The gdsys strider board is based on a Freescale MPC8308 SOC.
It boots from NOR-Flash, kernel and rootfs are stored on
SD-Card.
On board peripherals include:
- 1x 10/100 Mbit/s Ethernet (optional)
- Lattice ECP3 FPGA connected via eLBC
Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
[trini: Drop setting CONFIG_SYS_GENERIC_BOARD, this is always true now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Fix below compilation warnings-
drivers/gpio/hi6220_gpio.c: In function ‘hi6220_gpio_probe’:
drivers/gpio/hi6220_gpio.c:82:15: warning: cast to pointer from integer
of different size [-Wint-to-pointer-cast]
bank->base = (u8 *)plat->base;
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Add 10m50 devboard support. It is based on the Golden Hardware
Reference Design (GHRD), available at,
http://rocketboards.org/foswiki/view/Documentation/
AlteraMAX1010M50RevCDevelopmentKitLinuxSetup
Though we supported only one nios2-generic board in the past. Now,
with the removal of the nios2-generic board dir, adding new nios2
boards to u-boot is easier than before. It should be helpful to
add those boards supported in Linux mainline. There are only two
such nios2 boards, the 3c120 devboard and 10m50 devboard. The
nios2-generic is actually 3c120, and should restore the name. The
10m50 is this one.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
The latest Linux can directly handle SMP operations for UniPhier SoCs
without any help of U-boot. Drop the relevant code from U-boot.
See commit b1e4006aeda8c8784029de17d47987c21ea75f6d ("ARM: uniphier:
rework SMP operations to use trampoline code") in Linux Kernel.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This makes USB3.0 available on new SoCs/boards.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The IRQ is not used in U-Boot, but this would be useful to sync
device trees between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This sets up a fine-grained page table, which is a requirement for
noncached_init() to operate correctly.
MMU setup code currently exists in a number of places:
- A version in the core ARMv8 support code that sets up page tables that
use very large block sizes that CONFIG_SYS_NONCACHED_MEMORY doesn't
support.
- Enhanced versions for fsl-lsch3 and zynmq that set up finer grained
page tables.
Ideally, rather than duplicating the MMU setup code yet again this patch
would instead consolidate all the different routines into the core ARMv8
code so that it supported all use-cases. However, this will require
significant effort since there appear to be a number of discrepancies[1]
between different versions of the code, and between the defines/values by
some copies of the MMU setup code use and the architectural MMU
documentation. Some reverse engineering will be required to determine the
intent of the current code.
[1] For example, in the core ARMv8 MMU setup code, three defines named
TCR_EL[123]_IPS_BITS exist, but only one of them sets the IPS field and
the others set a different field (T1SZ) in the page tables. As far as I
can tell so far, there should be no need to set different values per
exception level nor to modify the T1SZ field at all, since TTBR1 shouldn't
be enabled anyway. Another example is inconsistent values for *_VA_BITS
between the current core ARMv8 MMU setup code and the various SoC-
specific MMU setup code. Another example is that asm/armv8/mmu.h's value
for SECTION_SHIFT doesn't match asm/system.h's MMU_SECTION_SHIFT;
research is needed to determine which code relies on which of those
values and why, and whether fixing the incorrect value will cause any
regression.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
In order for noncached_init() to operate correctly, SoCs must set up a
custom page table with fine-grained (2MiB) sections, which can be
configured from noncached_init().
This is currently performed by arch/arm/cpu/armv8/{fsl-lsch3,zynqmp}/cpu.c
by cut/pasting and re-implementing mmu_setup, enable_caches(), etc. There
are some other reasons for the duplication there though, such as enabling
icache early, and enabling dcaching earlier with a different configuration.
This change makes mmu_setup() a weak implementation, so that the MMU setup
code can be replaced without having to duplicate other code that calls it.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The implementation of noncached_init() uses define MMU_SECTION_SIZE.
Define this on ARM64.
Move the prototype of noncached_{init,alloc}() to a location that
doesn't depend on !defined(CONFIG_ARM64).
Note that noncached_init() calls mmu_set_region_dcache_behaviour() which
relies on something having set up translation tables with 2MB block size.
The core ARMv8 MMU setup code does not do this by default, but currently
relies on SoC specific MMU setup code. Be aware of this before enabling
this feature on your platform!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Old sector number is not being cleared from FLASH_CR register. For example
when first erased sector was 001 and then you want to erase sector 010,
sector 011 gets erased instead.
This patch clears old sector number from FLASH_CR register before a new
one is written.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
flash_lock call is inside a for loop, so after the first iteration flash
is locked and no more sectors can be erased.
Move flash_lock out of the loop.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
In 522b021 we dropped 'PROVIDE(_GLOBAL_OFFSET_TABLE_ = . + 4)' lines in
the mpc85xx linker scripts as this is not required and breaks newer
binutils. This commit cleans up the rest of the powerpc linker scripts.
Signed-off-by: Tom Rini <trini@konsulko.com>
After consulting with some of the SPDX team, the conclusion is that
Makefiles are worth adding SPDX-License-Identifier tags too, and most of
ours have one. This adds tags to ones that lack them and converts a few
that had full (or in one case, very partial) license blobs into the
equivalent tag.
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Revert commit 7a2c1b13 which dropped OpenRD boards.
Assume maintainership of OpenRD.
Remove OpenRD from scrapyard.
Switch OpenRD to generic board.
