Commit graph

68 commits

Author SHA1 Message Date
Joe Hershberger
1fd92db83d net: cosmetic: Fix var naming net <-> eth drivers
Update the naming convention used in the network stack functions and
variables that Ethernet drivers use to interact with it.

This cleans up the temporary hacks that were added to this interface
along with the DM support.

This patch has a few remaining checkpatch.pl failures that would be out
of the scope of this patch to fix (drivers that are in gross violation
of checkpatch.pl).

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:33 -06:00
Joe Hershberger
0adb5b761f net: cosmetic: Name ethaddr variables consistently
Use "_ethaddr" at the end of variables and drop CamelCase.
Make constant values actually 'const'.

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Acked-by: Simon Glass <sjg@chromium.org>
2015-04-18 11:11:32 -06:00
Jeroen Hofstee
84f64c8bbe net: fec_mxc: make local functions static
Signed-off-by: Jeroen Hofstee <jeroen@myspectrum.nl>
2014-10-25 07:02:02 -04:00
Fabio Estevam
f599288d55 net: fec_mxc: Poll FEC_TBD_READY after polling TDAR
When testing the FEC driver on a mx6solox we noticed that the TDAR bit gets
always cleared prior then the READY bit is cleared in the last BD, which causes
FEC packets reception to always fail.

As explained by Ye Li:

"The TDAR bit is cleared when the descriptors are all out from TX ring, but on
mx6solox we noticed that the READY bit is still not cleared right after TDAR.
These are two distinct signals, and in IC simulation, we found that TDAR always
gets cleared prior than the READY bit of last BD becomes cleared.
In mx6solox, we use a later version of FEC IP. It looks like that this
intrinsic behaviour of TDAR bit has changed in this newer FEC version."

Fix this by polling the READY bit of BD after the TDAR polling, which covers the
mx6solox case and does not harm the other SoCs.

No performance drop has been noticed with this patch applied when testing TFTP
transfers on several boards of different i.mx SoCs.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-09-09 15:06:12 +02:00
Fabio Estevam
db5b7f566e net: fec_mxc: Adjust RX DMA alignment for mx6solox
mx6solox has a requirement for 64 bytes alignment for RX DMA transfer.
Other SoCs work with the standard 32 bytes alignment.

Adjust it accordingly by using 64 bytes aligment in the FEC RX DMA buffers,
which addresses the needs from mx6solox and also works for the other SoCs.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
2014-09-09 15:05:37 +02:00
Markus Niebel
6ba45cc0f8 NET: fec_mxc: fix MDIO clock prescaler calculation
The prescaler value for MDC is calculated wrong for
MX6S. Implement the same logic as linux here which handles
ENET_MAC different then original FEC.

Tested on a custom board with i.MX6S and 100MBit PHY

Signed-off-by: Markus Niebel <Markus.Niebel@tqs.de>
2014-02-11 11:33:45 +01:00
Marek Vasut
79e5f27b09 Net: FEC: Fix huge memory leak
The fec_halt() never free'd both RX and TX DMA descriptors that
were allocated in fec_init(), nor did it free the RX buffers.
Rework the FEC driver so that these descriptors and buffers are
allocated only once in fec_probe().

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
2013-11-21 16:32:29 +01:00
Fabio Estevam
fd37f195ca net: fec_mxc: Fix timeouts during tftp transfer
Performing tftp transfers on mx28 results in random timeouts.

Hector Palacios and Robert Hodaszi analyzed the root cause being related to the
wrong alignment of the 'buff' buffer inside fec_recv().

Benoît Thébaudeau provided an excellent analysis of the alignment bug that is
present on older versions, such as GCC 4.5.4:

http://marc.info/?l=u-boot&m=137942904906131&w=2

Use ALLOC_CACHE_ALIGN_BUFFER() to avoid alignment issues from older GCC
versions.

Reported-by: Hector Palacios <hector.palacios@digi.com>
Tested-by: Oliver Metz <oliver@freetz.org>
Tested-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2013-09-20 17:55:37 +02:00
Fabio Estevam
7df51fd8be net: fec_mxc: Add support for mx6 solo-lite
Similarly as mx25 and mx53, mx6solo-lite needs to setup the MII gasket for RMII
mode.

Add support for mx6solo-lite.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
2013-09-20 17:55:36 +02:00
Eric Nelson
ddb636bd66 fec_mxc: set ethaddr if fuses burned and not previously set
Without this change, the following message is generated:
	Warning: FEC using MAC address from net device

See doc/README.enetaddr for details.

