IFC-NOR and QSPI-NOR pins are multiplexed on SoC, so they cannot be
accessed simultaneously. IFC-NOR can be accessed along with SD-BOOT.
Ls1088aqds_sdcard_ifc_defconfig is default config for SD boot and
IFC-NOR to be used as flash. This allows writing to IFC-NOR flash.
QSPI and DSPI cannot be accessed in this defconfig.
IFC-NOR image is generated using ls1088aqds_defconfig.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This function is required for enabling access to early i2c function
for correct usage of QIXIS_READ and QIXIS_WRITE.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
get_board_ddr_clk(), get_board_sys_clk() and if_board_diff_clk() is
now available for SPL build.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add first support for STM32MP157C-ED1 board with "Basic" boot chain
1/ Boot Rom: load SPL with STM32 image header in SYSRAM
2/ SPL: power up and initialize the DDR and load U-Boot image
from SDCARD in DDR
3/ U-Boot: search and load extlinux.conf in SDCARD
(DISTRO activated)
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Support several pixel format (8bits, 16bits, 24bits & 32bits).
Add new file st_logo_data.h which contains logo
stmicroelectronics_uboot_logo_8bit_rle.bmp.
Signed-off-by: yannick fertre <yannick.fertre@st.com>
This converts the following to Kconfig:
CONFIG_CONS_INDEX
We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.
Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>
It is safe to always setup the pinmux for UART1 and UART3 to be used in
early_padconf and then if these pins are needed later on, they will be
re-muxed. This allows us to drop the usage of CONFIG_CONS_INDEX here.
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
serial# variable is needed to show the device correctly in "fastboot
devices" output. It's useful when we have several devices (in fastboot
mode) connected to single host and want to choose which one to flash.
We can't use omap_die_id_serial() for this, because AM335x lacks
DIE_ID, as can be seen from AM335x TRM. Let's do next:
- reuse board_serial variable (obtained from EEPROM in
set_board_info_env() function) to set serial#
- if board_serial is "unknown", reuse ethaddr variable to set serial#
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard 'xM' does not really have NAND. CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT can/should be empty for 'xM'. This commit sets
the defined values if they exist.
Signed-off-by: Derald D. Woods <woods.technical@gmail.com>
Remove arch/arm/include/asm/arch-stm32fx/stm32_periph.h
as all defines or enums are no more used.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Use available DM stm32_timer driver instead of dedicated
mach-stm32/stm32fx/timer.c.
Remove all defines or files previously used for timer usage in
arch/arm/include/asm/arch-stm32fx and in arch/arm/mach-stm32/stm32fx
Enable DM STM32_TIMER for STM32F4/F7 and H7.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
RK3288 Vyasa has eMMC boot support, with JP4 open.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Sync rk3288-vyasa board dts from Linux for proper updates and maintenance
- rk3288-vyasa.dts: Similar to Linux dts
- rk3288-vyasa-u-boot.dtsi: u-boot dts changes
Also updated MAINTAINERS for these dts files.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
A20-SOM204 board has option with onboard 16GB eMMC. The chip is wired
to MMC2 slot.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This is new System-On-Module platform with universal dimm socket for
easy insertation. The EVB board is designed to be universal with
future modules.
Base features of A20-SOM204 board includes:
* 1GB DDR3 RAM
* AXP209 PMU
* KSZ9031 Gigabit PHY
* AT24C16 EEPROM
* Status LED
* LCD connector
* GPIO connector
There will be variants with the following options:
* Second LAN8710A Megabit PHY
* 16MB SPI Flash memory
* eMMC card
* ATECC508 crypto device
The EVB board has:
* Debug UART
* MicroSD card connector
* USB-OTG connector
* Two USB host
* RTL8723BS WiFi/BT combo
* IrDA transceiver/receiver
* HDMI connector
* VGA connector
* Megabit ethernet transceiver
* Gigabit ethernet transceiver
* SATA connector
* CAN driver
* CSI camera
* MIC and HP connectors
* PCIe x4 connector
* USB3 connector
* Two UEXT connectors
* Two user LEDs
Some of the features are multiplexed and cannot be used the same time:
CAN and Megabit PHY. Others are not usable with A20 SoC: PCIe and USB3.
