Only set the speed if it has changed from last time. Since the speed will
be 0 when the device is probed it will always be changed on the first
transfer after the device is probed.
Signed-off-by: Simon Glass <sjg@chromium.org>
The timeout value is never reset during the transfer. This means that when
transferring more data we eventually trigger the timeout.
This was reported on the mailing list:
"Spansion SPI flash read timeout with AM335x"
Signed-off-by: David Dueck <davidcdueck@googlemail.com>
CC: Tom Rini <trini@konsulko.com>
CC: Stefan Roese <sr@denx.de>
CC: Andy Pont <andy.pont@sdcsystems.com>
Tested-by: David Dueck <davidcdueck@googlemail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
These methods should be passed a slave device, not a bus. This matches the
old SPI interface. It is important to know which device is claiming the bus
so passing a bus is not that useful.
Reported-by: Haikun Wang <haikun.wang@freescale.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
Tested-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Removed the unnecessary error check from spi_xfer
as the bitlen zero is possible now to deassert the
chip select for which no data is required to be transfered.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Move the Freescale QSPI driver over to driver model.
Signed-off-by: Haikun Wang <Haikun.Wang@freescale.com>
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Tested-by: Peng Fan <Peng.Fan@freescale.com>
Acked-by: Simon Glass <sjg@chromium.org>
Convert this driver over to use driver model. Since all x86 platforms use
it, move x86 to use driver model for SPI and SPI flash. Adjust all dependent
code and remove the old x86 spi_init() function.
Note that this does not make full use of the new PCI uclass as yet. We still
scan the bus looking for the device. It should move to finding its details
in the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a convenience function to access the private data that a uclass stores
for each of its devices. Convert over most existing uses for consistency
and to provide an example for others.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add Lynxpoint to the driver so that the Asus Chromebox can be supported.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
By specification the FIFO size would be in a range 2-256 bytes. From TX Level
prospective it means we can set threshold in the range 0-(FIFO size - 1) bytes.
Hence there are currently two issues:
a) FIFO size 2 bytes is actually skipped since TX Level is 1 bit and could be
either 0 or 1 byte;
b) FIFO size is incorrectly decreased by 1 which already done by meaning of
TX Level register.
Fixes: 501943696e (spi: designware_spi: Fix detecting FIFO depth)
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Make local functions static and remove unneeded forward declarations.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Don't assume slave is always the first member of struct cf_spi_slave.
Use container_of instead of casting first structure member.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch enables QUAD read mode for qspi to improve the
read performace while loading the binaries from qspi.
Signed-off-by: Ravi Babu <ravibabu@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Don't assume slave is always the first member of struct ftssp010_spi.
Use to_ftssp010_spi() to ensure free correct address in spi_free_slave().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The third parameter of container_of is the name of the member within the struct.
Current code only works if the parameter passed to to_cf_qspi_slave named slave.
Fix it.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Expand the help messages for each driver. Add missing Kconfig for I2C,
SPI flash and thermal.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
The Quark SoC contains a legacy SPI controller in the legacy bridge
which is ICH7 compatible. Like Tunnel Creek and BayTrail, the BIOS
control register offset in the ICH SPI driver is wrong for the Quark
SoC too, unprotect_spi_flash() is added to enable the flash write.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
The base address is found in a different way and the protection bit is also
in a different place. Otherwise it is very similar.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
At present we go through various contortions to store the SPI slave's chip
select in its private data. This only exists when the slave is active so
must be set up when it is probed. Until the device is probed we don't
actually know what chip select it will appear on.
However, now that we can support per-child platform data, we can use that
instead. This allows us to set up the chip select when the child is bound,
and avoid the messy contortions.
Unfortunately this is a fairly large change and it seems to be difficult to
break it down further.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we use struct spi_slave as our device pointer in a lot of places
to avoid changing the old SPI API. At some point this will go away.
But for now, it is better if the SPI uclass sets up this pointer, rather
than relying on passing it into the device when it is probed. We can use the
new uclass child_pre_probe() method to do this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This is common to all SPI drivers and specifies a structure used by the
uclass. It makes more sense to define it in the uclass.
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
At present we try to use the 'reg' property and device tree aliases to give
devices a sequence number. The 'reg' property is often actually a memory
address, so the sequence numbers thus-obtained are not useful. It would be
better if the devices were just sequentially numbered in that case. In fact
neither I2C nor SPI use this feature, so drop it.
Some devices need us to look up an alias to number them within the uclass.
Add a flag to control this, so it is not done unless it is needed.
Adjust the tests to test this new behaviour.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Masahiro Yamada <yamada.m@jp.panasonic.com>
As a temporary measure before the ICH driver moves over to driver model,
add device tree support to the driver.
Signed-off-by: Simon Glass <sjg@chromium.org>
The QSPI controller in i.MX 6SoloX and Vybrid supports reading data using
IP register and AHB bus.
The original driver only supports reading data from IP interface. The IC
team suggests to use AHB read which is faster then IP read. Using AHB read,
we can directly memcpy, a "missed" access to the buffer will cause the
controller to clear the buffer and use the SEQID stored in bfgencr register
to initiate a read from flash device.
Since AHB bus is 64 bit width, we can not set MCR register using 32bit. In
order to minimize code change, redefine QSPI_MCR_END_CFD_LE to 64bit Little
endian but not 32bit Little endia.
