By removing this default build target, the "u-boot.kwb" target is not
automatically generated. This fixes a temporary build error when using
out-of-tree builds, as buildman does per default (reported by Simon).
When the full SPL support is added for these targets with the DDR training
code, the "u-boot-spl.kwb" image will be generated automatically.
Users providing a special bin_hdr binary (binary.0) file can always add
this binary file and generate the full firmware image by issuing the
"make u-boot.kwb" command directly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the Marvell DB-88F6820-GP Armada A38x
evaluation board.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Please note that this board support right now only supports the
main U-Boot. Without the bin_hdr integration (DDR training etc). This
will be added in a few days / weeks to complete this board port. But
till then this U-Boot version can be run on the target via the
original Marvell U-Boot via this command:
tftpboot 4000000 db-88f6820-gp/u-boot.bin;go 4000000
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This solves some RX problems that have been seen, when using the
mvneta ethernet driver. The cache needs to be reset into a "clean"
state before using it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
We are not using the coherency feature in U-Boot at all. So lets remove
this configuration from the mbus driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times to a
configurable value. Lets make this init call more flexible by moving
the actually used devices to the config header.
Additionally this patch takes care of the slightly different base
addresses for the ethernet controllers on A38x.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for the Marvell Armada 38x SoC family.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Tested on Marvell DB-88F6820-GP evaluation board.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This way, new MVEBU boards don't need to specifiy the common location
for the SPL linker script.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This define is used by the DDR training code for Armada XP. With the
upcoming addition of Armada 38x support, lets only define it for
Armada XP in this common header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
MAX_MVNETA_DEVS is not used anywhere in U-Boot. So lets remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Since these files will be used for other MVEBU SoC's, lets reflect this
in the headers marcos as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Move arch/arm/include/asm/arch-armada-xp/*
-> arch/arm/mach-mvebu/include/mach/*
Additionally the SYS_SOC is renamed from "armada-xp" to "mvebu". With this
change all these files can better be shared with other, newer Mavell
MVEBU SoC's. Like the upcoming Armada 38x support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Move arch/arm/cpu/armv7armada-xp/* -> arch/arm/mach-mvebu/*
Since this platform will be extended to support other Marvell SoC's as
well, lets rename it directly to mvebu.
This will be used by the upcoming Armada 38x suport (A38x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
New QorIQ p1020 based board support from Arcturus Networks Inc.
http://www.arcturusnetworks.com/products/ucp1020/
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
[York Sun: remove patman tags from commit message]
Reviewed-by: York Sun <yorksun@freescale.com>
To replicate:
1. add to include/configs/p1_p2_rdb_pc.h "#define CONFIG_CMD_GPIO"
2. run `make P1020RDB-PC_defconfig`
3. run CROSS_COMPILE=powerpc-linux- make
and you will get:
common/built-in.o: In function `do_gpio':
u-boot/common/cmd_gpio.c:186: undefined reference to `gpio_request'
u-boot/common/cmd_gpio.c:194: undefined reference to `gpio_direction_input'
u-boot/common/cmd_gpio.c:195: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:200: undefined reference to `gpio_get_value'
u-boot/common/cmd_gpio.c:203: undefined reference to `gpio_direction_output'
u-boot/common/cmd_gpio.c:209: undefined reference to `gpio_free
Signed-off-by: Michael Durrant <mdurrant@arcturusnetworks.com>
Signed-off-by: Oleksandr G Zhadan <oleks@arcturusnetworks.com>
Reviewed-by: York Sun <yorksun@freescale.com>
The SD clock could be generated by platform clock or peripheral
clock for some platforms. This patch adds peripheral clock
support for T1024/T1040/T2080. To enable it, define
CONFIG_FSL_ESDHC_USE_PERIPHERAL_CLK.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Add adapter card type identification support by reading
FPGA STAT_PRES1 register SDHC Card ID[0:2] bits. To use this function,
define CONFIG_FSL_ESDHC_ADAPTER_IDENT.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Cc: York Sun <yorksun@freescale.com>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
[York Sun: resolve conflicts in README.fsl-esdhc]
Reviewed-by: York Sun <yorksun@freescale.com>
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Madalin-Cristian Bucur <madalin.bucur@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch defines the 2 flush_dcache_range and invalidate_dcache_range
functions for all the powerpc architecture. Their implementation is
borrowed from the kernel's misc_32.S file and replace the ones from
mpc86xx and ppc4xx since they were equivalent.
This is a fix for the problem introduced by this patch:
http://patchwork.ozlabs.org/patch/448849/
Signed-off-by: Valentin Longchamp <valentin.longchamp@keymile.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Freescale PCIe controllers v3.0 and later need to set bit
CFG_READY to allow all inbound configuration transactions
to be processed normally when in EP mode. However, bit
CFG_READY has been moved from PCIe configuration space to
CCSR PCIe configuration register comparing previous version.
The patch is to set this bit according to PCIe version.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
This patch adds SD boot support for T4240RDB board. SPL
framework is used. PBL initializes the internal RAM and
copies SPL to it. Then SPL initializes DDR using SPD and
copies u-boot from SD card to DDR, finally SPL transfers
control to u-boot.
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
[York Sun: Fix T4240RDB_SDCARD_defcofig]
Reviewed-by: York Sun <yorksun@freescale.com>
Add a delay of 1 microsecond before issuing soft reset to the
controller to let ongoing ULPI transaction complete.
