Commit graph

984 commits

Author SHA1 Message Date
Simon Glass
b0265d56fe dm: tegra: nand: Remove use of fdtdec GPIO support
These functions are going away, so use the new uclass support instead.

Signed-off-by: Simon Glass <sjg@chromium.org>
2015-01-29 17:09:52 -07:00
Heiko Schocher
40da2a2a08 ubi: reset mtd_devs when ubi part fail
if "ubi part" fails, reset also mtd_devs to 0, as
further "ubi part" would use wrong mtd_devs.

Signed-off-by: Heiko Schocher <hs@denx.de>
2015-01-28 07:41:18 +01:00
Masahiro Yamada
5344cc1a82 powerpc: ppc4xx: remove PPChameleonEVB, CATcenter boards
These boards are still non-generic boards.

It is a good thing that we can drop board-specific hack code
from drivers/mtd/nand/nand_base.c

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Andrea "llandre" Marson <andrea.marson@dave-tech.it>
2015-01-23 16:53:36 -05:00
Daniel Mack
c316f577b4 mtd: OMAP: Enable GPMC prefetch mode
Enable GPMC's prefetch feature for NAND access. This speeds up NAND read
access a lot by pre-fetching contents in the background and reading them
through the FIFO address.

The current implementation has two limitations:

 a) it only works in 8-bit mode
 b) it only supports read access

Both is easily fixable by someone who has hardware to implement it.

Note that U-Boot code uses non word-aligned buffers to read data into, and
request read lengths that are not multiples of 4, so both partial buffers
(head and tail) have to be addressed.

Tested on AM335x hardware.

Tested-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Guido Martínez <guido@vanguardiasur.com.ar>
Signed-off-by: Daniel Mack <zonque@gmail.com>
[trini: Make apply again, use 'cs' fix pointed out by Guido]
Signed-off-by: Tom Rini <trini@ti.com>
2015-01-13 11:51:23 -05:00
Masahiro Yamada
ab37b76d5d mtd: nand: do not scan BBT after scrub
Currently, "nand scrub" runs chip->scan_bbt at the end of
nand_erase_opts() even if NAND_SKIP_BBTSCAN flag is set.

It violates the intention of NAND_SKIP_BBTSCAN.

Move NAND_SKIP_BBTSCAN flag check to nand_block_checkbad() so that
chip->scan_bbt() is never run if NAND_SKIP_BBTSCAN is set.

Also, unset NAND_BBT_SCANNED flag instead of running chip->scan_bbt()
right after scrub.  We can be lazier here because the BBT is scanned
at the next call of nand_block_checkbad().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
2015-01-09 12:19:06 -06:00
Masahiro Yamada
bf80ee6e1d mtd: nand: Mark the BBT as scanned prior to calling scan_bbt again
Commit 35c204d8a9 (nand: reinstate lazy bad block scanning)
broke NAND_BBT_USE_FLASH feature.

Its git-log claimed that it reinstated the change as by commit
fb49454b1b ("nand: reinstate lazy bad block scanning"), but it moved
"chip->options |= NAND_BBT_SCANNED" below "chip->scan_bbt(mtd);".

It causes recursion if scan_bbt does not find a flash based BBT
and tries to write one, and the attempt to erase the BBT area
causes a bad block check.

Reinstate commit ff49ea8977 (NAND: Mark the BBT as scanned prior to
calling scan_bbt.).

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Rostislav Lisovy <lisovy@merica.cz>
Cc: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
2015-01-09 12:19:02 -06:00
Masahiro Yamada
756963d7da mtd: nand: revive "nand scrub" command
Since commit ff94bc40af (mtd, ubi, ubifs: resync with Linux-3.14),
the "nand scrub" command has not been working.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
2015-01-09 12:18:58 -06:00
Guido Martínez
eb54d2c70c mtd: nand: omap_gpmc: fix error handling
"err" was an unsigned variable, causing negative error codes to turn
into positive values, which are interpreted as an amount of succesfully
corrected bitflips (and thus not an error).

In particular, this resulted in that if the elm reports uncorrectable
errors (-EBADMSG), the MTD layer (and UBI) falsely succeeded.

Signed-off-by: Guido Martínez <guido@vanguardiasur.com.ar>
Reviewed-by: Stefan Roese <sr@denx.de>
2015-01-05 16:40:18 -05:00
Adnan Ali
babe6994ca sf: sf_params: Add S25FL164K flash identifier info
Add the necessary flash entry for the Spansion S25FL164K
flash. Tested on Marvell 88F6218 based design.

Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-12-18 18:48:30 +05:30
Adnan Ali
cf156007e0 sf: sf_params: Add S25FL116K flash support
Added S25FL116K flash and tested on Marvell 88F6281 based system.

Signed-off-by: Adnan Ali <adnan.ali@codethink.co.uk>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-12-18 18:45:35 +05:30
Shengzhou Liu
b45a3de086 mtd/spi: Add support for SST25WF040B
Add support for SST25WF040B-40I-SN flash.
Tested on T1024QDS board.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-12-18 18:19:24 +05:30
Jagannadha Sutradharudu Teki
2bf48026fd mtd: sf: Zap ramtron driver
Removed ramtron driver since the EMK boards are
no longer been active, and these are the only boards
used this flash driver.