This patch adds defconfig and dts files for this board. The dts is same
with mainline kernel, except some nodes are removed to make file
compatible with existing dtsi file.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
In README.sunxi64 we tell the user how to optionally create
u-boot-sunxi-with-spl.bin by manually running cat. Instead, have the
build system create the file automatically just like it does for 32-bit
sunxi boards.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
The @gdsys.cc addresses are supposed to be used for mailing lists.
Switch all occurrences of @gdsys.de mail addresses to their @gdsys.cc
equivalent.
Also, Dirk's address was wrong in one place; fix that as well.
Signed-off-by: Mario Six <six@gdsys.cc>
Thomas reported U-Boot failed to build host tools if libfdt-devel
package is installed because tools include libfdt headers from
/usr/include/ instead of using internal ones.
This commit moves the header code:
include/libfdt.h -> include/linux/libfdt.h
include/libfdt_env.h -> include/linux/libfdt_env.h
and replaces include directives:
#include <libfdt.h> -> #include <linux/libfdt.h>
#include <libfdt_env.h> -> #include <linux/libfdt_env.h>
Reported-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Rename CONFIG_SPL_USBETH_SUPPORT to CONFIG_SPL_USB_ETHER.
This enables users to block text using CONFIG_IS_ENABLED() instead
of resorting to #if ladders with SPL and non-SPL cases.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Add R8A77965 M3N Salvator-XS development kit support. This kit is
similar to the other Salvator-X(S) ones, except is has M3N SoC on
it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Add support for a new boards from devboards.de , the DBM-SoC1 .
This board has one ethernet port, one USB OTG port and USB UART.
Signed-off-by: Marek Vasut <marex@denx.de>
This seems to have been missed, possibly due to the inability to
enable TI_SECURE_DEVICE on Keystone2 devices previously.
Fixes: bfebc8c965 ("env: Rename getenv_hex(), getenv_yesno(), getenv_ulong()")
Signed-off-by: Andrew F. Davis <afd@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Currently SPL_LOAD_FIT is unable to boot from nand on
i.MX6QDL platform, so enable only for MMC boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Engicam Is.IoT has eMMC and NAND cpu modules where MMC
is common for both, so remove explicit mmc defconfig.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
This reverts commit edf0093732 for
cm_fx6 iMX.6 Solo module as it causes frequent (around 10 percent of
power cycles) board's hangs.
These hangs happen in SPL when BSS is being initialized in SDRAM -
it appear that variables from BSS contain trash values which lead to board
hangs. Looks like that SDRAM doesn't yet finish initialization in these
cases.
Signed-off-by: Maxim Yu. Osipov <mosipov@ilbers.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Do the following to make the symbol names less confusing.
sed -i "s/\([TU][^_]\+\)_FUNCTION_DFU/DFU_OVER_\1/g" \
`git grep _FUNCTION_DFU | cut -d ":" -f 1 | sort -u`
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Lukasz Majewski <lukma@denx.de>
These ARM boards are in nice shape and still being used a lot
with e.g. QEMU, so I can maintain them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since DRA7xx/AM57xx SR1.1 and SR1.0 has errata to limit the frequency of
MMC1 to 96MHz and frequency of MMC2 to 48MHz for AM572x SR1.1, limit the
frequency and disable higher speed modes for those revision.
Also use the recommended IO delays (those tagged with "rev11")
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
To debug device tree issues involving 32- and 64-bit platforms, it is useful to
have a generic 64-bit platform available.
