Add reference to Avanta Boot Flow documentation, BobCat2, AlleyCat3 and
PONCat3 BootROM Firmware documentation and links to public Marvell tools:
hdrparser.c and doimage.c
Signed-off-by: Pali Rohár <pali@kernel.org>
Marvell BootROM loads MMC image from sector 0 (HW boot or data partition)
and SD image from sector 1.
So for SD card booting it is needed to not use constant CONFIG MMC options
and instead of them it is needed to define functions spl_mmc_boot_mode()
spl_mmc_get_uboot_raw_sector() which determinate offsets at SPL runtime
based on MMC or SD card.
Calculation of SD card sector expects following values:
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_DATA_PART_OFFSET=0
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Pali Rohár <pali@kernel.org>
On some platforms is SYS_MMCSD_FS_BOOT_PARTITION unsupported. So allow to
completely disable MMC FS Boot support via new option SYS_MMCSD_FS_BOOT.
By default MMC FS Boot support is enabled (like it was before) except for
ARCH_MVEBU where MMC FS Boot supported is unsupported due to Marvell
BootROM limitations.
Signed-off-by: Pali Rohár <pali@kernel.org>
When eMMC boot is selected then BootROM loads kwbimage header (U-Boot SPL)
from the selected eMMC boot partition. So for eMMC boot ensure that U-Boot
SPL loads U-Boot proper (from kwbimage) also from the same selected eMMC
boot partition.
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Pali Rohár <pali@kernel.org>
BOOT_DEVICE_MMC2 and BOOT_DEVICE_MMC2_2 are representing mmc dev 1 but all
Armada SoCs have only one mmc controller. So remove references to
non-existent second mmc controller.
Fixes: f830703f42 ("arm: mvebu: Check that kwbimage blockid matches boot mode")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
Reject invalid and accept valid SATA images.
Fixes: 5a06534933 ("cmd: mvebu/bubt: Check for A38x image data checksum")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
To process SATA kwbimage and load U-Boot proper from it in the same way as
Marvell BootROM, it is needed to interpret srcaddr as relative offset to
the main header. This change fixes booting of U-Boot proper from SPL code
in SATA image.
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
To parse SATA kwbimage in the same way as Marvell BootROM, it is needed to
interpret srcaddr as relative offset to the main header. This change fixes
loading of SATA images via kwboot over UART.
Fixes: 792e423550 ("tools: kwboot: Patch source address in image header")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SATA image as number of sectors the beginning of the hard
drive, but as number of sectors relative to the main header.
The main header is stored at absolute sector number 1. So do not add or
subtract it when calculating with relative offsets to the main header.
Fixes: 501a54a29c ("tools: kwbimage: Fix generation of SATA, SDIO and PCIe images")
Fixes: 5c61710c98 ("tools: kwbimage: Properly set srcaddr in kwbimage v0")
Fixes: e0c243c398 ("tools: kwbimage: Validate data checksum of v1 images")
Fixes: aa6943ca31 ("kwbimage: Add support for extracting images via dumpimage tool")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To ensure that we do not store invalid SDIO image to the boot location
(read by the Marvell BootROM), we need to check that image is valid
and srcaddr is intepreted in bytes, in the same way as it is done by
Marvell BootROM.
This fixes rejecting valid and accepting invalid SDIO images by bubt command.
Fixes: 5a06534933 ("cmd: mvebu/bubt: Check for A38x image data checksum")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To process SDIO kwbimage and load U-Boot proper from it in the same way as
Marvell BootROM, it is needed to interpret srcaddr in bytes. This change
fixes booting of U-Boot proper from SPL code stored in SDIO image.
Fixes: 2226ca1734 ("arm: mvebu: Load U-Boot proper binary in SPL code based on kwbimage header")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To parse SDIO kwbimage in the same way as Marvell BootROM, it is needed to
interpret srcaddr in bytes. This change fixes loading of SDIO images via
kwboot over UART.
Fixes: 792e423550 ("tools: kwboot: Patch source address in image header")
Signed-off-by: Pali Rohár <pali@kernel.org>
Despite the official specification, Marvell BootROM does not interpret
srcaddr from SDIO image as offset in number of sectors (like for SATA
image), but as offset in bytes (like for all other images except SATA).
To generate SDIO kwbimage compatible with Marvell BootROM, it is needed to
have srcaddr in bytes. This change fixes SDIO images for Armada 38x SoCs.
