This patch adds the possibility in both debug and ramfs modes to
optionally load an env file from /tftpboot/$tftppath (this is ignored if
not present, so the change is backward compatible). This gives the debug
and ramfs scripts the possibility to set uboot environment variables
that were previously asked the users to manually set (nfs path in debug
and rootfs size in ramfs).
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Tom Rini <trini@konsulko.com>
The tftppath was not set in case of run ramfs. It worked only by chance
if was already set before.
Also check the boardname before setting the tftppath for COGE5.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Tom Rini <trini@konsulko.com>
The CPUWD reset reason is used for kmp204x.
And the qrio cpu reset request is configured to operate in
core reset mode.
But for the evaluation of the qrio's reset reason register
the CPUWD figures as a unit reset source rather than a core
reset source. This patch defines the CPUWD reset as a core
reset source when evaluating the reset reason register.
Signed-off-by: Rainer Boschung <rainer.boschung@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
This patch moves the qrio and i2c deblocking code to
keymile/common as it will also be used by the upcoming CENT2 board.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
This prevents the board from booting which is not the expected behavior.
Signed-off-by: Valentin Longchamp <valentin.longchamp@ch.abb.com>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
CC: Priyanka Jain <priyanka.jain@nxp.com>
Take up maintainership of random number generator drivers with
Heinrich Schuchardt as the reviewer.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When using fitImage in AARCH64, the fdt is only 4 byte aligned.
According to linux kernel -> Documentation/arm64/booting.txt, the
fdt *must* be 8 byte aligned. Therefore, it is somewhat random,
if you build a kernel that the fdt is 4 or 8 byte aligned.
Removing fdt_high (or changing it to a valid 8 byte aligned
address) solves this issue.
Signed-off-by: Matthias Schoepfer <matthias.schoepfer@ithinx.io>
CC: Mateusz Kulikowski <mateusz.kulikowski@gmail.com>
This add the initial support of the broadcom reference
board bcm968360bg with a bcm68360 SoC.
This board has 512 MB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
As no gpio.h is defined for this architecture, to avoid
compilation failure, do not include <asm/arch/gpio.h> for
arch bcm68360.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
In order to generate a bootable U-Boot binary for i.MX8QXP MEK
we need to run:
$ make imx8qxp_mek_defconfig
$ make flash.bin
The resultant flash.bin and flash.log are not removed after
running 'make mrproper'.
Include these files into the CLEAN_FILES list entry so that
they can be properly deleted after 'make mrproper'.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Execute the command cls (for clear screen), when the "menu background"
keyword is present in extlinux.conf file, only if the command is supported.
This patch avoid the warning "Unknown command 'cls'"
with "menu background" in extlinux.conf when CONFIG_CMD_BMP is activated
and CONFIG_CMD_CLS not activated (default for CONFIG_DM_VIDEO).
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Correct some function comments. Convert to Sphinx style.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Allow reading compressed content from fit image, even if
CONFIG_SPL_OS_BOOT is not set.
This allow booting compressed 2nd stage u-boot from fit image.
Additionally, do not print warning message if compression node is not
found, since it simply implies the content is uncompressed.
Signed-off-by: Klaus H. Sorensen <khso@prevas.dk>
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
The ST-Ericsson U8500 SoC has been used in mass-production for
some Android smartphones released around 2012.
In particular, Samsung has released more than 5 different
smartphones based on U8500, e.g.
- Samsung Galaxy S III mini (GT-I8190) "golden"
- Samsung Galaxy S Advance (GT-I9070) "janice"
- Samsung Galaxy Xcover 2 (GT-S7710) "skomer"
and a few others.
Mainline Linux has great support for the Ux500 SoC, so these
smartphones can also run Linux mainline quite well.
Unfortunately, the original Samsung bootloader used on these devices
has limitations that prevent booting Linux mainline directly.
It keeps the L2 cache enabled, which causes Linux to crash very early,
shortly after decompressing the kernel.
Using U-Boot allows to circumvent these limitations. We can let the
Samsung bootloader chain-load U-Boot and U-Boot locks the L2 cache
before booting into Linux. U-Boot has several other advantages
- it supports device-trees directly and we are no longer limited to
flashing Android boot images through Samsung's proprietary download
mode.
The Samsung "stemmy" board covers all Samsung devices based on U8500.
Add minimal support for "stemmy". For now only UART is supported but
this will be extended later.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Add myself as maintainer for ST-Ericsson U8500 SoC to MAINTAINERS.
Linus Walleij usually reviews all Ux500 related patches,
so add him as a reviewer.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The NovaThor U8500 SoC was released by ST-Ericsson in 2011.
It was used for some development boards like the CALAO Systems
Snowball SBC, but mass production was primarily for Android
smartphones like the Samsung Galaxy S III mini.
Previous support for U8500 was removed in
commit 68282f55b8 ("arm: Remove unused ST-Ericsson u8500 arch")
since none of the boards were converted to generic boards
before the deadline.
The new code does not have much in common with the previous code.
I have completely rewritten everything, embracing the Driver Model
and device trees wherever possible.
The U8500 support is a bit more minimal for now - my primary
use case is to use U-Boot as alternative bootloader for some of the
U8500 Samsung smartphones. At the moment U-Boot is chain-loaded from
the original Samsung bootloader. A side effect of this is that we
can (temporarily) get away without implementing some functionality
- e.g. all clocks are already enabled by the original bootloader.
More functionality will be added in future patches.