Add a version of the sandbox that uses 64-bit integers for its physical
addresses as well as a modified device tree.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Added CONFIG_SYS_TEXT_BASE to configs/sandbox64_defconfig
Signed-off-by: Simon Glass <sjg@chromium.org>
The 'reset' command did not work on Porter because the reset code
was accessing the wrong PMIC address over broken I2C bus driver.
Replace the code with DM-aware code and fix up the PMIC address.
This makes the 'reset' command work again.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Toggle the PHY reset GPIO to bring the ethernet PHY out of reset properly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: This should be moved to the SH ethernet driver, but it's quite
late in the cycle, so this is something to be done in 2018.05.
Due to size limitations of the MERAM, switch U-Boot to SPL.
The SPL is loaded by the SPI_LOADER into MERAM and then loads
U-Boot proper into DRAM. This way U-Boot can freely grow in
size in DRAM, as there is plenty of it.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
---
NOTE: To update U-Boot, first install u-boot.img to 0x140000 in SPI NOR,
then use the Minimon to flash u-boot-spl.srec using ls,2,e6304000.
To generate u-boot-spl.srec, use objcopy:
arm-linux-gnueabi-objcopy -O srec spl/u-boot-spl u-boot-spl.srec
Commit 958d55f26c ("MAINTAINERS: Take over BCM2835 maintainership") put
me in as maintainer for the RPi soc, but forgot to update the board
MAINTAINERS file.
Add me there too.
Signed-off-by: Alexander Graf <agraf@suse.de>
board_usb_init()/_cleanup() should be in board files and don't have
a place in the xhci-omap driver. Weak versions for
board_usb_init()/_cleanup() already exist in common/usb.c
(for host mode) and drivers/usb/gadget/g_dnl.c (for gadget mode).
Therefore, remove init and cleanup functions from xhci-omap and
implement them in the board files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
There is no EMMC symbol in the "enable different boot versions for the
shc board" choice. SHC_EMMC was probably intended.
No functional changes. Kconfig choices fall back on using the first
(visible) symbol in the choice as the default if the default symbol is
not visible.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which prints the following warning:
warning: the default selection EMMC (undefined) of <choice> (defined at board/bosch/shc/Kconfig:15) is not contained in the choice
I've added a corresponding warning to the C tools too, which is
currently in linux-next: https://patchwork.kernel.org/patch/9983667/
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
The initial implementation of mx6memcal reset the CPU after
running the memory calibration procedure because the generic
board has no information about which boot devices are available.
Now that we have SDP support in SPL, use it to allow a full
U-Boot to be uploaded (i.e. to use "mtest").
Signed-off-by: Eric Nelson <eric@nelint.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Static variables are not available during board_init_f().
'static uint32_t mx53_dram_size[2];' was used in board specific
dram_init(), dram_init_banksize() and get_effective_memsize() to avoid
multiple calls to get_ram_size().
Reused dram initialization functions from arch/arm/mach-imx/mx5/mx53_dram.c
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Move dram_init(), dram_init_banksize() and get_effective_memsize() to
arch/arm/mach-imx/mx5/mx53_dram.c, where it can be reused by m53evk and
mx53loco.
Signed-off-by: Patrick Bruenn <p.bruenn@beckhoff.com>
Validate the time at startup:
- in case rtc error add to kernel command line RTC_ERROR
- clamp date to 1-Jan-2036
Signed-off-by: Nandor Han <nandor.han@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Modify configuration to support FIT. Set variable `confidx' from VPD,
in order to load the correct device tree. Modify/simplify U-Boot
environment to support loading FIT image.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Enable the hardware watchdog on bx50v3 to cause it to reset in the event
the board hangs.
Configure GPIO_9 pin as WDOG1_B so that a watchdog timeout results in a
full system reset.
The watchdog is used and reconfigured by systemd approximately 1.7 seconds
into boot. Adding a few seconds for U-Boot and a few more seconds as a
safety margin.
Note that the PCIe controller is _not_ put back into a safe state prior
to board reset. This is a problem if board reset is implemented as CPU
reset.
