- Multiples updates to the turris boards / platform
- Changes / enhancements to the Marvell PHY drivers, mainly
to support the turris platform
- Many fixes and enhancements to the pxa3xx NAND driver
- Fixes for the UART boot mode in kwboot
- Misc minor changes to other 32bit and 64bit boards
Add support for changing clock rate and parent clock for Armada 37xx
peripheral clocks.
Only clocks which can be disabled (.can_gate is true) can have parent
or rate changed.
This is needed so that Turris Mox can change SPI clock in device tree.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Signed-off-by: Stefan Roese <sr@denx.de>
Some TI Keystone 2 and K3 family of SoCs contain a system controller
(like the Power Management Micro Controller (PMMC) on 66AK2G SoCs and
the Device Management and Security Controller on AM65x SoCs) that manage
the low-level device control (like clocks, resets etc) for the various
hardware modules present on the SoC. These device control operations are
provided to the host processor OS through a communication protocol
called the TI System Control Interface (TI SCI) protocol.
This patch adds a clock driver that communicates to the system
controller over the TI SCI protocol for performing clock management of
various devices present on the SoC. Various clock functionality is
achieved by the means of different TI SCI device operations provided by
the TI SCI framework.
This code is loosely based on the drivers/clk/keystone/sci-clk.c driver
of the Linux kernel.
Reviewed-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
This patch adds support for :
- Rate calculation through muxes and generic dividers
- Basic gate setting propagation
- Reparenting for muxes
- Clock rate setting through generic dividers without reparenting
Support is only added to the Composite VPU and VAPB clocks in order
to support the Video Processing Unit Power Domain clock setup.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add clock driver for the Arria10, which allows reading the clock
frequency from all the clock described in the DT. The driver also
allows enabling and disabling the clock. Reconfiguring frequency
is not supported thus far.
Since the DT bindings for the SoCFPGA clock are massively misdesigned
and the handoff DT adds additional incorrectly described entries to
the DT, the driver contains workarounds which attempt to rectify all
of those problems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
In case the slow clock is not properly configured, the UTMI clock
cannot lock the PLL, because UPLLCOUNT will "wait X slow clock cycles".
In this case U-boot will loop indefinitely.
Added a timeout in this case, to start U-boot even if UTMI clock is
not enabled, so the user can use different media if needed, or investigate.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
sourcing of sub directiory kconfig files are not in
proper order, so keep them in ascending order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
The Assigned Clock parents and rates misses the fact that a "0" entry can
be passed to skip setting a parent or rate of an assigned clock as
described in the Linux clock bindings at [1].
This patch simply skips the clock reparenting if the DT parsing returns
-ENOENT and the clock rate setting if "0" is passed as clock rate.
[1] https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/clock/clock-bindings.txt#L135
Fixes: f4fcba5c5b "clk: implement clk_set_defaults()"
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add clk_valid() to check for optional clocks are valid.
Call clk_valid() in test/dm/clk.c and add relevant test routine to
sandbox clk tests.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
HSE and LSE bypass shall support both analog and digital signals.
This patch add a way to select digital bypas case in the device tree
and set the associated bit DIGBYP in RCC_BDCR and RCC_OCEN register
during clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add ADC clock gating, that may be used by STM32 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch add clk_enable/clk_disable/clk_get_rate support for
- DSI_PX
- LTDC_PX
- DSI_K (only get rate)
These clocks are needed for LTDC and DSI drivers with latest device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
the function compute the VCO PLL freq, used in
- stm32mp1_read_pll_freq()
- pll_set_rate()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
# Conflicts:
# drivers/clk/clk_stm32mp1.c
This patch define RCC_PLLNCFGR2_SHIFT to reuse it in
the pll function for set rate.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch fixed the same if/else part error by adding the required
source select on the basis of is_pre_src check.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit adds Actions Semi OWL family base clock and S900 SoC
specific clock support. For S900 peripheral clock support, only UART
clock has been added for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The PE clock have two parents, add support for picking the correct
one and deriving the clock from it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The PLL rate could be in the GHz range, which could overflow a 32bit
data type. Since the hardware is 64bit anyway, pass the clock rates
as 64bit number internally to avoid this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The mul and div arguments were reported in reverse order in the debug
message, swap them to fix this.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
dm_warn is too noisy, replace with dev_dbg for less noise.
Based on original work by Wenyou Yang
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Since b0ba1e7e9d
(rockchip: clk: rk3288: add clk_enable function and support USB HOST0/HSIC)
Ethernet no longer probes on RK3288.
Add no-ops for GMAC clocks observed to be requested which match the
clk_enable cases in RK3368 and RK3399.
Signed-off-by: Jonathan Gray <jsg@jsg.id.au>
Cc: Wadim Egorov <w.egorov@phytec.de>
Cc: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add support for the clk dump command on Armada 37xx.
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The drivers are based on Linux driver by Gregory Clement.
The TBG clocks support only the .get_rate method.
- since setting rate is not supported, the driver computes the rates
when probing and so subsequent calls to the .get_rate method do not
read the corresponding registers again
The peripheral clocks support methods .get_rate, .enable and .disable.
- the .set_parent method theoretically could be supported on some clocks
(the parent would have to be one of the TBG clocks)
- the .set_rate method would have to try all the divider values to find
the best approximation of a given rate, and it doesn't seem like
this should be needed in U-Boot, therefore not implemented
Signed-off-by: Marek Behun <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Add VREF clock gating, that may be used by STM32 VREFBUF regulator.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
On all STM32F4 and F7 SoCs family (except STM32F429), PLLSAI
output P can be used as 48MHz clock source for USB and SDMMC.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Tested By: Bruno Herrera <bruherrera@gmail.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have multiple licenses (in
these cases, dual license) declared in the SPDX-License-Identifier tag.
In this case we change from listing "LICENSE-A LICENSE-B" or "LICENSE-A
or LICENSE-B" or "(LICENSE-A OR LICENSE-B)" to "LICENSE-A OR LICENSE-B"
as per the Linux Kernel style document. Note that parenthesis are
allowed so when they were used before we continue to use them.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
The R8A7792 does not have the USB extal, so drop it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-sytems.com>
Parse of data in dedicated api instead of in probe().
The clk_set_rate() may be called before the clk driver is probed,
after core support set default clock.
This patch fix system abort issue since:
f4fcba5 clk: implement clk_set_defaults()
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The generic ehci-driver (ehci-generic.c) will try to enable the clocks
listed in the DTSI. If this fails (e.g. due to clk_enable not being
implemented in a driver and -ENOSYS being returned by the clk-uclass),
the driver will bail our and print an error message.
This implements a minimal clk_enable for the RK3288 and supports the
clocks mandatory for the EHCI controllers; as these are enabled by
default we simply return success.
Signed-off-by: Wadim Egorov <w.egorov@phytec.de>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The last clock consumer in SPL, SD/eMMC driver, gave up using the
clock driver. The clock driver is only used in U-Boot proper.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The initconst is not used in U-Boot, drop it. The r8a7794_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The initconst is not used in U-Boot, drop it. The r8a7792_crit_mod_clks
is also not used in U-Boot, so drop it too.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
