Radxa E25 is a network application carrier board for the Radxa CM3I SoM
with a RK3568 SoC. It features dual 2.5G ethernet, mini PCIe, M.2 B Key,
USB3, eMMC, SD, nano SIM card slot and a 26-pin GPIO header.
Features tested on a Radxa E25 v1.4:
- SD-card boot
- eMMC boot
- USB host
- PCIe/Ethernet adapters is detected
- SATA
Device tree is imported from linux next-20230728.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Tested-by: FUKAUMI Naoki <naoki@radxa.com>
rk3328-xhci has been added due to the fact that the upstream
dwc3 is unsupported. Moreover, the driver for rk3328-xhci is
not added to the code tree.
By considering these facts and unsupported rk3328-xhci this
patch is dropping all related code from DT. However, the DWC3
is fixed now in dwc3-generic and RK3328 USB 3.0 is functional
in upcoming patches.
Let's drop it.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
There is an Errata with the built-in I2C controller where various I2C
hardware errors cause a complete lockup of the CPU (which eventually
results in an watchdog reset).
Put the I2C MPP pins into GPIO mode and use the i2c-gpio driver instead.
This uses a bit-banged implementation of an I2C controller and avoids
triggering the Errata.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
ROCK 5A is a Rockchip RK3588S based SBC (Single Board Computer) by Radxa.
There are tree variants depending on the DRAM size : 4G, 8G and 16G.
Specifications:
Rockchip Rk3588S SoC
4x ARM Cortex-A76, 4x ARM Cortex-A55
4/8/16GB memory LPDDR4x
Mali G610MC4 GPU
MIPI CSI 2 multiple lanes connector
4-lane MIPI DSI connector
Audio – 3.5mm earphone jack
eMMC module connector
uSD slot (up to 128GB)
2x USB 2.0, 2x USB 3.0
2x micro HDMI 2.1 ports, one up to 8Kp60, the other up to 4Kp60
Gigabit Ethernet RJ45 with optional PoE support
40-pin IO header including UART, SPI, I2C and 5V DC power in
USB PD over USB Type-C
Size: 85mm x 56mm (Raspberry Pi 4 form factor)
Kernel commits:
d1824cf95799 ("arm64: dts: rockchip: Add rock-5a board")
991f136c9f8d ("arm64: dts: rockchip: Update sdhci alias for rock-5a")
304c8a759953 ("arm64: dts: rockchip: Remove empty line from rock-5a")
cda0c2ea65a0 ("arm64: dts: rockchip: Fix RX delay for ethernet phy on rk3588s-rock5a")
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Move bootph-all prop to common SoC dt file, because they are typically used
by multiple boards.
Unreferenced nodes are removed from the SPL device tree during a
normal build.
Suggested-by: Jonas Karlman <jonas@kwiboo.se>
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pcie pinctrl override added in the commit a76aa6ffa6 ("rockchip:
rk3568-rock-3a: Enable PCIe and NVMe support") is causing a pinmux issue
on linux when using a EFI boot flow.
The pcie reset-gpios must however be configured with gpio function, or
the device will freeze running pci enum and nothing is connected.
Adjust the pinctrl override in u-boot.dtsi to fix this issue. PCIe/NVMe
continues to work in both U-Boot and linux after this change.
Also revert disable of sdmmc2 and uart1 to fix use of wifi in linux when
using a EFI boot flow.
Fixes: a76aa6ffa6 ("rockchip: rk3568-rock-3a: Enable PCIe and NVMe support")
Fixes: 073d911ae6 ("rockchip: rk3568-rock-3a: Sync device tree from linux")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
The commit fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI
NOR flash") enabled SPI flash support by adding a spi0 alias.
Correct this by adding spi0-spi5 aliases in rk3588s-u-boot.dtsi and
SF_DEFAULT_BUS=5 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: fd6e425be2 ("rockchip: rk3588-rock-5b: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The commit 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI
NOR flash") enabled SPI flash support by overriding the spi0 alias.