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
There are two I210s on the b850v3 and one on the b450v3 and b650v3.
One is connected to Marvell 88e6240 which is already programmed.
Follow the flow documented in doc/README.enetaddr: set the
enet[0-9]*addr environment variable and let the driver program the
hardware.
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order.
The environment variables are removed after programming the hardware
because the variables seem to influence MAC addresses also after U-Boot.
Specifically the MAC address of FEC (MC interface) would be incorrectly
set: 'ethaddr', which maps to the first I210 chip and is set to I210's
default address read from the driver by eth_write_hwaddr in eth_legacy.c
because the variable is undefined (not set even by bx50v3.c), would
result in the eth0 interface's MAC address to be set to I210's default
address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Instead of programming the hardware directly in the board
implementation, follow the flow documented in doc/README.enetaddr: set
the enet[0-9]*addr environment variable and let the driver program the
hardware.
This avoids duplicating the implementation as it already exists in the
driver (drivers/net/fec_mxc.c: fec_set_hwaddr).
The mapping from the driver's index to the environment variable's name
is documented in README: Note for Redundant Ethernet Interfaces. It is
assumed that eth_devices for the controllers on the board are always
indexed in the same order, i.e. FEC always has the index 2.
The FEC driver does *not* set the flag Set MAC Address on Transmit (bit
set_eth0_mac_address used to do but this is unnecessary as the Linux
networking stack fills in the MAC address.
Signed-off-by: Hannu Lounento <hannu.lounento@ge.com>
Signed-off-by: Ian Ray <ian.ray@ge.com>
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The change in i2c configuration added to support access to the VPD has
inadvertantly caused access to i2c buses 1 & 2 to be lost. This has
resulted in the configuration for the PMIC to be attempted on the wrong
bus and thus isn't taking effect.
Add the required configuration to return access to buses 1 & 2. In order
to ensure that any users of the bus numbering prior to addition in VPD
patches work, add buses before configuration related to mux on bus 0 and
tweak VPD bus usage to fit new numbering scheme.
Signed-off-by: Martyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
i.CoreM6 1.5 is an another i.CoreM6 QDL cpu modules which can be connected
to EDIMM starter kit design with eMMC and MIPI-CSI interfaces suitable for
Android and video capture application.
notable features:
CPU NXP i.MX6 S/DL/D/Q, Up to 4 x Cortex-A9@800MHz
Memory Up to 2 GB DDR3-1066
Video Interfaces Up to 1 Parallel Up to 2 LVDS HDMI 1.4
port 8 bit CSI INPUT MIPI-CSI INPUT
1 x 10/100 Ethernet interface, 2 x USB, 1 x PCIe, 1 x I2S etc
This patch adds support for Quad/Dual and DualLite/Solo SOM's on
MIPI starter kit with boot from SD and eMMC.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlpxesoACgkQykllyylKDCFwngCfZfk2S+c9uJCLh1drA7a+J4Ch
G+MAnA/iRu6/Ihd5UMe4tMK8BU51h0GQ
=Ylul
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze
Xilinx changes for v2018.03
- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes
Tested with MTA72ASS8G72PSZ-2S6G1. This is 3DS RDIMM module with x4
DDR chips. LS2088ARDB needs to be modified to connect all DQS signals.
Some of them are grounded by default for x8 chips. Tested with RDIMM
MTA18ASF2G72PDZ on main memory controllers. DP-DDR doesn't support
RDIMM. Dropped related timing table.
Signed-off-by: York Sun <york.sun@nxp.com>
'select n' selects a constant symbol, which is meaningless and has no
effect. Maybe this was meant to be a 'default n', though bool and
tristate symbols already implicitly default to n.
Discovered in Kconfiglib (https://github.com/ulfalizer/Kconfiglib),
which does more strict checking here:
kconfiglib.KconfigSyntaxError: board/google/Kconfig:34: Couldn't parse ' select n': expected nonconstant symbol
Signed-off-by: Ulf Magnusson <ulfalizer@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Move generic functions to common location psu_spl_init.c. Function
declarations are added to private header.
