Use ePAPR defined properties for x86-uart: clock-frequency and
current-speed. Assign the value of clock-frequency in device tree
to plat->clock of x86-uart instead of using hardcoded number.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
There are many pci uart devices which are ns16550 compatible. We can
describe them in the board dts file and use it as the U-Boot serial
console as specified in the chosen node 'stdout-path' property.
Those pci uart devices can have their register be memory-mapped, or
i/o-mapped. The driver will try to use the memory-mapped register if
the reg property in the node has an entry to describe the memory-mapped
register, otherwise i/o-mapped register will be used.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The private data size is missing from the driver, so we store it at 0,
which causes problems when something overwrites memory at 0.
Fix this.
Change-Id: I6f551ee905b0064ae8343e41e46450c37c8c8c1a
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
pl010 & pl011 have different control register offsets, setting it as per
the pl01x type.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Receive line control uses same setting as transmit line control, also one lcrh
write is effective for both baud rate & receive line control internal update.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
UART_IBRD, UART_FBRD, and UART_LCR_H form a single 30-bit wide register which
is updated on a single write strobe generated by a UART_LCR_H write. So, to
internally update the content of UART_IBRD or UART_FBRD, a write to UART_LCR_H
must always be performed at the end.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
Although we were checking the pl01x type, seems like PL010 type was being
passed by mistake.
Signed-off-by: Vikas Manocha <vikas.manocha@st.com>
Acked-by: Simon Glass <sjg@chromium.org>
The same problem that is seen on some OMAP3 is also seen on some OMAP4
so include them in the test in order to prevent some hangs during SPL.
[trini: Re-word commit message, make apply cleanly]
Signed-off-by: Tom Rini <trini@ti.com>
This commit implements the ofdata_to_platdata handler for the UniPhier
serial driver and adds serial device nodes to the device tree sources.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The fdt_path_offset() checks an alias too.
fdtdec_get_alias_node(blob, "foo") is equivalent to
fdt_path_offset(blob, "foo").
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does. This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.
Many of references of those macros must be fixed to suppress warnings.
We have two options:
- Use min, max, min3, max3 only when the arguments have the same type
(or add casts to the arguments)
- Use min_t/max_t instead with the appropriate type for the first
argument
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
Provide a CONFIG_DM_STDIO option to enable registering a serial device
with the stdio library. This is seldom useful in SPL, so disable it by
default when building for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Add driver model support while retaining the existing legacy code. This
allows the driver to support boards that have converted to driver model
as well as those that have not.
Signed-off-by: Simon Glass <sjg@chromium.org>
Before adding driver model support, split out a few of the functions so
that they can be used by the driver model code.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Andreas Bießmann <andreas.devel@googlemail.com>
In general we can't store things in the data section until we have inited
SDRAM. Some platforms allow this (e.g. those with SPL) but some don't. Move
the pointer to global_data so that it will work on all platforms.
Without this fix the serial port will not work prior to relocation with
driver model on some platforms.
Signed-off-by: Simon Glass <sjg@chromium.org>
The same bit-field macros are defined in include/linux/serial_reg.h
so let's include it and delete duplicated defines.
Also, remove unnecessary inclusion of <common.h>.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add a driver for the designware serial UART used on sunxi. This just
redirects to the normal ns16550 driver.
Add a stdout-path to the device tree so that the correct UART is chosen.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This adds the preset value to register for R8A7793.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The UniPhier serial driver has been converted to driver model.
Let's remove uniphier_serial_initialize() call from the old
serial driver framework.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
This commit converts UniPhier on-chip serial driver to driver model.
Since UniPhier SoCs do not have Device Tree support, some board files
should be added under arch/arm/cpu/armv7/uniphier/ph1-*/ directories.
(Device Tree support for UniPhier platform is still under way.)
Now the base address and master clock frequency are passed from
platform data, so CONFIG_SYS_UNIPHIER_SERIAL_BASE* and
CONFIG_SYS_UNIPHIER_UART_CLK should be removed.
Tested on UniPhier PH1-LD4 ref board.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Commit b8893327e9 (dm: serial: Put common code into separate functions)
consolidated getc() and putc(). This commit does more puts() and tsts().
Also rename locally used functions to _serial_*() for clarification
because we have similar functions names here are there in this file.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The type (void *) can be directly passed to a function that
takes a specific pointer type.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Commit b8893327e9 (dm: serial: Put common code into separate functions)
consolidated getc() correctly, but introduced another bug to putc();
serial_stub_putc() passes sdev->priv to serial_putc_dev(), but
serial_putc_dev() uses cur_dev instead of the given argument.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The functions _serial_putc, _serial_putc_raw, _serial_puts,
_serial_getc, _serial_tstc, _serial_setbrg are defined and used
locally in each of serial_ns16550.c and serial_s3c24x0.c.
