Commit graph

1516 commits

Author SHA1 Message Date
Wolfgang Denk
c8a3b109f0 Cleanup out-or-tree building for some boards (.depend)
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:49:18 +02:00
Wolfgang Denk
a30cc5a340 Cleanup: fix out-of-tree building for some boards
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:38:50 +02:00
Wolfgang Denk
461fa68d20 Cleanup: replace hard-wired $(AR) 'crv' settings by $(ARFLAGS)
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-07-02 23:00:14 +02:00
Esben Haabendal
ee4ae38342 mpc8260: add fdt_fixup_ethernet support
Add support for updating mac-address and local-mac-address in fdt for
all MPC8260 targets.

Signed-off-by: Esben Haabendal <eha@doredevelopment.dk>
2008-07-01 23:44:22 +02:00
Juergen Kilb
d92ea21baf i.MX31: fixed CTRL-C detection
The Register URXD contains status information in bits [15..8].
With status bit 15 set, CTRL-C was reported as 0x8003 instead
of 0x03. Therefore CTRL-C was not detected.
To solve this, bits [15..8] were masked out now.

Signed-off-by: Juergen Kilb <J.Kilb@gmx.de>
Acked-by: Felix Radensky <felix@embedded-sol.com>
2008-07-01 20:54:04 +02:00
Wolfgang Denk
e093a24762 Coding Style Cleanup
Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-06-28 23:34:37 +02:00
Haavard Skinnemoen
341188b9cc MMC: Consolidate MMC/SD command definitions
This moves the MMC and SD Card command definitions from
include/asm/arch/mmc.h into include/mmc.h. These definitions are
given by the MMC and SD Card standards, not by any particular
architecture.

There's a lot more room for consolidation in the MMC drivers which
I'm hoping to get done eventually, but this patch is a start.

Compile-tested for all avr32 boards as well as lpc2292sodimm and
lubbock. This should cover all three mmc drivers in the tree.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-06-28 22:40:15 +02:00
Anatolij Gustschin
96026d42fa Fix 4xx build issue
Building for 4xx doesn't work since commit 4dbdb768:

In file included from 4xx_pcie.c:28:
include/asm/processor.h:971: error: expected ')' before 'ver'
make[1]: *** [4xx_pcie.o] Error 1

This patch fixes the problem.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-19 22:48:45 +02:00
Becky Bruce
9973e3c614 Change initdram() return type to phys_size_t
This patch changes the return type of initdram() from long int to phys_size_t.
This is required for a couple of reasons: long int limits the amount of dram
to 2GB, and u-boot in general is moving over to phys_size_t to represent the
size of physical memory.  phys_size_t is defined as an unsigned long on almost
all current platforms.

This patch *only* changes the return type of the initdram function (in
include/common.h, as well as in each board's implementation of initdram).  It
does not actually modify the code inside the function on any of the platforms;
platforms which wish to support more than 2GB of DRAM will need to modify
their initdram() function code.

Build tested with MAKEALL for ppc, arm, mips, mips-el. Booted on powerpc
MPC8641HPCN.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-12 08:50:18 +02:00
Wolfgang Denk
1a5017601f Merge branch 'master' of git://www.denx.de/git/u-boot-mips 2008-06-11 22:48:09 +02:00
Wolfgang Denk
cdeb62e20d Merge branch 'master' of git://www.denx.de/git/u-boot-fdt 2008-06-11 22:30:47 +02:00
Wolfgang Denk
1730edf76c Merge branch 'master' of git://www.denx.de/git/u-boot-ppc4xx 2008-06-11 22:13:07 +02:00
Wolfgang Denk
5ea67393b8 Merge branch 'master' of git://www.denx.de/git/u-boot-mpc85xx
Conflicts:

	include/asm-ppc/fsl_lbc.h

Signed-off-by: Wolfgang Denk <wd@denx.de>
2008-06-11 21:33:16 +02:00
Kumar Gala
859a86a25c 85xx/86xx: Move to dynamic mgmt of LAWs
With the new LAW interface (set_next_law) we can move to letting the
system allocate which LAWs are used for what purpose.  This makes life
a bit easier going forward with the new DDR code.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Acked-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-11 01:52:23 -05:00
Kumar Gala
f060054dad FSL LAW: Keep track of LAW allocations
Make it so we keep track of which LAWs have allocated and provide
a function (set_next_law) which can allocate a LAW for us if one is
free.

