Commit graph

878 commits

Author SHA1 Message Date
Peng Fan
4230d68aa8 imx: imx8mq: default select CLK_IMX8MQ
Since the power domain driver default select CONFIG_CLK, so we will
meet lots failures without CLK_IMX8MQ, so default select it.

Fixes: commit 4eb82c2e56 ("imx: power-domain: Get rid of SMCCC dependency")
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-06-03 11:15:24 -04:00
Marek Vasut
4d573d5c98 ARM: dts: imx: Add support for DH electronics i.MX8M Plus DHCOM and PDK2
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-05-23 11:37:58 +02:00
Philip Oberfichtner
55d1537c5b bosch: Add initial board support for ACC
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.

The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.

[1] Commit 6192cf8ac082 from
    git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git

Signed-off-by: Philip Oberfichtner <pro@denx.de>
2022-05-20 12:36:48 +02:00
Michael Trimarchi
37a7c374a6 arm: mach-imx: cmd_nandbcb fix bad block handling
The badblock should be skipped properly in reading and writing.
Fix the logic. The bcb struct is written, skipping the bad block,
so we need to read using the same logic. This was tested create
bad block in the area and then flash it and read it back.

Acked-by: Han Xu <han.xu@nxp.com>
Tested-By: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2022-05-20 12:36:48 +02:00
Ye Li
cda8f87349 caam: Fix crash in case caam_jr_probe failed
If probing caam_jr returns failure, the variable "dev" will not be
initialized, so we can't use dev->name for the error print.
Otherwise it will cause crash.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
2022-05-20 12:36:47 +02:00
Peng Fan
a1d675ac77 imx: imx8m: drop uneeded check
All i.MX8M needs TZASC ID SWAP set and locked, no need the check to
waste cpu cycles.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
2022-05-20 09:30:28 +02:00
Peng Fan
5dd9db8f7d imx: imx8m: add rproc_att
With rpoc_att, bootaux able to kick elf file for M core

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:28 +02:00
Peng Fan
40153df63a imx: bootaux: get stack from elf file
To i.MX8, M core stack is pre-coded in source code, so need to get it
before kicking M core. The stack pointer is stored in the first word of
the first PT_LOAD section __isr_vector. So use a num to index the
section loading.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:28 +02:00
Peng Fan
fd60a87e75 imx: bootaux: add missing newline
Add missing newline

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:28 +02:00
Peng Fan
56c2dbdaba imx: bootaux: cleanup code
Use if (CONFIG_IS_ENABLED()) to make code cleaner
Enable elf support for i.MX8M

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-05-20 09:30:28 +02:00
Fabio Estevam
d175982c20 imx8mn/8mp: Allow booting via USB
When trying to boot via USB on i.MX8MN it is necessary to specify
the U-Boot environment location, otherwise the boot process simply
hangs.

Specify the environment location when booting from USB.

Tested on a imx8mn-evk.

Suggested-by: Michael Nazzareno Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Tested-By: Tim Harvey <tharvey@gateworks.com>
2022-05-19 21:39:36 +02:00
Tom Rini
6e2af641e4 u-boot-imx-20220422
-------------------
 
 - Switch to DM_SERIAL
 - Drop MMCROOT
 - several cleanup
 
 CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11815
 -----BEGIN PGP SIGNATURE-----
 
 iG0EABECAC0WIQS2TmnA27QKhpKSZe309WXkmmjvpgUCYmJq1Q8cc2JhYmljQGRl
 bnguZGUACgkQ9PVl5Jpo76ZlxQCfQNPkQVf10kjENID/D9mu+Hl2tMEAnj8AMOyF
 iQrcw6oegrVvZZXV+s2J
 =XjAE
 -----END PGP SIGNATURE-----

Merge tag 'u-boot-imx-20220422' of https://gitlab.denx.de/u-boot/custodians/u-boot-imx

u-boot-imx-20220422
-------------------

- Switch to DM_SERIAL
- Drop MMCROOT
- several cleanup

CI: https://source.denx.de/u-boot/custodians/u-boot-imx/-/pipelines/11815
2022-04-22 08:12:20 -04:00
Ye Li
0b0cd1536a imx: Fix build error
Fix wrong environment.h and remove DECLARE_GLOBAL_DATA_PTR