Signed-off-by: Eric Nelson <eric.nelson@boundarydevices.com>
2013-08-21 19:20:28 +02:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Marek Vasut
ab94cd491f net: fec: Avoid MX28 bus sync issue
The MX28 multi-layer AHB bus can be too slow and trigger the
FEC DMA too early, before all the data hit the DRAM. This patch
ensures the data are written in the RAM before the DMA starts.
Please see the comment in the patch for full details.

This patch was produced with an amazing help from Albert Aribaud,
who pointed out it can possibly be such a bus synchronisation
issue.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Albert ARIBAUD <albert.u.boot@aribaud.net>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
Tested-by: Alexandre Pereira da Silva <aletes.xgr@gmail.com>
2013-07-12 09:29:32 +02:00
Marek Vasut
3104ce1f6f net: fec: Remove bogus flush_dcache_range() call
Remove incorrectly called and duplicate flush_dcache_range() call
from fec_mxc driver. The call is not needed, since the caches are
already flushed in fec_tbd_init(), moreover the second argument should
be the ending address, not size.

Signed-off-by: Marek Vasut <marex@denx.de>
Reported-by: Albert Aribaud <albert.u.boot@aribaud.net>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Tom Rini <trini@ti.com>
2013-07-12 09:26:08 +02:00
Alison Wang
bcb6e9023a net: fec_mxc: Add support for Vybrid VF610
This patch adds FEC support for Vybrid VF610 platform.

In function fec_open(), RCR register is only set as RGMII mode. But RCR
register should be set as RMII mode for VF610 platform.
This configuration is already done in fec_reg_setup(), so this piece of
code could just leave untouched the FEC_RCNTRL_RGMII / FEC_RCNTRL_RMII /
FEC_RCNTRL_MII_MODE bits.

Signed-off-by: Alison Wang <b18965@freescale.com>
Reviewed-by: Benoit Thebaudeau <benoit.thebaudeau@advansee.com>
Reviewed-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
2013-06-03 10:56:53 +02:00
Troy Kisky
fe428b909b net: fec_mxc: get phydev before fec_probe
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:51 +01:00
Troy Kisky
4dc27eed52 net: fec_mxc: only call phy_connect in fec_probe
This allows us to create the phydev before calling
fec_probe in later patch.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
ef8e3a3bbf net: fec_mxc: use fec_set_dev_name to set name
This allows us to create the phydev before calling
fec_probe in later patch.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
eef2448039 net: fec_mxc: have fecmxc_initialize call fecmxc_initialize_multi
Having only one call to fec_probe will ease the changing of its
parameters.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
575c5cc06f net: fec_mxc: change fec_mii_setspeed parameter
Only the hardware ethernet registers are needed
for this function, so don't pass the more general
structure. I'm trying to separate MII and fec.

This also fixes MX28 fec_mii_setspeed use on secondary ethernet port

This was found by inspection of the code and should be
checked on real hardware.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Troy Kisky
09439c3197 net: fec_mxc: delete CONFIG_FEC_MXC_MULTI
It is more logical to test for CONFIG_FEC_MXC_PHYADDR
to determine whether to define the function fecmxc_initialize.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2013-01-28 06:57:50 +01:00
Marek Vasut
c0b5a3bbb0 FEC: Replace magic contants
Replace the magic contant 1 << 24 with properly defined bits.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2012-09-27 12:22:10 -05:00
Marek Vasut
67449098a8 FEC: Rework the TX wait mechanism
The mechanism waiting for transmission to finish in fec_send() now
relies on the E-bit being cleared in the TX buffer descriptor. In
case of data cache being on, this means invalidation of data cache
above this TX buffer descriptor on each test for the E-bit being
cleared.

Apparently, there is another way to check if the transmission did
complete. This is by checking the TDAR bit in the X_DES_ACTIVE
register. Reading a register does not need any data cache invalidation,
which is beneficial.

