Kill multiple occurances and redeclaration of MK_STR
in favor of __stringify().
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Exactly one board has defined CONFIG_SYS_PROMPT_HUSH_PS2 to a value
different than "> " which is vision2. I have Cc'd the maintainer here
as I strongly suspect this is a bug rather than intentional behavior.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Remove MK_STR from places that consume CONFIG_BOOTFILE to force all definitions to be string literals.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Remove MK_STR from places that consume CONFIG_ROOTPATH to force all definitions to be string literals.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Now that none of the core checks CONFIG_NET_MULTI, there's not much point
in boards defining it. So scrub all references to it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Some new platform's esdhc pins don't share with other function.
The eSDHC shouldn't be disabled, even if "esdhc" isn't defined
in hwconfig env variable.
Use CONFIG_FSL_ESDHC_PIN_MUX to fix this problem.
Signed-off-by: Chenhui Zhao <b26998@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_GBL_DATA_SIZE has always been just a bad workarond for not
being able to use "sizeof(struct global_data)" in assembler files.
Recent experience has shown that manual synchronization is not
reliable enough. This patch renames CONFIG_SYS_GBL_DATA_SIZE into
GENERATED_GBL_DATA_SIZE which gets automatically generated by the
asm-offsets tool. In the result, all definitions of this value can be
deleted from the board config files. We have to make sure that all
files that reference such data include the new <asm-offsets.h> file.
No other changes have been done yet, but it is obvious that similar
changes / simplifications can be done for other, related macro
definitions as well.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
CONFIG_SYS_INIT_RAM_END was a misnomer as it suggests this might be
some end address; to make the meaning more clear we rename it into
CONFIG_SYS_INIT_RAM_SIZE
No other code changes are performed in this patch, only minor editing
of white space (due to the changed length) and the comments was done,
where noticed.
Note that the code for the PATI and cmi_mpc5xx board configurations
looks seriously broken. Last known maintainers on Cc:
Signed-off-by: Wolfgang Denk <wd@denx.de>
Cc: Denis Peter <d.peter@mpl.ch>
Cc: Martin Winistoerfer <martinwinistoerfer@gmx.ch>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Now that warm booting is not supported, there isn't a need for the
BOOTFLAG_COLD and BOOTFLAG_WARM defines, so remove them.
Note that this change makes the board info bd_bootflags field useless.
It will always be set to 0, but we leave it around so that we don't
break the board info structure that some OSes are expecting to be passed
from U-Boot.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Clean up Makefile, and drop a lot of the config.mk files on the way.
We now also automatically pick all boards that are listed in
boards.cfg (and with all configurations), so we can drop the redundant
entries from MAKEALL to avoid building these twice.
Signed-off-by: Wolfgang Denk <wd@denx.de>
The change is currently needed to be able to remove the board
configuration scripting from the top level Makefile and replace it by
a simple, table driven script.
Moving this configuration setting into the "CONFIG_*" name space is
also desirable because it is needed if we ever should move forward to
a Kconfig driven configuration system.
Signed-off-by: Wolfgang Denk <wd@denx.de>
Newer Linux kernels can overrun the initial memory window used for
booting with their BSS area. When this happens, they overwrite the FDT
and silently fail to boot.
On e300 CPUs, the Linux kernel uses an initial BAT covering the first
256MB of RAM. See arch/powerpc/kernel/head_32.S for details. Increase
the value of CONFIG_SYS_BOOTMAPSZ to accommodate the maximum value
allowed by Linux. This will allow very large kernels to boot.
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch removes the completely unused CONFIG_SERIAL_SOFTWARE_FIFO
feature from U-Boot. It has only been implemented for PPC4xx and was not
used at all. So let's remove it and make the code smaller and cleaner.
Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Detlev Zundel <dzu@denx.de>
Some parts that have an Enhanced Local Bus Controller weren't
setting CONFIG_FSL_ELBC. Fix this so we can use this define
properly going forward (currently it's only used if PHYS_64BIT is
set, which meant not all platforms needed to have it set correctly).