Commit details for EMK zap:
"ppc/arm: zap EMK boards"
(sha1: d58a9451e7)

Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Cc: Reinhard Meyer <reinhard.meyer@emk-elektronik.de>
2014-12-18 18:17:54 +05:30
Jagannadha Sutradharudu Teki
54ba653ab6 sf: Enable byte program support
Enabled byte program support for sst flashes in sf.

Few controllers will only support BP, so this patch gives
a tx transfer flag to set the BP so-that sf will operate
on byte program transfer.

A new TX operation mode SPI_OPM_TX_BP is introduced for such SPI
controller to use byte program op for SST flash.

Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2014-12-13 15:08:04 -07:00
Bin Meng
74c2cee4e8 spi: sf: Support byte program for sst spi flash
Currently if SST flash advertises SST_WP flag in the params table
the word program command (ADh) with auto address increment will be
used for the flash write op. However some SPI controllers do not
support the word program command (like the Intel ICH 7), the byte
programm command (02h) has to be used.

Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-12-13 15:08:04 -07:00
Simon Glass
b648742a17 spi: Fix flag collision for SST_WP
At present SECT_4K is the same as SST_WP so we cannot tell these apart. Fix
this so that the table in sf_params.c can be used correctly.

Reported-by: Jens Rottmann <Jens.Rottmann@adlinktech.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-12-13 15:08:04 -07:00
Jagannadha Sutradharudu Teki
6dd6e90e13 sf: Fix look for the fastest read command
Few of the spi controllers are only supports array slow
read which is quite different behaviour compared to others.

So this fix on sf will correctly handle the slow read supported
controllers.

Signed-off-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Tested-by: Bin Meng <bmeng.cn@gmail.com>
2014-12-13 15:08:04 -07:00
Jaiprakash Singh
1d421cc677 driver/mtd: Fix IFC compilation warnings
'eccstat' array elements might be used uninitialized

Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:42:32 -08:00
Alison Wang
8ab967b6c6 arm: ls102xa: Add NAND boot support for LS1021AQDS board
This patch adds NAND boot support for LS1021AQDS board. SPL
framework is used. PBL initialize the internal RAM and copy
SPL to it, then SPL initialize DDR using SPD and copy u-boot
from NAND flash to DDR, finally SPL transfer control to u-boot.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Signed-off-by: Alison Wang <alison.wang@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-11 09:40:24 -08:00
Stefan Roese
fb384c4720 mtd: nand: omap_gpmc: Always use ready/busy pin
The functions to detect the state of the ready / busy signal is already
available but only used in the SPL case. Lets use it always, also for the
main U-Boot. As all boards should have this HW connection.

Testing on Siemens Draco (am335x) showed a small perfomance gain by using
this ready pin to detect the NAND chip state. Here the values tested on
Draco with Hynix 4GBit NAND:

Without NAND ready pin:

U-Boot# time nand read 80400000 0 400000

NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK

time: 2.947 seconds, 2947 ticks

With NAND ready pin:

U-Boot# time nand read 80400000 0 400000

NAND read: device 0 offset 0x0, size 0x400000
4194304 bytes read: OK

time: 2.795 seconds, 2795 ticks

So an increase of approx. 5%.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Roger Meier <r.meier@siemens.com>
Cc: Samuel Egli <samuel.egli@siemens.com>
2014-12-04 21:28:31 -05:00
Marek Vasut
b19157bf3f mtd: nand: s3c: Unify the register definition and naming
Merge struct s3c2410_nand and struct s3c2440_nand into one unified
struct s3c24x0_nand. While at it, fix up and rename the functions
to retrieve the NAND base address and fix up the s3c NAND driver to
reflect this change.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Lukasz Majewski <l.majewski@samsung.com>
Cc: Minkyu Kang <mk7.kang@samsung.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
2014-11-26 23:21:43 -06:00
Sanchayan Maity
2260457341 mtd/nand/vf610_nfc: Disable subpage writes
This patch disables subpage writes for vf610_nfc nand
driver. This is required, as without this fix, writing
unaligned u-boot images with DFU results in a hang.
Trying to write unalgined binary images also results
in a hang, without disabling subpage writes.

Patch has been tested on a Colibri VF61 module.

Signed-off-by: Sanchayan Maity <maitysanchayan@gmail.com>
2014-11-26 19:53:49 -06:00
Masahiro Yamada
f09eb52b3f mtd: denali: set some registers after nand_scan_ident()
Some but not all of implementations of the Denali NAND controller
have hardware circuits to detect the device parameters such as
page_size, erase_size, etc.  Even on those SoCs with such hardware
supported, the hardware is known to detect wrong parameters for some
nasty (almost buggy) NAND devices.  The device parameters detected
during nand_scan_ident() are more trustworthy.

This commit sets some hardware registers to mtd->pagesize,
mtd->oobsize, etc. in the code between nand_scan_ident() and
nand_scan_tail().

