Some phys require a phy-supply property that is a phandle to a regulator
that needs to be enabled for phy operations.
Implement basic supply lookup, enable and disabling, if DM_REGULATOR is
available.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
[jonas@kwiboo.se:
use regulator_set_enable_if_allowed and disable if power_on ops fails]
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
- Merge in a long-standing fix for some exynos platforms, correct a
Kconfig description, fix some env issues, fix an issue in
devfdt_get_addr_size_index_ptr and look for "panel-timings" not
"panel-timing" per upstream binding.
For the devfdt_get_addr_size_index_ptr() function use
map_sysmem() function as cast for the return for use in
sandbox.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
In case where a single timing resolution is implemented in the
device-tree, the property is named "panel-timing", as specify
in Linux kernel binding file:
Documentation/devicetree/bindings/display/panel/panel-common.yaml
# Display Timings
panel-timing:
description:
Most display panels are restricted to a single resolution and
require specific display timings. The panel-timing subnode expresses those
timings.
$ref: panel-timing.yaml#
display-timings:
description:
Some display panels support several resolutions with different timings.
The display-timings bindings supports specifying several timings and
optionally specifying which is the native mode.
$ref: display-timings.yaml#
Fixes: 0347cc7732 ("drivers: core: ofnode: Add panel timing decode.")
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This reverts commit a034ec06ff.
Commit 4a3ea75de4 ("Revert "mmc: sdhci: set to INT_DATA_END when
there are data"") reverted the alternative fix that was added for
Exynos 4 devices, causing an error when trying to boot from an sdcard:
<...>
Loading Environment from MMC... sdhci_send_command: Timeout for status update!
mmc fail to send stop cmd
<...>
Re-add the quirk to allow booting from sdcards again.
Signed-off-by: Henrik Grimler <henrik@grimler.se>
Make it clear that this is the SPL option to avoid potential confusion
when the description for CONFIG_SPL_VIDEO is the same as that for
CONFIG_VIDEO.
Signed-off-by: John Keeping <john@metanate.com>
flash_get_size() will get the flash size from the device itself and go
through all erase regions to read protection status. However, the device
mappable region (eg: devicetree reg property) might be lower than the
device full size which means that the above cycle will result in a data
bus exception. This change fixes it by reading the 'addr_size' during
probe() and also use that as one possible upper limit.
Signed-off-by: Nuno Sá <nuno.sa@analog.com>
This reverts commit e097847286. The
commit wrongly divides the dummy bytes by dummy bus width to calculate
the dummy bytes. The framework already converts the dummy cycles to the
number of bytes and the controller use the SPI flash command to
determine the dummy cycles via the address width.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Acked-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230427065355.7413-1-stefan.herbrechtsmeier-oss@weidmueller.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
This causes crashes on some boards, e.g. rockpro64. In any case, we
should not do it.
Check the usb_started flag to avoid this.
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Jonas Karlman <jonas@kwiboo.se>
Tested-by: Tom Rini <trini@konsulko.com>
This should be declared in a header file so that type-checking works
correctly.
Add a single declaration to usb.h and remove the others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Add support for Schneider Electric RZ/N1D and RZ/N1S boards, which
are based on the Reneasas RZ/N1 SoC devices.
The intention is to support both boards using a single defconfig, and to
handle the differences at runtime.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Driver for Cadence EDAC DDR controller, as found in the Renesas RZ/N1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Pinctrl/pinconf driver for Renesas RZ/N1 (R906G032) SoC.
This is quite rudimentary right now, and only supports applying a
default pin configuration as specified by the device tree.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Clock driver for the Renesas RZ/N1 SoC family. This is based on
Linux kernel 6.2.y drivers/clk/renesas/r9a06g032-clocks.c as found in
commit 02693e11611e ("clk: renesas: r9a06g032: Repair grave increment error"),
with the following additional patch series applied:
https://lore.kernel.org/linux-renesas-soc/20230301215520.828455-1-ralph.siemsen@linaro.org/
Notable difference: this version avoids allocating a 'struct clk'
for each clock source, as this is problematic before relocation.
