The io setting are updated after some bugfix in different rk3399 boards,
sync the code from vendor.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Update lpddr timing in lpddr4-400 and lpddr4-800 file from rockchip
vendor code;
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add capacity detect for rk3399 so that the driver able to detect the
capacity automatically.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Clean up the sdram_init to keep sync with rockchip source code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Clean up rk3399 dram driver source code for more readable.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
For there are some structures and functions are common for all rockchip SoCs,
migrate to use the common code so that we can clean up reduandent codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
RK3328 has a similar controller and phy with PX30, so we can use the
common driver for it and remove the duplicate codes.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Add the sdram driver for PX30 to support ddr3, ddr4, lpddr2 and lpddr3.
For TPL_BUILD, the driver implement full dram init and without DM
support due to the limit of internal SRAM size.
For SPL and U-Boot proper, it's a simple driver with dm for get
dram_info like other SoCs.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The noc register bit definition may be the same for different SoC while
the offset of the register may be different, add the struction
definition as common code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_phy_px30.c is based on PX30 SoC, the functions are common
for phy, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
This sdram_pctl_px30.c is based on PX30 SoC, the functions are common
for controller, other SoCs with similar hardware could re-use it.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The debug info for dram is main about the capacity related info which is
very important the board init, so set this default enable.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The functions for dram info print are part of common code.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
There are some function like os_reg setting, capacity detect functions,
can be used as common code for different Rockchip SoCs, add a
sdram_common.c for all these functions.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We are using sys_reg2 and sys_reg3 as ddr cap info, sync the variable
name to what we real use to avoid confuse people.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Since we have new DRAM type and to support different DRAM size in different
CS, we need more bits, so introduce sys_reg3 to record the info.
Note that the info in sys_reg3 is extension to sys_reg2 and the info in
sys_reg2 is the same as before. We define the DRAM_INFO with sys_reg3 as
VERSION2.
All the ENC macro are moved to sdram_common.h since the sdram.c only
need to do the info decode.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The sdram.h suppose to be helper file for sdram.c which including dram
size decode and some u-boot related dram init interface, and all
structure and function for dram driver move to sdram_common.h
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
rename sdram_common.c in arch/arm/mach-rockchip to sdram.c;
so that we can use the file name sdram_common.c in dram driver for
better understand the code;
clean the related file who has use the header file at the same time.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
The header file sdram.h is used for rk3288 and similar SoCs, rename it
to make it more understandable.
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
- Migrate the symbol CONFIG_SYS_REDUNDAND_ENVIRONMENT to Kconfig. This
is size neutral outside of two platforms with latent bugs being fixed
now and they no longer have "ENV_IS_NOWHERE" set along with their
intended location.
Move this symbol to Kconfig. As part of this we can drop a UBI-specific
symbol that was a stop-gap for not having this particular symbol in
Kconfig.
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is setting CONFIG_ENV_IS_IN_SPI_FLASH in the header rather
than defconfig, fix.
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
This board is setting CONFIG_ENV_IS_IN_MMC in the header rather than
defconfig, fix.
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
-----BEGIN PGP SIGNATURE-----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=sgCz
-----END PGP SIGNATURE-----
Merge tag 'u-boot-imx-20191105' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx
u-boot-imx-20191105
-------------------
i.MX8MN SoC support
ROM API image download support
i.MX8MM enet enabling
With recent update in u-boot gitattributes all files are treated as regular
text files. This creates problems with special files and repo always
shows uncommitted files like below.
Your branch is up-to-date with 'origin/master'.
Changes not staged for commit:
(use "git add <file>..." to update what will be committed)
(use "git checkout -- <file>..." to discard changes in working directory)
modified: tools/logos/compulab.bmp
modified: tools/logos/denx-comp.bmp
modified: tools/logos/toradex.bmp
To fix above problem special files bmp/ttf files are treated as binary
files in the gitattributes.
Signed-off-by: Vignesh Rajendran <vignesh.rajendran@in.bosch.com>
Signed-off-by: Veeraiyan Chidambaram <veeraiyan.chidambaram@in.bosch.com>
The generated idbloader.img file that rockchip uses should
be not included in git status report
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
A recent change adjusted the symbol calculation to work on x86 but broke
it for Tegra. In fact this is because they have different needs.
On x86 devices the code is linked to a ROM address and the end-at-4gb
property is used for the image. In this case there is no need to add the
base address of the image, since the base address is already built into
the offset and image-pos properties.
On other devices we must add the base address since the offsets start at
zero.
In addition the base address is currently added to the 'offset' and 'size'
values. It should in fact only be added to 'image-pos', since 'offset' is
relative to its parent and 'size' is not actually an address. This code
should have been adjusted when support for 'image-pos' and 'size' was
added, but it was not.