Fixes: 501a54a29c ("tools: kwbimage: Fix generation of SATA, SDIO and PCIe images")
Fixes: 5c61710c98 ("tools: kwbimage: Properly set srcaddr in kwbimage v0")
Fixes: e0c243c398 ("tools: kwbimage: Validate data checksum of v1 images")
Fixes: aa6943ca31 ("kwbimage: Add support for extracting images via dumpimage tool")
Signed-off-by: Pali Rohár <pali@kernel.org>
Please pull the updates for rockchip platform:
- Add support for rk3588 soc;
- Add rk3588 Edgeble Neu6 board and Radxa ROCK5B board;
- Add rk3308 Radxa ROCK Pi S board;
- Add rk3568 Radxa ROCK 3 board,
- Add rk3566 Radxa Compute Module 3 board;
- Add support for sdram reg info version 3
- Refactor rockchip OTP/eFuse driver and add more soc support;
- Add external TPL support for binman;
binman support for mkimage ignore missing entry is based on [1];
[1] https://patchwork.ozlabs.org/project/uboot/patch/20230219220158.4160763-7-jonas@kwiboo.se/
-----BEGIN PGP SIGNATURE-----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=6a0G
-----END PGP SIGNATURE-----
Merge tag 'tpm-next-28022023' of https://source.denx.de/u-boot/custodians/u-boot-tpm into next
TPM auto startup and testing:
Due to U-Boot's lazy binding we always relied on command line tools to
initialize the TPM subsystem and devices. One exception is the EFI
subsystem. When compiled with TCG2 measured boot support the TPM was
automatically initialized.
However that init was not complete. The TCG specs [0] (and specifically
§12.3 Self-test modes) describe how self-tests on the device should be
performed. This PR is adding an extra API function, that can be used to
initialize the TPM2.0 properly.
Simon added the equivalent for TPM1.2 and refactored the DM tests to
include the new funtion.
[0] https://trustedcomputinggroup.org/wp-content/uploads/TPM-Rev-2.0-Part-1-Architecture-01.07-2014-03-13.pdf
- mark reserved blocks from Ashok Reddy Soma
- backport BRCMNAND changes from Linux from Linus Walleij
- fix display of unknown raw ID from Patrice Chotard
- show reserved block in chip.erase from Michael Trimarchi
-----BEGIN PGP SIGNATURE-----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=0HB0
-----END PGP SIGNATURE-----
Merge tag 'u-boot-nand-20230227' of https://source.denx.de/u-boot/custodians/u-boot-nand-flash into next
Pull request for u-boot-nand-20230227
- mark reserved blocks from Ashok Reddy Soma
- backport BRCMNAND changes from Linux from Linus Walleij
- fix display of unknown raw ID from Patrice Chotard
- show reserved block in chip.erase from Michael Trimarchi
RK3588 has two memory gaps when using 16 GiB DRAM size:
[0x3fc000000 , 0x3fc500000]
and
[0x3fff00000 , 0x3ffffffff]
If the kernel is agnostic to these gaps, accessing the area causes
a SError panic.
Hence, add reserved memory areas in kernel's DTB before booting.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
ROCK 5B is a Rockchip RK3588 based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specification:
Rockchip Rk3588 SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x HDMI output, 1x HDMI input
Ethernet port
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 54mm
Kernel commits:
a1d3281450ab ("arm64: dts: rockchip: Add rock-5b board")
6fb13f888f2a ("arm64: dts: rockchip: Update sdhci alias for rock-5b")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
SDHCI driver may attempt to set 26MHz clock, but clk_rk3568
will return error in this case. Apparently, SDHCI silently ignores the
error and as a result eMMC initialization fails.
Add 25 MHz and 26 MHz clk rates for sdmmc and emmc on rk3568 to fix that.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The cpuid on RK3568 is located at 0xa instead of 0x7 as all other SoCs.
Add and use a CFG_CPUID_OFFSET to define this offset.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Set eth1addr in addition to ethaddr.
Also allow fdt fixup of ethernet mac addresses when CMD_NET is disabled.
Set ethaddr and eth1addr based on HASH and SHA256 options.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for rk3066a, rk3188, rk322x and rk3288 compatible.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor the driver to use driver data and ops to simplify handling
of SoCs that require a unique read op.
Move handling of the aligned bounce buffer to main read op in order to
keep the SoC unique read op simple.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a simple debug command to dump the content of the otp.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for rk3588 compatible.
Adjust offset using driver data in main read op.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for rk3568 compatible.
Handle allocation of an aligned bounce buffer in main read op in order
to keep the SoC unique read op simple.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Refactor the driver to use driver data and ops to simplify handling
of SoCs that require a unique read op.
Use readl_poll_sleep_timeout instead of a custom poll loop, and add
validation of input parameter to main read op.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
Boot log for the record,
DDR Version V1.08 20220617
LPDDR4X, 2112MHz
channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS1 Row=16 CS=2 Die BW=16 Size=2048MB
Manufacturer ID:0x6
CH0 RX Vref:31.7%, TX Vref:21.8%,21.8%
CH1 RX Vref:30.7%, TX Vref:22.8%,23.8%
CH2 RX Vref:30.7%, TX Vref:22.8%,22.8%
CH3 RX Vref:30.7%, TX Vref:21.8%,21.8%
change to F1: 528MHz
change to F2: 1068MHz
change to F3: 1560MHz
change to F0: 2112MHz
out
U-Boot SPL 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Trying to boot from MMC1
INFO: Preloader serial: 2
NOTICE: BL31: v2.3():v2.3-391-g856309329:derrick.huang
NOTICE: BL31: Built : 14:15:50, Jul 18 2022
INFO: ext 32k is not valid
INFO: GICv3 without legacy support detected.