In the future we will move to doing more "dynamic" LAW allocation
since the majority of users dont really care about what LAW number
they are at.

Also, add CONFIG_MPC8540 or CONFIG_MPC8560 to those boards which needed them

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2008-06-11 01:50:53 -05:00
Sergei Poselenov
740280e68c Added the upmconfig() function for 85xx.
Signed-off-by: Sergei Poselenov <sposelenov@emcraft.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2008-06-11 00:29:29 -05:00
Wolfgang Grandegger
6beecfbb54 MPC85xx: Beautify boot output of L2 cache configuration
The boot output is now aligned poperly with other boot output
lines, e.g.:

  FLASH: 128 MB
  L2:    512 KB enabled

Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
2008-06-10 18:22:26 -05:00
Kumar Gala
730b2fcf6f 85xx: Add setting of cache props in the device tree.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 18:22:25 -05:00
Kumar Gala
4dbdb7681e 85xx: expose cpu identification
The current cpu identification code is used just to return the name
of the processor at boot.  There are some other locations that the name
is useful (device tree setup).  Expose the functionality to other bits
of code.

Also, drop the 'E' suffix and add it on by looking at the SVR version
when we print this out.  This is mainly to allow the most flexible use
of the name.  The device tree code tends to not care about the 'E' suffix.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-10 18:22:25 -05:00
Gerald Van Baren
fec6d9ee7c Remove the deprecated CONFIG_OF_FLAT_TREE
Use CONFIG_OF_LIBFDT instead to support flattened device trees.  It is
cleaner, has better functionality, and is better supported.

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2008-06-09 21:13:35 -04:00
Gerald Van Baren
589c04271d Convert mpc7448hpc2 to CONFIG_OF_LIBFDT
This was configured to use the deprecated CONFIG_OF_FLAT_TREE, change
to CONFIG_OF_LIBFDT.

WARNING: This conversion is untested because I do not have a board to
test it on.

NOTE: The FDT blob (DTS) must have an /aliases/ethernet0 and (optionally)
/aliases/ethernet1 property for the ethernet to work.

Signed-off-by: Gerald Van Baren <vanbaren@cideas.com>
2008-06-09 21:13:24 -04:00
Kumar Gala
ee1e35bede 85xx: Only use PORPLLSR[DDR_Ratio] on platforms that define it
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-06-09 13:31:20 -05:00
Becky Bruce
3b9519fc50 MPC85xx: Change traps.c to not reference non-addressable memory
Currently, END_OF_RAM is used by the trap code to determine if
we should attempt to access the stack pointer or not. However,
on systems with a lot of RAM, only a subset of the RAM is
guaranteed to be mapped in and accessible.  Change END_OF_RAM
to use get_effective_memsize() instead of using the raw ram
size out of the bd.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-09 13:31:20 -05:00
Shinya Kuribayashi
79b51ff820 [MIPS] cpu/mips/Makefile: Split [CS]OBJS onto separate lines
Also get rid of some #ifdefs in *.c files.

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-06-07 20:51:59 +09:00
Shinya Kuribayashi
8bde63eb3f [MIPS] Rename Alchemy processor configs into CONFIG_SOC_*
CONFIG_SOC_AU1X00

  Common Alchemy Au1x00 stuff. All Alchemy processor based machines
  need to have this config as a system type specifier.

CONFIG_SOC_AU1000, CONFIG_SOC_AU1100, CONFIG_SOC_AU1200,
CONFIG_SOC_AU1500, CONFIG_SOC_AU1550

  Machine type specifiers. Each port should have one of aboves.