Correct this by adding a new spi4 alias in rk356x-u-boot.dtsi and
SF_DEFAULT_BUS=4 and SPL_DM_SEQ_ALIAS=y in defconfig. Also enabled
support for parsing and auto discovery of parameters, SFDP.
Fixes: 64f79f88a7 ("rockchip: rk3568-rock-3a: Enable boot from SPI NOR flash")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also add CONFIG_ROCKCHIP_SPI_IMAGE=y to build a bootable SPI flash
image, u-boot-rockchip-spi.bin.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
TPL max size is limited to 184 KB, SPL is loaded to 0x0 and TF-A is
loaded to 0x40000, this limit SPL max size to 256 KB. With BootRom only
reading first 2 KB per 4 KB page of SPI flash, 880 KB may be needed for
TPL+SPL in a worst-case scenario. (184 KB + 256 KB) x 2 = 880 KB
Use 0xE0000 (896 KB) as the payload offset in SPI flash, this allows
for a payload of 3168 KB before env offset start to overlap.
Also remove CONFIG_LTO=y now that there is sufficient space for SPL in
SPI flash, and to fix a build issue reported by Peter Robinson.
Fixes: 5713135ecc ("rockchip: rockpro64: Build u-boot-rockchip-spi.bin")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Quentin Schulz <foss+u-boot@0leil.net>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
BootRom will try to load TPL+SPL from media in the following order:
- SPI NOR Flash
- SPI NAND Flash
- NAND Flash
- eMMC
- SDMMC
SPL will try to load FIT from media in the order defined in the device
tree u-boot,spl-boot-order property.
Change the default order to load FIT from to:
- same media as TPL+SPL
- SDMMC
- eMMC
Boards with strict load order requirements should override the
u-boot,spl-boot-order property in the board specific u-boot.dtsi.
Fixes: 42f67fb51c ("rockchip: rk3568: Fix boot device detection")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add bootph-all prop to common pinctrl nodes for eMMC, FSPI, SD-card and
UART2 that are typically used by multiple boards. Unreferenced nodes are
removed from the SPL device tree during a normal build.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz compute module is mostly pin-compatible with the RPi
CM4 form factor. Therefore, it can slot into the official Raspberry Pi
CM4 IO carrier board. Add this configuration to U-Boot.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Blade board is a carrier board for the SOQuartz
CM4-compatible compute module. It features PoE, an M.2 slot, an SD card
slot, HDMI, USB, serial and ethernet.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 SOQuartz Model A board is a carrier board for the SOQuartz
CM4-compatible compute module. It exposes PCIe, ethernet, USB, HDMI,
CSI, DSI, eDP and a 40 pin GPIO header, and is powered by 12V DC.
Features tested with a SOQuartz 4GB v1.1 2022-07-11:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model B is a credit-card sized single-board
computer based on the Rockchip RK3566 SoC. The board features an M.2
PCIe slot, USB3, USB2, eMMC, SD, ethernet, HDMI, analog audio out, a
40 pin GPIO header and a DSI and CSI port, as well as on-board Wi-Fi.
Features tested on a Quartz64-B 4GB v1.4 2022-06-06:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The Pine64 Quartz64 Model A is a single-board computer based on the
Rockchip RK3566 SoC. The board features USB3, SATA, PCIe, HDMI, USB2.0,
CSI, DSI, eDP, eMMC, SD, and an e-paper parallel port, as well as a
20 pin GPIO header.
Features tested on a Quartz64-A 8GB v2.0 2021-04-27:
- SD-card boot
- eMMC boot
- PCIe/NVMe/AHCI
- USB host
Device tree is imported from linux v6.4.
Co-developed-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Nicolas Frattaroli <frattaroli.nicolas@gmail.com>
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Remove regulator-boot-on prop from regulators now that the phy core has
support for phy-supply after the commit c57e0dcd93 ("phy: add support
for phy-supply").