Add static directive to them and remove declarations from
include/common.h.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
The platform_data definitions are generally referenced from both
drivers and board files. That is why header files defining
platform_data sturectures are placed in "include" directory,
but our top level "include" directory is already too cluttered.
Let's collect platform_data definitions under the directory
"include/dm/platform_data" like Linux gathers ones around under
"include/linux/platform_data".
This commit moves two header files:
include/serial_mxc.h -> include/dm/platform_data/serial_mxc.h
include/serial_pl01x.h -> include/dm/platform_data/serial_pl01x.h
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Add driver model support to this driver, while retaining support for the
legacy system. Driver model serial support is enabled with CONFIG_DM_SERIAL
as usual.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Try to use this option to select the correct uart for the console. This
mimics the behaviour of drivers/serial.c.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
The probe logic sets up the pointer to the platform data in the device
tree decode method. It should be done in the probe() method, and anyway
the device tree decode method can't be used when CONFIG_OF_CONTROL is
not enabled.
Fix these two problems.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
It is inconvenient to have to use casts when specifying platform data. Also
it is not strictly correct, since we should use map_sysmem() to convert an
address to a pointer.
Adjust the platform data to use an address.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
There is a bug in the logic which checks for an available character. This
can cause invalid characters to be received - this was noticed on
beaglebone. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
We have moved the busy-wait loop out of drivers and into the uclass. This
means that we must reset the watchdog when busy-waiting.
Note: some drivers may still have a busy-wait even with driver model, as
a transition mechanism. Driver model will tolerate this, and is can be
cleaned up when all users of the driver use driver model. An example is
ns16550.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@ti.com>
Add driver model support in this driver, using platform data provided by
the board.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Adjust the driver so that leaf functions take a pointer to the serial port
register base. Put all the global configuration in the init function, and
use the same settings from then on.
This makes it much easier to move to driver model without duplicating the
code, since with driver model we use platform data rather than global
settings.
The driver is compiled with either the CONFIG_PL010_SERIAL or
CONFIG_PL011_SERIAL option and this determines the uart type. With driver
model this needs to come in from platform data, so create a new
CONFIG_PL01X_SERIAL config which brings in the driver, and adjust the
driver to support both peripheral variants.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@wwwdotorg.org>
Add driver model support with this driver. Boards which use this driver
should define platform data in their board files.
Signed-off-by: Simon Glass <sjg@chromium.org>
Avoid duplicating the code which deals with getc() and putc(). It is fairly
simple, but may expand later.
Signed-off-by: Simon Glass <sjg@chromium.org>
In some cases we really want to move forward with a deregister, add a force
parameter to allow this, and replace the dev with a nulldev in this case.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
This would be useful to start moving various config options.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Use driver model for serial ports.
Since Tegra now uses driver model for serial, adjust the definition of
V_NS16550_CLK so that it is clear that this is only used for SPL.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add driver model support so that ns16550 can support operation both with
and without driver model.
The driver needs a clock frequency so cannot stand alone unfortunately. The
clock frequency must be provided by a separate driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
The same sequence is used in several places, so move it into a function.
Note that UART_LCR_BKSE is an alias for UART_LCR_DLAB.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current sandbox serial driver is a pretty trivial example and does not
have the featues that might be needed for other board serial drivers. To
help provide a better example, add a text colour property to the device
tree for sandbox. This uses platform data, a device tree node, driver
private data and a remove() method.
Signed-off-by: Simon Glass <sjg@chromium.org>
Adjust the sandbox serial driver to use the new driver model uclass. The
driver works much as before, but within the new framework.
Signed-off-by: Simon Glass <sjg@chromium.org>
Serial devices support simple byte input/output and a few operations to find
out whether data is available. Add a basic uclass for serial devices to be
used by drivers that are converted to driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
The stdio_dev structure has a private pointer for its creator, but it is
not set up by the serial system. Set it to point to the serial device so
that it can be found by code called by stdio.
Signed-off-by: Simon Glass <sjg@chromium.org>
UART does not use the UART FIFO, but we should also not rely that
the UART FIFO is diabled by default. For instance, when loading
U-Boot using the boot ROMs serial downloader protocol over UART,
FIFO is enabled at U-Boot start time.
This patch disables the RX and TX FIFO, sets back their thresholds
and flushes them.