Instead, it uses the same approach as existing Renesas R-Car Gen2/3
clock drivers, using a temporary structure filled on-the-fly.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Add new CONFIG_CLK_RCAR to control compilation of shared code for R-Car
clock drivers (renesas-cpg-mssr.c). Enable this for R-Car Gen2 and 3.
This is necessary so that CONFIG_CLK_RENESAS can be enabled, allowing
recursion into the drivers/clk/reneasas directory, without bringing in
the R-Car support code. The support code contains platform specific
access (TMU_BASE) which is not needed on other Renesas devices such as
RZ/N1.
Signed-off-by: Ralph Siemsen <ralph.siemsen@linaro.org>
Reviewed-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Probing LPC can cause PCI enumeration to take place, which significantly
increases pre-relocation memory usage. Also, LPC is somtimes enabled
directly by SPL.
Adjust the logic to probe the LPC only after relocation. This allows
chromebook_link64 to start up without a much larger
CONFIG_SYS_MALLOC_F_LEN value.
Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The 'tiny' SPI nor functions have the same name as their big brothers,
which can be confusing. Use different names so it is clear which
version is in the image.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
With tiny SPI flash the erasesize is 0 which can cause a divide-by-zero
error. Check for this and return a proper error instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
The original function was only called once, before relocation. The new
one is called again after relocation. This was not the intent of the
original call. Fix this by renaming and updating the calling logic.
With this, chromebook_link64 makes it through SPL.
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
U-Boot sets up devices ready for use, but coreboot does not. Enable this
so that NVMe works OK from coreboot.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
When U-Boot is the second-stage bootloader, PCI is already set up. We
cannot read the regions from the device tree. There is no point anyway,
since PCI devices have already been allocated according to the regions
and it is not safe for U-Boot to make any changes.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Fixes: f2ebaaa9f3 ("pci: Handle failed calloc in decode_regions()")
Tested-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
When coreboot does not pass a UART in its sysinfo struct, there is no
easy way to find it out.
Since coreboot does not actually init the serial device when serial is
disabled, it is not possible to make it add this information to the
sysinfo table.
Add a way to obtain this information from the DBG2 ACPI table, which is
normally set up by coreboot.
For now this only supports a memory-mapped 16550-style UART.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
We have several Kconfig options for ACPI, but all relate to specific
functions, such as generating tables and AML code.
Add a new option which controls including basic ACPI library code,
including the lib/acpi directory. This will allow us to add functions
which are available even if table generation is not supported.
Adjust the command to avoid a build error when ACPIGEN is not enabled.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
If U-Boot is not the first-stage bootloader the keyboard may already be
set up. Make sure to flush any data before trying to reset it. This
avoids a long timeout / hang.
Add some comments and a log category while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
- Rockchip NFC driver update and dev addr pointer api update;
- use standard dr_mode for usb driver;
- rock pi boards dts update;
- Add rk3566 Anbernic boards;
- Misc fixes for drivers;
The CRU is being probed with a default set of assigned clocks, which
are not implemented in the driver at all.
Hence, when clk_set_defaults is called, it fails with ENOENT.
This would not be a problem, as the CRU still handles all the required
clocks, and the assigned clocks are default configs which are preprogrammed
or not required for Uboot operations.
However, the rockchip reset driver is being bound by the same DT node
as CRU, as the reset driver has no DT node.
But, when probing the reset node, it will call again the clk_set_defaults
for the CRU node, and failing because of missing those specific clocks
in the rk3588 clock driver.
To avoid this, simply implement a basic set/get that will just return
success and the default corresponding rate for the required assigned clocks.
As those clocks were not supported in Uboot, not required for Uboot
operations, there is no need to do any different kind of initialization.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix line spacing aligment in bind function
Fixes: 760188c1aa ("rockchip: reset: support a (common) rockchip reset drivers")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Implement a resource release mechanism on failing probe.
Without this, a strange situation can happen e.g. when init port fails,
or attempting to get the PHY fails, because the gpios have been
requested first, and if the user tries to do 'pci enum' again, the
driver will fail with 'can't find reset gpios' even if the gpios are
there, just because they were blocked by a previous probe attempt.
It is only natural to release the acquired resources if the probe fails,
just for consistency if nothing else.