This reverts commit 7911f409ff.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit ec107f04b6 ("rockchip: chromebook_minnie: Enable sound") and
commit 2d0c01b8f0 ("sound: rockchip: Add sound support for jerry")
enable audio support for chromebook_minnie and chromebook_jerry. Enable
it for chromebook_speedy as well, but put the non-upstream sound node
in the board -u-boot.dtsi instead.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The rk3288-veyron-speedy-u-boot.dtsi file duplicates the bootphase dts
fragments from rk3288-veyron-u-boot.dtsi even though it #inclues that.
Deduplicate these into the latter file, which should also make the eMMC
available to the other veyron boards' SPL.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Commit 9b312e26fc ("rockchip: Enable building a SPI ROM image on
jerry") produces a u-boot.rom file for chromebook_jerry, intended to be
written to SPI flash. Build this file for other veyron boards as well,
especially because they are already configured only to boot from SPI.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Boot devices defined in rk3308.c and in rk3308.dtsi do not match, causing
'same-as-spl' feature not to work. Update DTS definitions, aligning to
Linux kernel DTS and to other Rockchip DTS files, i.e. from dwmmc to mmc.
Add rk3308-rock-pi-s.dtb in dtb-y targets for CONFIG_ROCKCHIP_RK3308.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Some ROCK Pi S SKU/models are not equipped with SD-NAND (eMMC),
therefore SPL needs access to sdmmc: add it to rk3308-u-boot.dtsi
with bootph-all property.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Call to board_debug_uart_init() is useless, as mainline U-Boot can
not build TPL for rk3308, and proprietary ddr.bin to be used as TPL
is responsible to init debug uart. Moreover current implementation
of board_debug_uart_init() is not compatible with ROCK Pi S, as it
sets pins for UART2 channel 1 breaking access to sdmmc due to pinmux
conflict. Debug uart for ROCK Pi S is UART0.
Thus, avoid ROCKCHIP_RK3308 to select DEBUG_UART_BOARD_INIT and allow
to deselct it in rock-pi-s-rk3308_defconfig. The DEBUG_UART_BOARD_INIT
is already implied by ARCH_ROCKCHIP, therefore other boards based on
rk3308 chip are not affected by change.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Definition of function board_debug_uart_init() must be under
CONFIG_DEBUG_UART_BOARD_INIT and not under CONFIG_DEBUG_UART,
as it was: see debug_uart.h. In this way the debug uart can
be used but its board-specific initialization skipped by
configuration, if useless.
Signed-off-by: Massimo Pegorer <massimo.pegorer@vimar.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- Resync some of the K3 DTS files with the kernel, and pull in some
required related updates to keep drivers in sync with the dts files
now. Bring in some incremental fixes on top of one of the series I
applied recently as well as updating the iot2050 platform. Also do a
few small updates to the K2 platforms.
The following checks are more reasonable as the previous logs were a bit
misleading as we could still get the logs that the authetication is
being skipped but still authenticate. Move the debug prints and checks
to proper locations.
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Fix missing declaration of fdt_del_node_path() while compiling am625_fdt.c and
missing common_fdt.h include in common_fdt.c
Fixes: 70aa5a94d4 ("arm: mach-k3: am62: Fixup CPU core, gpu and pru nodes in fdt")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
This avoids having to maintain to defconfigs that are 99% equivalent.
The approach is to use binman to generate two flash images,
flash-pg1.bin and flash-pg2.bin. With the help of a template dtsi, we
can avoid duplicating the common binman image definitions.
