s_init has the same outline for all the AM33xx based
board. So making it generic.
This also helps in addition of new Soc with minimal changes.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Tested-by: Heiko Schocher <hs@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
NOR requires that s_init be within the first 4KiB of the image so that
we can perform the rest of the required pinmuxing to talk with the rest
of NOR that we are found on. When NOR_BOOT is set we save our
environment in NOR at 512KiB and a redundant copy at 768KiB. We avoid
using SPL for this case and u-boot.bin is written directly to the start
of NOR.
We enclose the DMM-related parts of arch/arm/cpu/armv7/am33xx/emif4.c
with TI81xx checks as at this time U-Boot does not discard unused
sections in the main build and this code relies on functions specific to
(and only provided in) ti81xx-related code.
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds support for the NOR module that attaches
to the memory cape for a Beaglebone board. This does not
add booting support; only support so that you can boot from
SD/MMC and see the NOR module so that it can be programmed.
Signed-off-by: Steve Kipisz <s-kipisz2@ti.com>
[trini: Clean up config changes slightly]
Signed-off-by: Tom Rini <trini@ti.com>
We rework the various board_is_foo() checks to take a pointer to
struct am335x_baseboard_id rather than using a local copy in board.c.
This allows us to make use of the same checks in mux.c as well as fixing
problems when this code could be running from read-only memory.
Reviewed-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Tom Rini <trini@ti.com>
This patch extends the am335x_evm board for the AM335x IDK.
The IDK board uses MII for the ethernet phy (same as
Beaglebone board) and MMC0 for storage (but without
card detect line).
The IDK uses UART3 for console. So u-boot must be build
with CONFIG_SERIAL4 and CONFIG_CONS_INDEX=4 or for
the am335x_evm_uart3 board configuration as introduced
by Andrew Bradfords recent patch series "am33xx: Enable
UART {1,2,3,4,5}...". When using the IDK with console on UART0,
those patches are not required. In this case the board
slightly needs to be modified.
Signed-off-by: Matthias Fuchs <matthias.fuchs@esd.eu>
This fixes the following boothang in SPL:
Unknown board, cannot configure pinmux.### ERROR ### Please RESET the board ###
Future commits will add pinmuxes for more on-board peripherals.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
If configured to use UART{1,2,3,4,5} such as on the Beaglebone RS232
cape or on the am335x_evm daughterboard, enable the proper pin-muxing.
Signed-off-by: Andrew Bradford <andrew@bradfordembedded.com>
The i2c header is specific to ti(-derived) boards, and not generic for all
am335x boards.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
[trini: Make re-apply with rtc32k_enable() applied]
Signed-off-by: Tom Rini <trini@ti.com>
The AM335x GP EVM can have one of 8 different profiles selected. Each
profile has a different set of peripherals and requires different pinmux
configurations that conflict with other profiles. i2c1 is an example of
a conflicted mux currently.
Signed-off-by: Tom Rini <trini@ti.com>
- Move definition of the EEPROM contents to <asm/arch/sys_proto.h>
- Make some defines a little less generic now.
- Pinmux must be done by done by SPL now.
- Create 3 pinmux functions, uart0, i2c0 and board.
- Add pinmux specific to Starter Kit EVM for MMC now.
Signed-off-by: Tom Rini <trini@ti.com>
- Board requires gpio0 #7 to be set to power DDR3.
- Board uses DDR3, add a way to determine which DDR type to call
config_ddr with.
- Both of the above require filling in the header structure early, move
it into the data section.
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds pin mux settings for CPSW switch found on
TI AM335X based boards (MII and RGMII modes).
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
[Ilya: split pinmux into separate patch]
Signed-off-by: Ilya Yanok <ilya.yanok@cogentembedded.com>
This patch is added to support SPL feature on AM335X
platform. In this patch, MMC1 is configured as boot
device for SPL and support for other devices will be
added in the next patch series.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Igor Grinberg <grinberg@compulab.co.il>
This patch add supports for mmc/sd driver on AM335X platform.
PLL and pinmux configurations for mmc/sd are configured in this
patch.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Tom Rini <trini@ti.com>
This patch adds basic support for booting the board.
This patch adds support for the UART necessary to
get to the u-boot prompt.
Signed-off-by: Chandan Nath <chandan.nath@ti.com>
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