These changes are done in connection to the fact that still files from
HDF can be copied over and compilation should pass.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Remove SPL_BUILD dependency from zynqmp.c and move it to header file.
Use only one symbol for including psu_init.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
psu_init() returns int which wasn't declared and checked.
The patch is fixing function declarations and code to handle return
values properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Add check if boot_targets exists in environment and then
generate new_targets env accordingly. Performing strlen on
null address causes it to fail with exception if isolation
is enabled with DDR address zero as secure. It works with out
isolation enabled as zero is valid address but it may lead to
junk values in boot_targets.
This patch fixes the issue by checking return value of env_get
so that it generate boot_targets properly.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zc770-xm011 is x8 width configuration. This FMC card has also x16
variant which requires different ps7_init configuration. This patch adds
it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
checkpatch.pl complains about the spelling of ERR_TIMOUT. Since the
error is only used in a handful of files, we rename the error to
ERR_TIMEOUT.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
The SOM has external pull-up resistors, so let's turn these off.
It was helping reduce some errors when running I2C1 @ 2.6MHz.
Signed-off-by: Adam Ford <aford173@gmail.com>
We are switching to a model where our board file can directly fail probing
of serial devices when they're not usable, so remove the current runtime
hack we have.
Signed-off-by: Alexander Graf <agraf@suse.de>
The bcm283x family of SoCs have a GPIO controller that also acts as
pinctrl controller.
This patch introduces a new pinctrl driver that can actually properly mux
devices into their device tree defined pin states and is now the primary
owner of the gpio device. The previous GPIO driver gets moved into a
subdevice of the pinctrl driver, bound to the same OF node.
That way whenever a device asks for pinctrl support, it gets it
automatically from the pinctrl driver and GPIO support is still available
in the normal command line phase.
Signed-off-by: Alexander Graf <agraf@suse.de>
If we include both the rk3288_grf.h and rv1108_grf.h, it will cause the
conflicts of redefinition. Clean the iomux definitions at grf_rv1108.h,
and move them into pinctrl-driver.
Signed-off-by: David Wu <david.wu@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
hw_data_init() is called before relocation to initialise hardware data.
Since ctrl is initialized to OMAP_SRAM_SCRATCH_SYS_CTRL in
arch/arm/mach-omap2/am33xx/hw_data.c, the pointer *ctrl will not be
updated during relocation and will hold a stale value.
Therefore call hw_data_init() again after relocation to
reinitialize *ctrl.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Move SYSCFG clock setup into configure_clocks() instead of calling
clock_setup() from board file.
As this clock is only needed in case of ethernet enabled and as
both stm32f4 and stm32f7 are using the Designware ethernet IP,
we use CONFIG_ETH_DESIGNWARE to only enable this clock if needed.
Move the RMII setup from board_early_init_f() to board_init()
to insure that RMII bit is set only when clock driver is initialized.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Thanks to 'commit ba1f966725 ("net: designware: add clock support")'
we don't need anymore to setup the STMMAC clock in board.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Convert the R8A7791 Porter board to DM and DT. This implies mostly
enabling the necessary configuration options and plucking out the
ad-hoc configuration from the board file. Moreover, the pre-reloc
malloc size was increased to allow the clock driver to start up
early without running out of malloc space and the early stack was
moved further up in the DRAM to avoid rewriting U-Boot itself.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The current environment has been hardcoded to an offset that starts to be
an issue given the current size of our main U-Boot binary.
By implementing a custom environment location routine, we can always favor
the FAT-based environment, and fallback to the MMC if we don't find
something in the FAT partition. We also implement the same order when
saving the environment, so that hopefully we can slowly migrate the users
over to FAT-based environment and away from the raw MMC one.
Eventually, and hopefully before we reach that limit again, we will have
most of our users using that setup, and we'll be able to retire the raw
environment, and gain more room for the U-Boot binary.