This way on subsequent probe attempts, the user will get the same error
message, and not something different that doesn't make sense.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so fix some
debug strings with fdt_addr_t to be able to handle both sizes.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
devfdt_get_addr_ptr instead of the devfdt_get_addr function in
the various files in the drivers directory that cast to a pointer.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
devfdt_get_addr_index_ptr instead of the devfdt_get_addr_index function
in the various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
devfdt_get_addr_size_index_ptr instead of the devfdt_get_addr_size_index
function in the various files in the drivers directory that cast to
a pointer.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_ptr instead of the dev_read_addr function in the
various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled. A 32bit CPU
can expect 64-bit data from the device tree parser, so use
dev_read_addr_index_ptr instead of the dev_read_addr_index function
in the various files in the drivers directory that cast to a pointer.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so use devfdt_get_addr_index_ptr and devfdt_get_addr_size_index_ptr
function in the spi-aspeed-smc.c file. Also fix dev_dbg to be able
to handle both sizes. As we are there also streamline the error
response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Add dev_read_addr_index_ptr function with the
same functionality as dev_read_addr_index,
but instead a return pointer is given.
Use map_sysmem() function as cast for the return.
Make same fix for dev_read_addr_ptr() function.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add devfdt_get_addr_size_index_ptr function with the same
functionality as devfdt_get_addr_size_index, but instead
a return pointer is given.
Suggested-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so convert regmap_init_mem_plat() input to handel both. The
syscon class driver also makes use of the regmap_init_mem_plat()
function, but has no way of knowing the format of the
device-specific platform data. In case of odd reg structures other
then that the syscon class driver assumes the regmap must be
filled in the individual syscon driver before pre-probe.
Also fix the ARRAY_SIZE divider in the syscon class driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so use a base variable with uintptr_t size in the
rk_spi.c file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so use a base variable with uintptr_t size in the
rk_pwm.c file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expect 64-bit data from the device tree parser,
so use a regs variable with uintptr_t size in the
dw-apb-timer.c file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expext 64-bit data from the device tree parser,
so use dev_read_addr_ptr in the rockchip-saradc.c file.
As we are there also streamline the error response to -EINVAL on return.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sandisk SDTNQGAMA is a 8GB size, 3.3V 8 bit chip with 16KB page size,
1KB write size and 40 bit ecc support
Signed-off-by: Paweł Jarosz <paweljarosz3691@gmail.com>
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Michael Trimarchi <michael@amarulasolutions.com>
The MTD framework reserves 1 or 2 bytes for the bad block marker
depending on the bus size. The rockchip_nfc driver currently only
supports a 8 bit bus, but reserves standard 2 bytes for the BBM.
The first free OOB byte is therefore OOB2 at offset 2.
Page address(PA) bytes are moved to the last 4 positions before
ECC. Update the description for U-boot.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add flash_node to the rockchip_nfc driver chip structure in order
to find the partitions in the add_mtd_partitions_of() function.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
The MTD framework in U-boot is not identical for drivers ported
from Linux. The rockchip_nfc driver was ported with OOB ops functions
while the framework expects a layout structure per chip.
Fix by adding a structure with OOB data and remove unused functions.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
The compatible string for rk3308 has as fallback string
"rockchip,rv1108-nfc". As there is no logic in probe priority between
the SoC orientated string and the fall back, so remove the compatible
string "rockchip,rk3308-nfc" from the driver.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
The fdt_addr_t and phys_addr_t size have been decoupled.
A 32bit CPU can expext 64-bit data from the device tree parser,
so use dev_read_addr_ptr in the rockchip_nfc.c file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Request the reset gpio of the rgmii-id phy as output to be consistent
with the eth-phy-uclass driver.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Reviewed-by: Michal Simek <michal.simek@amd.com>
Add minimal support for 8125B version.
Changes are based on the Linux driver.
Tested on Radxa Rock 5B Rk3588 board.
Connection to a laptop worked fine in 100 Mbps mode.
1000 Mbps mode is not working at the moment.
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
dp83867 driver only supports sgmii and not all the newer protocols.
Drop the usage of the generic phy_interface_is_sgmii function and just
matchup to the specific mode supported.