Introduce a new configuration option CONFIG_SYS_FSL_QSPI_AHB. If want to
use AHB read, just define CONFIG_SYS_FSL_QSPI_AHB. If not, just ignore it.
Actually if Vybrid is migrated to use AHB read, this option can be removed and
IP read function can be discared. The reason to introduce this option
is that only i.MX SOC is tested in my side, no Vybrid platform for me.
In spi_setup_slave, the original piece code to set AHB is deleted, since
Vybrid platform does not use this to intiate AHB read. Instead, add
qspi_init_ahb_read function if defined CONFIG_SYS_FSL_QSPI_AHB.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
No functional change, just simplify the code a bit.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
fdt_first_subnode() returns -FDT_ERR_NOTFOUND if no subnode found.
0 is supposed to be a valid offset returns from fdt_first_subnode().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
To support bigger than 16MB size qspi flashes, spi framework uses bank
switch to access higher bank or lower bank.
In this patch, QSPI_CMD_BRRD, QSPI_CMD_BRWR, QSPI_CMD_WREAR, QSPI_CMD_RDEAR
is initialized in LUT register with related pad and length configuration.
qspi_op_pp is originally for page programming, this patch reuses this function
for bank register switch and renamed it with qspi_op_write.
Since bank or EAR register is only 1 byte length, however original qspi_op_pp
or now renamed qspi_op_write only support 4 bytes lenght as the access unit,
this will trigger data abort exception when access EAR or bank register.
This is because upper framework passes a 1 bytes pointer to qspi_op_write,
however qspi_op_write treat it as an int pointer. This patch fixes this for
accessing EAR or bank register.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Linux now also contains SPI driver, yet the name is 'snps,dw-apb-ssi'.
Fix the naming before we have to support both names.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <clsee@opensource.altera.com>
Cc: Dinh Nguyen <dinguyen@opensource.altera.com>
Cc: Pavel Machek <pavel@denx.de>
Cc: Stefan Roese <sr@denx.de>
Cc: Vince Bridgers <vbridger@opensource.altera.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Current code tries to find the highest valid fifo depth by checking the value
it wrote to DW_SPI_TXFLTR. There are a few problems in current code:
1) There is an off-by-one in dws->fifo_len setting because it assumes the latest
register write fails so the latest valid value should be fifo - 1.
2) We know the depth could be from 2 to 256 from HW spec, so it is not necessary
to test fifo == 257. In the case fifo is 257, it means the latest valid
setting is fifo = 256. So after the for loop iteration, we should check
fifo == 2 case instead of fifo == 257 if detecting the FIFO depth fails.
This patch fixes above issues.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add 4k erase command support for qspi driver. reuse the 64k erase function,
but change the function name from qspi_op_se to qspi_op_erase, since it
supports 64k and 4k erase.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
According cs, use different amba_base to choose the corresponding
flash devices. If not, `sf probe 1:0` and `sf probe 1:1` will
choose the same flash device, but not different flash devices.
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Use QSPI_CMD_xx instead of flash opcodes
Signed-off-by: Peng Fan <Peng.Fan@freescale.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
Add Intel Tunnel Creek SPI controller support which is an ICH7
compatible device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
ICH 7 SPI controller only supports byte program (02h) for SST flash.
Word program (ADh) is not supported.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
ICH 7 SPI controller only supports array read command (03h).
Fast array read command (0Bh) is not supported.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
The ich spi controller driver spi_xfer() tries to align reading
address to 64 bytes when doing spi data in, which causes a bug of
either infinite loop or a huge size memcpy().
Actually the ich spi controller does not have such requirement of
64 bytes alignment when reading data from spi slave devices.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
As suggested by Pavel, here some fixes to the designware SPI driver:
- Spelling fixes
- Comment for timeout added
- Removed n_bytes completely (bits_per_word is enough for this)
- Unput clock now not defined via macro. The function to
get the clock value is now called directly from within the driver
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This patch adds the driver for the Designware master SPI controller. This
IP core is integrated on the Altera SoCFPGA. This implementation is a
driver model (DM) implementation. So multiple SPI drivers can be used.
Thats necessary, since SoCFPGA also integrates the Cadence QSPI controller
used to connect the SPI NOR flashes. Without DM, using multiple SPI
drivers is not possible.
This driver is very loosely based on the Linux driver. Most of the Linux
driver is removed. Only the polling loop for the transfer is really used
from this driver, as we don't support interrupts and DMA right now.
This is tested on the SoCrates SoCFPGA board using the SPI pins on the
P14 header.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
This driver is cloned from the Altera Rockerboard.org U-Boot
repository. I used this git tag: ACDS14.0.1_REL_GSRD_RC2. With Some
modification to support the U-Boot driver model (DM).
As mentioned above, in this new version I ported this driver to the
new driver model (DM). One big advantage of this move is that now
multiple SPI drivers can be enabled on one platform. And since the
SoCFPGA also has the Designware SPI master controller integrated,
this feature is really needed to support both controllers.
Because of this, this series needs the DT support for SoCFPGA
to be applied. For DT based probing in the SPI DM.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chin Liang See <clsee@altera.com>
Cc: Dinh Nguyen <dinguyen@altera.com>
Cc: Vince Bridgers <vbridger@altera.com>
Cc: Marek Vasut <marex@denx.de>
Cc: Pavel Machek <pavel@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
just add a few ifdefs around because this
device is very similar to dra7xxx.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
