In raw mode, handle ctrl-c as normal. This allows normal ctrl-c behavior
such as aborting a command that is timing out without completely
terminating the sandbox executable.
In [1], Simon disabled this. His reason for it was that it interferes
with piping test scripts. Piping should be done in cooked mode, so this
change should still not interfere.
[1] commit 8969ea3e9f ("sandbox: Disable Ctrl-C")
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Explanation from Simon Glass
"Private data is created when the device is probed and freed when the
device is removed.
Platform data is created when the device is bound, and survives
probe/remove cycles.
Strictly speaking, platform data should be used to hold the decoded
device tree properties. Private data should be used for run-time
things the device needs to keep track of."
Based on description the driver needs to be switch to use platdata
instead of priv.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add code to reset all reset signals as in serial DT node. A reset
property is an optional feature, so do not fail if a reset property is
not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds Actions Semi OWL family UART support. This driver
relies on baudrate configured by primary bootloaders.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
In Linux, the clock rate of the UART is given by the clock driver.
If you try to follow that in U-Boot, you would end up with adding
more u-boot,dm-pre-reloc properties, and also the clock driver would
be too big for SPL, which is used for UniPhier ARMv7 platform.
The current solution is to add 'clock-frequency' property to the
UART nodes, but it does not exist in the DT files in Linux. I do
not want to let DT diverge for U-Boot.
Check the SoC compatible and set the clock rate according to it.
This will be helpful to sync DT between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This function is used only inside this driver that's why should be
static.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This issue was found when OF_LIVE was enabled that there are scrambled
chars on the console like this:
Chip ID: zu3eg
Watchdog: Started��j� sdhci@ff160000: 0, sdhci@ff170000: 1
In: serial@ff010000
I found a solution for this problem exactly the same as I found later in
serial_msm fixed by:
"serial: serial_msm: initialize uart only before relocation"
(sha1: 7e5ad796bc)
What it is happening is that output TX fifo still contains chars to be
sent and _uart_zynq_serial_init() resets TX fifo even in the middle of
transfer.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change logic and put char to fifo till there is a space in output fifo.
Origin logic was that output fifo needs to be empty. It means only one
char was in output queue.
Also remove unused ZYNQ_UART_SR_TXEMPTY macro.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Coding style is checking to use BIT macros instead of shifts.
The patch is also fixing the rest of macros which should be BITs instead
of hex numbers.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add possibility to update the serial parity used.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Rename USART_ISR_FLAG_xxx bits to USART_ISR_xxx bits and
USART_ICR_OREF to USART_ICR_ORECF in order to match datasheets.
Sort defines by descendant order.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add support for early debug printf, before the availability of
driver model and device tree support.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Serial port configuration was missing from previous implementation.
It only worked because it was preconfigured by LK.
This patch configures the uart for 115200 8N1.
It also configures the pin mux for uart pins using DT bindings.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
The uart is already initialized prior to relocation,
reinitialization after relocation is unnecessary.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Failure to set the clocks will causes data abort exception when
trying to write to AHB uart registers.
This patch ensures that we don't touch these registers if clock
setting failed.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Xilinx ZynqMP also contains dual Cortex R5 which can run U-Boot.
This patch is adding minimal support to get U-Boot boot.
U-Boot on R5 runs out of DDR with default configuration that's why
DDR needs to be partitioned if there is something else running on arm64.
Console is done via Cadence uart driver and the first Cadence Triple
Timer Counter is used for time.
This configuration with uart1 was tested on zcu100-revC.
U-Boot 2018.05-rc2-00021-gd058a08d907d (Apr 18 2018 - 14:11:27 +0200)
Model: Xilinx ZynqMP R5
DRAM: 512 MiB
WARNING: Caches not enabled
MMC:
In: serial@ff010000
Out: serial@ff010000
Err: serial@ff010000
Net: Net Initialization Skipped
No ethernet found.
ZynqMP r5>
There are two ways how to run this on ZynqMP.
1. Run from ZynqMP arm64
tftpb 20000000 u-boot-r5.elf
setenv autostart no && bootelf -p 20000000
cpu 4 disable && cpu 4 release 10000000 lockstep
or
cpu 4 disable && cpu 4 release 10000000 split
2. Load via jtag when directly to R5
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Currently CPU_V7 kconfig symbol supports only ARMv7A architectures under
armv7 folder. This led to a misconception of creating separate folders
for armv7m and armv7r. There is no reason to create separate folder for
other armv7 based architectures when it can co-exist with few Kconfig
symbols.
As a first step towards a common folder, rename CPU_V7 as CPUV7A. Later
separate Kconfig symbols can be added for CPU_V7R and CPU_V7M and
can co exist in the same folder.
Reviewed-by: Tom Rini <trini@konsulko.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
Suggested-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.
In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.
This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.
