Previous versions used full wait states for the chip select #1 which
is connected to the Xilinix SystemACE controller on the AMCC Katmai
evaluation board. This leads to really slow access and therefore low
performance. This patch now sets up the chip select a lot faster
resulting in much better read/write performance of the Linux driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Now 405EZ ports also show upon bootup from which boot device
they are configured to boot:
U-Boot 1.2.0-gd3832e8f-dirty (Apr 18 2007 - 07:47:05)
CPU: AMCC PowerPC 405EZ Rev. A at 199.999 MHz (PLB=133, OPB=66, EBC=66 MHz)
Bootstrap Option E - Boot ROM Location EBC (32 bits)
16 kB I-Cache 16 kB D-Cache
Board: Acadia - AMCC PPC405EZ Evaluation Board
Signed-off-by: Stefan Roese <sr@denx.de>
U-Boot part of Lite5200b low power mode support.
Puts SDRAM out of self-refresh and transfers control to
address saved at physical 0x0.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Fix bug introduced by "Fix get_partition_info() parameter error in all
other calls" from 2005-03-04 in cmd_ide.c and cmd_scsi.c, which prevented
to use diskboot or scsiboot form another device than 0.
Signed-off-by: Denis Peter <d.peter@mpl.ch>
This patch fixes changes the i2c_init(...) function to use the function
get_OPB_freq() rather than calculating the OPB speed by
sysInfo.freqPLB/sysInfo.pllOpbDiv. The get_OPB_freq() function is
specific per processor. The prior method was not and so was calculating
the wrong speed for some PPC4xx processors.
Signed-off-by: Jeffrey Mann <mannj@embeddedplanet.com>
Signed-off-by: Stefan Roese <sr@denx.de>
With this new base address of the Xilinx SystemACE controller
the Linux driver will be easier to adapt, since it can now be
mapped via the "normal" ioremap() call.
Signed-off-by: Stefan Roese <sr@denx.de>
The fdt command uses David Gibson's libfdt library to manipulate as well
as print the flattened device tree. This patch is the new command,
the second part is the modifications to the existing code.
Enhanced the formerly private function _fdt_next_tag() to allow stepping
through the tree, used to produce a human-readable dump, and made
it part of the published interface.
Also added some comments.
The board specific "bootstrap" command is now fixed and can
be used for the AMCC Katmai board to configure different
CPU/PLB/OPB frequencies.
Signed-off-by: Stefan Roese <sr@denx.de>
Fix a bug in the auto calibration routine. This driver now runs
more reliable with the tested modules. It's also tested with
167MHz PLB frequency (667MHz DDR2 frequency) on the Katmai.
Signed-off-by: Stefan Roese <sr@denx.de>
The "old" i2c commands (iprobe, imd...) are now compiled in again,
even when the i2c command tree is enabled via the CONFIG_I2C_CMD_TREE
config option.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch adds some 4xx GPIO functions. It also moves some of the
common code and defines into a common 4xx GPIO header file.
Signed-off-by: Stefan Roese <sr@denx.de>
Prevent false interrupt from hanging Linux as MSR[EE] is set
to enable interrupts by changing the PIC out of the default
pass through mode into mixed mode.
Signed-off-by: Haiying Wang <haiying.wang@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Also fixes some commmand for 8641 HPCN ramboot case.
Signed-off-by: Jason Jin <jason.jin@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Without this patch, I am unable to get to the prompt on rev 2 silicon.
Only set ddrioovcr for rev1.
Signed-off-by: Ed Swarthout<ed.swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
