Update imx-atf and firmware-imx to latest released versions.
Update address of ATF_LOAD_ADDR that has changed to 0x970000 in imx-atf
commit 48733cb4e773a7584ced601de9d717efa3d73815.
Add 'O=' to make and build in separate directory as one issue has been noticed
where it was trouble building directly inside u-boot source dir. Restructure the workflow
and copy binaries after defconfig to ensure that build directory is created.
Signed-off-by: Peter Bergin <peter@berginkonsult.se>
Cc: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
The MX8M also contains a gigabit MAC, so define FEC_QUIRK_ENET_MAC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
CONFIG_SPL_LEGACY_IMAGE_SUPPORT is necessary for mx6sabresd and
mx6sabreauto, because u-boot is packed as legacy image not FIT.
However, this config is not set when CONFIG_SPL_LOAD_FIT is enabled.
Must enable it explicitly, otherwise will fail to boot like below.
U-Boot SPL 2021.04-rc2 (Feb 20 2021 - 16:43:04 -0800)
Trying to boot from MMC1
mmc_load_image_raw_sector: mmc block read error
SPL: failed to boot from all boot devices
Signed-off-by: Ye Li <ye.li@nxp.com>
On imx6Q/imx6DL, we find if config the DTOCV to 0~3, it will impact
cmd6 behavior, after cmd6 get transfer complete interrupt, the data0
line will keep low over 5 seconds. This should be a IC bug on imx6Q/DL.
For other platforms, do not has this issue.
To fix this issue, fix the DTOCV to 0xE, the max setting, this also align
with Linux configuration.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
I would like to help supporting this board, so add myself
as a maintainer.
Now that the board has been converted to DM, also add
its devicetree in the MAINTAINERS files entry.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Successfully tested booting Linux from the SD card.
Dropped splash screen support as this needs to be properly
converted to DM and tested.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Import the imx23-evk devicetree files from Linux kernel
version 5.11.
This is in preparation for converting the mx23evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Tested booting the Linux kernel from the SD card.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Import the imx51-babbage devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx51evk_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Add a compatible for i.MX51 so that i.MX51 can use this driver
via driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
The micro SD card slot uses GPIO3_13 as card detect pin, so describe
it in the devicetree.
This was noticed when converting imx53-qsb board to driver model
in U-Boot as the micro SD card was not getting detected.
After this change it is possible to load the dtb and zImage
from the SD card and boot Linux.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Make the conversion to driver model as it is mandatory.
Remove the SATA support for now as the i.MX53 support has not
been added yet.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Import the imx53-qsb devicetree files from Linux kernel
version 5.11-rc7.
This is in preparation for converting the mx53loco_defconfig
target to driver model.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
The RGMII link delays can be set on either MAC or PHY side. Set the
rgmii-id PHY mode for FEC and remove FEC_ENET_ENABLE_.XC_DELAY
setting, so that these definitions aren't used anymore throughout
the U-Boot.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Both NXP SoCs i.MX8 and i.MX8X have ENET gigabit MAC.
Define FEC_QUIRK_ENET_MAC for the imx8 platform and remove this
definition from configs of boards, based on MX8/MX8X.
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-By: Ramon Fried <rfried.dev@gmail.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Some compression algorithms currently can be enabled for SPL and
U-Boot proper separately. Therefore take into account USE_HOSTCC
is well as CONFIG_IS_ENABLED() in these cases to prevent compiling these
functions in case of a host tool build.
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Set default critical/alert temperature and enabling monoitoring.
Without calling imx_tmu_enable_msite() monitoring will not be enabled
and read_temperature will return 0. Additionally without setting alert
temperature will cause imx_tmu_get_temp() to spin indefiniately thinking
the system needs to cool.
This resolves the board spinning endlessly when enabling IMX_TMU in the
SPL.
