The gpio command currently uses equal bank names "GPIO0_"
for all existing gpio banks, i. e.:
U-Boot# gpio status -a
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: output: 1 [x] dbg1.gpios
...
Bank GPIO0_:
GPIO0_0: input: 0 [ ]
GPIO0_1: input: 0 [ ]
...
So the command is broken, it is not possible to address
a desired bank. Add gpio aliases to fix this.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
New imx8 boards started adding duplicated UART init code.
Factor out this to common function sc_pm_setup_uart().
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This file setups UART5 based serial to be used as pre-relocation
console in the U-Boot proper.
On purpose pinux configuration is omitted here as it has been already
done in SPL. For early pre-relocation code we only need the serial
device from DTS.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
This commit ports from Linux kernel - tag: v5.1 - the device tree
description for display5 board.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Those properties are U-Boot specific as the mxs gpio Linux driver (up to
version v5.1.11) is not supporting them.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This patch copies from the Linux kernel stable (tag v5.1.11)
SHA1: 17bb763e7eaf i.MX28 related device tree files.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Currently, when the spl_boot_device checks the boot device, it
will only return MMC1 when it's either sd or eMMC regardless
of whether or not it's MMC1 or MMC2. This is a problem when
booting from MMC2 if MMC isn't being manually configured like in
the DM_SPL case with SPL_OF_CONTROL.
This patch will check the register and return either MMC1 or MMC2.
Signed-off-by: Adam Ford <aford173@gmail.com>
Writing/updating boot image in nand device is not
straight forward in i.MX6 platform and it requires
boot control block(BCB) to be configured.
It becomes difficult to use uboot 'nand' command to
write BCB since it requires platform specific attributes
need to be taken care of.
It is even difficult to use existing msx-nand.c driver by
incorporating BCB attributes like mxs_dma_desc does
because it requires change in mtd and nand command.
So, cmd_nandbcb implemented in arch/arm/mach-imx
BCB contains two data structures, Firmware Configuration Block(FCB)
and Discovered Bad Block Table(DBBT). FCB has nand timings,
DBBT search area, page address of firmware.
On summary, nandbcb update will
- erase the entire partition
- create BCB by creating 2 FCB/DBBT block followed by
1 FW block based on partition size and erasesize.
- fill FCB/DBBT structures
- write FW/SPL on FW1
- write FCB/DBBT in first 2 blocks
for nand boot, up on reset bootrom look for FCB structure in
first block's if FCB found the nand timings are loaded for
further reads. once FCB read done, DTTB will load and finally
firmware will be loaded which is boot image.
Refer section "NAND Boot" from doc/imx/common/imx6.txt for more usage
information.
Reviewed-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: Sergey Kubushyn <ksi@koi8.net>
Signed-off-by: Shyam Saini <shyam.saini@amarulasolutions.com>
Add code to print the channel stride, this would help to
print the stride of associated channel.
Here is sample print on LPDDR4, 50MHz.
256B stride
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram ddr info print support, this would help to
observe the sdram base parameters.
Here is sample print on LPDDR4, 50MHz channel 0
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add sdram driver to handle debug across rockchip SoCs.
This would help to improve code debugging feature for
sdram drivers in rockchip family, whoever wants to
debug the driver should call these core debug code on
their respective platform sdram drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Add DDR4 enum number in common header.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
dramtype enum numbers as common across all dram controllers
in rockchip, so move the eneum values in common header.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Move common sdram structures like sdram_cap_info, sdram_base_params
into sdram_common header, this would help to reuse the same
from another controllers like px30.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Most of the ddr parameters are common in rk3399_base_params
structure and which would reuse it in another controller like
px30 in future.
So, rename the structure from rk3399_base_params into
sdram_base_params.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Signed-off-by: YouMin Chen <cym@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Group common ddr attributes like
- rank
- col
- bk
- bw
- dbw
- row_3_4
- cs0_row
- cs1_row
- ddrconfig
into a common cap_info structure for more code readability and extend
if possible based on the new features.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
Let the board continue boot from the storage device where
it bootup.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <Kever.yang@rock-chips.com>
RK3399 use sdhci for eMMC and DW MMC for SD Card, and
spl will only try to boot from SDMMC if we don't specify
other boot device for spl-boot-order. So add sdhci and sdmmc
for spl-boot-order here.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the dts files for the Rock960 boards from Linux to get the
latest changes and fixes for the devices.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
- Various FS/disk related fixes with security implications.