Signed-off-by: Stefan Agner <stefan@agner.ch>
The status register 1 (S1) is not writeable, hence we should not
write it. In order to clear the RDRF flag we only need to read
the data register.
Also, when stressing U-Boot a lot with serial input, an overflow can
occur which asserts the S1_OR flag (while not asserting the S1_RDRF
flag). To clear this flag we again just need to read the data
register, hence add this flag to the abort conditions for the while
loop.
Insert a compiler barrier to make sure reading the data register
gets executed after reading the status register.
Signed-off-by: Stefan Agner <stefan@agner.ch>
On vybrid, lpuart's registers are 8-bit. On LS102xA, lpuart's registers
are 32-bit. This patch adds the support for 32-bit registers on
LS102xA.
Signed-off-by: Jingchang Lu <jingchang.lu@freescale.com>
Signed-off-by: Yuan Yao <yao.yuan@freescale.com>
The nios2-yanu.h contains hardware registers and bits of
opencores yanu. As there is no other user of this header
, it should be moved into the driver.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
CC: Renato Andreola <renato.andreola@imagos.it>
The nios2-io.h defines hardware registers and bits of several FPGA
IP cores. It could be divided in to the specific drivers, including
altera timer, altera sysid, altera uart and altera jtag uart. The
altera pio and altera spi drivers use their own hardware definitions.
The removal of nios2-io.h will help modularity and maintenance.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
The following configs are not defined at all.
- CONFIG_OMAP1510
- CONFIG_OMAP_1510P1
- CONFIG_OMAP_SX1
- CONFIG_OMAP3_DMA
- CONFIG_OMAP3_ZOOM2
- CONFIG_OMAP_INNOVATOR
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
R8A7780 and R7A7791 of rmobile supports External Clock mode, and these uses
different from Internal Clock mode registers and calculations to the baud rate
setting. This adds function for External Clock mode.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
R8A7794 has DL and CKS register, and these registers are used in external clock
mode. This adds support these for R8A7794.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Use CONFIG_SOC_KEYSTONE in common places instead of defining
a lot of "if def .. || if def " for different Keystone2 SoC types.
Acked-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
For sandbox we have a fallback console which is used very early in
U-Boot, before serial drivers are available. Rather than try to guess
when to switch to the real console, add a flag so we can be sure. This
makes sure that sandbox can always output a panic() message, for example,
and avoids silent failure (which is very annoying in sandbox).
Signed-off-by: Simon Glass <sjg@chromium.org>
At present stdio device functions do not get any clue as to which stdio
device is being acted on. Some implementations go to great lengths to work
around this, such as defining a whole separate set of functions for each
possible device.
For driver model we need to associate a stdio_dev with a device. It doesn't
seem possible to continue with this work-around approach.
Instead, add a stdio_dev pointer to each of the stdio member functions.
Note: The serial drivers have the same problem, but it is not strictly
necessary to fix that to get driver model running. Also, if we convert
serial over to driver model the problem will go away.
Code size increases by 244 bytes for Thumb2 and 428 for PowerPC.
22: stdio: Pass device pointer to stdio methods
arm: (for 2/2 boards) all +244.0 bss -4.0 text +248.0
powerpc: (for 1/1 boards) all +428.0 text +428.0
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Just for type checking.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
The function still returns the same value.
The comment block is no longer necessary because our intention is
clear enough by using DIV_ROUND_CLOSEST() macro.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
If CONFIG_OMAP1610 is defined, the code returning the fixed value (26)
is enabled. But this case is covered by the following code.
(CONFIG_SYS_NS16550_CLK + (gd->baudrate * (MODE_X_DIV / 2))) /
(MODE_X_DIV * gd->baudrate)
= (48000000 + (115200 * (16 / 2))) / (16 * 115200)
= 48921600 / 1843200
= 26
The "#ifdef CONFIG_OMAP1610" was added by commit 6f21347d more than
ten years ago. In those days, the divide-and-round was not used.
I guess that is why this weird code was added here.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Rishi Bhattacharya <rishi@ti.com>
Bit 7 of UCR3 is described in the i.MX3x/i.MX5x/i.MX6x
reference manuals as follows:
Autobaud Detection Not Improved-. Disables new features of
autobaud detection (See Baud Rate Automatic Detection
Protocol, for more details).
0 Autobaud detection new features selected
1 Keep old autobaud detection mechanism
On at least i.MX6DQ, i.MX6DLS and i.MX53, the "new features"
occasionally cause the receiver to get out of sync and
continuously produce received characters of '\xff'.