Suggested-by: Andrew Davis <afd@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Update the am62 and am625 device-trees from linux v6.5-rc1. This needed
the following tweaks to the u-boot specific dtsi as well:
- Switch tick-timer to the main_timer as it's now defined in the main dtsi
- Secure proxies are defined in SoC dtsi
- Drop duplicate nodes - u-boot.dtsi is includes in r5-sk, no need for
either the definitions from main.dtsi OR duplication from u-boot.dtsi
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Reviewed-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Sjoerd Simons <sjoerd@collabora.com>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Timer0 is used by u-boot as the tick timer; Add it to the soc devices
list so it can be enabled via the k3 power controller.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Tested-by: Maxime Ripard <mripard@kernel.org>
Tested-by: Ravi Gunasekaran <r-gunasekaran@ti.com>
Tested-by: Mattijs Korpershoek <mkorpershoek@baylibre.com>
Cc: Francesco Dolcini <francesco@dolcini.it>
Cc: Wadim Egorov <w.egorov@phytec.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Hardkernel ODROID-M1 is a single board computer with a RK3568B2 SoC,
a slightly modified version of the RK3568 SoC.
Features tested on a ODROID-M1 8GB v1.0 2022-06-13:
- SD-card boot
- eMMC boot
- SPI Flash boot
- PCIe/NVMe/AHCI
- SATA port
- USB host
Device tree is imported from linux v6.4.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Stefan Agner <stefan@agner.ch>
Tested-by: Stefan Agner <stefan@agner.ch>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Update config, IO and memory regions used based on [1] with pcie3x2
config reg address and reg size corrected.
Before this change:
PCI Autoconfig: Bus Memory region: [0-3eefffff],
PCI Autoconfig: Bus I/O region: [3ef00000-3effffff],
After this change:
PCI Autoconfig: Bus Memory region: [40000000-7fffffff],
PCI Autoconfig: Bus I/O region: [f0100000-f01fffff],
[1] https://lore.kernel.org/lkml/20221112114125.1637543-2-aholmes@omnom.net/
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add missing pinctrl and defconfig options to enable PCIe and NVMe
support on Radxa ROCK 3 Model A.
Use of pcie20m1_pins and pcie30x2m1_pins ensure IO mux selection M1.
The following pcie_reset_h and pcie3x2_reset_h ensure GPIO func is
restored to the perstn pin, a workaround to avoid having to define
a new rockchip,pins.
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add board-specific devicetree/config for the RK3399T-based Radxa ROCK 4SE
board. This board offers similar peripherals in a similar form-factor to
the existing ROCK Pi 4B but uses the cost-optimised RK3399T processor
(which has different OPP table than the RK3399) and other minimal hardware
changes.
Kernel tag: next-20230719
Kernel commits:
- 86a0e14a82ea ("arm64: dts: rockchip: Add Radxa ROCK 4SE")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
To prepare for ROCK 4 SE support, changes are needed to the common ROCK
Pi 4 devicetree to move the OPP from the common devicetree to individual
board devicetrees. Sync the Rockchip RK3399 ROCK Pi 4-related DTs from
Linux to gain from these changes.
Kernel tag: next-20230719
Kernel commits:
cfa12c32b96f ("arm64: dts: rockchip: correct wifi interrupt flag in Rock \
Pi 4B")
cee572756aa2 ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK Pi 4")
2bd1d2dd808c ("arm64: dts: rockchip: Disable HS400 for eMMC on ROCK 4C+")
fd2762a62646 ("arm64: dts: rockchip: Move OPP table from ROCK Pi 4 dtsi")
Signed-off-by: Christopher Obbard <chris.obbard@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
For RK322x series ARM SoCs the OP-TEE is non-optional, as besides the TEE
it also provides the PSCI implementation, which is expected to be available
by upstream linux.
Select CONFIG_SPL_OPTEE_IMAGE if an FIT image is built.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
CONFIG_SPL_OPTEE_IMAGE option is used during DRAM size detection for
Rockchip ARM platform to indicate that an OP-TEE binary was already loaded
and a Trusted Execution Environment (TEE) is available in order to
block/reserve a memory-region for it.
This adds a bunch of new `#if's` to u-boot-rockchip.dtsi to include the
OP-TEE binary in the FIT image for ARM SOCs if CONFIG_SPL_OPTEE_IMAGE is
selected.