- Proper fix for the pci_ep test.
- Assorted bugfixes
- Some MediaTek updates.
- 'env erase' support.
The timer0 node has its two clocks written in reversed order. The timer0
is used as the tick timer which causes a problem that the time a delay
function used is 4 times longer.
This patch reverses these two clocks to solve this issue.
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
This patch sets CNTVOFF of ARM CP15 timer to zero to make sure the virtual
counter is fully usable for linux kernel.
Cc: Albert Aribaud <albert.u.boot@aribaud.net>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
If U-Boot is loaded and started from TF-A (you need to change
SYS_TEXT_BASE to 0x60000000), it will hang up at flash initialization.
If secure mode is off (default, or -machine virt,secure=off) at qemu,
it will provide dtb with two flash memory banks:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x0 0x0 0x4000000 0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
If secure mode is on, on the other hand, qemu provides dtb with 1 bank:
flash@0 {
bank-width = <0x4>;
reg = <0x0 0x4000000 0x0 0x4000000>;
compatible = "cfi-flash";
};
As a result, flash_init()/flash_get_size() will eventually fail.
With this patch applied, relevant CONFIG values are modified.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Tested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently, CONFIG_TFABOOT is located in armv8/fsl-layerscape Kconfig,
but it will be also useful for other targets if some additional
configuration are necessary.
So move it to arch/arm/Kconfig.
Please note that CONFIG_TFABOOT still depends on
CONFIG_ARCH_SUPPORT_TFABOOT and so the menu won't come up
if any target doesn't need its own customization for TF-A boot.
This will maintain the compatibility.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Rajesh Bhagat <rajesh.bhagat@nxp.com>
Cc: York Sun <york.sun@nxp.com>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Cc: Priyanka Jain <priyanka.jain@nxp.com>
Cc: Sriram Dash <sriram.dash@nxp.com>
Cc: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Cc: Peng Ma <peng.ma@nxp.com>
Cc: Yuantian Tang <andy.tang@nxp.com>
Cc: Pankit Garg <pankit.garg@nxp.com>
When a crash occurs in thumb mode the crash dump is incorrect. This is due
to the usage of a non-existing configuration variable CONFIG_ARM_THUMB in
the definition of macro thumb_mode(regs).
Use CONFIG_IS_ENABLED(SYS_THUMB_BUILD) to detect that the code has been
compiled for thumb mode. Remove ARM_THUMB from config_whitelist.txt.
With the patch crash dumps indicate thumb mode correctly.
On a system with thumb mode:
=> exception unaligned
data abort
pc : [<8f7a2b52>] lr : [<8f7ab1ef>]
reloc pc : [<1780cb52>] lr : [<178151ef>]
sp : 8ed8c3f8 ip : 8f7a2b4d fp : 00000002
r10: 8f7f8228 r9 : 8ed95ea8 r8 : 8ed99488
r7 : 8f7ab141 r6 : 00000000 r5 : 8ed8c3f9 r4 : 8f7f6390
r3 : 8ed9948c r2 : 00000001 r1 : 00000000 r0 : 8f7f6390
Flags: nzCv IRQs off FIQs off Mode SVC_32 (T)
Code: 8f7e 466d f105 0501 (e9d5) 6700
The Flags line has '(T)' and in the Code line the output is in u16 groups.
On a system without thumb mode:
=> exception breakpoint
prefetch abort
pc : [<7ff5a5c8>] lr : [<7ff675ec>]
reloc pc : [<0000e5c8>] lr : [<0001b5ec>]
sp : 7ee0ad80 ip : 7ff5a5cc fp : 7ff674cc
r10: 00000002 r9 : 7ef0bed8 r8 : 7ffd6214
r7 : 7ef0e080 r6 : 00000000 r5 : 7ffd4090 r4 : 00000000
r3 : 7ef0e084 r2 : 00000001 r1 : 00000000 r0 : 7ffd4090
Flags: nzCv IRQs off FIQs off Mode SVC_32
Code: e1a0500d e2855001 e1c560d0 e3a00001 (e12fff1e)
The Flags line does not show '(T)' and in the Code line the output is in
u32 groups.