This patch disables the "new feature" on all boards, since
there's no support for auto-baud in U-Boot on any of them.
More details are available in this post on i.MX Community:
https://community.freescale.com/message/403254
Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
keystone serial hw support hw flow control. This patch
enables hw flow control for keystone EVMs as an optional
feature based on CONFIG_SERIAL_HW_FLOW_CONTROL.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
gd->bd->bi_baudrate is a copy of gd->baudrate.
Since baudrate is a common feature for all architectures,
keep gd->baudrate only.
It is true that bi_baudrate was passed to the kernel in that structure
but it was a long time ago.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Tom Rini <trini@ti.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu> (For microblaze)
's/zynq_serial_initalize/zynq_serial_initialize/g'
serial_initialize is used by all serial drivers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Warnings:
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:181:1: warning: symbol 'uart_zynq0_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:182:22: warning: symbol 'uart_zynq_serial0_device' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_init' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_setbrg' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_getc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_tstc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_putc' was not declared. Should it be static?
drivers/serial/serial_zynq.c:184:1: warning: symbol 'uart_zynq1_puts' was not declared. Should it be static?
drivers/serial/serial_zynq.c:185:22: warning: symbol 'uart_zynq_serial1_device' was not declared. Should it be static?
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
k2hk EVM is based on Texas Instruments Keystone2 Hawking/Kepler
SoC. Keystone2 SoC has ARM v7 Cortex-A15 MPCore processor. Please
refer the ti/k2hk_evm/README for details on the board, build and other
information.
This patch add support for keystone architecture and k2hk evm.
Signed-off-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: WingMan Kwok <w-kwok2@ti.com>
Signed-off-by: Sandeep Nair <sandeep_n@ti.com>
It is useful for Cltl-C to be handled by U-Boot as it is on other boards.
But it is also useful to be able to terminate U-Boot with Ctrl-C.
Add an option to enable signals while in raw mode, and make this the
default. Add an option to leave the terminal cooked, which is useful for
redirecting output.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a simple LCD driver which uses SDL to display the image. We update the
image regularly, while still providing for reasonable performance.
Adjust the common lcd code to support sandbox.
For command-line runs we do not want the LCD to be displayed, so add a
--show_lcd option to enable it.
Tested-by: Che-Liang Chiou <clchiou@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
This is required for proper functionality on big-endian targets.
Memory-mapped registres of ARC UART are not 32-bit words but 8-bit bytes
so on little-endian target either acessor (_l or _b) works fine.
On big-endian only _b accessors works as expected.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Noam Camus <noamc@ezchip.com>
Cc: Tom Rini <trini@ti.com>
Remove hard coded frequencies and use Zynq's clock framework to obtain
the UART clock frequency.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define both serial uarts in the driver and return
default uart based on board configuration.
- Move baseaddresses to hardware.h
- Define default baudrate and clock values
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The implementation of oc_serial_setbrg() for CONFIG_SYS_NIOS_FIXEDBAUD and
!CONFIG_SYS_NIOS_FIXEDBAUD are very similar.
Add a baudrate variable and set it to either CONFIG_BAUDRATE or gd->baudrate.
Then we can unify the code for both cases.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Fix build error due to missing include of serial.h and a trivial typo.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Driver for non-standard on-chip UART, instantiated in the ARC (Synopsys)
FPGA Boards such as ARCAngel4/ML50x
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Cc: Mischa Jonker <mjonker@synopsys.com>
Cc: Francois Bedard <fbedard@synopsys.com>
Cc: Tom Rini <trini@ti.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
The mv_udc is not marvell-specific anymore. The mv_udc is used to drive
generic ChipIdea CI13xxx series OTG cores, so rename the driver to ci_udc
instead.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Stefano Babic <sbabic@denx.de>
This driver is no longer used, remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Michael Schwingen <michael@schwingen.org>
Cc: Tom Rini <trini@ti.com>
This patch fix the u-boot shell problem on TRATS2 board.
- If hold the key while booting is in progress,
white spaces are written in u-boot shell.
Set Automatically clears after resetting Rx FIFO.
Signed-off-by: Inha Song <ideal.song@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Bringing in the MMC tree means that CONFIG_BOUNCE_BUFFER needed to be
added to include/configs/exynos5-dt.h now.
Conflicts:
include/configs/exynos5250-dt.h
Signed-off-by: Tom Rini <trini@ti.com>
The omap3_zoom2 board has not been updated for a correct CONFIG_SYS_HZ
and Tom Rix's email has long been bouncing.