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
2014-11-26 19:53:22 -06:00
Masahiro Yamada
65e4145a20 mtd: denali: use CONFIG_SYS_NAND_SELF_INIT
Some variants of the Denali NAND controller need some registers
set up based on the device information that has been detected during
nand_scan_ident().

CONFIG_SYS_NAND_SELF_INIT has to be defined to insert code between
nand_scan_ident() and nand_scan_tail().  It is also helpful to reduce
the difference between this driver and its Linux counterpart because
this driver was ported from Linux.  Moreover, doc/README.nand recommends
to use CONFIG_SYS_NAND_SELF_INIT.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Chin Liang See <clsee@altera.com>
2014-11-26 19:53:19 -06:00
Rostislav Lisovy
35c204d8a9 nand: reinstate lazy bad block scanning
Commit ff94bc40af
("mtd, ubi, ubifs: resync with Linux-3.14")
accidentally reverted part of the commit
13f0fd94e3
("NAND: Scan bad blocks lazily.").

Reinstate the change as by commit
fb49454b1b
("nand: reinstate lazy bad block scanning")

Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
Acked-by: Heiko Schocher <hs@denx.de>
2014-11-26 19:51:51 -06:00
Tom Rini
1739564e75 Merge git://git.denx.de/u-boot-dm
Conflicts:
	drivers/serial/serial-uclass.c

Signed-off-by: Tom Rini <trini@ti.com>
2014-11-24 12:01:48 -05:00
Masahiro Yamada
b41411954d linux/kernel.h: sync min, max, min3, max3 macros with Linux
U-Boot has never cared about the type when we get max/min of two
values, but Linux Kernel does.  This commit gets min, max, min3, max3
macros synced with the kernel introducing type checks.

Many of references of those macros must be fixed to suppress warnings.
We have two options:
 - Use min, max, min3, max3 only when the arguments have the same type
   (or add casts to the arguments)
 - Use min_t/max_t instead with the appropriate type for the first
   argument

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Pavel Machek <pavel@denx.de>
Acked-by: Lukasz Majewski <l.majewski@samsung.com>
Tested-by: Lukasz Majewski <l.majewski@samsung.com>
[trini: Fixup arch/blackfin/lib/string.c]
Signed-off-by: Tom Rini <trini@ti.com>
2014-11-23 06:48:30 -05:00
Simon Glass
6b18656aff dm: spi: Use device_bind_driver() instead of our own function
The SPI function does the same thing, so we may as well just use the new
generic function. The 'cs' parameter was not actually used, so can be
dropped.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-11-22 10:16:48 +01:00
Simon Glass
ff56bba2d6 dm: spi: Correct handling of SPI chip selects in sandbox
This code was not updated when the chip select handling was adjusted. Fix
it to call the correct function.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-11-22 10:16:47 +01:00
Tom Rini
4d70b34d7f Merge branch 'master' of git://git.denx.de/u-boot-ubi 2014-11-19 23:18:29 -05:00
Dirk Eibach
f3c89d9228 mtd: Handle 29LV800BT
The device id makes u-boot think that this chip needs
cfi_reverse_geometry(), which is not the case.
Add it to jedec_flash, so it is handled properly.

Signed-off-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
2014-11-19 08:48:41 +01:00
Heiko Schocher
65e5cb54d0 mtd, cfi, ubi: add missing writebufsize initialization
ff94bc40af "mtd, ubi, ubifs: resync with Linux-3.14"
introduced the writebufsize field in struct mtd_info, which
is not initialized in the cfi_flash driver, which leads in
not working ubi on cfi flashes. Fix it

Signed-off-by: Heiko Schocher <hs@denx.de>
Reported-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Andrew Ruder <andrew.ruder@elecsyscorp.com>
2014-11-19 07:54:04 +01:00
Josh Wu
7df4486d04 mtd: atmel_nand: runtime to build gf table for pmecc
As in SAMA5D4 SoC, the gf table in ROM code can not be seen.
So, when we try to use PMECC, we need to build it when do
initialization.
Add a macro NO_GALOIS_TABLE_IN_ROM in soc header file. If it
is defined we will build gf table runtime.

The PMECC use the BCH algorithm, so based on the build_gf_tables()
function in lib/bch.c, we can build the Galois Field lookup table.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:18 -05:00
Heiko Schocher
667af36905 spl, mtd, nand, atmel_nand: invert device ready pin logic
device ready pin is signalling that the device is ready on state 1
not on 0. Simmiliar as it is in drivers/mtd/nand/nand_spl_simple.c

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:17 -05:00
Heiko Schocher
4dfd360589 spl, nand, atmel_nand: add erase one block function
erase one nand block in spl code. keep it simple, as size matters
This is used on the upcoming taurus spl support.

Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:17 -05:00
Heiko Schocher
c1ec406282 mtd: atmel_nand: add missing include
using this driver in SPL code with CONFIG_SPL_NAND_ECC
configured leads in an compileerror. Fix this.