That makes it a little harder to read, but I opted for that, because all
the duplicates in an extra ARM-OP-TEE-specfic .dtsi would be the greater
evil, IMHO. Besides it's more likley being "forgotten" to sync when changes
in u-boot-rockchip.dtsi are made.
The no longer required rockchip-optee.dtsi and it's inclusions are dropped.
The hardcoded load address is common across all OP-TEE implemenations for
Rockchip (vendor and upstream).
The OP-TEE-binary is non-optional if CONFIG_SPL_OPTEE_IMAGE is selected and
there will be an error if the file does not exist and/or `TEE=` build
option is missing.
Signed-off-by: Alex Bee <knaerzche@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Current SYS_MALLOC_F_LEN of 0x2000 (8 KB) used in SPL is too small for
some RK3568 boards. SPL will print following during boot:
alloc space exhausted
Increase the default SYS_MALLOC_F_LEN to 0x20000 (128 KB) to mitigate.
Fixes: 2a950e3ba5 ("rockchip: Add rk3568 architecture core")
Signed-off-by: Jonas Karlman <jonas@kwiboo.se>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Long are gone the times TF-A couldn't handle the FDT passed by U-Boot.
Specifically, since commit e7b586987c0a ("rockchip: don't crash if we
get an FDT we can't parse") in TF-A, failure to parse the FDT will use
the fallback mechanism. This patch was merged in TF-A v2.4-rc0 from two
years ago.
New boards should likely have this option disabled or explicitly enable
it in their respective defconfig.
Because existing boards might depend on a TF-A version that predates
v2.4, let's just enable this option in all RK3399 defconfigs.
Maintainers of each board can decide for themselves if they would prefer
to disable this option and allow U-Boot to pass the DT to TF-A.
Cc: Quentin Schulz <foss+uboot@0leil.net>
Signed-off-by: Quentin Schulz <quentin.schulz@theobroma-systems.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
Add support for this SoM and IO board.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Neural Compute Module 6B(Neu6B) is a 96boards SoM-CB compute module
based on Rockchip RK3588J from Edgeble AI.
General features:
- Rockchip RK3588J
- up to 32GB LPDDR4x
- up to 128GB eMMC
- 2x MIPI CSI2 FPC
- On module WiFi6/BT
Neural Compute Module 6B(Neu6B) IO board is an industrial form factor
ready-to-use IO board from Edgeble AI.
General features:
- microSD slot
- 1x HDMI Out
- 1x HDMI In
- 2x DP
- 1x eDP
- 2x MIPI DSI connector
- 4x MIPI CSI2 connector
- 2x USB Host
- 2x USB 3.0 OTG/Host
- 1x SATA
- 1x 2.5Gbps Ethernet
- 1x M.2 B-Key for 4G/5G cards
- 1x M.2 M-Key slot
- 1x Onboard PoE
- 1x RS485, RS232, CAN
- 1x Audio, MIC port
- RTC battery slot
- 40-pin GPIO expansion
Neu6B needs to mount on top of this IO board in order to create a
complete Edgeble Neural Compute Module 6B(Neu6B) IO platform.
Kernel commits:
commit <5f06c3f508f7> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B SoM")
commit <3a9181a43b94> ("arm64: dts: rockchip: Add rk3588 Edgeble Neu6
Model B IO")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add rk3588j-u-boot.dtsi for adding U-Boot specific nodes and
properties for Rockchip RK3588J SoC.
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Rockchip RK3588J is the industrial-grade version of RK3588 SoC and
is operated with -40 °C to +85 °C temparature.
Add rk3588j specific dtsi for adding rk3588j specific operating points
and other changes to be add in future.
Kernel commit:
commit <8274a04ff1dc> ("arm64: dts: rockchip: Add Rockchip RK3588J")
Signed-off-by: Jagan Teki <jagan@edgeble.ai>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