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: John Rigby <john.rigby@linaro.org>
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
from https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson.git/
tag "ux500-armsoc-v5.6-2"
commit 224bf0fe7292 ("ARM: dts: ux500: samsung-golden: Add Bluetooth")
(queued for merge in Linux 5.6)
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
The Nomadik Multi Timer Unit (MTU) provides 4 decrementing
free-running timers. It is used in ST-Ericsson Ux500 SoCs.
The driver uses the first timer to implement UCLASS_TIMER.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
I'm also seeing the build failure that commit
7d4776545b env: solve compilation error in SPL
tried to fix, namely that the reference to env_flags_validate from
env_htab cannot be satisfied when flags.o is not built in. However,
that commit got reverted by
d90fc9c3de Revert "env: solve compilation error in SPL"
Necessary, but not sufficient conditions to see this are
CONFIG_SPL=y (obviously)
CONFIG_SPL_ENV_SUPPORT=n (so flags.o does not get compiled)
CONFIG_SPL_LIBCOMMON_SUPPORT=y (so env/built-in.o is part of the SPL link)
Now, these are satisfied for e.g. imx6q_logic_defconfig. But that
builds just fine, and spl/u-boot-spl.map lists .data.env_htab among
the discarded (garbage collected) sections. Yet, on our
mpc8309-derived board, we do see the build failure, so perhaps the
linker works a bit differently on ppc than on ARM, or there's yet some
other configuration option needed to observe the break.
This is another attempt at solving it, which also cleans up
env/Makefile a bit: Introduce a def_bool y symbol CONFIG_ENV_SUPPORT
which complements CONFIG_(SPL/TPL)_SUPPORT. Then use
CONFIG_$(SPL_TPL_)ENV_SUPPORT to decide whether to include the five
basic env/*.o files. For attr.o, flags.o and callback.o, this
shouldn't change anything. Also, common.o and env.o still get
unconditionally built for U-boot proper. But for TPL/SPL, those two
are only included if CONFIG_(SPL/TPL)_SUPPORT is set.
Having that symbol should also allow simplifying conditionals such as
#if !defined(CONFIG_SPL_BUILD) || CONFIG_IS_ENABLED(ENV_SUPPORT)
found in drivers/reset/reset-socfpga.c to just
CONFIG_IS_ENABLED(ENV_SUPPORT).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Clearfog Base carrier uses serdes lane #5 as USB host. Use EEPROM stored
device identification to configure the serdes accordingly when
available.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Select the serdes configuration table based on the platform identity
read from EEPROM TLV data. Clearfog GTR needs a slightly different
serdes configuration.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Set the kernel device-tree file (fdtfile environment variable) based on
run-time detection of the platform.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Read RAM die capacity from the EEPROM TLV.
Follow the ONIE standard that defines the Vendor Extension entry type
for vendor specific data. We have no Private Enterprise Number at the
moment as the standard requires. Use the dummy all 0xff value for now.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Add support for read/write of ONIE "Tlvinfo" EEPROM data format. TLV
stands for Type-Length-Value. The data format is described here:
https://opencomputeproject.github.io/onie/design-spec/hw_requirements.html#board-eeprom-information-format
Based on U-Boot patch from the Open Compute project:
ec87e872d4/patches/u-boot/common/feature-sys-eeprom-tlv-common.patch
Keep only I2C EEPROM support. Use the generic eeprom driver. Fix
checkpatch issues.
Add support for multiple EEPROM TLV stores on the same system. This is
useful in case of SOM and carrier that both provide ID and hardware
configuration information.
Add option to enable for SPL. This allows selection of RAM configuration
based on EEPROM stored board identification.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Add device-tree description for the EEPROM devices on Armada 388 SOM rev
2.1.
Another EEPROM is now on Clearfog Pro carrier rev 2.2, and Clearfog Base
rev 1.3.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Enabled both DDR clock signals to support Clearfog variants (currently,
Clearfog GTR) that need both clocks.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
DDR clock out might be unrelated to the number of active chip-select.
For example, the board might have two DDR components, but only one
chip-select. The clk_enable mask allows the board to enable DDR clocks
regardless of active chip-selects.
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
K3 J721E:
* DMA support.
* MMC and ADMA support.
* EEPROM support.
* J721e High Security EVM support.
* USB DT nodes
K3 AM654:
* Fixed boot due to pmic probe error.
* USB support and DT nodes.
* ADMA support
DRA7xx/AM57xx:
* BBAI board support
* Clean up of net platform code under board/ti
AM33/AM43/Davinci:
* Reduce SPL size for omap3 boards.
* SPL DT support for da850-lcdk
* PLL divider fix for AM335x
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/toradex/colibri-imx8x/colibri-imx8x.c:104:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/toradex/apalis-imx8/apalis-imx8.c:92:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qxp_mek/imx8qxp_mek.c:115:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:102:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
detail_board_ddr_info() is not used anywhere, so simply remove it.
This function is only used by Layerscape, not by i.MX.
This was detected by the following sparse warning:
board/advantech/imx8qm_rom7720_a1/imx8qm_rom7720_a1.c:110:6: warning: no previous
prototype for ‘detail_board_ddr_info’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Oliver Graute <oliver.graute@kococonnector.com>
Include fdt_support.h header file to fix the following sparse warning:
board/freescale/imx8qm_mek/imx8qm_mek.c:116:5: warning: no previous
prototype for ‘ft_board_setup’ [-Wmissing-prototypes]
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