Fixes: 30e39ac7c9 (imx: imx7 Support for Manufacturing Protection)
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
2022-04-21 15:18:25 +02:00
Ye Li
92aff90b1e imx: Update FSL_MFGPROT config for iMX8M
Update the Kconfig and Makefile to allow build for iMX8M and
restrict the build only in u-boot.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Gaurav Jain <gaurav.jain@nxp.com>
2022-04-21 15:18:25 +02:00
Marek Vasut
e4dc2d0620 ARM: imx: imx8m: env: Switch to arch_env_get_location()
Implement arch_env_get_location() instead of env_get_location(), so that
the env_get_location() can be implemented on board level and override the
arch_env_get_location() architecture defaults.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Adam Ford <aford173@gmail.com>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marek Behún <marek.behun@nic.cz>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tim Harvey <tharvey@gateworks.com>
Cc: Tom Rini <trini@konsulko.com>
Cc: Tommaso Merciai <tomm.merciai@gmail.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
2022-04-21 09:08:41 -04:00
Marek Vasut
74f88b7221 ARM: imx: imx8m: Fix board_get_usable_ram_top()
The 4 GiB boundary is at 0xffffffff+1 , not at 0x80000000, fix this.

The PHYS_SDRAM of i.MX8M is at 0x40000000 , so to restrict ram_top
below 4 GiB, the ram_top has to be set to 0xffffffff as it is not
an offset from the start of PHYS_SDRAM, but rather a physical address
marking the topmost allowed DRAM address.

Fixes: e27bddff4b ("imx8m: Restrict usable memory to space below 4G boundary")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Frieder Schrempf <frieder.schrempf@kontron.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
2022-04-21 14:38:03 +02:00
Tim Harvey
2395625209 board: gateworks: venice: add imx8mp-venice-gw740x support
The GW74xx is based on the i.MX 8M Plus SoC featuring:
 - LPDDR4 DRAM
 - eMMC FLASH
 - Gateworks System Controller
 - PCIe Gen 3.0 switch (build option)
 - USB 3.0 HUB
 - USB Type-C front panel connector
 - GPS
 - 3-axis accelerometer
 - CAN bus
 - 6x GbE RJ45 front-panel jacks
  - 1x IMX8M FEC RGMII GbE (with Passive PoE)
  - 5x IMX8M EQOS RGMII 6 port GbE Switch
    (1x with 802.3af class 5 Active PoE)
 - RS232/RS485/RS422 serial transceiver
 - MIPI header (DSI/CSI/GPIO/PWM/I2S)
 - DigI/O header (UART/GPIO/I2C/ADC)
 - 802.11ac WiFi
 - Bluetooth BLE
 - 3x MiniPCIe sockets with PCI/USB
 - 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
 - PMIC
 - Wide range DC input supply (8V to 60V DC)

Do the following to add support for this and future imx8mp-venice boards:
 - add dts
 - add DRAM config
 - add PMIC config
 - add IMX8MP support in spl.c and venice.c

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 12:44:24 +02:00
Tim Harvey
61cf225053 board: gateworks: gw_ventana: use comomn GSC driver
Use the common GSC driver.

This allows us to do some additional cleanup:
 - use the GSC driver functions
 - move waiting for the EEPROM to the SPL int (it will always be ready
   after this)
 - move eeprom functions into eeprom file and elimate GSC_I2C_BUS
 - eliminate some redundant EEPROM reads (the EEPROM must be read in
   SPL before relocation, in SPL after relocation, and in U-Boot init.
   All subsequent uses can use the global structure)
 - remove unnecessary header files and alphabatize includes

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 12:44:24 +02:00
Tim Harvey
fb9ec33878 board: gateworks: venice: use common GSC driver
Use the common GSC driver.