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The TI AM654x EVM base board and the associated daughtercards have on-
board I2C-based EEPROMs containing board configuration data. Use the
board detection infrastructure introduced earlier to do the following:
1) Parse the AM654x EVM base board EEPROM and populate items like board
name and MAC addresses into the TI common EEPROM data structure
residing in SRAM scratch space
2) Check for presence of daughter card(s) by probing the associated
presence signals via an I2C-based GPIO expander. Then, if such a
card is found, parse the data such as additional Ethernet MAC
addresses from its on-board EEPROM and populate into U-Boot
accordingly
3) Dynamically create an U-Boot ENV variable called overlay_files
containing a list of daugherboard-specific DTB overlays based on
daughercards found.
This patch adds support for the AM654x base board ("AM6-COMPROCEVM")
as well as for the IDK ("AM6-IDKAPPEVM"), OLDI LCD ("OLDI-LCD1EVM")
PCIe/USB3.0 ("SER-PCIEUSBEVM"), 2 Lane PCIe/USB2.0 ("SER-PCIE2LEVM"),
and general purpuse ("AM6-GPAPPEVM") daughtercards.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The board detection scheme employed on various TI EVMs makes use of
SRAM scratch space to share data read from an on-board EEPROM between
the different bootloading stages. Map the associated definition that's
used to locate this data into the SRAM scratch space we use on AM654x.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
The AM654 base board has a TCA9554/PCA9554-type GPIO expander on the
wkup_i2c0 bus at address 0x38 that is used to detect the presence of
daughter cards. Add a respective DTS description of this expander
to enable its use.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
To enable the use of an EEPROM-based board detection scheme we need to
be able to access the I2C bus associated with the EEPROMs across all
3 stages of U-Boot: R5 SPL, A53 SPL, and A53 U-Boot (proper). So go
ahead and add/update the wkup_i2c0 peripheral module DTS definitions
and its associated pinmux node accordingly.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Only U-Boot specifc DT properties or overrides, must be in -u-boot.dtsi.
Pinctrl nodes does not belong here. Now that pinctrl nodes are in kernel
DT, there is no reason to be keep these in -u-boot.dtsi. Move them to
proper places so that it would ease copying DT entries from kernel DT.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
There is no need for to include this header here, so drop it.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Use the System Firmware (SYSFW) loader framework to load and start
the SYSFW as part of the AM654 early initialization sequence. While
at it also initialize the WKUP_UART0 pinmux as it is used by SYSFW
to print diagnostic messages.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Introduce a framework that allows loading the System Firmware (SYSFW)
binary as well as the associated configuration data from an image tree
blob named "sysfw.itb" from an FS-based MMC boot media or from an MMC
RAW mode partition or sector.
To simplify the handling of and loading from the different boot media
we tap into the existing U-Boot SPL framework usually used for loading
U-Boot by building on an earlier commit that exposes some of that
functionality.
Note that this initial implementation only supports FS and RAW-based
eMMC/SD card boot.
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
On some platform we have sufficient memory available early on to allow
setting up and using a basic BSS prior to entering board_init_f(). Doing
so can for example be used to carry state over to board_init_r() without
having to resort to extending U-Boot's global data structure.
To support such scenarios add a Kconfig option called CONFIG_SPL_EARLY_BSS
to allow moving the initialization of BSS prior to entering board_init_f(),
if enabled. Note that using this option usually should go along with using
CONFIG_SPL_SEPARATE_BSS and configuring BSS to be located in memory
actually available prior to board_init_f().
Signed-off-by: Andreas Dannenberg <dannenberg@ti.com>
With changes in the driver requiring phy related properties,
add the same for the SD card node to prevent breaking boot with
the driver update.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Sync the sdhci0 node from kernel. This changes the compatible that is
required to be there in the driver. Change the same for the SD card node
which is not yet supported in kernel. This also syncs the main_pmx0 node
as a side effect.
Also change the name of the driver to match the compatible in kernel.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
We should use predefined constants instead of magic numbers.
Move some constant definitions from include/pe.h to
include/asm-generic/pe.h.
Use these constants in crt0_*_efi.S.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
So far USB was not enabled for the Allwinner H6 boards, as the PHY
driver was not ready and the clock gates were missing. Since this is now
fixed, let's add the PHY and the OHCI/EHCI drivers to the build, for
all existing H6 boards.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Probably for no particular reason SUNXI_GPIO was still defined the "old
way", in header files only.