Reported-by: Tom Rini <trini@konsulko.com>
Suggested-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
Suggested-by: Marek Behún <kabel@kernel.org>
Link: https://lore.kernel.org/all/b82ac325-4818-8e72-054b-640268dbf806@mailbox.org/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Introduce reboot, boot and continue commands support to
TCP fastboot by moving existing UDP logic into the common module.
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Known limitations are
1. fastboot reboot doesn't work (answering OK but not rebooting)
2. flashing isn't supported (TCP transport only limitation)
The command syntax is
fastboot tcp
Signed-off-by: Dmitrii Merkurev <dimorinny@google.com>
Cc: Ying-Chun Liu (PaulLiu) <paul.liu@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Сс: Joe Hershberger <joe.hershberger@ni.com>
Сс: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
rtl8211e_startup() is an exact copy of genphy_startup(). Use that
instead of duplicating it.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Read the phy mode of the external phy from the device tree if available
and check that it is a RGMII variant.
Signed-off-by: Stefan Herbrechtsmeier <stefan.herbrechtsmeier@weidmueller.com>
Without that patch it lost track to the node to scan
speed and duplex.
Patch was created by Marek Vasut, just tested by me.
Signed-off-by: Elmar Psilog <epsi@gmx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
In the process of adopting CONFIG_DM_ETH on the DPAA2 based platforms,
interfaces which were previously defined as "xgmii" were transitioned to
be defined as "xfi" in the DTS.
See the commit below for reference:
commit 87274918f2 ("arm: dts: ls2088ardb: add DPMAC and PHY nodes")
Then Vladimir's commit replaced all occurrences of "xfi" with
"10gbase-r" in an effort to make U-Boot work with the same device tree
as Linux.
commit 77b11f7604 ("net: replace the "xfi" phy-mode with "10gbase-r"")
These changes to the phy_interface_t of an Ethernet port meant that the
mc_fixup_mac_addrs() function was no longer capable to properly fixup
the MAC addresses. The problem arises from the fact that the hardcoded
information about an interface (wriop_get_enet_if()) was no longer
matching any actual device.
For example, the function tried to search for "DPMAC1@xgmii1" by name
using eth_get_dev_by_name() when only "DPMAC1@10gbase-r" was available.
This function removes the need to rely on the hardcoded information by
iterating through all the UCLASS_ETH devices which are DPAA2 and request
a fixup for each of them.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Export the ldpaa_eth_get_dpmac_id() function so that it can be used from
other drivers, especially by fsl-mc which will need it the next patch.
Also, create a macro for the Ethernet ldpaa driver name and export it as
well.
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Add a port_probe function to configure the phy. This leads to
earlier link negotiation so the port is more likely to be ready
when used.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
We don't do anything useful with the master dev, so remove the variable.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
packet tagging is not used for this driver so we do not need to
call dsa_set_tagging.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Instead of inhibiting parameter RAM relacation, take
into account the configured one.
It means INIT_TRX command cannot be used and must be done
manually as explained in the microcode patch application note.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
This allows the Layerscape PCIe RC driver to use the upstream
style binding (two "reg" entries instead of four).
It is similar to the previous commit e10da1f985
("pci: layerscape: add official ls1028a binding support")
which implemented this for the LS1028A.
Signed-off-by: Mathew McBride <matt@traverse.com.au>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Tested-by: Ioana Ciornei <ioana.ciornei@nxp.com> # on LS1088A-RDB
ESM MCU masks must be set to 0h so that PMIC can handle errors
that require attention for example SYS_SAFETY_ERRn. The required bits
must be cleared: ESM_MCU_RST_MASK, ESM_MCU_FAIL_MASK, ESM_MCU_PIN_MASK.
If PMIC expected to handle errors, make sure EVM is configured to
connect SOC_SAFETY_ERRz (Main) to the PMIC.
Note that even though the User Guide for TPS65941 for J721E mentions
that these bits are reset to 0h; it is not reflected once board boots to
kernel, possibly due to NVM configurations. Eithercase, it is best to
account for this from R5 SPL side as well.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
With relocation, CPM parameter RAM can be anywhere in the
dual port RAM, so don't split dual port RAM.