Signed-off-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Reviewed-by: Bo Shen <voice.shen@atmel.com>
[fix subject]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-11-17 08:47:17 -05:00
Tom Rini
625509ab0e Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-11-05 12:48:09 -05:00
Marek Vasut
f9cfe17b3d mtd: nand: mxs: Add ECC geometry for 2048b/112b NAND
Add ECC geometry for NAND which has 2048b pagesize and 112b OOB
size. This is for example Macronix MX30LF2G28AB chip.

Signed-off-by: Marek Vasut <marex@denx.de>
2014-10-30 11:02:23 +01:00
Jeroen Hofstee
441529795c omap_gpmc: fix warnigs with W=1
- make omap_spl_dev_ready static
- make omap_reverse_list static, move to under CONFIG_NAND_OMAP_ELM

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
Signed-off-by: Tom Rini <trini@ti.com>
2014-10-25 07:02:02 -04:00
Jeroen Hofstee
00dcb07c54 cti_flash.c: use __weak when requested for flash_(read|write){8,16,32,64}
For various reasons (design, errata) boards may need to implement their
own versions of these accessors.  So in the case of
CONFIG_CFI_FLASH_USE_WEAK_ACCESSOR mark the functions as weak.  In the
normal case mark them as static to allow for better optimization.

Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
[trini: Reword commit message]
Signed-off-by: Tom Rini <trini@ti.com>
2014-10-25 06:58:51 -04:00
Stefan Roese
3dc23f7852 arm: marvell: Move arch/kirkwood.h to arch/soc.h
This move makes is possible to use this header not only from kirkwood
platforms but from all Marvell mvebu platforms.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Acked-by: Prafulla Wadaskar <prafulla@marvell.com>
2014-10-23 09:59:20 -04:00
Simon Glass
b6c2956def dm: sf: sandbox: Convert SPI flash driver to driver model
Convert sandbox's spi flash emulation driver to use driver model.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22 10:36:51 -06:00
Simon Glass
fbb099183e dm: Convert spi_flash_probe() and 'sf probe' to use driver model
We want the SPI flash probing feature to operate as a standard driver.
Add a driver for the basic probing feature used by most boards. This
will be activated by device_probe() as with any other driver.

The 'sf probe' command currently keeps track of the SPI slave that it
last used. This doesn't work with driver model, since some other driver
or system may have probed the device and have access to it too. On the
other hand, if we try to probe a device twice the second probe is a nop
with driver model.

Fix this by searching for the matching device, removing it, and then
probing it again. This should work as expected regardless of other device
activity.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22 10:36:50 -06:00
Simon Glass
4c2dbefde5 dm: sf: Add a uclass for SPI flash
Add a driver model uclass for SPI flash which supports the common
operations (read, write, erase). Since we must keep support for the
non-dm interface, some modification of the spi_flash header is required.

CONFIG_DM_SPI_FLASH is used to enable driver model for SPI flash.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22 10:36:50 -06:00
Simon Glass
ae242cbfd0 spi: Use error return value in sf_ops
Adjust spi_flash_probe_slave() to return an error value instead of a
pointer so we get the correct error return.

Have the caller allocate memory for spi_flash to simplify error handling,
and also so that driver model can use its existing allocated memory.

Add a spi.h include in the sf_params file.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22 10:36:50 -06:00
Simon Glass
ff0960f9a0 sf: Tidy up public and private header files
Since spi_flash.h is supposed to be the public API for SPI flash, move
private things to sf_internal.h. Also tidy up a few comment nits.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22 10:36:50 -06:00
Simon Glass
843c9e8796 dm: Add spi.h header to a few files
Some files are using SPI functions but not explitly including the SPI
header file. Fix this, since driver model needs it.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-10-22 10:36:47 -06:00
Albert ARIBAUD
790af81543 Merge branch 'u-boot/master' into 'u-boot-arm/master' 2014-10-11 01:20:30 +02:00
Masahiro Yamada
ed3c980bee mtd: denali: support NAND_CMD_RNDOUT command
The function nand_flash_detect_ext_param_page() requires
NAND_CMD_RNDOUT command supported.  It is necessary to detect some
types of ONFi-compliant devices.  Without it, the error message
"unsupported command received 0x5" is shown.

Let's support this command on the Denali NAND controller driver.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-09 17:33:26 -05:00
Masahiro Yamada
05968e7cfd mtd: denali: fix NAND_CMD_PARAM command
NAND_CMD_PARAM (0xEC) command is not working on the Denali
NAND controller driver.

Unlike NAND_CMD_READID (0x90), when the NAND_CMD_PARAM command
is followed by an address cycle, the target device goes busy.
(R/B# is deasserted)
Wait until the parameter data are ready.

In addition, unnecessary clear_interrupts() should be removed.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Chin Liang See <clsee@altera.com>
2014-10-09 17:33:24 -05:00
Albert ARIBAUD
4b19b7448e Merge remote-tracking branch 'u-boot-imx/master'
The single file conflict below is actually trivial.