Signed-off-by: Becky Bruce <beckyb@kernel.crashing.org>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
before, MPC8349ITX boots u-boot in 4.3sec:
column1 is elapsed time since first message
column2 is elapsed time since previous message
column3 is the message
0.000 0.000: U-Boot 2010.03-00126-gfd4e49c (Apr 11 2010 - 17:25:29) MPC83XX
0.000 0.000:
0.000 0.000: Reset Status:
0.000 0.000:
0.032 0.032: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.032 0.000: Board: Freescale MPC8349E-mITX
0.032 0.000: UPMA: Configured for compact flash
0.032 0.000: I2C: ready
0.061 0.028: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
1.516 1.456: FLASH: 16 MB
2.641 1.125: PCI: Bus Dev VenId DevId Class Int
2.652 0.011: 00 10 1095 3114 0180 00
2.652 0.000: PCI: Bus Dev VenId DevId Class Int
2.652 0.000: In: serial
2.652 0.000: Out: serial
2.652 0.000: Err: serial
2.682 0.030: Board revision: 1.0 (PCF8475A)
3.080 0.398: Net: TSEC1: No support for PHY id ffffffff; assuming generic
3.080 0.000: TSEC0, TSEC1
4.300 1.219: IDE: Bus 0: .** Timeout **
after, MPC8349ITX boots u-boot in 3.0sec:
0.010 0.010: U-Boot 2010.03-00127-g4b468cc-dirty (Apr 11 2010 - 17:47:29) MPC83XX
0.010 0.000:
0.010 0.000: Reset Status:
0.010 0.000:
0.017 0.007: CPU: e300c1, MPC8349E, Rev: 1.1 at 533.333 MHz, CSB: 266.667 MHz
0.017 0.000: Board: Freescale MPC8349E-mITX
0.038 0.020: UPMA: Configured for compact flash
0.038 0.000: I2C: ready
0.038 0.000: DRAM: 256 MB (DDR1, 64-bit, ECC off, 266.667 MHz)
0.260 0.222: FLASH: 16 MB
1.390 1.130: PCI: Bus Dev VenId DevId Class Int
1.390 0.000: 00 10 1095 3114 0180 00
1.390 0.000: PCI: Bus Dev VenId DevId Class Int
1.400 0.010: In: serial
1.400 0.000: Out: serial
1.400 0.000: Err: serial
1.400 0.000: Board revision: 1.0 (PCF8475A)
1.832 0.432: Net: TSEC1: No support for PHY id ffffffff; assuming generic
1.832 0.000: TSEC0, TSEC1
3.038 1.205: IDE: Bus 0: .** Timeout **
also tested on these boards (albeit with a less accurate
boottime measurement method):
seconds: before after
8349MDS ~2.6 ~2.2
8360MDS ~2.8 ~2.6
8313RDB ~2.5 ~2.3 #nand boot
837xRDB ~3.1 ~2.3
also tested on an 8323ERDB.
v2: also remove the delayed icache enablement assumption in arch ppc's
board.c, and add a CONFIG_MPC83xx define in the ITX config file for
consistency (even though it was already being defined in 83xx'
config.mk).
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
and avoid e.g., two identical boards from causing random networking
conflicts when hooked up to the same network.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
There is more and more usage of printing 64bit values,
so enable this feature generally, and delete the
CONFIG_SYS_64BIT_VSPRINTF and CONFIG_SYS_64BIT_STRTOUL
defines.
Signed-off-by: Heiko Schocher <hs@denx.de>
some LCRR bits are not documented throughout the 83xx family RMs.
New board porters copying similar board configurations might omit
setting e.g., DBYP since it was not documented in their SoC's RM.
Prevent them bricking their board by retaining power on reset values
in bit fields that the board porter doesn't explicitly configure
via CONFIG_SYS_<registername>_<bitfield> assignments in the board
config file.
also move LCRR assignment to cpu_init_r[am] to help ensure no
transactions are being executed via the local bus while CLKDIV is being
modified.
also start to use i/o accessors.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
linux mpc83xx_defconfig kernels are getting bigger, accommodate for
their growth by adjusting default load and fdt addresses.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
when using Linus' 83xx_defconfig, the mpc8377rdb would hang at boot
at either:
NET: Registered protocol family 16
or the
io scheduler cfq registered
message. Fixing up these DDR settings appears to fix the problem.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
This patch adds support for eSDHC on MPC837XERDB boards. The WP
switch doesn't seem to work on RDB boards though, the WP pin is
always asserted (can see the pin state when it's in GPIO mode).