INFO: ARM GICv3 driver initialized in EL3
INFO: system boots from cpu-hwid-0
INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
INFO: dfs DDR fsp_params[0].freq_mhz= 2112MHz
INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
INFO: BL31: Initialising Exception Handling Framework
INFO: BL31: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader, Booting device without OPTEE initialization. SMC`s destined for OPTEE will return SMC_UNK
ERROR: Error initializing runtime service opteed_fast
INFO: BL31: Preparing for EL3 exit to normal world
INFO: Entry point address = 0xa00000
INFO: SPSR = 0x3c9
U-Boot 2023.01-00952-g1d1785a516-dirty (Jan 30 2023 - 19:53:55 +0530)
Model: Edgeble Neu6A IO Board
DRAM: 7.5 GiB (effective 3.7 GiB)
Core: 71 devices, 15 uclasses, devicetree: separate
MMC: mmc@fe2c0000: 0
Loading Environment from nowhere... OK
In: serial@feb50000
Out: serial@feb50000
Err: serial@feb50000
Model: Edgeble Neu6A IO Board
Net: No ethernet found.
Hit any key to stop autoboot: 0
=>
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Booting from SDMMC is one of the fast and easy booting methods
for initial support of any SoC to upstream more features.
This patch is trying to add the sdmmc node for rk3588 and added
as u-boot specific node in -u-boot.dtsi as upstream Linux is not
supporting yet.
As soon as Linux supports it, a sync of the Linux device tree
would eventually drop this node.
Clock properties as added according to the rockchip mmc driver
but the actual definition might add scmi clocks into 0 and 1
indexes. This is due to scmi clock are not supporting in upstream
U-Boot. Properly addition of scmi clock would eventually follow
sdmmc clock definition of Linux once they upstreamed.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Add u-boot,dm-spl and u-boot,dm-pre-reloc related properties
for Rockchip RK3588 SoC to boot the SPL.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Rockchip RK3588 is a ARM-based SoC with quad-core Cortex-A76
and quad-core Cortex-A55 including NEON and GPU, 6TOPS NPU,
Mali-G610 MP4, HDMI Out, HDMI In, DP, eDP, MIPI DSI, MIPI CSI2,
LPDDR4/4X/5, eMMC5.1, SD3.0/MMC4.5, USB OTG 3.0, Type-C, USB 2.0,
PCIe 3.0, SATA 3, Ethernet, SDIO3.0 I2C, UART, SPI, GPIO and PWM.
Add arch core support for it.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu6) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
IO board offers plenty of peripherals and connectivity options and
this patch enables basic eMMC and UART which is enough to successfully
boot Linux.
Neu6 needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6(Neu6) IO platform.
commit <a5079a534554> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A IO")
Add support for Edgeble Neu6 Model A IO Board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6(Neu2) is a 96boards SoM-CB compute module
based on Rockchip RK3588 from Edgeble AI.
General features:
- Rockchip RK3588
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
On module WiFi6/BT5 is available in the following Neu6 variants.
Neu6 needs to mount on top of associated Edgeble IO boards for
creating complete platform solutions.
Enable eMMC for now to boot Linux successfully.
commit <3d9a2f7e7c5e> ("arm64: dts: rockchip: rk3588: Add Edgeble Neu6
Model A SoM")
Add support for Edgeble Neu6 Model A SoM.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
This initial version supports CPU, dma, interrupts, timers, UART and
SDHCI (everything necessary to boot Linux on this system on chip) as
well as Ethernet, I2C, PWM and SPI.
The DT is split into rk3588 and rk3588s, which is a reduced version
(i.e. with less peripherals) of the former.
commit <9fb232e9911f> (" arm64: dts: rockchip: Add base DT for rk3588
SoC")
commit <d68a97d501f8> ("arm64: dts: rockchip: Add rk3588 pinctrl data")
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add IOC unit header include for rk3588.
Signed-off-by: Steven Liu <steven.liu@rock-chips.com>
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add ddr driver for rk3588 to get the ram capacity.
Co-developed-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add RK3588 pll set and get rate clock support.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock driver support for Rockchip RK3588 SoC.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add the dt-bindings header for the Rockchip RK3588, that gets
shared between the clock controller and the clock references
in the dts.
commit <f204a60e545c> ("dt-bindings: clock: add rk3588 clock
definitions")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add clock and reset unit header include for rk3588.
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for rk3588 package header in mkimage tool.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update the MAINTAINERS file to include the devicetree for the
rk3568-evb1-v10 board.
Also update Rockchip board docs to include information on building
RK3568 based devices.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add gpio-ranges property to GPIO nodes so that the bank ID can
be correctly derived for each GPIO bank.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