Rework the sequence that wait for completion of the transmission so that
the TDAR bit is tested first and afterwards check the E-bit being clear.
This cuts down the number of cache invalidation calls to one.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2012-09-27 12:22:10 -05:00
Marek Vasut
bc1ce150b9 FEC: Remove endless loop in the FEC driver
The FEC hardware sometimes errors out on data transfer and hangs in
the tightloop adjusted by this patch. So add timeout into the tightloop
to make such a hang recoverable.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Otavio Salvador <otavio@ossystems.com.br>
Cc: Stefano Babic <sbabic@denx.de>
2012-09-27 12:22:09 -05:00
Marek Vasut
efe24d2e17 FEC: Properly align address over the buffers for cache ops
Align the address that's to be invalidated/flushed properly.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
2012-09-27 12:22:09 -05:00
Marek Vasut
e2a66e6097 FEC: Do not pass unaligned buffer to network stack
Do not pass unaligned RX buffer to the upper layers. The upper layer,
especially in the ARP case, recycles the buffer and passes it back into
the FEC, into it's TX path. With caches enabled, the FEC hangs on this
from time to time.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Benoit Thebaudeau <benoit.thebaudeau@advans>
Cc: Eric Nelson <eric.nelson@boundarydevices.com>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Fabio Estevam <fabio.estevam@freescale.com>
2012-09-27 12:22:09 -05:00
benoit.thebaudeau@advans
f41471e6a3 net: fec_mxc: Fix MDC for xMII
The MDC signal is available on all xMII (i.e. 'not 7-wire') interfaces, so
mii_speed has to be set for all these interfaces, and not only for MII.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-07-19 11:46:19 -05:00
benoit.thebaudeau@advans
9d2d924a0a net: fec_mxc: Fix setting of RCR for xMII
At least on i.MX25, the RMII mode did not work, which is fixed by this patch.

The MII_MODE bit of the FEC RCR register means xMII, i.e. 'not 7-wire', so set
it accordingly.

According to the xMII and 7-wire (aka GPSI) standards, full duplex should be
available on xMII, but not on 7-wire, so set FCE accordingly. The FEC may
support full duplex for 7-wire too, but the reference manual does not say that,
so avoid an invalid assumption. Actually, the choice between half and full
duplex also depends on the endpoint/switch/repeater configuration, so a config
option could be added for that, but there has been no need for it so far.

Signed-off-by: Benoît Thébaudeau <benoit.thebaudeau@advansee.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
2012-07-19 11:46:13 -05:00
Timur Tabi
11af8d6527 net: abort network initialization if the PHY driver fails
Now that phy_startup() can return an actual error code, check for that error
code and abort network initialization if the PHY fails.

Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Nobuhiro Iwamamatsu <nobuhiro.iwamatsu.yj@renesas.com> (sh_eth part)
Acked-by: Stephan Linz <linz@li-pro.net> (Xilinx part, xilinx_axi_emac and xilinx_ll_temac)
Reviewed-by: Marek Vasut <marex@denx.de> (FEC part)
2012-07-11 13:15:30 -05:00
Joe Hershberger
442dac4c7f drivers/net/fec_mxc.c: Fix compile warning
Fix this:
fec_mxc.c: In function 'fec_probe':
fec_mxc.c:926:13: warning: assignment from incompatible pointer type

Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Cc: Joe Hershberger <joe.hershberger@gmail.com>
2012-05-22 10:18:16 -05:00
Marek Vasut
a5990b2674 FEC: Abstract out register setup
Abstract out common register setup. This also configured r_cntrl
to correct value at registration time.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
2012-05-15 08:31:35 +02:00
Stefano Babic
b774fe9d8a NET: fec_mxc.c: Add a way to disable auto negotiation
Signed-off-by: Stefano Babic <sbabic@denx.de>
CC: Fabio Estevam <fabio.estevam@freescale.com>
2012-05-15 08:31:30 +02:00
Eric Nelson
5c1ad3e6f8 net: fec_mxc: allow use with cache enabled
Ensure that transmit and receive buffers are cache-line aligned.
Invalidate cache for each packet as received, update receive buffer
descriptors one cache line at a time, flush cache before transmitting.

Original patch by Marek:
 http://lists.denx.de/pipermail/u-boot/2012-February/117695.html

Signed-off-by: Eric Nelson <eric.nelson at boundarydevices.com>
Acked-by: Marek Vasut <marex@denx.de>
Tested-by: Marek Vasut <marex@denx.de>
2012-03-29 07:57:20 +02:00
Troy Kisky
13947f43c9 net: fec_mxc: add PHYLIB support
Surround non PHYLIB routines miiphy_restart_aneg
and miiphy_wait_aneg with ifndef CONFIG_PHYLIB.
When later PHYLIB is required it is easy to delete
the non-PHYLIB code. This separation idea
came from Andy Fleming.

fec_miiphy_read, and fec_miiphy_write changed to
fec_phy_read, and fec_phy_write with argument changes.