This allows us to do some additional cleanup:
 - rename gsc{.c,.h} to eeprom{.c.h} for clarity
 - collapse eeprom_get_dev
 - remove unnecessary header files and alphabatize includes

Signed-off-by: Tim Harvey <tharvey@gateworks.com>
2022-04-21 12:44:23 +02:00
Denys Drozdov
47bcc0d056 toradex: apalis-imx8x: drop support for apalis imx8x
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.

Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-21 12:44:23 +02:00
Loic Poulain
85d0580e68 imx8ulp: clock: Fix lcd clock algo
The div loop uses reassign and reuse parent_rate, which causes
the parent rate reference to be wrong after the first loop, the
resulting clock becomes incorrect for div != 1.

Fixes: 829e06bf41 ("imx8ulp: clock: Add MIPI DSI clock and DCNano clock")
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-04-21 12:44:23 +02:00
Marek Vasut
cb61b2fb2b ARM: imx: Get rid of only i.MX8M SMCCC arch call
This is the only place where i.MX8M code does SMCCC call, remove it.
The output has little value as it prints some part of commit ID, and
worse, if there is no SMC handler installed, the code outright hangs
or crashes the system.

By removing this one instance of SMCCC call, U-Boot no longer depends
on SMC handlers and can boot without hanging in any case. If there is
a need to dump this commit ID, use CMD_SMC instead and do 'smc' call
from U-Boot shell or scripts instead of hard-coding SMCCC dependency
into architecture code. This particular code can be replaced by:
 => smc 0xc2000003 0 0 0 0 0 0

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-13 09:35:45 +02:00
Marek Vasut
2fa763baa1 ARM: imx: Enable instruction cache early on on i.MX8M
Enable instruction cache early on to speed up the boot process on i.MX8M.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-13 09:35:33 +02:00
Marek Vasut
d7f72b6830 ARM: dts: imx8mm: Add i.MX8M Mini Toradex Verdin based Menlo board
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-12 21:08:23 +02:00
Marek Vasut
d072fdde53 ARM: imx: romapi: Repair FlexSPI NOR boot offset
The FlexSPI NOR boot offset does not require any special handling,
the image_offset is correct in either case (0x1000 for FlexSPI NOR
and 0x8000 for SD/eMMC) and the offset of u-boot.itb from the start
of flash.bin is always 0x58000 on MX8MN/MX8MP, which matches the
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR * 512 - 0x8000 in case
CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR=0x300, which is always the
case on MX8MN/MX8MP.

The CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR is really overloaded in
case of the MX8MN/MX8MP, but fixing that needs additional plumbing.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-12 21:08:23 +02:00
Marek Vasut
bba6cc7018 ARM: dts: imx: Add support for Data Modul i.MX8M Mini eDM SBC
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.

Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
2022-04-12 19:10:44 +02:00
Ariel D'Alessandro
6c317fedc7 bsh: imx8mn-smm-s2/pro: Add iMX8MN BSH SMM S2 boards
Introduce BSH SystemMaster (SMM) S2 board family, which consists of:
iMX8MN SMM S2 and iMX8MN SMM S2 PRO boards.

Add support for iMX8MN BSH SMM S2 board:

- 256 MiB DDR3 RAM
- 512MiB Nand
- USBOTG1 peripheral - fastboot.
- 100Mbit Ethernet

Add support for iMX8MN BSH SMM S2 PRO board:

- 512 MiB DDR3 RAM
- 8 GiB eMMC
- USBOTG1 peripheral - fastboot.
- 100Mbit Ethernet

Signed-off-by: Ariel D'Alessandro <ariel.dalessandro@collabora.com>
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
2022-04-12 19:10:44 +02:00
Peng Fan
eace942951 imx8mq: soc: Set the BYPASS ID SWAP bit (GPR10 bit 1)
Set the BYPASS ID SWAP bit (GPR10 bit 1).
The ID SWAP function randomly make TZASC grant non-secure access to
secure memory. TZASC ID SWAP should be bypassed by setting the bit
TZASC_ID_SWAP_BYPASS(bit 1) in IOMUX_GPR10 register.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:44 +02:00
Ye Li
1c9bc0fffa imx8m: soc: Relocate u-boot to the top DDR in 4GB space
The EFI memory init uses gd->ram_top for conventional memory. In
current implementation, the ram_top is below optee address. This cause
grub failed to allocation memory for initrd.
The change updates DDR bank setup functions to place the u-boot at top
DDR in 4GB space.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:44 +02:00
Peng Fan
1166bd433a imx8m: soc: drop phy-reset-gpios for fec
Need to drop phy-reset-gpios before booting linux, this property
is legacy property and replaced with reset-gpios.