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
The serial number OTP is similar to the imx7 version, except that the
register names are different. This also sets serial# directly, instead of
providing board_get_serial.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Some root filesystem configurations do not have separate /boot partition,
but rather place kernel, DT, scripts into /boot directory. Search the /boot
directory for these boot components in case they are not found in /, which
is the old behavior.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Replace filesystem specific fatload command with a filesystem agnostic
load command, so the board can boot from e.g. ext4 too.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Cc: uboot-imx <uboot-imx@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
There is now CONFIG_SPL_DM_SPI{,_FLASH}, however keeping
CONFIG_DM_SPI{,_FLASH} enabled in SPL seems to grow the SPL
by a couple of bytes:
text data bss dec hex filename
- 34069 1568 96 35733 8b95 spl/u-boot-spl
+ 34075 1568 96 35739 8b9b spl/u-boot-spl
In either case, the binary is bootable, so remove the part
in board config.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Enable DTO support to make it possible to boot fitImage with DTOs
embedded in them.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
This reverts commit 03a673cf49 ("dh_imx6: Switch to full DM-aware").
According to discussion [1], the patch is known to break the dh_imx6
board, however it made it upstream just before 2021.01-rc4, likely by
mistake. Revert this patch to put the board back into working order.
Also note that this board has no DM SPL support due to OCRAM size
limitations, but that is fine, as SPL DM support is optional.
[1] https://lists.denx.de/pipermail/u-boot/2020-June/417986.html
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andreas Geisreiter <ageisreiter@dh-electronics.de>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Ludwig Zenz <lzenz@dh-electronics.de>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@konsulko.com>
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAmA5DRwACgkQ4rK92eCq
k3WKtQf+Nk2N8XzhKgoz4dfg+A/uZ1ppKiuuYfHWitvw9OLrjGO61MnYOc6Dh7De
LchPExBYnatj3lxu3IEaaNUGJRujnt9n3W8JNQTGB81MI1TO2oITEhAyDqpMGtqt
pvr1NaoxhZM4B7n/HoQnVB+XtlP08w45SQiEXjjaO82hWRk45sAZ7WGFSs60iVck
ocqhrJ/2AraG98JQPxWfvdqr+24gl1Gt++KT/cdHS//IeYJJYuiCD3m9vOj8TatH
gDVbfR6tquZ5HLvKr/orRz3smaCuutWdHcDwcjs3kFK1rBHSYFZhG3qHQ3ZqNm+w
T/7JIqz4W366o7QZXXlCoi56w2tpug==
=f/Cg
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210226' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- Add USB host boot support in stm32mp1 config
- Enable uefi related commands for STMicroelectronics STM32MP15 boards
- Remove duplicate uart nodes in stm32mp15 device tree
The board can boot with UEFI. With the latest changes in U-Boot's
EFI subsystem we also have support for EFI runtime variables, without
SetVariable support. We can also store the EFI variables in a file on the
ESP partition and preserve them across reboots.
The env and efidebug commands are missing in order to configure
EFI variables and the efibootmgr though. Since U-Boot's default config
enables other EFI related commands (e.g bootefi), let's add the env related
and efidebug commands and allow users to do that
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Remove duplicated uart nodes introduced with commit 62f95af92a
("ARM: dts: stm32mp1: DT alignment with Linux kernel v5.9-rc4"),
because the uart nodes wasn't correctly ordered in alphabetic order.
Only cosmetic: the generated device tree don't change.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add support for booting from USB pen drive, since USB host port is
available on the STM32MP1.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Since commit 8745b9ebcc ("usb: gadget: add super speed support")
ums was no more functional on platform which use dwc2_udc_otg driver.
This was due to a too restrictive test which checked that the gadget
driver speed was either FS or HS.
So all gadget driver with max speed set to speed higher than
HS (SS in case of composite gadget driver in our case) are not
allowed, which is wrong.
Update the speed test in usb_gadget_register_driver() and in
dwc2_gadget_start() to allow all gadget driver speed equal or higher
than FS.
Tested on stm32mp157c-ev1 board.
Fixes: c791c8431c ("usb: dwc2: convert driver to DM_USB_GADGET")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
The OUT endpoint can just be ignored as it is not used, just as the
corresponding Set_Report request for IN-only interfaces. E.g. the
Linux gadget hid keyboard also provides an interrupt endpoint.
Also cleanup confusing debug messages like "found set protocol", which
is printed when a keyboard device is found, while the Set_Protocol request
is issued quite some time later.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
add support for the UUU commands ACmd and UCmd.