Switch to Thumb build.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
Kirkwood files cpu.c and cache.c cannot build in Thumb state;
force them in ARM state even under CONFIG_SYS_THUMB_BUILD.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
When building a Thumb-1-only target with CONFIG_SYS_THUMB_BUILD,
some files fail to build, most of the time because they include
mcr instructions, which only exist for Thumb-2.
This patch introduces a Kconfig option CONFIG_THUMB2 and uses
it to select between Thumb-2 and ARM mode for the aforementioned
files.
Signed-off-by: Albert ARIBAUD <albert.u.boot@aribaud.net>
This patch fixes compile warnings like this:
warning: format '%lu' expects argument of type 'long unsigned int',
but argument 5 has type 'size_t'
In C99 standard you can use %zu modifier to print size_t values.
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
If you enable CONFIG_SEMIHOSTING for STM32F429 target, you will get compile
error looking like this:
arch/arm/lib/semihosting.c: In function 'smh_read':
{standard input}: Assembler messages:
{standard input}:34: Error: invalid swi expression
{standard input}:34: Error: value of 1193046 too large for field of 2 bytes at 0
scripts/Makefile.build:277: recipe for target 'arch/arm/lib/semihosting.o' failed
The source of the problem is "svc #0x123456" instruction. This instruction
can not be encoded using Thumb2 instruction set used by ARMv7M CPUs.
ARM documentation suggests using "bkpt #0xAB" instruction instead [1].
This patch fixes compile errors and adds support for semihosting for
STM32F429 or any other ARMv7M target.
This change was sested on STM32F429-DISCOVERY board using OpenOCD and
"smhload" u-boot command.
[1] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0471c/Bgbjhiea.html
Signed-off-by: Vadzim Dambrouski <pftbest@gmail.com>
In binutils-2.25, the _GLOBAL_OFFSET_TABLE_ symbols defined by PROVIDE in
u-boot.lds overrides the linker built-in symbols
(https://sourceware.org/git/gitweb.cgi?p=binutils-gdb.git;a=commitdiff;
h=b893397a4b1316610f49819344817715e4305de9),
so the linker is treating _GLOBAL_OFFSET_TABLE_ as a definition into the
.reloc section.
To align with the change of binutils-2.25, the _GLOBAL_OFFSET_TABLE_ symbol
should not be defined in sections, and the symbols in linker generated .got
section should be used(https://sourceware.org/ml/binutils/2008-09/
msg00122.html)
Fixed the following build errors with binutils-2.25:
| powerpc-poky-linux-gnuspe-ld.bfd: _GLOBAL_OFFSET_TABLE_ not defined in
linker created .got
Signed-off-by: Zhenhua Luo <zhenhua.luo@freescale.com>
Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
A number of headers define functions as "extern inline" which is
causing problems with gcc5. The reason is that starting with
version 5.1, gcc defaults to the standard C99 semantics for the
inline keyword.
Under the traditional GNU inline semantics, an "extern inline"
function would never create an external definition, the same
as inline *without* extern in C99. In C99, and "extern inline"
definition is simply an external definition with an inline hint.
In short, the meanings of inline with and without extern are
swapped between GNU and C99.
The upshot is that all these definitions in header files create
an external definition wherever those headers are included,
resulting in multiple definition errors at link time.
Changing all these functions to "static inline" fixes the problem
since this works as desired in all gcc versions. Although the
semantics are slightly different (a static inline definition may
result in an actual function being emitted), it works as intended
in practice.
This patch also removes extern prototype declarations for the
changed functions where they existed.
Signed-off-by: Mans Rullgard <mans@mansr.com>
This patch fix compilation error:
drivers/mmc/zynq_sdhci.c:16:5: error: conflicting types for
‘zynq_sdhci_init’
int zynq_sdhci_init(phys_addr_t regbase)
^
In file included from drivers/mmc/zynq_sdhci.c:14:0:
./arch/arm/include/asm/arch/sys_proto.h:16:5: note: previous declaration
of ‘zynq_sdhci_init’ was here
int zynq_sdhci_init(unsigned long regbase);
^
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The move to 'generic board' as well as changes in the generic
bootm code broke the boot of FIT uImage's. Especially uImage's
with additional initramfs images or FDT's do not work anymore.
Refactor the bootm code to work again with the generic bootm code.
Always relocate ramdisk and FDT in step 'bootm prep' because the
generic bootm code does this only for legacy uImage's.
Move the step 'bootm cmdline' to 'bootm prep' because the Linux
kernel parameters rd_start and rd_size have to be initialized after
the relocation of the ramdisk.
Furthermore support the step 'bootm fake'.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As the generic board runs in cached mode, it should not use
"stwio" which bypass the cache.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Chin Liang See <clsee@altera.com>
Remove CONFIG_SYS_INIT_SP macro, as the initial stack is set to
below the u-boot code.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Chin Liang See <clsee@altera.com>
As virt_to_phys() is used a lot in DMA transfer, change it
to use physaddr_mask in global data. This will save an "if"
statement and get a little faster.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Remove the useless parenthesis in asm/io.h as suggested
by Marek.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Acked-by: Marek Vasut <marex@denx.de>
Remove __ilog2_u64 and ffs4 from powerpc bitops to align with the
kernel implementation.
Use the generic __ffs64 instead of a custom powerpc implementation.
Cc: York Sun <yorksun@freescale.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Thomas Chou <thomas@wytron.com.tw>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Use the generic bitops and also add custom __ffs() implementation
as per the kernel.
Also align the ffs() implementation with the kernel.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
The generic bitops headers are required when calling logarithmic
functions, such as ilog2().
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