Signed-off-by: Tom Rini <trini@ti.com>
For LPC32XX high-speed UART it is required to send a carriage return
symbol along with line feed. The problem was introduced in e503f90a
commit.
Signed-off-by: Vladimir Zapolskiy <vz@mleia.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Staticize local functions in xuartlite driver.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Tested-by: Michal Simek <monstr@monstr.eu>
This adds the preset value to register, and setup of baudrate.
Signed-off-by: Kouei Abe <kouei.abe.cp@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
The former SH/SCIF driver had calculated baudrate based on CONFIG_SYS_CLK_FREQ.
The newest SH/SCIF needs calculation of the clock for SCIF.
This patch defines clock CONFIG_SH_SCIF_CLK_FREQ for SCIF and changes it to
CONFIG_SH_SCIF_CLK_FREQ from CONFIG_SYS_CLK_FREQ.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
CC: Albert Aribaud <albert.u.boot@aribaud.net>
Since commit 5dc5f36 removed B2 board support,
there are no boards enabling serial_s3c44b0.
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Andrea Scian <andrea.scian@dave-tech.it>
The driver makes it possible to use an application UART as
the U-Boot output console for Freescale i.MX23/i.MX28 devices.
Signed-off-by: Andreas Wass <andreas.wass@dalelven.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Use default_serial_puts() instead of its own implementation.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <monstr@monstr.eu>
Fixup an easy conflict over adding the clk_get prototype and USB_OTG
defines for am33xx having moved.
Conflicts:
arch/arm/include/asm/arch-am33xx/hardware.h
Signed-off-by: Tom Rini <trini@ti.com>
Rename some CONFIG_TI814X to a more generic CONFIG_TI81XX
Signed-off-by: Antoine Tenart <atenart@adeneo-embedded.com>
[trini: Adapt for CONFIG_OMAP_COMMON changes, AM43XX]
Signed-off-by: Tom Rini <trini@ti.com>
Register arm_dcc with drivers/serial/serial.c
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Removed stdio structure ops support on arm_dcc
driver, and need to register with serial core
so-that it can access like remianing serial drivers.
Signed-off-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The mv_udc driver is broken for a while and doesn't even compile.
This patch fixes the issues and gets the driver into working state
again. This driver was tested on Freescale i.MX233/i.MX28 .
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Lei Wen <leiwen@marvell.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
Fix a trivial conflict in arch/arm/dts/exynos5250.dtsi about gpio and
serial.
Conflicts:
arch/arm/dts/exynos5250.dtsi
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds FDT support to the serial s5p driver.
At present disabling the serial console (from the device tree) crashes
U-Boot. Add checks for this case, so that execution can continue without
a serial console.
It also enables the serial_s5p driver recognize the silent_console option.
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Gabe Black <gabeblack@google.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Rajeshwari Shinde <rajeshwari.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The omap2420H4 was the only mainline omap24xx board. Prior to being
fixed by Jon Hunter in time for v2013.04 it had been functionally broken
for a very long time. Remove this board as there's not been interest in
it in U-Boot for quite a long time.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds lpuart support for Vybrid VF610 platform.
Signed-off-by: TsiChung Liew <tsicliew@gmail.com>
Signed-off-by: Alison Wang <b18965@freescale.com>
This patch enables the uart tx/rx fifo. Now that fifo is enabled,
the uart read/write functions are modfied to check the UFSTAT register
for fifo status instead of UTRSTAT (as required with fifo's enabled).
Tested by booting linux kernel. Before enabling tx/rx fifo
"Uncompressing linux" message is garbled and after enabling it is proper.
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Akshay Saraswat <akshay.s@samsung.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Freescale MPC8220 Power Architecture processors have long reached
EOL; Freescale does not even list these any more on their web site.
Remove the code to avoid wasting maitaining efforts on dead stuff.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Andy Fleming <afleming@gmail.com>
- Move blackfin serial driver to the generic driver folder.
- Move blackfin serial headers to blackfin arch head folder.
- Update the include path to blackfin serial header in start up code.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Following the removal of the smdk6400 board, the s3c64xx SoC becomes unused, so
remove associated code. It will still be possible to restore it later from the
Git history if necessary.
Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Flush UART3 xmit on enable if TEMT is broken
On some OMAP3 devices when UART3 is configured for boot mode before SPL starts
only THRE bit is set. We have to empty the transmitter before initialization
starts. This patch avoids the use of CONFIG_SYS_NS16550_BROKEN_TEMT.
