Use CONFIG_SYS_PCI*_IO_BUS for the bus relative address instead
of _IO_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Use CONFIG_SYS_{PCI,RIO}_MEM_BUS for the bus relative address instead
of _MEM_BASE so we are more explicit.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Added a CONFIG_SYS_FLASH_BASE_PHYS for use as the physical address and
maintain CONFIG_SYS_FLASH_BASE as the virtual address of the flash.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
Added a PIXIS_BASE_PHYS for use as the physical address and maintain
PIXIS_BASE as the virtual address of the PIXIS fpga registers.
This allows us to deal with 36-bit phys on these boards in the future.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Acked-by: Andy Fleming <afleming@freescale.com>
- Move the TLB entry of PIXIS_BASE from TLB0 to TLB1[8], because in CAMP mode,
all the TLB0 entries will be invalidated after cpu1 brings up kernel, thus cpu0
can not access PIXIS_BASE anymore (any access will cause DataTLBError exception)
- Set CONFIG_SYS_DDR_TLB_START to 9 for MPC8572DS board.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
PCIE2 and PCIE3 should be decided by corresponing bit in devdisr instead of
PCIE1 bit.
On MPC8572DS board, PCIE refers to PCIE1.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The IO port selection is not correct on MPC8572DS and MPC8544DS board.
This patch fixes this issue.
For MPC8572
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x7, 0xb, 0xc, 0xf
PCIE2 0x3, 0x7
PCIE3 0x7
For MPC8544
Port cfg_io_ports
PCIE1 0x2, 0x3, 0x4, 0x5, 0x6, 0x7
PCIE2 0x4, 0x5, 0x6, 0x7
PCIE3 0x6, 0x7
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
The DDR controller of 8548/8544/8568/8572/8536 processors
have the ECC data init feature, and the new DDR code is
using the feature, and we don't need the way with DMA to
init memory any more.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This patch defines 1M TLB&LAW size for NAND on MPC8572DS, assigns
0xffa00000 for CONFIG_SYS_NAND_BASE and adds other NAND supports in
config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image, to
make room for the increased code size with NAND enabled.
Signed-off-by: Jason Jin <Jason.Jin@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Converted ATUM8548, MPC8536DS, MPC8544DS, MPC8548CDS, MPC8568MDS,
MPC8572DS, TQM85xx, and SBC8548 to use fsl_pci_setup_inbound_windows()
and ft_fsl_pci_setup().
With these changes the board code is a bit smaller and we get dma-ranges
set in the device tree for these boards.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andrew Fleming-AFLEMING <afleming@freescale.com>
mpc8572 supports all pcie controllers as end-points with cfg_host_agent=0.
Include host_agent == 0 decode for end-point determination.
This is not needed for the ds reference board since pcie3 will be a host
in order to connect to the uli chip. Include it here as a reference for
other mpc8572 boards.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
* Add board specific parameter table to choose correct cpo, clk_adjust,
write_data_delay, 2T based on board ddr frequency and n_ranks.
* Set odt_rd_cfg and odt_wr_cfg based on the dimm# and CS#.
* Set memory controller interleaving mode to bank interleaving, and disable
bank(chip select) interleaving mode by default, because the default on-board
DDR DIMMs are 2x512MB single-rank.
* Change CONFIG_ICS307_REFCLK_HZ from 33333333 to 33333000.
Signed-off-by: James Yang <James.Yang@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Because some dimm parameters like n_ranks needs to be used with the board
frequency to choose the board parameters like clk_adjust etc. in the
board_specific_paramesters table of the board ddr file, we need to pass
the dimm parameters to the board file.
* move ddr dimm parameters header file from /cpu to /include directory.
* add ddr dimm parameters to populate board specific options.
* Fix fsl_ddr_board_options() for all the 8xxx boards which call this function.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Changing the flash from cacheable to cache-inhibited was taking a significant
amount of time due to the fact that we were iterating over the full 256M of
flash. Instead we can just flush the L1 d-cache and invalidate the i-cache.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