Introduce SUNXI_GPIO to the Kconfig file in drivers/gpio to remove
another line from our dreadful config_whitelist.txt.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Corentin Labbe <clabbe.montjoie@gmail.com> # Pine-H64
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add some basic line delay values to be used with DDR3 DRAM chips on
some H6 TV boxes.
Taken from a register dump after boot0 initialised the DRAM.
Put them as the default delay values for DDR3 DRAM until we know better.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add a routine to program the timing parameters for DDR3-1333 DRAM chips
connected to the H6 DRAM controller.
The values were gathered from doing back-calculations from a register
dump, trying to match them up with the official JEDEC DDDR3 spec.
If in doubt, the register dump values were taken for now, but the JEDEC
recommendation were added as a comment.
Many thanks to Jernej for contributing fixes!
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
At the moment the H6 DRAM driver only supports LPDDR3 DRAM.
Extend the driver to cover DDR3 DRAM as well.
The changes are partly motivated by looking at the ZynqMP register
documentation, partly by looking at register dumps after boot0/libdram
has initialised the controller.
Many thanks to Jernej for contributing some fixes!
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Currently the H6 DRAM driver only supports one kind of LPDDR3 DRAM.
Split the timing parameters for this LPDDR3 configuration into a
separate file, to allow selecting an alternative later at compile time
(as the sunxi-dw driver does).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The DRAM controller manual suggests to first program the PHY
initialisation parameters to the PHY_PIR register, and then set bit 0 to
trigger the initialisation. This is also used in boot0.
Follow this recommendation by setting bit 0 in a separate step.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Using memcpy() is, however tempting, not a good idea: It depends on the
specific implementation of memcpy, also lacks barriers. In this
particular case the first registers were written using 64-bit writes,
and the last register using four separate single-byte writes.
Replace the memcpy with a proper loop using the writel() accessor.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Tested-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add mcu cpsw and its components along with scm_conf node
to have ethernet functional.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
The Beelink X2 is an STB based on the Allwinner H3 SoC with a uSD slot,
2 USB ports( 1 * USB-2 Host, 1 USB OTG), a 10/100M ethernet port using the
SoC's integrated PHY, Wifi via an sdio wifi chip, HDMI, an IR receiver, a
dual colour LED and an optical S/PDIF connector.
Linux commit details about the sun8i-h3-beelink-x2.dts sync:
"ARM: dts: sun8i: h3: Add ethernet0 alias to Beelink X2"
(sha1: cc4bddade114b696ab27c1a77cfc7040151306da)
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Since we have limited resources in SPL, it is the best interest
to keep the SPL as small as possible and that includes the DTB.
There are a few items in the device tree that can be removed,
because these boards don't use them.
Signed-off-by: Adam Ford <aford173@gmail.com>
The MMC card-detect pin was incorrectly defined which was fixed.
This patch resync's the dts and removes the u-boot specific fix.
Signed-off-by: Adam Ford <aford173@gmail.com>
The USE_TINY_PRINTF symbol only changes things within SPL and TPL
builds, so make it depend on that support. Next, make it default as
within these cases we should rarely have need of more advanced print
formats outside of the debug context.
To do this, in a few cases we need to correct our Kconfig dependencies
as we had cases of non-SPL targets select'ing this symbol. Finally, in
the case of a few boards we really do need the full printf
functionality.
Signed-off-by: Tom Rini <trini@konsulko.com>
This converts LEGO MINDSTORMS EV3 to the driver model. MMC, SERIAL, SPI
and SPI_FLASH are converted.
The device tree contains only the minimal nodes required by U-Boot
since the size of U-Boot is limited to 256K on this device.
Signed-off-by: David Lechner <david@lechnology.com>
Since pinctrl_stm32 driver update, each gpio bank is now binded
by pinctrl driver. The compatible string "st,stm32-gpio" becomes
useless, remove it.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/bsec.c: In function 'stm32mp_bsec_read':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (offset >= STM32_BSEC_OTP_OFFSET) {
^~
arch/arm/mach-stm32mp/bsec.c: In function 'stm32mp_bsec_write':
warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if (offset >= STM32_BSEC_OTP_OFFSET) {
^~
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch solves the following warnings:
arch/arm/mach-stm32mp/cpu.c:378:16: warning: comparison between signed
and unsigned integer expressions [-Wsign-compare]
if (instance > ARRAY_SIZE(serial_addr))
^
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add support of Trusted boot chain with OP-TEE
- reserved 32MB at the end of the DDR for OP-TEE
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Synchronize device tree with v5.2-rc4 label and
update the associated u-boot dtsi.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Tested-by: Pierre-Jean Texier <pjtexier@koncepto.io>
U-Boot should disable nodes in device tree if needed according
ETZPC status in ft_system_setup().