Signed-off-by: Manfred Huber <man.huber@arcor.de>
Tested-by: Javier Martinez Canillas <javier@dowhile0.org>
Tested-by: Andreas Bießmann <andreas.devel@googlemail.com>
'bool' is defined in random places. This patch consolidates them into a
single header file include/linux/types.h, using stdbool.h introduced in C99.
All other #define, typedef and enum are removed. They are all consistent with
true = 1, false = 0.
Replace FALSE, False with false. Replace TRUE, True with true.
Skip *.py, *.php, lib/* files.
Signed-off-by: York Sun <yorksun@freescale.com>
Albert's rework of the linker scripts conflicted with Simon's making
everyone use __bss_end. We also had a minor conflict over
README.scrapyard being added to in mainline and enhanced in
u-boot-arm/master with proper formatting.
Conflicts:
arch/arm/cpu/ixp/u-boot.lds
arch/arm/cpu/u-boot.lds
arch/arm/lib/Makefile
board/actux1/u-boot.lds
board/actux2/u-boot.lds
board/actux3/u-boot.lds
board/dvlhost/u-boot.lds
board/freescale/mx31ads/u-boot.lds
doc/README.scrapyard
include/configs/tegra-common.h
Build tested for all of ARM and run-time tested on am335x_evm.
Signed-off-by: Tom Rini <trini@ti.com>
This cast does not seem correct, since we should be writing to a pointer,
not a ulong.
This fixes the following warning on nds32:
-ns16550.c:49: warning: passing argument 2 of 'writeb' makes pointer from integer without a cast
Signed-off-by: Simon Glass <sjg@chromium.org>
In master we had already taken a patch to fix the davinci GPIO code for
CONFIG_SOC_DM646X and in u-boot-ti we have additional patches to support
DA830 (which is CONFIG_SOC_DA8XX && !CONFIG_SOC_DA850). Resolve these
conflicts manually and comment the #else/#endif lines for clarity.
Conflicts:
arch/arm/include/asm/arch-davinci/gpio.h
drivers/gpio/da8xx_gpio.c
Signed-off-by: Tom Rini <trini@ti.com>
Implements the tstc() interface for the serial driver. Multiplexing
the console between the serial port and a keyboard uses a polling
method of checking if characters are available; this means that the
serial console must be non-blocking when attempting to read
characters.
Signed-off-by: Taylor Hutt <thutt@chromium.org>
Signed-off-by: Simon Glass <sjg@chromium.org>
Commit 8b710b1 started removing code for the unmaintained "ns9750dev"
board; the board support is still broken, and not included anywhere in
the Makefile or boards.cfg. Remove the remaining dead code.
Signed-off-by: Wolfgang Denk <wd@denx.de>
CONFIG_ARM_DCC_MULTI should be also removed in the patch
"serial: Remove CONFIG_SERIAL_MULTI from serial drivers"
(sha1: a382725060)
Because the driver defines serial_* functions
which cause conflict with serial.c (multiple definition of serial_*)
Removing CONFIG_SERIAL_MULTI function also require to define
default_serial_console for cases where another serial driver
is not available in the system.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Marek Vasut <marex@denx.de>
Some platforms (e.g. IGEPv2 board) has a broken ns16550 UART that
does not set the TEMT bit when the transmitter is empty in SPL.
This makes U-Boot to hang while waiting for TEMT to be set.
Add a new option to avoid this:
CONFIG_SYS_NS16550_BROKEN_TEMT
16550 UART set the Transmitter Empty (TEMT) Bit when all output
has finished and the transmitter is totally empty. U-Boot waits
for this bit to be set to initialize the serial console. On some
broken platforms this bit is not set in SPL making U-Boot to
hang while waiting for TEMT. Define this option to avoid it.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
If the pl011 is connected to another device which has hardware
flow-control on, characters are never received by the pl011.
Asserting RTS when flow-control is off will have no effect.
This is in line with how Linux behaves.
Signed-off-by: Joshua Housh <joshua.housh@calxeda.com>
Tested-by: Marek Vasut <marex@denx.de>
On kzm9g board (rmobile SoC), autoboot fails if serial console cable is not
connected. When serial cable is not connected, serial error occurs and
some garbage comes in data register.
sh_serial_tstc() in serial_sh.c does not check error status and misunderstand
there is some input data. It is the reason that autoboot fails.
This patch adds checking error status in sh_serial_tstc().
This patch is based on v2013.01-rc1 tag of u-boot master git.
Signed-off-by: Tetsuyuki Kobayashi <koba@kmckk.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
TEMT is set when the transmitter is totally empty and all output has
finished.