Conflicts:
	board/boundary/nitrogen6x/nitrogen6x.c
2014-10-08 21:20:49 +02:00
Tom Rini
dd0204e48d Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-10-07 07:38:39 -04:00
Baruch Siach
9169305599 cfi_flash: don't hide write/erase errors
Partially revert commit 0d01f66d23 (CFI: cfi_flash write fix for AMD
legacy).

flash_full_status_check() used to skip status register parsing when
flash_status_check() returns OK. This is wrong since flash_status_check()
must return OK for other status bits to be valid.

Cc: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
2014-10-06 14:12:12 +02:00
Masahiro Yamada
845034e6b2 mtd: denali: add Denali NAND driver for SPL
The SPL-mode driver for Denali(Cadence) NAND Flash Memory Controller IP.

This driver requires two CONFIG macros:
 - CONFIG_SPL_NAND_DENALI
     Define to enable this driver.
 - CONFIG_SYS_NAND_BAD_BLOCK_POS
     Specify bad block mark position in the oob space. Typically 0.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
2014-10-05 14:10:09 +09:00
Masahiro Yamada
4b0abf9f3c mtd: denali: add Denali controller configs to Kconfig
Commit 3eb3e72a3f (nand/denali: Adding Denali NAND driver support)
introduced some new options, and some of them were documented by
commit f9860cf081 (nand/denali: Document CONFIG symbols).

This commit allows users to enable/disable them via Kconfig
with more detailed help docs.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Cc: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
2014-10-05 14:10:09 +09:00
Tom Rini
be9f643ae6 Merge branch 'for-tom' of git://git.denx.de/u-boot-dm 2014-09-26 20:10:48 -04:00
Simon Glass
110bdee00f sandbox: Convert SPI flash emulation to use sf_params
At present sandbox has its own table of supported SPI flash chips. Now that
the SPI flash system is fully consolidated and has its own list, sandbox
should use that.

This enables us to expand the number of chips that sandbox supports.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-26 15:00:36 -06:00
Tom Rini
2c2277f15c Merge branch 'master' of git://git.denx.de/u-boot-fsl-qoriq 2014-09-26 09:57:52 -04:00
Chin Liang See
3eb3e72a3f nand/denali: Adding Denali NAND driver support
To add the Denali NAND driver support into U-Boot.
This driver is leveraged from Linux with commit ID
fdbad98dff8007f2b8bee6698b5d25ebba0471c9. For Denali
controller 64 variance, you need to declare macro
CONFIG_SYS_NAND_DENALI_64BIT.

Signed-off-by: Chin Liang See <clsee@altera.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Tested-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
2014-09-25 13:43:16 -05:00
Stefan Roese
be16aba5ce mtd: nand: Fix length bug in ioread16_rep() and iowrite16_rep()
The ioread16_rep() and iowrite16_rep() implementations are U-Boot specific
and have been introduced with the Linux MTD v3.14 sync. While introducing
these functions, the length for the loop has been miscalculated. The ">> 1"
is already present in the caller. So lets remove it in the function.

Tested on omap3_ha.

Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Heiko Schocher <hs@denx.de>
Cc: Tom Rini <trini@ti.com>
Cc: Scott Wood <scottwood@freescale.com>
Acked-by: Heiko Schocher <hs@denx.de>
2014-09-25 13:43:00 -05:00
Rostislav Lisovy
2f665945b3 mtd: nand: am335x: Fix 'bit-flip' errors in SPL
OMAP GPMC driver used with some NAND Flash devices
(e.g. Spansion S34ML08G1) causes that U-boot shows
hundreds of 'nand: bit-flip corrected' error messages.
Possible cause was discussed in the mailinglist thread:
http://lists.denx.de/pipermail/u-boot/2014-April/177508.html

The issue was partially fixed with the cc81a5291910d7a.git
however this has to be done to fix the SPL.

The original author of the code is Belisko Marek
<marek.belisko@gmail.com>

Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-25 13:43:00 -05:00
Prabhakar Kushwaha
5b8388a827 driver/mtd: Use generic timer API for FSL IFC, eLBC
Freescale's flash control driver is using architecture specific timer API
i.e. usec2ticks

Replace usec2ticks with get_timer() (generic timer API)

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Acked-by: Scott Wood <scottwood@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-09-25 08:36:17 -07:00
Masahiro Yamada
ed36323f6d kconfig: add blank Kconfig files
This would be useful to start moving various config options.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2014-09-24 18:30:28 -04:00
Stefan Roese
31969b8993 sf: Add M25PX64 SPI NOR flash ID
Add ID for this Numonix / STMicro chip.

Tested on Marvell DB-78460-BP board.

Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Luka Perkov <luka@openwrt.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-24 17:46:25 +05:30
Nikita Kiryanov
88e34e5ff7 spl: replace CONFIG_SPL_SPI_* with CONFIG_SF_DEFAULT_*
Currently, CONFIG_SPL_SPI_* #defines are used for controlling SPI boot in
SPL. These #defines do not allow the user to select SPI mode for the SPI flash
(there's no CONFIG_SPL_SPI_MODE, so the SPI mode is hardcoded in
spi_spl_load.c), and duplicate information already provided by
CONFIG_SF_DEFAULT_* #defines.

Kill CONFIG_SPL_SPI_*, and use CONFIG_SF_DEFAULT_* instead.