Remove dparam and dparam16 members of struct comm_proc
PROFF_XXX become offsets from the start of dual port RAM,
then they are now consistant with the offsets in RPBASE
registers.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Freescale PCIe Root Port has PEXCSRBAR register at position of PCI BAR0.
PCIe Root Port does not have any PCIe memory, so returns zero when trying
to read from PCIe Root Port BAR0 and ignore any writes.
Signed-off-by: Pali Rohár <pali@kernel.org>
It adds compatible "hisilicon,hi3798mv200-dw-mshc" for HC2910 SoC
Hi3798MV200 to probe this mmc driver.
Signed-off-by: Yang Xiwen <forbidden405@outlook.com>
Commit dafe0fbfb0 ("pinctrl: mediatek: rewrite mtk_pinconf_set and
related functions") changed the logic deciding to set R0 and R1
registers for V1 devices.
Before:
/* Also set PUPD/R0/R1 if the pin has them */
err = mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_PUPD, !pullup);
if (err != -EINVAL) {
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R0, r0);
mtk_hw_set_value(dev, pin, PINCTRL_PIN_REG_R1, r1);
}
After:
/* try pupd_r1_r0 if pullen_pullsel return error */
err = mtk_pinconf_bias_set_pullen_pullsel(dev, pin, disable, pullup,
val);
if (err)
return mtk_pinconf_bias_set_pupd_r1_r0(dev, pin, disable,
pullup, val);
Tracing mtk_pinconf_bias_set_pullen_pullsel shows that the function
always either returns 0 in case of success or -EINVAL in case any error
has occurred. Hence the logic responsible of the decision to program R0
and R1 has been inverted.
This leads to problems on BananaPi R2 (MT7623N) when booting from
SDMMC, it turns out accessing eMMC no longer works since
U-Boot 2022.07:
MT7623> mmc dev 0
Card did not respond to voltage select! : -110
The problem wasn't detected for a long time as both eMMC and SDMMC work
fine if they are used to boot from, and hence R0 and R1 were already
setup by the bootrom and/or preloader.
Fix the logic to restore the originally intended and correct behavior
and also change the descriptive comment accordingly.
Fixes: dafe0fbfb0 ("pinctrl: mediatek: rewrite mtk_pinconf_set and related functions")
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-By: Frank Wunderlich <frank-w@public-files.de>
Starting from QUP v2.5 the value of oversampling is changed from 32
to 16, keeping the old value on newer platforms results on wrong set
UART IP clock divider, thus the asked baudrate does not correspond to
the actually set with all the consequencies for a user.
The change links the driver to a new Qualcomm GENI SE QUP driver
to get its hardware version and update the oversampling value.
Deliberately the code under CONFIG_DEBUG_UART_MSM_GENI is not touched,
since a wanted baudrate can be controlled by setting a modified
CONFIG_DEBUG_UART_CLOCK build time variable.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
The name "se" is used in upstream Linux device trees and has been for
ages, long before this U-Boot-ism was introduced. Same goes for the
existing compatible. Get rid of that.
[vzapolskiy: removed a ready change in the driver]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
A compiler warns about a missing function prototype, which is valid
and fixed by converting the function into static one, also fix
interleaved local variable declarations and assignments.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Fixes: 324df15a29 ("serial: qcom: add support for GENI serial driver")
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
This a cosmetic change, which corrects code indentation in a few places.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
There is only one clock supplier to the serial IP, thus getting it by
name is not needed, also note that "clock-names" property is not listed
under doc/device-tree-bindings/serial/msm-geni-serial.txt, and finally
"se-clk" clock name is invalid, if added, it shall get "se" value like
it's already described in Linux device tree documentation.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
In preparation for supporting upstream Linux device trees on Qualcomm
platforms, make this the default behavior.
[vzapolskiy: extracted the driver change from a combination with dts changes]
Signed-off-by: Konrad Dybcio <konrad.dybcio@linaro.org>
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
For whatever reason, likely a driver stub was copied from another
driver, the driver contains a bunch of unnecessary and confusing
includes like watchdog.h etc., the change reduces the list.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
This change adds a Qualcomm GENI SE QUP device driver as a wrapper for
actually enabled and used serial devices found on a board.