This prevents output problems (including a loss of synchronization
observed on p2020 that persisted for quite a while) if SPL has output
still on its way out.
Signed-off-by: Scott Wood <scottwood@freescale.com>
--
v2: fixed typo in subject, and explained what the bit does in the changelog
CONFIG_NS16550_MIN_FUNCTIONS is used by small SPLs to gain access to basic
ns16550 output code without pulling in things not needed by the SPL.
This previously only worked with non-MULTI configs. Recently MULTI was
made mandatory, and MIN_FUNCTIONS fails like this:
drivers/serial/libserial.o: In function `calc_divisor.clone.0':
serial_ns16550.c:(.text.calc_divisor.clone.0+0x24): undefined reference to `get_bus_freq'
drivers/serial/libserial.o: In function `_serial_getc':
(.text._serial_getc+0x30): undefined reference to `NS16550_getc'
drivers/serial/libserial.o: In function `_serial_tstc':
(.text._serial_tstc+0x30): undefined reference to `NS16550_tstc'
drivers/serial/libserial.o: In function `_serial_setbrg':
(.text._serial_setbrg+0x3c): undefined reference to `NS16550_reinit'
make[1]: *** [/tmp/u-boot/spl/u-boot-spl] Error 1
make: *** [/tmp/u-boot/spl/u-boot-spl.bin] Error 2
With MIN_FUNCTIONS we don't need anything from this file, so don't build
it. The conditional needs to be in the file itself rather than the
makefile, because the config symbols are only imported to the makefiles
once, not separately for the SPL phase of the build.
Signed-off-by: Scott Wood <scottwood@freescale.com>
This patch is fixing the following errors
s3c64xx.c:175: error: variable 's3c64xx_serial_drv' has initializer but incomplete type
s3c64xx.c:176: error: unknown field 'name' specified in initializer
s3c64xx.c:176: warning: excess elements in struct initializer
s3c64xx.c:176: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:177: error: unknown field 'start' specified in initializer
s3c64xx.c:177: warning: excess elements in struct initializer
s3c64xx.c:177: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:178: error: unknown field 'stop' specified in initializer
s3c64xx.c:178: warning: excess elements in struct initializer
s3c64xx.c:178: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:179: error: unknown field 'setbrg' specified in initializer
s3c64xx.c:179: warning: excess elements in struct initializer
s3c64xx.c:179: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:180: error: unknown field 'putc' specified in initializer
s3c64xx.c:180: warning: excess elements in struct initializer
s3c64xx.c:180: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:181: error: unknown field 'puts' specified in initializer
s3c64xx.c:181: warning: excess elements in struct initializer
s3c64xx.c:181: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:182: error: unknown field 'getc' specified in initializer
s3c64xx.c:182: warning: excess elements in struct initializer
s3c64xx.c:182: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c:183: error: unknown field 'tstc' specified in initializer
s3c64xx.c:183: warning: excess elements in struct initializer
s3c64xx.c:183: warning: (near initialization for 's3c64xx_serial_drv')
s3c64xx.c: In function 's3c64xx_serial_initialize':
s3c64xx.c:188: warning: implicit declaration of function 'serial_register'
s3c64xx.c: At top level:
s3c64xx.c:191: error: expected '=', ',', ';', 'asm' or '__attribute__' before 'struct'
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
Acked-by: Marek Vasut <marex@denx.de>
u-boot's byteorder headers did not contain endianness attributions
for use with sparse, causing a lot of false positives. Import the
kernel's latest definitions, and enable them by including compiler.h
and types.h. They come with 'const' added for some swab functions, so
fix those up, too:
include/linux/byteorder/big_endian.h:46:2: warning: passing argument 1 of '__swab64p' discards 'const' qualifier from pointer target type [enabled by default]
Also, note: u-boot's historic __BYTE_ORDER definition has been
preserved (for the time being at least).
We also remove ad-hoc barrier() definitions, since we're including
compiler.h in files that hadn't in the past:
macb.c:54:0: warning: "barrier" redefined [enabled by default]
In addition, including compiler.h in byteorder changes the 'noinline'
definition to expand to __attribute__((noinline)). This fixes
arch/powerpc/lib/bootm.c:
bootm.c:329:16: error: attribute '__attribute__': unknown attribute
bootm.c:329:16: error: expected ')' before '__attribute__'
bootm.c:329:25: error: expected identifier or '(' before ')' token
powerpc sparse builds yield:
include/common.h:356:22: error: marked inline, but without a definition
the unknown-reason inlining without a definition is considered obsolete
given it was part of the 2002 initial commit, and no arm version was
'fixed.'
