio-key,wakeup with wakeup-source property
Most of the legacy "gpio-key,wakeup" boolean property is already
replaced with "wakeup-source". However few occurrences of old property
has popped up again, probably from the remnants in downstream trees.

This patch replaces the legacy properties with the unified
"wakeup-source" property introduced by:
"Input: gpio_keys - switch to using generic device properties"
(sha1: 700a38b27eefc582099fdf69effacfad0ad738a4)

Cc: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:56 +01:00
Michal Simek
096d7f5b3e arm64: dts: zynqmp: Fix node names which contain "_"
s/_/-/ for node names.

It fixes warnings like this:
... Warning (node_name_chars_strict): /cpu_opp_table:
Character '_' not recommended in node name ...

Issues reported by make dtbs W=12

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:55 +01:00
T Karthik Reddy
166fb46ad3 zynqmp: dts: Cleanup no-1-8-v property from sdhci dt nodes
Removed no-1-8-v property from zynqmp sdhci devicetree nodes to
allow UHS-I capable SD cards to work in SD3.0 UHS modes.

Boards that does not have level shifter for SD, does not support 1.8v.
so no-1-8-v property to sdhci dt nodes should be present in zcu102 Rev-A,B,
zcu104 Rev-A,C, zcu100, zcu1275 Rev-B boards.

Signed-off-by: T Karthik Reddy <t.karthik.reddy@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2020-01-14 09:05:55 +01:00
Harini Katakam
631d9a9981 arm64: zynqmp: dt: Add missing DP83867 quirk
The DP83867 strap control workaround is already present in Linux kernel
mainline binding. All these Xilinx boards require this quirk.

Signed-off-by: Harini Katakam <harini.katakam@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Michal Simek
5c09709475 arm64: zynqmp: Add label property to all ina226 on zcu106
Label property is adding capability to distiguish chips from each other
when iio framework is used.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Michal Simek
777c4d69cb arm64: zynqmp: Enable iio-hwmon for ina226 on zcu106
ina226 hwmon driver is deprecated and it is recommended to use new iio
based driver. The patch is enabling iio-hwmon driver to export
functionality from IIO to hwmon interface to be able to use lm-sensors
package.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:02 +02:00
Michal Simek
2975a42b42 arm64: zynqmp: Use ethernet-phy as node name for ethernet phys
Ethernet phys based on devicetree specification should be using
ethernet-phy@ node name instead of pure phy@.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-10-24 13:37:01 +02:00
Neil Armstrong
ffd4c7c2ec dts: switch spi-flash to jedec, spi-nor compatible
There is no reason not to use the Linux "jedec,spi-nor" binding in U-Boot
dts files. This compatible has been added in sf_probe, let use it.

This patch switches to jedec,spi-nor when spi-flash is used in the DTS
and DTSI files, and removed spi-flash when jedec,spi-nor is already
present.

The x86 dts are switched in a separate commit since it depends on a change
in fdtdec.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Evgeniy Paltsev <paltsev@synopsys.com>
Reviewed-by: Rick Chen <rick@andestech.com>
Reviewed-by: Patrick Delaunay <Patrick.delaunay@st.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2019-04-12 10:54:27 +05:30
Michal Simek
1317a5e5ea arm64: zynqmp: Remove autodetected devices without description
It will never reach mainline that's why remove it.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2019-02-15 15:04:01 +01:00
Michal Simek
8bdad43333 arm64: zynqmp: Switch all platforms to DM_I2C
CONFIG_PCA953X is not needed because of PCA953X is integrated in gpio
subsystem already. That's why also remove CMD_PCA953X which is only for
this driver.

zcu102/zcu104-revC/zcu106/zcu111 contain links to eeprom which stores MAC address.

DM_I2C is not enabled for the whole SoC because it increase size for
mini configurations and there is no I2C symbol present to setup
dependencies.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
2019-02-14 14:31:10 +01:00
Michal Simek
6bd13ee94e arm64: zynqmp: Setup clock-output-names for si570 chips
If there are more instances of si570 clock-output-names property
should be used for differentiation of clock output.
The patch is adding this optional properties for all zynqmp boards with
si570 chip.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Michal Simek
0ed45f0025 arm64: zynqmp: Wire spi-flash compatible string with flashes
Enable reading tx and rx buswidth from DT via spi-uclass.
To get these from uclass spi-flash compatible string has to be added
to flash node.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-11-29 10:30:02 +01:00
Michal Simek
3c1eaec012 arm: zynq: Drop #address-cells and #size-cells from gpio-keys
dtc is showing some warnings and this change was also done in
the Linux kernel as "Input: gpio-keys - clean up device tree binding
example"
with this fragment in commit message
"Drop #address-cells and #size-cells, which are not required by the
gpio-keys binding documentation, as button sub-nodes are not devices."

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-06-15 08:06:31 +02:00
Michal Simek
cf0bcd7d02 arm64: zynqmp: Add support for Xilinx zcu106-revA
Xilinx zcu106 is a customer board. It is reusing some parts from zcu102.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
2018-04-09 12:14:52 +02:00