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
When flashing U-Boot on a Boston board using Xilinx Vivado tools, the
final 0x00 byte which ends the .relocs section seems to be skipped &
left in flash as 0xff unless the data contained in the .mcs is padded
out to a 16 byte boundary. Without our final zero byte relocation will
fail with an error about a spurious reloc:
Avoid this problem by padding out the data in the .mcs file to a 16 byte
boundary using srec_cat's -range-pad functionality.
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
wait_for_bit callers use the 32 bit LE version
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Currently only SD, NAND can be secondary boot sources controlled
by FPGA/CPLD via qixis commands. For SoC like LS1088 IFC-NOR
can be secondary boot source, while QSPI-NOR is the primary.
Add options in qixis to switch to other boot sources including
ifc and emmc.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Enables and compiles VID specific functions for SPL.
Signed-off-by: Pankit Garg <pankit.garg@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch adds the support for VID on LS1088AQDS and LS1088ARDB systems.
It reads the fusesr register and changes the VDD accordingly by adjusting
the voltage via LTC3882 regulator.
This patch also takes care of the special case of 0.9V VDD is present in
fusesr register. In that case,it also changes the SERDES voltage by
disabling the SERDES, changing the SVDD and then re-enabling SERDES.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Amrita Kumari <amrita.kumari@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a VID specific API in init_sequence_f and spl code flow
namely init_func_vid which is required to adjust core voltage.
VID specific code is required in spl, hence moving flag CONFIG_VID
out of spl flags.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
When VID feature is supported, check the contents of fuse register
and configure DDR operate at 0.9v.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Restructures common driver to support LTC3882 voltage regulator
chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Moves IR chip (IR36021) specific code in flag to resolve
compilation issue where it is not present. For example,
LS1088A is having a new LTC3882 voltage chip.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Adds a board specific API namely board_adjust_vdd which
is required to define the board VDD adjust settings.
Signed-off-by: Ashish Kumar <Ashish.Kumar@nxp.com>
Signed-off-by: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The SPL doesn't have much room, so in order to support OF_CONTROL
in SPL, we need the extra functionality of SPL_OF_PLATDATA.
Adding these features allows us to remove a small part of code without
losing the serial port during SPL.
Signed-off-by: Adam Ford <aford173@gmail.com>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_CYRUS
CONFIG_IDS8313
CONFIG_MPC8308_P1M
CONFIG_MPC8308RDB
CONFIG_MPC8349EMDS
CONFIG_MPC8349ITXGP
CONFIG_SBC8349
CONFIG_SBC8548
CONFIG_SBC8641D
CONFIG_TQM834X
CONFIG_VE8313
CONFIG_XPEDITE5140
CONFIG_XPEDITE5200
CONFIG_XPEDITE550X
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
Acked-by: Mario Six <mario.six@gdsys.cc>
The following config symbols are only defined once and never referenced
anywhere else:
CONFIG_AMCORE
CONFIG_ASTRO5373L
CONFIG_M52277EVB
CONFIG_M5253DEMO
CONFIG_M5253EVBE
CONFIG_M5275EVB
CONFIG_M54418TWR
CONFIG_STMARK2
Most of them are config symbols named after the respective boards which
seems to have been a standard practice at some point.
Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>
This adds support for '-machine virt' on AArch64. This is rather simple:
we just add TARGET_QEMU_ARM_xxBIT to select a few different Kconfig
symbols, provide the ARMv8 memory map from the board file and add a new
defconfig based on the 32-bit defconfig.
Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Reviewed-by: Tom Rini <trini@konsulko.com>
Update the board pinmux for AM574x-IDK board using latest PMT[1] and the
board files named am574x_idk_v1p3b_sr2p0 that were auto generated on
13th October, 2017 by "Ahmad Rashed <a-rashed@ti.com>".