also fixed:
ydirectenv.h:60:0: warning: "inline" redefined [enabled by default]
and:
Configuring for devconcenter - Board: intip, Options: DEVCONCENTER
make[1]: *** [4xx_ibm_ddr2_autocalib.o] Error 1
make: *** [arch/powerpc/cpu/ppc4xx/libppc4xx.o] Error 2
powerpc-fsl-linux-size: './u-boot': No such file
4xx_ibm_ddr2_autocalib.c: In function 'DQS_autocalibration':
include/asm/ppc4xx-sdram.h:1407:13: sorry, unimplemented: inlining failed in call to 'ppc4xx_ibm_ddr2_register_dump': function body not available
4xx_ibm_ddr2_autocalib.c:1243:32: sorry, unimplemented: called from here
and:
In file included from crc32.c:50:0:
crc32table.h:4:1: warning: implicit declaration of function '___constant_swab32' [-Wimplicit-function-declaration]
crc32table.h:4:1: error: initializer element is not constant
crc32table.h:4:1: error: (near initialization for 'crc32table_le[0]')
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
[trini: Remove '#endif' in include/common.h around setenv portion]
Signed-off-by: Tom Rini <trini@ti.com>
serial_ns16550.c:222:1: warning: symbol 'eserial1_init' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_setbrg' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_getc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_tstc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_putc' was not declared. Should it be static?
serial_ns16550.c:222:1: warning: symbol 'eserial1_puts' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_init' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_setbrg' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_getc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_tstc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_putc' was not declared. Should it be static?
serial_ns16550.c:225:1: warning: symbol 'eserial2_puts' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_init' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_setbrg' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_getc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_tstc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_putc' was not declared. Should it be static?
serial_ns16550.c:228:1: warning: symbol 'eserial3_puts' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_init' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_setbrg' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_getc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_tstc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_putc' was not declared. Should it be static?
serial_ns16550.c:231:1: warning: symbol 'eserial4_puts' was not declared. Should it be static?
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The following commit introduces some build failures for ColdFire
platform.
commit abaef69fbe
Author: Marek Vasut <marex@denx.de>
Date: Thu Sep 13 16:51:38 2012 +0200
Add the missed header files.
Sign-off-by: Alison Wang <b18965@freescale.com>
Add kerneldoc annotations into serial core.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Reorder the get_current() function to make it a bit more readable.
The code does not grow and there is minor change in the code logic,
where dev != NULL is now checked in any case.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Reorder serial_assign() function to get rid of the extra level of
indentation. Also, adjust the return value to be -EINVAL instead of
positive one to be more consistent.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Replace the in-place ad-hoc implementation of serial_puts() within
the drivers with default_serial_puts() call. This cuts down on the
code duplication quite a bit.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
U-Boot contains a lot of duplicit implementations of serial_puts()
call which just pipes single characters into the port in loop. Implement
function that does this behavior into common code, so others can make
easy use of it.
This function is called default_serial_puts() and it's sole purpose
is to call putc() in loop on the whole string passed to it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Since commit 957731ed (ARM: remove broken "lpd7a40x" boards),
lh7a40x cpu and serial driver have become unused. Remove them.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Enhance the manual relocation of drivers operations structure by
checking if the entries are NULL and increment them only if they
are not. This allows for setting any entry to NULL and it will
survive the manual relocation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Compile drivers/serial/serial.c by default both into SPL and into
non-SPL builds, since CONFIG_SERIAL_MULTI is now the default state.
Also having common/serial.c in by default now, it's pointless to keep
-DCONFIG_SERIAL_MULTI in CPPFLAGS any longer, so remove it as well.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Remove the support for not-CONFIG_SERIAL_MULTI part from serial
port drivers and some board files. Since CONFIG_SERIAL_MULTI is
now enabled by default, that part is a dead code. Remove it.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Anatolij Gustschin <agust@denx.de>
Cc: Stefan Roese <sr@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Enable CONFIG_SERIAL_MULTI for all builds of U-Boot. That includes
both SPL builds and non-SPL builds, everything. To avoid poluting
this patch with removal of ifdef-endif constructions containing
CONFIG_SERIAL_MULTI, the CONFIG_SERIAL_MULTI is temporarily added
into CPPFLAGS in config.mk . This will be again removed in following
patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
Move the common/serial.c into driver/serial/, since this file
provides serial multiplexing functions and it is imperative to
be linked with libserial.o instead of libcommon.o.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Tom Rini <trini@ti.com>
