Call pci_init() from board_init() to force PCI enumeration at probe time.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Since the new RevC LX2160A-RDB board has its 10G Aquantia PHYs at
different MDIO bus addresses, we must update both the kernel DTS and
u-boot's DTS (in case of DM_ETH) in case the board is indeed RevC or
newer. Use the newly introduced get_board_rev() function to trigger a
fixup of the kernel DTS to properly match the actual PHY addresses.
All this is encapsulated in the fdt_fixup_board_phy_revc() function
which will be used in the next patch.
Use the newly fdt_fixup_board_phy_revc() function introduced to
update both kernel's DTS and u-boot's DTS.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add new API for obtaining board revision and trigger the i2c node
fixup with this new API.
Signed-off-by: Florin Chiculita <florinlaurentiu.chiculita@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
It seems like the header inclusion guard for some Freescale crosspoint
switch header was misspelled.
Make the preprocessor symbol for the #ifndef and #define lines the
same, so that the double inclusion protection works as expected.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update DDR timing file generated by DDR Config Tool
1. Dynamic refresh rate is set by default
2. The 3rd freq will be 625MTS based on power and performance better than 100MTS.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add a static u-boot config for i.MX93 low drive mode support. When
low drive mode is enabled, VDD_SOC is set to 0.75V. Bus clocks,
A55 core clock (900Mhz), DDR clock (1866MTS), and some peripherals
clocks (USDHC/FLEXSPI/PDM/DISP_PIX/CAM_PIX) must decrease to meet
max frequencies in low drive mode.
Also set standby voltage for buck1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Move imx8 sci header file to include/firmware/imx, then we could
use build macro to reuse some i.MX8 drivers for i.MX9, such as
drivers/cpu/imx8_cpu.c.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stefano Babic <sbabic@denx.de>
pfuze_mode_init calls pmic_reg_read which is only available from
obj-$(CONFIG_$(SPL_TPL_)DM_PMIC) += pmic-uclass.o
Prepare for conversion of defined(CONFIG_DM_PMIC) to
CONFIG_IS_ENABLED(DM_PMIC).
Signed-off-by: Troy Kisky <troykiskyboundary@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is an existing CONFIG_MCFTMR Kconfig symbol,
use it and drop all other instances of CFG_MCFTMR.
This duality is likely a result of bogus conversion
to Kconfig.
Fixes: 7ff7b46e6c ("m68k: rename CONFIG_MCFTMR to CFG_MCFTMR")
Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
There is no need for the board file to instantiate a PL01X platform
device anymore. This is all taken care of by the DM code which now will
probe the device based on the DT node.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The EQoS interface mode is now configured in common board_interface_eth_init()
and called by EQoS MAC driver when appropriate. Drop the board side duplicates
if the same functionality.
Signed-off-by: Marek Vasut <marex@denx.de>
Since commit 1fa43cad86 ("video: Drop references to CONFIG_VIDEO et al")
the mx51evk_video.c is no longer used.
Remove the unused file.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Since commit 1fa43cad86 ("video: Drop references to CONFIG_VIDEO et al")
the mx53loco_video.c is no longer used.
Remove the unused file.
Signed-off-by: Fabio Estevam <festevam@denx.de>
The usage of DM_PMIC is preferred, so convert to it.
This also brings the benefit of causing a significant amount
of code removal.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The usage of DM_PMIC is preferred, so convert to it.
This also brings the benefit of causing a significant amount
of code removal.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
I don't have access to the mx6sxsabreauto board, so remove myself
from the MAINTAINERS entry and add Peng instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Acked-by: Peng Fan <peng.fan@nxp.com>
When using dual boot mode, the DDR won't be reset when APD power off
or reboot. It has possibility that obsolete fdt data existing on
fdt_addr_r address. Then even nothing in EFI partitions, the distro boot
still continue to parse fdt and get uboot crashed.
Clear the data at fdt_addr_r, so the fdt header check in above case
will not pass.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Bit0: Port 0 behavior when bandwidth maximized. Set to 1 to allow overflow
With overflow set, we see some issue that A35 may not able to get enough
bandwidth and A35 will report hrtimer takes too much time, workqueue
lockup. With overflow cleared, the issues are gone.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
To resolve DCNANO underrun issue, change the DDR Port 0 arbitration
from round robin fashion to fixed priority level 1, while other ports
are not assigned any priority, so they will be serviced in round robin
fashion if there is no active request from Port 0.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
This patch is used to support DBD owner fuse changed to S400 only.
The XRDC PDAC2 for LPAV pbridge5 and MSC1/2/3 for GPIO and LPAV are not
configured by S400 default setting. So these PDAC and MSC are invalid,
only DBD owner can access the corresponding resources.
We have to configure necessary PDAC and MSC for SPL before DDR
initialization.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
To fit the DBD_EN fused part, we re-design the TRDC and XRDC assignment.
M33 will be the TRDC owner and needs to configure TRDC. A35 is the
XRDC owner, ATF will configure XRDC.
The handshake between U-boot and M33 image is used to sync TRDC and
XRDC configuration completion. Once the handshake is done, A35 and M33
can access the allowed resources in others domain.
The handshake is needed when M33 is booted or DBD_EN fused, because both
cases will enable the TRDC. If handshake is timeout, the boot will hang.
We use SIM GPR0 to pass the info from SPL to u-boot, because before the
handshake, u-boot can't access SEC SIM and FSB.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
In both SPL and u-boot, after probing the S400 MU, get the chip revision,
lifecycle and UID from Sentinel.
Update get_cpu_rev to use the chip revision not hard coded it for A0
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This board is using floating point arithmetic to display
the SST39VF6401B flash size.
This actually generates errors with toolchains without
appropriate sw fp math functions available.
SST39VF6401B is the only flash for wich the size is displayed,
it's size is 8192KB and floating point calculation seems not
needed. Removing it.
Signed-off-by: Angelo Dureghello <angelo@kernel-space.org>
Now that DM_ETH is enabled by default, there is no point in keeping the
non-DM_ETH code which initialized the ethernet interfaces.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Now that DM_ETH is enabled by default, there is no point in keeping the
non-DM_ETH code which initialized the ethernet interfaces.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Now that DM_ETH is enabled by default, there is no point in keeping the
non-DM_ETH code which initialized the ethernet interfaces.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Now that DM_ETH is enabled by default, there is no point in keeping the
non-DM_ETH code which initialized the ethernet interfaces.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The LX2160ARDB board has support for DM_ETH probed devices, which means
that we do not need to manually create an MDIO controller, register it,
create PHYs on it etc.
In order to cleanup the board file a bit, just remove this code entirely.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
This converts 4 usages of this option to the non-SPL form, since there is
no SPL_FEC_MXC defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_TARGET_LX2160ARDB defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_DWC_ETH_QOS defined in Kconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
This option as well as CONFIG_TARGET_P1022DS and CONFIG_TARGET_P5020DS
are not defined anywhere. Drop them.
Signed-off-by: Simon Glass <sjg@chromium.org>
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/qoriq/qoriq-components/rcw:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP RCW github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
As explained in the text at the bottom of the page
https://source.codeaurora.org/external/imx/imx-atf:
"QUIC repositories on this site will not receive any updates after
March 31, 2022, and will be deleted on March 31, 2023."
Point to the NXP ATF github repo instead.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Reviewed-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