At the moment the driver is pretty simple, its intention is to populate
childred devices and provide I/O mem read interface to them as clients,
this is needed for GENI UART driver to set up a proper clock divider
and provide the actually asked baud rate.
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
MAX14526 is a powerful extcon chip which allows detection of various
plugs like usb, mhl, uart, headset etc. This version of driver
implements support of AP-usb and CP-usb/uart paths.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a new simple uclass for extcon. Currently all setup is done
in the probe. Uclass struct and ops are empty for now.
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
PCI autoconfig case for PCI_CLASS_PROCESSOR_POWERPC just prints debug
message and then calls autoconfig setup code like for any other standard
endpoint device. We do not need special debug message for it, so remove
this case and handle PCI_CLASS_PROCESSOR_POWERPC via default code path.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
For the CONFIG_PHY case, move the PHY setup before the register access.
This avoids a hang when updating the imx8mm.dtsi which moves the
USB OTG power-domains to the PHY.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Tested-by: Fabio Estevam <festevam@denx.de>
At BDF address 00:00.0 is fictional device which PCI configuration header
is for configuring mpc85xx PCI controller itself. PCI config space of this
device has ATMU inbound registers on position of PCI BARs. Trying to do PCI
auto configuration of this device cause rewriting ATMU inbound registers.
To avoid it, do not allow overwriting registers at BARs positions. And
because this device does not have any PCI memory, return zeros when trying
to read PCI BARs config space registers. It signals to auto configuration
tool to not allocate any PCI memory for this device.
This information is taken from MPC8544E Reference Manual, sections
17.3.1.3, 17.3.1.1.1, 17.3.2 and 17.3.2.11. Available at NXP website:
https://www.nxp.com/docs/en/reference-manual/MPC8544ERM.pdf
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Driver pci_mpc85xx.c is PCI controller driver for old PCI Local Bus,
which does not support access to extended PCIe registers (above 0xff),
as opposite of the PCIe driver pcie_fsl.c for the same platform.
So do not try to access extended PCIe registers as it cannot work.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
This Freescale mpc85xx PCI controller should support 8-bit and 16-bit read
and write access to PCI config space as described in more Freescale
reference manuals.
This change fixes issue that 8-bit and 16-bit write to PCI config space
caused to clear adjacent bits of 32-bit PCI register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
On PowerPC we should use barrier after store operation to HW register.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
Tested-by: Heiko Schocher <hs@denx.de>
Please pull the second part of the sunxi pull request for this cycle.
Another bunch of patches that replace old-school U-Boot hacks with
proper DM based code, this time for the raw NAND flash driver, and the
USB PHY VBUS detection code. Plus two smaller patches that were sitting
in my inbox for a while.
Gitlab CI passed. In lack of some supported board with NAND flash I
couldn't really test this part, but apparently this was tested by the
reviewer. I briefly ran the branch on some boards with USB-OTG, and
this still worked.
This pull request adds support for the last CPU board from
CS GROUP France (previously CSSI).
That CPU board called CMPCPRO has a mpc8321E CPU (Family PQII PRO hence
its name) and can be plugged in place of the CMPC885 board.
In order to support that new board, the following changes are included
in this series:
- Make the mpc8xx watchdog driver more generic for reusing it
with mpc83xx
- Fix various small problems on mpc83xx platform
- Add a GPIO Driver for QE GPIOs
- Add support for mpc832x into mpc83xx SPI driver
- Refactor existing board code that will be shared with new board
- Add the new board
For the devfdt_get_addr_index_ptr() and devfdt_get_addr_size_index_ptr()
function use map_sysmem() function as cast for the return for use in
sandbox. Also fix sandbox test.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Drop second hunk:
Signed-off-by: Simon Glass <sjg@chromium.org>
There's quite a few instances of board-specific code doing
off = fdt_path_offset(gd->fdt_blob, ...);
...
ret = uclass_get_device_by_of_offset(..., off, &dev);
looking for an eeprom or a pmic via some alias. Such code can be
simplified a little if we have a helper for directly getting a device
via device tree path (including being given as an alias).
Implement it in terms of ofnode rather than raw offsets so that this
will work whether live tree is enabled or not.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