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-06-07 20:51:56 +09:00
Becky Bruce
279726bd00 MPC86xx: Change traps.c to not reference non-addressable memory
Currently, END_OF_RAM is used by the trap code to determine if
we should attempt to access the stack pointer or not. However,
on systems with a lot of RAM, only a subset of the RAM is
guaranteed to be mapped in and accessible.  Change END_OF_RAM
to use get_effective_memsize() instead of using the raw ram
size out of the bd to prevent us from trying to access
non-mapped memory.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-06 10:55:35 -05:00
Stefan Roese
b2815f7928 ppc4xx: Fix misspelled CONFIG_440SPE/440EPX/GRX config options
We use upper case letters for the AMCC processor defines (like
CONFIG_440SPE) in U-Boot. So the 440SPe is labeled CONFIG_440SPE and
not CONFIG_440SPe. This patch fixes the last misspelled config options.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-06 16:10:41 +02:00
Shinya Kuribayashi
7daf2ebe91 [MIPS] Update <asm/addrspace.h> header
- Fix traditional KSEG names
- Replace PHYSADDR with CPHYSADDR

Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-06-05 22:29:00 +09:00
Shinya Kuribayashi
5f64d21c9a [MIPS] Kill unused <version.h> inclusions
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-06-05 22:29:00 +09:00
Grant Erickson
22f371b630 PPC4xx: Simplified post_word_{load, store}
This patch simplifies post_word_{load,store} by using the preprocessor
to eliminate redundant, copy-and-pasted code.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
2008-06-03 21:22:26 +02:00
Hans-Christian Egtvedt
60445cb5c3 atmel_spi: Driver for the Atmel SPI controller
This adds a driver for the SPI controller found on most AT91 and AVR32
chips, implementing the new SPI API.

Changed in v4:
  - Update to new API
  - Handle zero-length transfers appropriately. The user may send a
    zero-length SPI transfer with SPI_XFER_END set in order to
    deactivate the chip select after a series of transfers with chip
    select active. This is useful e.g. when polling the status
    register of DataFlash.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
2008-06-03 20:30:05 +02:00
Haavard Skinnemoen
d255bb0e78 SPI API improvements
This patch gets rid of the spi_chipsel table and adds a handful of new
functions that makes the SPI layer cleaner and more flexible.

Instead of the spi_chipsel table, each board that wants to use SPI
gets to implement three hooks:
  * spi_cs_activate(): Activates the chipselect for a given slave
  * spi_cs_deactivate(): Deactivates the chipselect for a given slave
  * spi_cs_is_valid(): Determines if the given bus/chipselect
    combination can be activated.

Not all drivers may need those extra functions however. If that's the
case, the board code may just leave them out (assuming they know what
the driver needs) or rely on the linker to strip them out (assuming
--gc-sections is being used.)

To set up communication parameters for a given slave, the driver needs
to call spi_setup_slave(). This returns a pointer to an opaque
spi_slave struct which must be passed as a parameter to subsequent SPI
calls. This struct can be freed by calling spi_free_slave(), but most
driver probably don't want to do this.

Before starting one or more SPI transfers, the driver must call
spi_claim_bus() to gain exclusive access to the SPI bus and initialize
the hardware. When all transfers are done, the driver must call
spi_release_bus() to make the bus available to others, and possibly
shut down the SPI controller hardware.

spi_xfer() behaves mostly the same as before, but it now takes a
spi_slave parameter instead of a spi_chipsel function pointer. It also
got a new parameter, flags, which is used to specify chip select
behaviour. This may be extended with other flags in the future.

This patch has been build-tested on all powerpc and arm boards
involved. I have not tested NIOS since I don't have a toolchain for it
installed, so I expect some breakage there even though I've tried
fixing up everything I could find by visual inspection.

I have run-time tested this on AVR32 ATNGW100 using the atmel_spi and
DataFlash drivers posted as a follow-up. I'd like some help testing
other boards that use the existing SPI API.

But most of all, I'd like some comments on the new API. Is this stuff
usable for everyone? If not, why?

Changed in v4:
  - Build fixes for various boards, drivers and commands
  - Provide common struct spi_slave definition that can be extended by
    drivers
  - Pass a struct spi_slave * to spi_cs_activate and spi_cs_deactivate
  - Make default bus and mode build-time configurable
  - Override default SPI bus ID and mode on mx32ads and imx31_litekit.