FSL DR USB and FSL eSDHC are mutually exclusive because of pins
multiplexing, so user should specify 'esdhc' or 'dr_usb' options
in the hwconfig environment variable to choose between the
devices.
p.s.
Now we're very close to a monitor len limit (196 bytes left using
gcc-4.2.0), so also increase the monitor len by one sector (64 KB).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Kim Phillips <kim.phillips@freescale.com>
Saving the environment leads to overwriting u-boot itself,
bricking boards. Increase u-boot's image size so the environment
base address doesn't end up overlapping u-boot text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the standard lowercase "x" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Use the standard lowercase "xx" capitalization that other Freescale
architectures use for CPU defines to prevent confusion and errors
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
On MPC8377E-RDB and MPC8378E-RDB boards we have PCIe and mini-PCIe
slots. Let's support them.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The CONFIG_CMD_ENV option controls enablement of the `saveenv` command
rather than a generic "env" command, or anything else related to the
environment. So, let's make sure the define is named accordingly.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Currently this is not creating any problem. But it will result
in compilation error when used as below.
printf("CFG_SDRAM_CFG2 - %08x\n", CFG_SDRAM_CFG2);
Signed-off-by: Selvamuthukumar <selva.muthukumar@e-coninfotech.com>
continuation of the theme based on git grep "^#define CFG_.*;$" include/
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
bootdelay set to -1 'permanently' disables autobooting, even if
bootcmd is specified. Change to a positive value to allow
autobooting when a bootcmd is set.
Reported-by: Coray Tate <Coray.Tate@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
the operating system may leave flash in a h/w locked state after writing.
This allows u-boot to continue to write flash by enabling h/w unlocking
by default.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Change all code that conditionally operates on high bat
registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS
instead of the myriad ways this is done now. Define the option
for every config for which high bats are supported (and
enabled by early boot, on parts where they're not always
enabled)
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
this seems as a good compromise between human memory, typing,
and last but not least, to accommodate for current and future kernel bloat.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Acked-by: Dave Liu <daveliu@freescale.com>
Currently the SATA controller clock is configured as CSB clock,
usually the CSB clock is 400/333/266MHz.
However, The SATA IP block is only guaranteed to operate up to
200 MHz as stated in the HW spec.
The bug is reported by Joe D'Abbraccio <ljd015@freescale.com>
This patch makes the SATA clock as half of CSB clock.
Signed-off-by: Dave Liu <daveliu@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Linux understands "host" (default), "peripheral" and "otg" (broken).
Though, U-Boot doesn't restrict dr_mode variable to these values (think
of renames in future).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
The device trees for these boards describe PCI I/O as starting from
address zero from the device's perspective.
Placing I/O elsewhere may cause problems with certain PCI boards, and may
cause problems with Linux.
Signed-off-by: Scott Wood <scottwood@freescale.com>
On the MPC8377ERDB: 2 SATA and 2 PCI-E.
On the MPC8378ERDB: 2 PCI-E
On the MPC8379ERDB: 4 SATA
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Update the MPC8349E-mITX, MPC8313E-RDB, and MPC837XE-RDB board files to upload
the Vitesse VSC7385 firmware. Changed CONFIG_VSC7385 to CONFIG_VSC7385_ENET.
Cleaned up the board header files to make selecting the VSC7385 easier to
control.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
the dts file basenames were updated in linux - this helps avoid
inadvertently loading any old dtbs laying around.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
MPC837xERDB board support includes:
* DDR2 330MHz hardcoded (soldered on the board)
* Local Bus NOR Flash
* I2C, UART and RTC
* eTSEC RGMII (TSEC0 - RTL8211B with MII;
* TSEC1 - VSC7385 local bus, hardcoded, requires seperate firmware
* load)
Signed-off-by: Kevin Lam <kevin.lam@freescale.com>
Signed-off-by: Joe D'Abbraccio <joe.d'abbraccio@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