If provide both, kernel would failed to request the same gpio twice
and cause fec not work.

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:44 +02:00
Peng Fan
8325ef3d77 imx: imx8m: soc: runtime drop extcon property from usbotg node
The extcon is an decrepted property and not used by upstream Linux and
NXP 5.10 kernel, so we remove it before kicking linux in case it is in
dts. Otherwise distro kernel will not able to have usb function.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:44 +02:00
Peng Fan
35bb60787b imx: imx8mp: disable fused IP for UltraLite
Beside the fused modules on iMX8MP Lite, this part has also fused
GPU3D/2D, LVDS and MIPI DSI.
So we have to disable them for kernel and also disable MIPI DSI
in u-boot DTS for splash screen at runtime.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:44 +02:00
Peng Fan
36bfd71c92 imx: imx8mp: detect i.MX8MP UltraLite when get cpu rev
Detect i.MX8MP UltraLite in get_cpu_variant_type

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:43 +02:00
Peng Fan
fd437083b8 imx: imx8mp: Add iMX8MP UltraLite Part cpu type
Add i.MX8MP UltraLite Part CPU type

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:43 +02:00
Francesco Dolcini
aa42894471 mx6: ddr: Wait before issuing the first MRS cmd
Wait 1ms before issuing the first MRS command to write DDR3 Mode
registers.

There is a requirement to wait a minimum time before issuing command to
the DDR3 device, according to the JEDEC standard this time is 500us
(after RESET_n is de-asserted until CKE becomes active) + tXPR (Reset
CKE Exit time, maximum value 360ns).

It seems that for some reason this is not enforced by the MMDC
controller.

Without this change we experienced random memory initialization failures
with about 2% boot failure rate on specific problematic boards, after
this change we were able to do more than 10.000 power-cycle without a
single failure.

Fixes: fe0f7f7842 ("mx6: add mmdc configuration for MX6Q/MX6DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-12 19:10:43 +02:00
Francesco Dolcini
09dbac8174 mx6: ddr: Restore ralat/walat in write level calibration
The current DDR write level calibration routine always overwrite
the ralat/walat fields to their maximum value, just save
the existing values at the beginning of the calibration routine
and restore it at the end.

In case the delay is estimated by the user to be more than one cycle the
walat should be configured according to that, this is not
automatically done.  From the i.MX6 RM:

   The user should read the results of the associated delay-line at
   MPWLDECTRL#[WL_DL_ABS_OFFSET#] and in case the user estimates that the
   reasonable delay may be above 1 cycle then the user should indicate it at
   MPWLDECTRL#[WL_CYC_DEL#]. Moreover the user should indicate it in
   MDMISC[WALAT] field. For example, if the result of the write leveling calibration
   is 100/256 parts of a cycle, but the user estimates that the delay is above 2 cycles
   then MPWLDECTRL#[WL_CYC_DEL#] should be configured to 2, so the total
   delay will be 2 and 100/256 parts of a cycle

Probably it would just possible to not overwrite the mdmisc register in
the first place, since this is not present in the write_level_calib() example
in NXP AN4467 nor in the i.MX6 RM (44.11.6.1 Hardware Write Leveling
Calibration).

Fixes: d339f16911 ("arm: imx6: Add DDR3 calibration code for MX6 Q/D/DL")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-12 19:10:43 +02:00
Ye Li
c41ffaa253 imx: imx8ulp_evk: Enable multiple env storage devices
Enable multiple storages for u-boot env:
MMC or SPI flash or NOWHERE for usb
so u-boot can runtime select the storage flash according to boot device.

Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:43 +02:00
Ji Luo
112b777849 imx: imx8ulp: reserve tee memory
The TEE memory should be reserved when TEE is present, so need
to runtime update dram bank and memory information according to
tee present or not.

Signed-off-by: Ji Luo <ji.luo@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:43 +02:00
Peng Fan
8c453e9d3d imx: imx8ulp: enable wdog_ad interrupt in CMC1
Enable wdog_ad interrupt being triggered by CMC1 to CM33 to let CM33
know A35 reset and reinitialize rpmsg.
Clear wdog_ad and AD_PERIPH reset interrupt after A35 up, otherwise
M33 will always receive interrupt.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 19:10:43 +02:00
Ye Li
c916fb1747 imx: imx8ulp: Change LPAV assignment for dual boot
Assign the LPAV owner to RTD, and assign LPAV masters and peripherals
to APD. So except the masters and peripherals, other resources
(like DDR, cgc2, pcc5) in LPAV won't be reset during reboot and suspend.

No needs to initialize DDR again after reboot.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Peng Fan
c628016c12 imx: imx8ulp: enable MU0_B clk by default
Enable MU0_B clk by default. When M33 image is loaded by Jlink,
the previous method not enable MU0_B clk and not able to communicate
with M33, so let's enable it by default.

And we not put it under kernel dts, because it conflicts with i.MX8QM
suspend/resume logic which requires large change.

Reviewed-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Jacky Bai <ping.bai@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Ye Li
509b8e7ba1 imx: imx8ulp: cgc: Switch to NICLPAV to FRO192 before PLL4 init
When reset with dual boot mode, the LPAV domain won't power down
due to its master is not assigned to APD. So the NICLPAV keeps the
last setting to use PLL4PFD1. So before SPL initialize the PLL4,
we need to switch NICLPAV to FRO192, otherwise system will hang.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Ye Li
4ab38f6822 imx: imx8ulp_evk: Skip init DDR for reboot in dual boot mode
When M33 is LPAV owner in dual boot, DDR, PCC5, CGC2 won't be reset
during APD reset. So no need to init DDR again after reboot, but need to
reconfigure the PLL4 PFD/PFDDIV/LPAV NIC etc, because kernel may
change or disable some of them.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Peng Fan
a092f33305 imx: imx8ulp: add ND/LD clock
Add a new ddr script, defconfig for ND
Configure the clock for ND mode
changing A35 to 960MHz for OD mode
Update NIC CLK for the various modes
Introduce clock_init_early/late, late is used after pmic voltage
setting, early is used in the very early stage for upower mu, lpuart and
etc.

Note: NIC runs at 324MHz, 442MHz has some random kernel hang issue with
cpuidle enabled now.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Peng Fan
40d60ec780 imx: imx8ulp: add CAAM clock entry
Add CAAM clock entry in PCC3

Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Clark Wang
a178a8c5de imx: imx8ulp: clock: Add clock support for i3c controller
Add i3c controller clock enable/disable function for imx8ulp.

Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Ye Li
5579d66e37 imx: imx8ulp: Add M33 handshake functions
Add functions to check if M33 image is booted and handshake with M33
image via MU. A core notifies M33 to start init by FCR F0, then wait
M33 init done signal by checking FSR F0.

Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:56 +02:00
Clément Péron
1697638e71 arm: imx: parse-container: add some missing end of line
Some printf() have strings that doesn't terminate with end of line
and make the output hard to read.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 17:33:55 +02:00
Marek Vasut
e26d0152d6 ARM: imx: Decode ECSPI env location from i.MX8M ROMAPI tables
Decode ECSPI boot device in env_get_location() from i.MX8M ROMAPI tables.
This is necessary to correctly identify env is in SPI NOR when the system
boots from SPI NOR attached to ECSPI.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-04-12 17:33:55 +02:00
Ye Li
0f709635fd imx8ulp: Disable SPL exception vector
Disable SPL exception vector which causes issue to ROM patch execution
when SPL calling ROM API.

Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
2022-04-12 15:36:18 +02:00