Changed in v3:
  - Add opaque struct spi_slave for controller-specific data associated
    with a slave.
  - Add spi_claim_bus() and spi_release_bus()
  - Add spi_free_slave()
  - spi_setup() is now called spi_setup_slave() and returns a
    struct spi_slave
  - soft_spi now supports four SPI modes (CPOL|CPHA)
  - Add bus parameter to spi_setup_slave()
  - Convert the new i.MX32 SPI driver
  - Convert the new MC13783 RTC driver

Changed in v2:
  - Convert the mpc8xxx_spi driver and the mpc8349emds board to the
    new API.

Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Tested-by: Guennadi Liakhovetski <lg@denx.de>
2008-06-03 20:28:50 +02:00
Stefan Roese
bbeff30cbd ppc4xx: Remove superfluous dram_init() call or replace it by initdram()
Historically the 405 U-Boot port had a dram_init() call in early init
stage. This function was still called from start.S and most of the time
coded in assembler. This is not needed anymore (since a long time) and
boards should implement the common initdram() function in C instead.

This patch now removed the dram_init() call from start.S and removes the
empty implementations that are scattered through most of the 405 board
ports. Some older board ports really implement this dram_init() though.
These are:

csb272
csb472
ERIC
EXBITGEN
W7OLMC
W7OLMG

I changed those boards to call this assembler dram_init() function now
from their board specific initdram() instead. This *should* work, but please
test again on those platforms. And it is perhaps a good idea that those
boards use some common 405 SDRAM initialization code from cpu/ppc4xx at
some time. So further patches welcome here.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:19 +02:00
Stefan Roese
192f90e272 ppc4xx: Use new 4xx SDRAM controller enable defines in common ECC code
Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:13 +02:00
Stefan Roese
39b32be18c ppc4xx: Fix common ECC generation code for 440GP style platforms
This patch makes the common 4xx ECC code really usable on 440GP style
platforms.

Since the IBM DDR controller used on 440GP/GX/EP/GR is not register
compatible to the IBM DDR/2 controller used on 405EX/440SP/SPe/460EX/GT
we need to make some processor dependant defines used later on by the
driver.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:08 +02:00
Stefan Roese
ec724f883e ppc4xx: Change Kilauea to use the common DDR2 init function
This patch changes the kilauea and kilauea_nand (for NAND booting)
board port to not use a board specific DDR2 init routine anymore. Now
the common code from cpu/ppc4xx is used.

Thanks to Grant Erickson for all his basic work on this 405EX early
bootup.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:22:03 +02:00
Stefan Roese
36ea16f6a0 ppc4xx: Consolidate PPC4xx SDRAM/DDR/DDR2 defines, part1
This patch removes all SDRAM related defines from the PPC4xx headers
ppc405.h and ppc440.h. This is needed since now some 405 PPC's use
the same SDRAM controller as 440 systems do (like 405EX and 440SP).

It also introduces new defines for the equipped SDRAM controller based on
which PPC variant is used. There new defines are:

used on 405GR/CR/EP and some Xilinx Virtex boards.

used on 440GP/GX/EP/GR.

used on 440EPx/GRx.

used on 405EX/r/440SP/SPe/460EX/GT.

Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:21:53 +02:00
Stefan Roese
64852d09e0 ppc4xx/NAND_SPL: Consolidate 405 and 440 NAND booting code in start.S
This patch consolidates the 405 and 440 parts of the NAND booting code
selected via CONFIG_NAND_SPL. Now common code is used to initialize the
SDRAM by calling initdram() and to "copy/relocate" to SDRAM/OCM/etc.
Only *after* running from this location, nand_boot() is called.

Please note that the initsdram() call is now moved from nand_boot.c
to start.S. I experienced problems with some boards like Kilauea
(405EX), which don't have internal SRAM (OCM) and relocation needs to
be done to SDRAM before the NAND controller can get accessed. When
initdram() is called later on in nand_boot(), this can lead to problems
with variables in the bss sections like nand_ecc_pos[].

Signed-off-by: Stefan Roese <sr@denx.de>
Acked-by: Scott Wood <scottwood@freescale.com>
2008-06-03 20:21:49 +02:00
Grant Erickson
c821b5f120 ppc4xx: Enable Primordial Stack for 40x and Unify ECC Handling
This patch (Part 1 of 2):

* Rolls up a suite of changes to enable correct primordial stack and
  global data handling when the data cache is used for such a purpose
  for PPC40x-variants (i.e. CFG_INIT_DCACHE_CS).