ETZPC itself use an array on addresses to do the match between the status
bits and the node.
Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add IPCC mailbox support on stm32mp157 eval and disco boards.
Signed-off-by: Fabien Dessenne <fabien.dessenne@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
- SPL SATA enhancements to allow booting from RAW SATA device
needed for Clearfog (Baruch)
- Enable SATA booting on Clearfog (Baruch)
- Misc changes to Turris Omnia (Marek)
- Enable CMD_BOOTZ and increase SYS_BOOTM_LEN on crs305-1g-4s
(Luka)
- Enable FIT support for db-xc3-24g4xg (Chris)
- Enable DM_SPI on Keymile Kirkwood board with necessary changes
for this (Pascal)
- Set 38x and 39x AVS on lower frequency (Baruch)
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
-----BEGIN PGP SIGNATURE-----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=X9wS
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2019.10' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2019.10
- import DT updates from Linux
- add UniPhier SPI controller driver
- make U-Boot image for 64bit SoCs position independent
- tidy up various init code for next generation SoCs
- misc cleanups
The board_early_init_f() inits clock before initing pinmux. However,
the clock configuration code might need to adjust PMIC settings of a
PMIC on I2C bus (e.g. board/ti/am335x/board.c does that). If the I2C
bus pin muxing is not configured before attempting to communicate
with the PMIC, the communication will silently fail and the prcm_init()
may configure fast enough CPU clock that the default voltage provided
by the PMIC would be insufficient and the platform would become
unstable.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Tom Rini <trini@konsulko.com>
The name CONFIG_LEGACY_IMAGE_FORMAT reads slightly better along with
allowing us to avoid a rather nasty Kbuild/Kconfig issue down the line
with CONFIG_IS_ENABLED(IMAGE_FORMAT_LEGACY). In a few places outside of
cmd/ switch to using CONFIG_IS_ENABLED() to test what is set.
Signed-off-by: Tom Rini <trini@konsulko.com>
Overload the weak function board_boot_order() so that besides choosing
the main boot device, we can fallback on USB boot by returning in the
BootROM, eg. if the NOR flash is empty while it was the primary boot
medium.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The _main call is not supposed to return at all: don't link the
branch.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Implement the weak board_return_to_bootrom() function so that when
enabling the spl_bootrom.c driver, one can make use of usbboot on
spear platforms. All necessary information to return to the BootROM
are stored in the BootROM's stack. The SPL stack pointer is reset so
we save the BootROM's stack pointer into the SPL .data section.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
There is no reason to do the few spear-related initialization, in a
different procedure than 'reset'. Spare one branching and get a linear
code flow by removing this indirection.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The link register is stored in R14. ARM assembly code allows to use
the 'lr' name to reference it instead of 'r14' which is not very
meaningful. Do the substitution to ease the reading.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Quoting ARM "RealView Compilation Tools Assembler Guide v4.0":
PUSH and POP are synonyms for STMDB and LDM (or LDMIA), with
the base register sp (r13), and the adjusted address written
back to the base register.
PUSH and POP are the preferred mnemonic in these cases.
Let's follow this recommandation to ease the reading and substitute
LDMIA/STMDB operations with PUSH/POP mnemonics.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Before cleaning a bit further the spear/start.S file, apply a few
cosmetic changes: capital letters, comment indentation and small
rewriting.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This comment describes the board state at the moment where we enter
the SPL. The description is entirely wrong; re-write it to fit the
reality.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
SPL BSS lies in SRAM and is actually initialized to 0 by the SPL in
arch/arm/lib/crt0.S:_main(), which is called by cpu_init_crit.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
It is clearly stated that board_init_f should *not* call
board_init_r. Indeed, board_init_f should return. The code will
continue through arch/arm/lib/crt0.S which will do more setup before
calling board_init_r.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reduce Auto Voltage Scaling VDD limit when core frequency is lower than
1600MHz. This reduces core voltage level from 1.25V to 1.15V, which
saves power.
The code is taken from Marvell's U-Boot 2013.01 revision 18.06.