Deprecated miiphy_register is no longer used. Both
old and new PHYLIB code now use mdio_register.

Cleanup some debug prints.

Inline function fec_miiphy_fec_to_eth is no longer necessary.
Moved to the single call location.

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
2012-02-27 21:19:24 +01:00
Troy Kisky
28774cbaac net: fec_mxc: add 1000 Mbps selection
Define FEC_QUIRK_ENET_MAC and add to
arch-mx6/imx-regs.h

Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
Acked-by: Dirk Behme <dirk.behme@de.bosch.com>
2012-02-27 21:19:24 +01:00
Fabio Estevam
be252b654a net: imx: Add multi-FEC support for imx_get_mac_from_fuse
Add multi-FEC support for imx_get_mac_from_fuse by passing dev_id as a parameter.

This feature is important on mx28 SoC for example that has two FEC ports.

Cc: Ben Warren <biggerbadderben@gmail.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:09 +01:00
Jason Liu
2ef2b95095 fec: add the i.mx6q enet driver support
Cc: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jason Liu <jason.hui@linaro.org>
Acked-by: Stefano Babic <sbabic@denx.de>
2012-01-16 08:40:08 +01:00
Marek Vasut
be7e87e2dd FEC: Add support for iMX28 quirks
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-11-11 11:36:56 +01:00
Marek Vasut
eda959f340 GCC4.6: Squash warnings in fec_mxc.c
fec_mxc.c: In function 'fec_mii_setspeed':
fec_mxc.c:112:2: warning: format '%#lx' expects type 'long unsigned int', but
argument 2 has type 'u32'
fec_mxc.c: In function 'fec_recv':
fec_mxc.c:632:2: warning: format '%x' expects type 'unsigned int', but argument
2 has type 'long unsigned int'

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Mike Frysinger <vapier@gentoo.org>
2011-10-27 23:54:08 +02:00
Marek Vasut
17fb268cf7 FEC: Squish "got MAC from fuse" message, make it debug()
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:02 +02:00
Marek Vasut
e382fb4873 FEC: Add timeout for chip reset
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:02 +02:00
Marek Vasut
2e5f44213f FEC: Allow registering MII postconfiguration callback
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:02 +02:00
Marek Vasut
9e27e9dca1 FEC: Allow multiple FECes
This patch allows user to register multiple FEC controllers. To preserve
compatibility with older boards, the mxcfec_register() call is still in place.
To use multiple controllers, new macro is in place, the mxcfec_register_multi(),
which takes more arguments. The syntax is:

mxcfec_register_multi(bd, FEC ID, FEC PHY ID on the MII bus, base address);

To disable the fecmxc_register() compatibility stuff, define the macro
CONFIG_FEC_MXC_MULTI. This will remove the requirement for defining IMX_FEC_BASE
and CONFIG_FEC_MXC_PHYADDR.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:01 +02:00
Marek Vasut
d133b881b9 FEC: Abstract access to fec->eth in MII operations
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:01 +02:00
Marek Vasut
392b850233 FEC: Allow selection of MII mode via CONFIG_FEC_XCV_TYPE
The default is MII100, which was hardcoded previously in the driver.

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:01 +02:00
Marek Vasut
a50a90c90e FEC: Add RMII mode support
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:01 +02:00
Marek Vasut
9eb3770b7b FEC: Kill mode select FIXME's
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:01 +02:00
Marek Vasut
77dbd6ab7f FEC: Use defined constant instead of magic number
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:01 +02:00
Marek Vasut
879cf26130 FEC: Use proper accessor to read register in debug call
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Cc: Ben Warren <biggerbadderben@gmail.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Wolfgang Denk <wd@denx.de>
Cc: Detlev Zundel <dzu@denx.de>
2011-09-30 22:01:01 +02:00
Graeme Russ
a60d1e5b8e Timer: Fix misuse of ARM *timer_masked() functions outside arch/arm
Signed-off-by: Graeme Russ <graeme.russ@gmail.com>
2011-07-16 11:55:00 +02:00
Liu Hui-R64343
96912453fe fec_mxc: add support for MX53 processor
This patch add FEC support for Freescale MX53 processor

Signed-off-by: Jason Liu <r64343@freescale.com>
2011-02-02 00:54:41 +01:00