* Related to the first, unifies DDR2 SDRAM and ECC initialization by
  eliminating redundant ECC initialization implementations and moving
  redundant SDRAM initialization out of board code into shared 4xx
  code.

* Enables MCSR visibility on the 405EX(r).

* Enables the use of the data cache for initial RAM on
  both AMCC's Kilauea and Makalu and removes a redundant
  CFG_POST_MEMORY flag from each board's CONFIG_POST value.

  - Removed, per Stefan Roese's request, defunct memory.c file for
    Makalu and rolled sdram_init from it into makalu.c.

With respect to the 4xx DDR initialization and ECC unification, there
is certainly more work that can and should be done (file renaming,
etc.). However, that can be handled at a later date on a second or
third pass. As it stands, this patch moves things forward in an
incremental yet positive way for those platforms that utilize this
code and the features associated with it.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
Signed-off-by: Stefan Roese <sr@denx.de>
2008-06-03 20:20:50 +02:00
Grant Erickson
a439680019 PPC4xx: Simplified post_word_{load, store}
This patch simplifies post_word_{load,store} by using the preprocessor
to eliminate redundant, copy-and-pasted code.

Signed-off-by: Grant Erickson <gerickson@nuovations.com>
2008-06-03 20:20:01 +02:00
Becky Bruce
9b124a6834 MPC512x: Change traps.c to not reference non-addressable memory
Currently, END_OF_RAM is used by the trap code to determine if
we should attempt to access the stack pointer or not. However,
on systems with a lot of RAM, only a subset of the RAM is
guaranteed to be mapped in and accessible.  Change END_OF_RAM
to use get_effective_memsize() instead of using the raw ram
size out of the bd.

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03 19:47:14 +02:00
Becky Bruce
e34a0e911b PPC: 86xx Add bat registers to reginfo command
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03 18:05:15 +02:00
Becky Bruce
31d8267224 PPC: Create and use CONFIG_HIGH_BATS
Change all code that conditionally operates on high bat
registers (that is, BATs 4-7) to look at CONFIG_HIGH_BATS
instead of the myriad ways this is done now.  Define the option
for every config for which high bats are supported (and
enabled by early boot, on parts where they're not always
enabled)

Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
2008-06-03 17:48:41 +02:00
Wolfgang Denk
912810eeca Merge remote branch 'u-boot-at91/for-1.3.4' 2008-06-03 00:24:36 +02:00
Wolfgang Denk
7a68389a23 Merge remote branch 'u-boot-avr32/master' 2008-06-03 00:19:57 +02:00
Shinya Kuribayashi
e2ad842662 [MIPS] <asm/mipsregs.h>: Update coprocessor register access macros
Signed-off-by: Shinya Kuribayashi <skuribay@ruby.dti.ne.jp>
2008-05-30 00:53:38 +09:00
Haavard Skinnemoen
a8092c021d avr32: Fix theoretical race in udelay()
If the specified delay is very short, the cycle counter may go past the
"end" time we are waiting for before we get around to reading it.

Fix it by checking the different between the cycle count "now" and the
cycle count at the beginning. This will work as long as the delay
measured in number of cycles is below 2^31.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:31 +02:00
Haavard Skinnemoen
48ea623eae avr32: Compile atmel_mci.o conditionally
Remove #ifdef CONFIG_MMC from the source file and use conditional
compilation in the Makefile instead.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:31 +02:00
Haavard Skinnemoen
e92a5bf833 avr32: Fix wrong error flags in atmel_mci driver
Make sure we check for CRC errors when sending commands that use CRC
checking.

Reported-by: Gururaja Hebbar K R <gururajakr@sanyo.co.in>
Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:31 +02:00
Haavard Skinnemoen
7a96ddadd1 avr32: Fix two warnings in atmel_mci.c
The warnings are harmless but annoying. Let's fix them.

Signed-off-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com>
2008-05-27 15:27:31 +02:00