Cc: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Cc: Vitaly Andrianov <vitalya@ti.com>
Cc: Lars Poeschel <poeschel@lemonage.de>
Cc: Bo Shen <voice.shen@atmel.com>
Cc: Hannes Petermaier <hannes.petermaier@br-automation.com>
Cc: Michal Simek <monstr@monstr.eu>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-24 17:40:10 +05:30
Nikita Kiryanov
01d2aaf61b mtd: spi: add support for M25PE16 and M25PX16
Add support for M25PE16 and M25PX16

Cc: Marek Vasut <marex@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
Signed-off-by: Nikita Kiryanov <nikita@compulab.co.il>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-09-24 17:25:16 +05:30
Simon Glass
bf1a86fca0 sf: Add an empty entry to the parameter list
The list is supposed to be terminated with a NULL name, but is not. If a
board probes a chip which does not appear in the table, U-Boot will crash
(at least on sandbox).

Signed-off-by: Simon Glass <sjg@chromium.org>
2014-09-23 12:44:30 -06:00
Stefano Babic
42817eb85d Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-09-22 15:51:01 +02:00
Boris BREZILLON
d357b94041 mtd: atmel_nand: Disable subpage NAND write when using Atmel PMECC
Disable subpage write when using PMECC to prevent buggy partial page write.

This fix has been taken from linux sources (see commit
90445ff6241e2a13445310803e2efa606c61f276)

Signed-off-by: Boris BREZILLON <boris.brezillon@free-electrons.com>
Acked-by: Josh Wu <josh.wu@atmel.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:22 +02:00
Wu, Josh
14b3b44eda mtd: atmel-nand: use pmecc_readl(b)/pmecc_writel to access the pmecc register
We defined the macro pmecc_readl(b)/pmecc_writel for pmecc register access.
But in the driver we also use the readl(b)/writel.
To keep consistent, this patch make all use pmecc_readl(b)/pmecc_writel.

Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
2014-09-19 00:11:13 +02:00
maxin.john@enea.com
5da163d665 mtdcore: Fix a build error with CONFIG_CMD_MTDPARTS_SPREAD
This patch fixes the build error for CONFIG_CMD_MTDPARTS_SPREAD

Signed-off-by: Maxin B. John <maxin.john@enea.com>
2014-09-16 12:23:59 -04:00
Khoronzhuk, Ivan
7206111e52 mtd: nand: davinci_nand: update write_page function for keystone RBL
After mtd was synced with Linux 3.14
(ff94bc40af)
the number of parameters for write_page function of nand_chip was
changed. The additional two var were needed for subpage write.
As keystone has no supbage write they are not needed. So correct
only function definition by upgrading it's parameter list.
That helps to get ritd of compilation warning.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-16 12:23:59 -04:00
Masahiro Yamada
3b61297024 kbuild: force to define __UBOOT__ in all the C sources
U-Boot has imported various source files from other projects,
mostly Linux.

Something like

  #ifdef __UBOOT__
    [ modification for U-Boot ]
  #else
    [ original code ]
  #endif

is an often used strategy for clarification of adjusted parts,
that is, easier re-sync in future.

Instead of defining __UBOOT__ in each source file,
passing it from the top Makefile would be easier.

Signed-off-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Acked-by: Marek Vasut <marex@denx.de>
Acked-by: Heiko Schocher <hs@denx.de>
2014-09-16 12:23:56 -04:00
Stefan Agner
72d7beabf7 mtd: nand: add Freescale vf610_nfc driver
This adds initial support for Freescale NFC (NAND Flash Controller)
found in ARM Vybrid SoC's, Power Architecture MPC5125 and others.
The driver is called vf610_nfc since this is the first supported
and tested hardware platform supported by the driver.

Signed-off-by: Stefan Agner <stefan@agner.ch>
Acked-by: Bill Pringlemeir <bpringlemeir@nbsps.com>
2014-09-16 13:25:18 +02:00
Rostislav Lisovy
cc81a52919 mtd: nand: omap_gpmc: Fix 'bit-flip' errors
OMAP GPMC driver used with some NAND Flash devices (e.g. Spansion
S34ML08G1) causes that U-boot shows hundreds of 'nand: bit-flip
corrected' error messages. Possible cause was discussed in the
mailinglist thread:
http://lists.denx.de/pipermail/u-boot/2014-April/177508.html

Quote (Author: Pekon Gupta <pekon@ti.com>): "The issue is mainly
due to a NAND protocol violation in the omap driver since the
Random Data Output command (05h-E0h) expects to see only the
column address that should be addressed within the already loaded
read page into the read buffer. Only 2 address cycles with ALE
active should be provided between the 05h and E0h commands. The
Page read command expects the full address footprint (2bytes for
column address + 3bytes for row address), but once the page is
loaded into the read buffer, Random Data Output should be used
with only 2bytes for column address."