Enable them through the Kconfig option
CONFIG_FASTBOOT_UUU_SUPPORT
base was commit in NXP kernel
9b149c2a2882: ("MLK-18591-3 android: Add FSL android fastboot support")
and ported it to current mainline. Tested this patch
on imx6ul based board.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This documents the way U-Boot understands partitions specifications.
This also updates the fastboot documentation for the changes in the
previous commit.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This anchor is only for the k210 partition layout, so rename it
appropriately. This keeps it from conflicting with the (to be added)
anchor for U-Boot partitions in general.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for partitions of the form "dev.hwpart:part" and
"dev#partname". This allows one to flash to eMMC boot partitions without
having to use CONFIG_FASTBOOT_MMC_BOOT1_SUPPORT. It also allows one to
flash to an entire device without needing CONFIG_FASTBOOT_MMC_USER_NAME.
Lastly, one can also flash MMC devices other than
CONFIG_FASTBOOT_FLASH_MMC_DEV.
Because devices can be specified explicitly, CONFIG_FASTBOOT_FLASH_MMC_DEV
is used only when necessary for existing functionality. For those cases,
fastboot_mmc_get_dev has been added as a helper function. This allows
There should be no conflicts with the existing system, but just in case, I
have ordered detection of these names after all existing names.
The fastboot_mmc_part test has been updated for these new names.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This makes the next commit more readable by doing the move now.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The only thing mmcpart was used for was to pass to blk_dselect_hwpart.
This calls blk_dselect_hwpart directly from raw_part_get_info_by_name. The
error handling is dropped, but it is reintroduced in the next commit
(albeit less specificly).
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support for things like "#partname" and "0.1#partname". The block
device parsing is done like in blk_get_device_part_str.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds an option to part_get_info_by_dev_and_name_or_num to allow
callers to specify whether whole-disk partitions are fine.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Several functions in disk/part.c just return -1 on error. This makes them
return different errnos for different failures. This helps callers
differentiate between failures, even if they cannot read stdout.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This test verifies the mapping between fastboot partitions and partitions
as understood by U-Boot. It also tests the creation of GPT partitions,
though that is not the primary goal.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds support writing to the sandbox mmc backed by an in-memory
buffer. The unit test has been updated to test reading, writing, and
erasing. I'm not sure what MMCs erase to; I picked 0, but if it's 0xFF
then that can be easily changed.
Signed-off-by: Sean Anderson <sean.anderson@seco.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
- turris_mox: Enhancements, mostlly defconfig changes (Pali)
- pci-aardvark: Set Max Payload Size and Max Read Request Size
to 512 bytes (Pali)
- pci_mvebu: Minor cleanup and refactoring (Marek)
- Upgrade A38x DDR3 training to version 14.0.0 (Marek)
The relevant changes to the already existing GD5F1GQ4UExxG support has
been determined by consulting the GigaDevice product change notice
AN-0392-10, version 1.0 from November 30, 2020.
As the overlaps are huge, variable names have been generalized
accordingly.
Apart form the lowered ECC strength (4 instead of 8 bits per 512 bytes),
the new device ID, and the extra quad IO dummy byte, no changes had to
be taken into account.
New hardware features are not supported, namely:
- Power on reset
- Unique ID
- Double transfer rate (DTR)
- Parameter page
- Random data quad IO
The inverted semantic of the "driver strength" register bits, defaulting
to 100% instead of 50% for the Q5 devices, got ignored as the driver has
never touched them anyway.
The no longer supported "read from cache during block erase"
functionality is not reflected as the current SPI NAND core does not
support it anyway.
Implementation has been tested on MediaTek MT7688 based GARDENA smart
Gateways using both, GigaDevice GD5F1GQ5UEYIG and GD5F1GQ4UBYIG.
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
The datasheet only lists one dummy byte in the 0xEB operation for the
following chips:
* GD5F1GQ4xExxG
* GD5F1GQ4xFxxG
* GD5F1GQ4UAYIG
* GD5F4GQ4UAYIG
Reto Schneider:
- Linux patch ported to U-Boot
- Checked for compatibility with GD5F1GQ4xBxxG
- Fixed operation code in original commit message (0xEH -> 0xEB)
Signed-off-by: Reto Schneider <reto.schneider@husqvarnagroup.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
This line should come before the docs for the next function.
Fixes: 7aeedac015 ("mtd: spi: Port SPI NOR framework from Linux")
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