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
AM574x-idk has the following DDR parts attached:
EMIF1: MT41K256M16HA (1GB with ECC)
EMIF2: MT41K256M16HA (1GB without ECC)
Enabling 2GB DDR without interleaving between EMIFs. And
enabling ECC on EMIF1.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Krunal Bhargav <k-bhargav@ti.com>
DRA762 comes in two packages:
- ABZ: Pin compatible package with DRA742 with DDR@1333MHz
- ACD: High performance(OPP_PLUS) package with new IPs
Both the above packages uses the same IDCODE hence needs to
differentiate using package information in DIE_ID_2.
Add support for the same. Also update clock, ddr, emif information.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
All ddr3_emif declarations are not used outside ddr3_k2g.c
file. So make all of them as static.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
gpio1_2 is used for HPD interrupt with DRA76's DVI add-on board, so mux
the pin as gpio and PIN_INPUT.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Added support for K2G EVM with FlipChip SoC of which
ARM/DDR3 runs at 1GHz/1066 MT/s. The patch is also
backward compatible with old revision EVM and EVM
with WireBond SoC. Their ARM/DDR3 run at 600MHz/800 MT/s.
The new SoC supports 2 different speeds at 1GHz and 600MHz.
Modyfied the CPU Name to show which SoC is used in the EVM.
Modified the DDR3 configuration to reflect New SoC supports
2 different CPU and DDR3 speeds, 1GHz/1066MT and 600MHz/800MT.
Added new inline function board_it_k2g_g1() for the new FlipChip 1GHz,
and set the u-boot env variable board_name accordingly.
Modified findfdt script in u-boot environment variable to include new k2g board type.
Signed-off-by: Rex Chang <rchang@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
MCAN can be accessed via DCAN1 or DCAN2. Determining which DCAN instance
to use if any at all is done through
CTRL_CORE_CONTROL_SPARE_RW.SEL_ALT_MCAN. Since general pinmuxing is
handled in U-boot. Handle this additional pinmuxing requirement in U-boot
to ensure that MCAN is used by default via the DCAN1 pins.
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
[fcooper@ti.com: Update commit message and use DCAN1 not DCAN2 for MCAN]
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Both the "qixis_reset" and esbc_validate" commands can only be used in
full U-Boot so do not build them in SPL. As part of this rework the
qixis code to declare things as static and make use of __weak for
function aliases.
Cc; York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
The DT spec demands a unit-address in a node name to match the "reg"
property in that node. Newer dtc versions will throw warnings if this is
not the case.
Adjust the FIT build script for 64-bit Allwinner boards to remove the
bogus addresses from the node names and avoid the warnings.
This avoids a warning with recent versions of the dtc tool.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
We dont need to keep copies of the properties that we are going to
fixup since we will be using the dtb provided by the firmware.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
The firmware that runs before u-boot modifies u-boot's device tree
adding the local-mac-address and local-bd-address properties for the
compatibles "qcom,wcnss-bt" and "qcom,wcnss-wlan".
This commit reads that firmware, retrieves the properties and fixups
the device tree that is passed to the kernel before booting.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
This commit adds support for 96Boards Dragonboard820C.
The board is based on APQ8086 Qualcomm Soc, complying with the
96Boards specification.
Features
- 4x Kyro CPU (64 bit) up to 2.15GHz
- USB2.0
- USB3.0
- ISP
- Qualcomm Hexagon DSP
- SD 3.0 (UHS-I)
- UFS 2.0
- Qualcomm Adreno 530 GPU
- GPS
- BT 4.2
- Wi-Fi 2.4GHz, 5GHz (802.11ac)
- PCIe 2.0
- MIPI-CSI, MIPI-DSI
- I2S
U-Boot boots chained from LK (LK implements the fastboot protocol) in
64-bit mode.
For detailed build instructions see readme.txt in the board directory.
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Move some of the code for the "lane_bank" and "cpld" code local
commands so that they are not built for SPL as they can only be
used in full U-Boot. This means we can mark a few functions as
static as well now.