This patch combines the solution proposed in the mailinglist and
the patch provided by the Spansion company (GPLv2 code, source:
http://www.spansion.com/Support/Software/u-boot-psp-04.04.00.01-NAND.zip)

Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-04 13:06:00 -04:00
Rostislav Lisovy
5c3f7e0ead mtd: nand: omap_gpmc: Enable multiple NAND flash devices
Since the CS of a device connected to the GPMC was
stored in the global variable, it was not possible to
use multiple devices. In this patch the CS is stored per
device in its 'struct omap_nand_info'. This makes it
possible to use up to 'GPMC_MAX_CS' NAND Flash devices
connected to U-boot.

Signed-off-by: Rostislav Lisovy <lisovy@merica.cz>
2014-09-04 13:06:00 -04:00
Khoronzhuk, Ivan
fc12a1f589 mtd: nand: davinci_nand: correct keystone RBL layout definition
In case when 4K page keystone RBL layout is used the compilation
error is appeared. That's because the #ifdef has to be placed under
struct name. This patch correct it.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-09-04 13:06:00 -04:00
Holger Brunck
292221e183 arm/kirkwood/nand: allow forced disabling for subpage writes
Make it configurable to disable subpage writes like the DaVinci NAND
driver already does.

Signed-off-by: Holger Brunck <holger.brunck@keymile.com>
cc: Valentin Longchamp <valentin.longchamp@keymile.com>
cc: Prafulla Wadaskar <prafulla@marvell.com>
cc: Scott Wood <scottwood@freescale.com>
2014-08-30 07:46:41 -04:00
Tom Rini
5a1095a830 Merge branch 'master' of git://www.denx.de/git/u-boot-imx 2014-08-29 11:06:51 -04:00
Heiko Schocher
4e67c57125 mtd,ubi,ubifs: sync with linux v3.15
snyc with linux v3.15:

commit 1860e379875dfe7271c649058aeddffe5afd9d0d
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Sun Jun 8 11:19:54 2014 -0700

    Linux 3.15

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@ti.com>
2014-08-25 19:25:56 -04:00
Heiko Schocher
ddf7bcfa6c mtd, ubi, ubifs: update for the sync with linux v3.14
while playing with the new mtd/ubi/ubifs sync, found some
small updates for it:

- add del_mtd_partition() to include/linux/mtd/mtd
- mtd: add a debug_printf
- remove some not used functions

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Tom Rini <trini@ti.com>
2014-08-25 19:25:56 -04:00
Heiko Schocher
ff94bc40af mtd, ubi, ubifs: resync with Linux-3.14
resync ubi subsystem with linux:

commit 455c6fdbd219161bd09b1165f11699d6d73de11c
Author: Linus Torvalds <torvalds@linux-foundation.org>
Date:   Sun Mar 30 20:40:15 2014 -0700

    Linux 3.14

A nice side effect of this, is we introduce UBI Fastmap support
to U-Boot.

Signed-off-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Tom Rini <trini@ti.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Sergey Lapin <slapin@ossfans.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Joerg Krause <jkrause@posteo.de>
2014-08-25 19:25:55 -04:00
Stefano Babic
e82abaeb7f Merge branch 'master' of git://git.denx.de/u-boot-arm
Conflicts:
	boards.cfg

Signed-off-by: Stefano Babic <sbabic@denx.de>
2014-08-11 10:21:03 +02:00
Stefano Babic
c23154aab5 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-08-08 10:18:40 +02:00
Marek Vasut
a52a178f0b sf: sf_ops: Stop leaking memory
It's usually a common pattern to free() the memory that we allocated.
Implement this here to stop leaking memory.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-08-06 00:18:01 +05:30
Tom Rini
362f16b1e9 Merge branch 'master' of git://git.denx.de/u-boot-arm 2014-07-29 09:41:35 -04:00
Albert ARIBAUD
b1cdd8baa1 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-28 12:26:21 +02:00
Khoronzhuk, Ivan
67ac6ffaee mtd: nand: davinci: add opportunity to write keystone U-boot image
The Keystone SoCs use the same NAND driver as Davinci.
This patch adds opportunity to write Keystone U-boot image to NAND
device using appropriate RBL ECC layout. This is needed only if RBL
boots U-boot from NAND device and that's supposed that raw u-boot
partition is used only for writing image.

The main problem is that default Davinci ECC layout is different from
Keystone RBL layout. To read U-boot image the RBL needs that image was
written using RBL ECC layout.

The BBT table is written using default Davinci layout and has to
be updated using one. The BBT can be updated only while erasing
chip or by forced bad block assigning, so erase function has to
use native ecc layout in order to be able to write BBT correctly.
So if we're writing to NAND U-boot address we use RBL layout for
others we use default ECC layout.

Also remove definition for CONFIG_CMD_NAND_ECCLAYOUT as there is no
reasons to use ECC layout commands. It was added by mistake.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
2014-07-25 15:21:06 -04:00
Heiko Schocher
562f8df18d spi: add config option to enable the WP pin function on st micron flashes
enable the W#/Vpp signal to disable writing to the status
register on ST MICRON flashes like the N25Q128 thorugh
the new config option CONFIG_SYS_SPI_ST_ENABLE_WP_PIN

Signed-off-by: Heiko Schocher <hs@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2014-07-23 12:26:45 +02:00
Prabhakar Kushwaha
591dd19230 driver/nand: Add support of 16K SRAM for IFC 2.0
Internal SRAM has been incresed from 8KB to 16KB for IFC cotroller ver 2.0.