This prevents corruption of ULPI Function Control Register which
eventually prevents phy clock from entering to low power mode
Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Commit 96d2bb952b ("powerpc/mpc85xx: Don't relocate exception vectors")
simplified IVOR initialization a bit too much, failing to use the
post-relocation offset. This doesn't cause a problem with normal NOR
boot, in which both the pre-relocation and post-relocation addresses
are 64 KiB aligned. However, if TEXT_BASE is only 4 KiB aligned, such
as for NAND/SD/etc. boot on some targets, as well as the QEMU target,
the post-relocation address will not be the same in the lower 16 bits,
as reserve_uboot() ensures that the relocation address is always 64
KiB aligned even if the pre-relocation address was not.
Use the GOT to get the proper post-relocation offsets.
Fixes: 96d2bb952b ("powerpc/mpc85xx: Don't relocate exception vectors")
Signed-off-by: Scott Wood <scottwood@freescale.com>
Cc: Alexander Graf <agraf@suse.de>
Cc: Shaohui Xie <Shaohui.Xie@freescale.com>
Tested-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
Once we add support for the ohci controller the phy-init and phy-power-on
functions may be called twice (once by the ehci code and once by the ohci
code) protect them against this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The 2/3 usb-phys on the sunxi SoCs are really a single separate functional
block, and are modelled as such in devicetree. So once we've moved all the
sunxi usb code to the driver-model then phy_probe will be called once
for the entire block from the driver-model enumeration code.
Move to this now as this also avoids problems with phy_probe being called
multiple times once we introduce ohci support. This also allows us to get rid
of the sunxi_usb_phy_enabled_count variable as phy_probe now is guaranteed
to be called only once.
Since we're effectively rewriting the probe / remove functions, move them
to the end of the file while we are at it, as that is the most logical place
for them.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The usbc.? files now only contain usb-phy related code, rename them to make
this clear.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Rename the sunxi_usbc_foo functions to sunxi_usb_phy_bar to make it clear
that these are usb-phy functions. Also change the verbs & nouns in the suffix
to match the verbs & nouns used in the Linux kernels generic phy framework.
This patch purely renames things, it contains no functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
This is the only function left in sunxi/usbc.c which is not phy related,
so remove it.
This is a preparation patch for turning the usbc.c code into a proper
usb phy driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The sunxi "usbc" code is mostly about phy setup, but currently also sets up
the host controller clocks, which is something which really belongs in the
host controller drivers, so move it there.
This is a preparation patch for moving the sunxi ehci code to the driver
model and for adding ohci support.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that all sunxi boards are using driver-model for gpio (*), we can remove
the non driver-model support from the axp gpio code, and the glue to call
into the axp gpio code from the sunxi_gpio non driver-model code.
*) For the regular u-boot build, SPL still uses non driver-model gpio for
now, but the SPL never uses axp gpios support and we were already not building
axp-gpio support for the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
All sunxi boards now use the driver-model, so remove the non driver-model
code.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Now that we've everything prepared for it remove the DM settings from the
defconfig(s) and simply always set them for sunxi.
This makes all sunxi boards allways use the driver model for gpios and
ethernet, and allows us to move over more bits to the driver-model without
the need to introduce #ifdef-ery for boards which are not yet using DM.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
u-boot has support for a number of boards for which a dts file still needs
to be written, add minimal dts files for these boards so that we can switch
them over to driver-model / fdt.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We need dts files for all boards we support, so bring in a few unmerged ones,
these will be replaced with the upstream merged versions the next time we
sync dts files.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Bring all the sunxi dts files (and update existing ones) from
mripard/sunxi/dt-for-4.1 (which will be merged into upstream master any
day now). This is necessary so that we can move all sunxi boards over to
the driver model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Modify the sunxi-emac eth driver to support driver model.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
netdev.h should not be included in driver-model enabled builds (doing so
causes compiler warnings about struct eth_driver not being declared), but
we do use sunxi_gmac_initialize in the driver-model case, so move it out of
netdev.h .
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add driver-model support to the axp_gpio code, note that this needs a small
tweak to the driver-model version of sunxi_name_to_gpio to deal with the
vbus detect and enable pins which are not standard numbered gpios.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the axp-gpio code out of the drivers/power/axp*.c code, and into
a new separate axpi-gpio driver.
This change drops supports for the gpio3 pin on the axp209, as that requires
special handling, and no boards are using it.
Besides cleaning things up by moving the code to a separate driver, as
a bonus this change also adds support for the (non vusb) gpio pins on the
axp221 and the gpio pins on the axp152.
The new axp-gpio driver gets its own Kconfig option, and is only enabled
on boards which need it. Besides that it only gets enabled in the regular
u-boot build and not for the SPL as we never need it in the SPL.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Add support for the axp152 and axp209 PMICs to the pmic register access
helpers. This is a preparation patch for moving the axp gpio code to a
separate gpio driver.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Move the register helpers used to access the registers via p2wi resp.
rsb bus on the otherwise identical axp221 and axp223 pmics to a separate
file, so that they can be used by the upcoming standalone axp gpio driver
too.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
The driver-model gpio functions may return another value then -1 as error,
make the sunxi usbc properly handle this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
Enable full support for the A33 SoC including display, otg-usb, etc.
Signed-off-by: Vishnu Patekar <vishnupatekar0510@gmail.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Ian Campbell <ijc@hellion.org.uk>