To correct these problems:
- move the code that handles adding the base address to section.py, which
can check the end-at-4gb property and which property
(offset/size/image-pos) is being read
- add the base address only when needed (only for image-pos and not if the
image uses end-at-4gb)
- add a note to the documentation
- add a separate test to cover x86 behaviour
Fixes: 15c981cc (binman: Correct symbol calculation with non-zero image base)
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
- Add support for rockchip pmic rk805,rk809, rk816, rk817
- Add rk3399 board Leez support
- Fix bug in rk3328 ram driver
- Adapt SPL to support ATF bl31 with entry at 0x40000
- Fix the u8 type comparision with '-1'.
- Fix checkpatch warning for multi blank line and review signature.
This patch enable TPL support for firefly-rk3288 board, which works ths
same way with other RK3288 board like Tinker, evb.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Without the prefix, "same-as-spl" in `u-boot,spl-boot-order` will not work
as expected. When board_boot_order() `spl-boot-order.c` meets
"same-as-spl", it gets the conf by looking the boot_devices table by boot
source, and parse the node by the conf with:
node = fdt_path_offset(blob, conf);
which will failed without the "/" indicating the path.
Currently only entries of boot_devices in rk3399 have the "/" prefix.
Therefore add the missing ones in other boards.
Signed-off-by: Levin Du <djw@t-chip.com.cn>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since we move the ATF bl31 entry for 64bit CPUs to 0x40000, we need to
limit the SPL size in 0x40000(start from 0) so that we don't need to do
the relocate for ATF loading.
Note that there will be separate BSS, STACK and MALLOC heap, so the size
0x40000(256KB) should be enough for SPL text.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Use the same SPL_STACK_R_ADDR in Kconfig instead of each board config;
default to 0x4000000(64MB) instead of 0x80000(512KB) for this address
can support all the SoCs including those may have only 64MB memory, and
also reserve enough space for atf, kernel(in falcon mode) loading.
After the ATF entry move to 0x40000, the stack from 0x80000 may be override
when loading ATF bl31.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.
Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.
The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.
Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.
The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
We use to reserve IRAM to avoid the SPL text overlap with ATF M0 code,
and when we introduce the TPL, the SPL space is in DRAM, we reserve
space to avoid SPL text overlap with ATF bl31.
Now we decide to move ATF entry point to 0x40000 instead of 0x1000,
so that the SPL can have 0x4000 as code size and no need to reserve
space or relocate before loading ATF.
The mainline ATF has update since:
0aad563c rockchip: Update BL31_BASE to 0x40000
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Trusted-Firmware can also initialize a secure payload to use as a trusted
execution environment. In general for the arm64 case this is provided as
separate image and uboot is supposed to also place it in a predetermined
location in memory and add the necessary parameters to the ATF boot params.
So add the possibility to get this tee payload from the provided FIT image
and setup things as necessary.
Tested on a Rockchip PX30 with mainline TF-A, mainline OP-Tee (with pending
PX30 support) and mainline 5.4-rc1 Linux kernel.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
A trusted execution environment should also get loaded as loadable from
a fit image, so add the possibility to present a tee.elf to make_fit_atf.py
that then gets included as additional loadable into the generated its.
For ease of integration the additional loadable is created as atf_(x+1)
after all others to re-use core generation loops.
Tested against the combinations of 1-part-atf and multi-part-atf each
time with and without a tee binary present.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix a typo that caused incorrect values to be loaded into the DRAM
controller's deskew registers.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Fix a pair of tests in phy_dll_bypass_set() that used incorrect units
for the DDR frequency, causing the DRAM controller to be misconfigured
in most cases.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
rk3328 can use same-as-spl option so next loaders are loaded from the same
medium.
Add the boot order in the rock64 dts otherwise booting from sdcard
will result in u-boot looking into the eMMC.
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Reviewed-by: Peter Robinson <pbrobinson@gmail.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add a call to rk3328_configure_cpu() during initialization to set the
CPU-clock frequency.
Signed-off-by: Simon South <simon@simonsouth.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Specification
- Rockchip RK3399
- LPDDR4
- TF sd scard slot
- eMMC
- M.2 B-Key for 4G LTE
- AP6256 for WiFi + BT
- Gigabit ethernet
- HDMI out
- 40 pin header
- USB 2.0 x 2
- USB 3.0 x 1
- USB 3.0 Type-C x 1
- TYPE-C Power supply
Commit details of rk3399-leez-p710.dts sync from linus tree for Linux 5.4-rc1:
"arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC"
(sha1: fc702ed49a8668a17343811ee28214d845bfc5e6)
Signed-off-by: Andy Yan <andyshrk@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK809 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(5*BUCKs, 9*LDOs, 2*SWITCHes)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK817 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1* BOOST, 9*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK805 are a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 3*LDOs)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The RK816 is a Power Management IC (PMIC) for multimedia
and handheld devices. They contains the following components:
- Regulators(4*BUCKs, 1*BOOST, 6*LDOs, 1*SWITCH)
- RTC
- Clocking
Signed-off-by: Elaine Zhang <zhangqing@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