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
KM Kirkwood boards now implement the driver model for its SPI flash
interface. Therefore, the old board specific claim and release functions
can be deleted. The preprocessor definition CONFIG_SYS_KW_SPI_MPP is yet
unused as well. All its appearances and dependencies are removed in the
kirkwood_spi driver, header files and finally the configuration whitelist.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
In order to migrate the SPI flash interface to the driver model, the SPI
configuration needs to be added in the KM Kirkwood device tree file.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Signed-off-by: Stefan Roese <sr@denx.de>
As preparation for the upcoming transferring of configurations from header
files to Kconfig, a common Kconfig file for all KM boards was created. For
the moment, it only sources the other three, more specific, Kconfig files.
Therefore, the architecture Kconfig files now include the common Kconfig
file. Also, the configuration selection for KM boards was moved from the
architecture Kconfig files to the board specific Kconfig files.
Signed-off-by: Pascal Linder <pascal.linder@edu.hefr.ch>
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Mario Six <mario.six@gdsys.cc>
Cc: Prabhakar Kushwaha <prabhakar.kushwaha@nxp.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable SATA peripherals in SPL to allow boot from SATA.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Add the required Kconfig and macro definitions to allow boot from SATA
on Armada 38x systems.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
SPL does not initialize mbus_dram_info. Don't change the ahci mbus
settings of the ROM. This allows the ahci to work in SPL.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
The base of DRAM will be changed for the next generation SoC.
The addresses needed for booting the kernel should be shifted
according to the DRAM base.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base of DRAM will be changed for the next generation SoC.
Set the base address to the 'dram_base' environment variable, which
will be useful for scripting.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base of DRAM will be changed for the next generation SoC.
To support it along with existing SoCs in the single defconfig,
set 'loadaddr' at boot-time by adding the offset to the DRAM base.
CONFIG_SYS_LOAD_ADDR is still hard-coded for compilation, but the
value from environment variable 'loadaddr' should be used.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The base address of DRAM was 0x80000000 for all the ARM SoCs of this
family in the past. It will be changed to 0x20000000 for a planned new
SoC. To support multiple SoCs by the single uniphier_v8_defconfig, the
base must be run-time determined.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, mem_map is hard-coded, and it worked well until the last
SoC. For a planned new SoC, the addresses of peripherals and DRAM
will be changed. Set it up run-time.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Currently, dram_init() code relies on the fact the DRAM size
configuration exists in the SG_MEMCONF register.
This will no longer be true for a planned new SoC, which will
replace SG_MEMCONF with a different register.
Refactor the hook in a more generic way.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Until the last SoC, the register addresses have been hard-coded because
they are always constant. For a planned new SoC, the register bases
will be completely changed. I insist on supporting multiple SoCs/boards
by a single defconfig (uniphier_v8_defconfig) since duplicating similar
defconfig files is a maintenance burden. The base addresses must be
fixed-up at run-time somehow.
Previously, the board init code identified the SoC by reading out the
SG_REVISION register. This is much easier than parsing DT.
You cannot do it any more because the base address of SG will be
changed. The SG_REVISION register exists to read out the SoC ID, but
you never know its address before identifying the SoC. Oh well.
So, the possible solution is to parse the DT, and find out the node
with "*-soc-glue" compatible string. Then, sg_base is set to the value
of the "reg" property. The sc_base is set up likewise.
It is worth noting a pit-fall. Having sc_base and sg_base in the global
scope will make the life easier, but the global variables are poorly
supported before the relocation. In fact, the .bss section overwraps
with DT. Allocating them in the .bss section would break DT. So, I gave
dummy initializers to assign them in the .data section.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The SC_* macros represent the address of SysCtrl registers.
For a planned new SoC, its base address will be changed.
Turn the SC_* macros into the offset from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The SG_* macros represent the address of SoC-glue registers.
For a planned new SoC, its base address will be changed.
Turn the SG_* macros into the offset from the base address.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The planned new SoC does not have SBC (System Bus Controller) block.
Make boot_is_swapped() an optional hook.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_MICRO_SUPPORT_CARD is enabled, U-Boot initialize SBC
(System Bus Controller), which may not be really necessary.
Check the "socionext,uniphier-system-bus" node in DT run-time.
If and only if it is found and its "status" property is okay,
initialize the SBC block.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If CONFIG_MICRO_SUPPORT_CARD is enabled, U-Boot tries to get access
to the devices on the support card, which may not actually exist.