Cc: Alison Wang <alison.wang@freescale.com>
Cc: Sumit Garg <sumit.garg@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Alison Wang <alison.wang@nxp.com>
Tested-by: Alison Wang <alison.wang@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add a CONFIG_SPL_BUILD guard around the code for the "mux" command so
it is not included in SPL.
Cc: Qiang Zhao <qiang.zhao@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Reviewed-by: Qiang Zhao <qiang.zhao@nxp.com>
QMAP value contains information about QSPI chip-selects. These bits
are used to display information of boot device in checkboard()
function.
QMAP value is stored in most significant 3-bits of 8-bit register
brdcfg[0] in Qixis, this patch corrects code to get QMAP bits using
below logic:
(brdcfg[0] >> 5) & 0x7
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Remove Board Arch print as its value is always constant '1' and does
not contain any important information to display during boot.
Add print to display Board FPGA version.
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
As part of chain of trust with confidentiality along with distro
boot, linux kernel image needs to be stored in encrypted form on
ext4 boot partition. So enable CONFIG_CMD_EXT4_WRITE in case of
Secure boot on ARM based platforms.
Signed-off-by: Sumit Garg <sumit.garg@nxp.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <york.sun@nxp.com>
LS1012A-2G5RDB belongs to LS1012A family with features 2 2.5G SGMII
PFE MAC, SATA, USB 2.0/3.0, WiFi DDR, eMMC, QuadSPI, UART.
Signed-off-by: Bhaskar Upadhaya <Bhaskar.Upadhaya@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Like many other i.MX6 based boards, there are multiple variants of
the cm-fx6 module featuring different SoC variants. Furthermore, the
module can be paired with multiple baseboards.
At the same time modern distribution like Fedora require U-Boot to
select a proper devicetree which depends on the SoC variant and the
baseboard.
Thus, export the SoC variant and the actual board to the environment
following the conventions of other i.MX6 devices (e.g. the NXP boards)
such that the environment can select a devicetree file to load.
For now, we only know for sure that the cm-fx6 module and the SB-fx6m
baseboard amount to a Utilite Computer variant (depending on the SoC).
Further combinations may be added in the future; e.g. CompuLab's
evaluation board once someone can verify the identification string
stored in its eeprom.
Signed-off-by: Christopher Spinrath <christopher.spinrath@rwth-aachen.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Currently mmdc_do_dqs_calibration() and mmdc_do_write_level_calibration()
show the same error message, which is confusing for debugging.
Disambiguate the mmdc_do_dqs_calibration() error message.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
mx6sabresd board uses the following pins for console:
PAD_CSI0_DAT10__UART1_TX_DATA
PAD_CSI0_DAT11__UART1_RX_DATA
,so put it in the same config option as wandboard.
mx6sabreauto board uses the following pins for console:
PAD_KEY_COL0__UART4_TX_DATA
PAD_KEY_ROW0__UART4_RX_DATA
So do not mention sabreauto board as part of the UART1_SD3_DAT6_7 option.
The config option for sabreauto can be added later when needed.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
The code for programming the OTP fuses on the PMIC PF0100 can only be
used in full U-Boot, so do not build / link it into SPL.
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Max Krummenacher <max.krummenacher@toradex.com>
The command can only be used from full U-Boot, so do not build it into
SPL.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
The command can only be used from full U-Boot, so do not build it into
SPL.
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Acked-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Because kernel set WDOG_B mux before pad with the common pinctrl
framwork now and wdog reset will be triggered once set WDOG_B mux
with default pad setting, we set pad setting here to workaround this.
Since imx_iomux_v3_setup_pad also set mux before pad setting, we set
as GPIO mux firstly here to workaround it.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Enable I2C/MMC/GPIO/REGUALTOR/PMIC/USB DM drivers.
There are some dependency, such as when DM MMC enabled, USB compile error.
Also the i.MX I2C MMC DM driver does not support legacy GPIO interface.
So enable them all together.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
