Commit graph

12 commits

Author SHA1 Message Date
Simon Glass
762592cb5c Correct SPL uses of FEC_MXC
This converts 4 usages of this option to the non-SPL form, since there is
no SPL_FEC_MXC defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-10 07:41:41 -05:00
Simon Glass
299cca0e72 Correct SPL uses of DWC_ETH_QOS
This converts 3 usages of this option to the non-SPL form, since there is
no SPL_DWC_ETH_QOS defined in Kconfig

Signed-off-by: Simon Glass <sjg@chromium.org>
2023-02-09 16:32:26 -05:00
Peng Fan
a38ed61643 imx: imx8mp_evk: enable pinctrl_wdog in SPL
Mark pinctrl_wdog as u-boot,dm-spl to clean up board code,

The set_wdog_reset() function is not necessary as this is handled by
the imx_watchdog.c driver due to the 'fsl,ext-reset-output' property
being set.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:29 +02:00
Peng Fan
ae188eb61c imx: imx8mp_evk: enable CONFIG_DM_SERIAL
Enable CONFIG_DM_SERIAL. uart2 and its pinmux was already
marked with u-boot,dm-spl.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-21 15:18:25 +02:00
Ye Li
c852a2bf6f imx8mp_evk: Remove EQoS PHY reset codes
Since we uses the DTS and PHY reset gpio in EQoS driver to do the
reset, remove the duplicated codes from board file.

Signed-off-by: Ye Li <ye.li@nxp.com>
2021-10-21 13:59:26 +02:00
Ye Li
e1260aef37 imx8mp_evk: Fix incorrect cascade for FEC and EQOS setup
The setup functions should be independent for two ethernet controllers

Signed-off-by: Ye Li <ye.li@nxp.com>
2021-10-21 13:59:26 +02:00
Simon Glass
401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
Peng Fan
48b90f86c5 imx: imx8mp_evk: enable eth support
Add board code to configure the network interface
Add net defconfig

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2021-01-23 11:30:30 +01:00
Peng Fan
3c41728d80 imx8m: Refactor the OPTEE memory removal
Current codes assume the OPTEE address is at the end of first DRAM bank.
Adjust the process to allow OPTEE in the middle of first bank.

When OPTEE memory is removed from first bank, it may split the first bank
to two banks, adjust the MMU table for the split case,
Since the default CONFIG_NR_DRAM_BANKS is 4, it is enough, just enlarge
i.MX8MP evk to default to avoid issue.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Silvano di Ninno <silvano.dininno@nxp.com>
Tested-by: Silvano di Ninno <silvano.dininno@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-07-14 15:23:48 +08:00
Simon Glass
0914011310 command: Remove the cmd_tbl_t typedef
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.

Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.

This requires quite a few header-file additions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 18:36:55 -04:00
Simon Glass
691d719db7 common: Drop init.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Peng Fan
439321b264 imx: add i.MX8MP EVK board
Add basic i.MX8MP EVK board support

U-Boot SPL 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800)
power_pca9450b_init
DDRINFO: start DRAM init
DDRINFO:ddrphy calibration done
DDRINFO: ddrmix config done
Normal Boot
Failed to find clock node. Check device tree
WDT:   Not found!
Trying to boot from BOOTROM
image offset 0x8000, pagesize 0x200, ivt offset 0x0

U-Boot 2020.01-rc4-00388-gb1bf40c0ae-dirty (Dec 30 2019 - 17:55:33 +0800)

CPU:   Freescale i.MX8MP rev1.0 at 1000 MHz
Reset cause: POR
Model: NXP i.MX8MPlus EVK board
DRAM:  6 GiB
MMC:   FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In:    serial
Out:   serial
Err:   serial
Net:   No ethernet found.
Hit any key to stop autoboot:  0
u-boot=> mmc list
FSL_SDHC: 1 (SD)
FSL_SDHC: 2

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2020-01-08 13:20:09 +01:00