Update the page offset calculation logic to support the same.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Prabhakar Kushwaha
04818bbdc3 driver/nand: Update SRAM initialize logic for IFC.
IFC controller v1.1.0 requires internal SRAM initialize by reading
NAND flash. Higher controller versions have provided "SRAM init" bit in
NCFGR register space.

update SRAM initialize logic to reflect the same.

Also print error message in case of Page read error.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Prabhakar Kushwaha
3bab3d8324 driver/nand:Define MAX_BANKS same as SoC defined for IFC
The number of chip select used by IFC controller vary from one SoC to other.
For eg. P1010 has 4, T4240 has 8.

Update MAX_BANKS same as SoC defined

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-07-22 16:25:54 -07:00
Jeroen Hofstee
c15df21fe7 mtd: cfi_flash: fix clang warning
clang warns this check is silly; it is since s is
a local variable.

u-boot/drivers/mtd/cfi_flash.c:2363:13: warning: comparison of
  array 's' not equal to a null pointer is always true
  else if ((s != NULL) && (strcmp(s, "yes") == 0)) {

cc: Stefan Roese <sr@denx.de>
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-07-18 17:53:22 -04:00
Albert ARIBAUD
e99f30e105 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-01 15:11:18 +02:00
Albert ARIBAUD
d6694aff56 Merge branch 'u-boot-imx/master' into 'u-boot-arm/master' 2014-06-30 23:00:34 +02:00
Khoronzhuk, Ivan
3e01ed00da mtd: nand: davinci: add header file for driver definitions
The definitions inside emif_defs.h concern davinci nand driver and
should be in it's header. So create header file for davinci nand
driver and move definitions from emif_defs.h and nand_defs.h to it.

Acked-by: Vitaly Andrianov <vitalya@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@ti.com>
[trini: Fixup more davinci breakage]
Signed-off-by: Tom Rini <trini@ti.com>
2014-06-19 17:53:58 -04:00
Tom Rini
28b62f0de3 Merge branch 'master' of git://git.denx.de/u-boot-spi 2014-06-11 11:40:11 -04:00
Poddar, Sourav
1f436a6ddf sf: probe: Fix quad bit set path
Currently, flash quad bit is set in "spi_flash_validate_params" and later
at the end in the same api, we write 0 to status register for few flashes,
thereby overriding the quad bit set. This fix moves the quad bit setting
outside this api in "spi_flash_probe_slave"

Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-06-08 23:12:27 +05:30
Siva Durga Prasad Paladugu
0472808608 sf: params: Added support for Spansion S25FL512S_512K
Added support for Spansion chip "S25FL512S_512K".

Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jaganna@xilinx.com>
2014-06-08 23:12:27 +05:30
pekon gupta
46840f66ca mtd: nand: omap: add support for BCH16_ECC - NAND driver updates
This patch add support for BCH16_ECC to omap_gpmc driver.

*need to BCH16 ECC scheme*
With newer SLC Flash technologies and MLC NAND, and large densities, pagesizes
Flash devices have become more suspectible to bit-flips. Thus stronger
ECC schemes are required for protecting the data.
But stronger ECC schemes have come with larger-sized ECC syndromes which require
more space in OOB/Spare. This puts constrains like;
(a) BCH16_ECC can correct 16 bit-flips per 512Bytes of data.
(b) BCH16_ECC generates 26-bytes of ECC syndrome / 512B.
Due to (b) this scheme can only be used with NAND devices which have enough
OOB to satisfy following equation:
OOBsize per page >= 26 * (page-size / 512)

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:10 -04:00
pekon gupta
b80a660338 mtd: nand: omap: add CONFIG_SYS_NAND_BUSWIDTH_16BIT to indicate NAND device bus-width
GPMC controller needs to be configured based on bus-width of the NAND device
connected to it. Also, dynamic detection of NAND bus-width from on-chip ONFI
parameters is not possible in following situations:
SPL:    SPL NAND drivers does not support ONFI parameter reading.
U-boot: GPMC controller iniitalization is done in omap_gpmc.c:board_nand_init()
        which is called before probing for devices, hence any ONFI parameter
        information is not available during GPMC initialization.

Thus, OMAP NAND driver expected board developers to explicitely write GPMC
configurations specific to NAND device attached on board in board files itself.
But this was troublesome for board manufacturers as they need to dive into
lengthy platform & SoC documents to find details of GPMC registers and
appropriate configurations to get NAND device working.

This patch instead adds existing CONFIG_SYS_NAND_BUSWIDTH_16BIT to board config
hich indicates that connected NAND device has x16 bus-width. And then based on
this config GPMC driver itself initializes itself based on NAND bus-width. This
keeps board developers free from knowing GPMC controller specific internals.

Signed-off-by: Pekon Gupta <pekon@ti.com>
2014-06-06 17:46:06 -04:00