Signed-off-by: Tom Rini <trini@konsulko.com>
Uart status register is named USART_ISR on STM32F7, STM32H7
and STM32MP1 SoCs family, but USART_SR only on STM32F4 SoCs.
Use USART_ISR_ prefix instead of USART_SR_ .
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Enable uart overrun feature which allows to benefits of uart
FIFO usage.
Previously overrun management was disabled, this has to effect
to bypassed the uart FIFO usage even if FIFO was enabled.
In particular configuration, for example when video console is
enabled, copy/pasting a long command line in console results in
corruption. This is due to the fact that a lot of time is consumed
in flushing the cache during frame buffer update, so uart chars are
not read fast enough.
By using uart FIFO and managing overrun, long command line can by
copy/paste in console without being corrupted.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
The line "-obj-$(CONFIG_STM32_SERIAL) += serial_stm32.o"
is found twice in Makefile.
Fixes: ae74de0dfd ("serial: stm32: Rename serial_stm32x7.c to serial_stm32.c"
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Acked-by: Vikas Manocha <vikas.manocha@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the SCIFA0 address entry so it can be used in TPL if needed
due to size restrictions.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
This patch fixes a situation where CONFIG_DM_SERIAL is enabled for
regular U-Boot and SPL, but not for TPL. In that case, the build
will try to include serial-uclass into the TPL nonetheless, because
CONFIG_DM_SERIAL is set.
The solution is to check if the build is for SPL or TPL and in that
case, check if CONFIG_$(SPL_TPL_)DM_SERIAL is also set. Only in that
case, include serial-uclass.c . If the build is for regular U-Boot,
CONFIG_BUILD is not set, so only check if CONFIG_DM_SERIAL is set
and if so, include serial-uclass.c
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
The Amlogic Meson SoCs serial bindings were not written when serial
support was pushed into Linux and U-Boot.
A clean bindings document has been merged into Linux tree to correctly
handle the multiple clocks feeding the serial peripheral.
This update the U-Boot serial_meson driver with the new compatible
string for Amlogic Meson GX Socs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
include/commproc.h is dedicated to the 8xx, rename it cpm_8xx.h and
move it into arch/powerpc/include/asm
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
CONFIG_8xx doesn't mean much outside of arch/powerpc/
This patch renames it CONFIG_MPC8xx just like CONFIG_MPC85xx etc ...
It also renames 8xx_immap.h to immap_8xx.h to be consistent with
other file names.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
- add new arch stm32mp for STM32 MPU/Soc based on Cortex A
- support for stm32mp157 SOC
- SPL is used as first boot stage loader
- using driver model for all the drivers, even in SPL
- all security feature are deactivated (ETZC and TZC)
- reused STM32 MCU drivers when it is possible
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt on Raspberry Pis that use pl011 for serial.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
After the UART was initialized, we may still have bogus data in the
RX queue if it was enabled with incorrect pin muxing before.
So let's flush the RX queue whenever we initialize baud rates.
This fixes a regression with the dynamic pinmuxing code when enable_uart=1
is not set in config.txt.
Fixes: caf2233b28 ("bcm283x: Add pinctrl driver")
Reported-by: Göran Lundberg <goran@lundberg.email>
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Do a explicit check for CONFIG_SYS_BIG_ENDIAN and
CONFIG_SYS_LITTLE_ENDIAN to avoid errors on platforms where both
are undefined (x86).
Signed-off-by: Bernhard Messerklinger <bernhard.messerklinger@br-automation.com>
Reviewed-by: Hannes Schmelzer <hannes.schmelzer@br-automation.com>
Commit 608b0c4ad4 ("serial: Use next serial device if probing fails")
added code to search for more serial devices if the default one was not
probed correctly.
Unfortunately, that breaks omap3_evm. So while investigating why that is
the case, let's disable the full search for everyone but bcm283x where it
is needed.
Fixes: 608b0c4ad4 ("serial: Use next serial device if probing fails")
Reported-by: Derald D. Woods <woods.technical@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
On bcm2835 we need to ensure we only access serial devices that are
muxed to the serial output pins of the pin header. To achieve this
for the pl011 device, add a bcm2835 specific pl011 wrapper device
that does this check but otherwise behaves like a pl011 device.
Signed-off-by: Alexander Graf <agraf@suse.de>
Setting config options using headers is deprecated. This patch converts
the BCM2835 Mini-UART to Kconfig.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl01x.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl011.
Signed-off-by: Alexander Graf <agraf@suse.de>
We want to use Kconfig logic to depend on whether pl01x devices
are built in, so let's convert their inclusion selection to Kconfig.
This round goes to pl010.
Signed-off-by: Alexander Graf <agraf@suse.de>
The bcm283x mini-uart is only really usable as U-Boot serial output
when it is muxed to the UART pins of the RPi pin header.
So fail probing in case it is not muxed correctly, as in that case
firmware did not initialize it properly either.
Signed-off-by: Alexander Graf <agraf@suse.de>