Check the DT and search for the on-board devices run-time. If the
nodes are not found in DT, then disable the code.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This file calls readl(), so needs to include <linux/io.h>.
Currently, it relies on someone else including it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that 64-bit SoCs of this SoC family no longer support SPL,
this Makefile can be slightly simpler.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The .boot_device_fixup() is only called by SPL.
Now that 64-bit SoCs of this SoC family no longer support SPL,
debug-uart-ld20.c is never compiled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
[ Linux commit aa38571246c6ac279ebebd141157297bcb959d76 ]
The memory regions specified by /memreserve/ are passed to
early_init_dt_reserve_memory_arch() with nomap=false, so it is
not suitable for reserving memory for Trusted Firmware-A etc.
Use the more robust /reserved-memory node with the no-map property
to prevent the kernel from mapping it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
By default, CONFIG_SYS_INIT_SP_BSS_OFFSET was made invisible by not
giving a prompt to it.
The only way to define it is to hard-code an extra entry in SoC/board
Kconfig, like arch/arm/mach-tegra/tegra{186,210}/Kconfig.
Add a prompt to it in order to allow defconfig files to specify the
value of CONFIG_SYS_INIT_SP_BSS_OFFSET.
With this, CONFIG_SYS_INIT_SP_BSS_OFFSET would become always visible.
So, we need a new bool option to turn it off by default.
I move the 'default 524288' to the common place. This value is not too
big, but is big enough to avoid the overwrap of DT in most platforms.
If 512KB is not a suitable choice for your platform, you can change it
from your defconfig or menuconfig etc.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJdJEZEAAoJEB6zHgIOrC/I+LAH/jUDQpF5I68h0ZFGm3xoyGhm
3CSv8viOm/kL+GLubjnv4cwAp8N8VRpeJekz0Jt1Xp8C6OIgtnJ2Fln72KD+Z0IC
Rq7ByRS16iq4b6IUDRZObE4Jzxmf7rXU3jr0+/vd/en7kxVlvA9+Gsffs3OTGxC7
z9PysRZPBMH/smIPXdEQxYifnbpDG4fmfGcUWKrYfkB0Kq6Ep98Ia/gXNCY8XJ/A
sbNQGjJWJZWXS/TDetcC2VikssJ+yNFF34uzV+HD5Y3DW6ywLhuoDOz1pg8RR36i
YjcTCQz8lL/UVaUzrGUgPVAC3gdKY6J26GtV3vZavxBcmtGf0FhVtXO/tZc9AsY=
=6G45
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-2019.10-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel features and fixes for 2019.10 cycle
This includes the Atmel QSPI driver and support for the at91 boards.
This is the port of the driver from Linux, mostly done by Tudor Ambarus.
Fix the following:
- use "jedec,spi-nor" binding, we use jedec compatible flashes
- set bus width to 4, we use quad capable flashes
- differentiate bewteen data and clk and cs pins
- drop partions as we don't use them in u-boot.
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@microchip.com>
[tudor.ambarus@microchip.com: use "jedec,spi-nor", edit commit message]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
- add support for unique generated MAC adresses from SoC serial,
limited to Amlogic GXL/GXM boards for now
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BL1s
-----END PGP SIGNATURE-----
Merge tag 'u-boot-amlogic-20190704' of https://gitlab.denx.de/u-boot/custodians/u-boot-amlogic
- fix khadas-vim README
- add support for unique generated MAC adresses from SoC serial,
limited to Amlogic GXL/GXM boards for now
The watchdog of mediatek chips is enabled by bootrom before u-boot is
running. Previously we choose to enable the wdt driver only to disable the
watchdog hardware.
Now wdt service is enabled by default. The function arch_misc_init which is
only used to disable wdt is no longer needed.
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ryder Lee <ryder.lee@mediatek.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
Commit b238e4b00c ("rockchip: Cleanup of make_fit_atf.py.") set
firmware = "atf_1";
loadables = "uboot","atf_1","atf_2";
Actually it should be:
firmware = "atf_1";
loadables = "uboot","atf_2","atf_3";
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for generating an unique MAC address using the SoC internal
serial number from the Secure Monitor interface.
The algorithm generates an unicast locally administered 6bytes minus 2bits
address using an crc16 of the serial for the top 16bits with the lower 2 bits
masked to setup the unicast locally administered property and a crc24 for
the lower 24bits.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The Secure Monitor interface permits retrieving the SoC Serial Number,
add a function to retrieve it.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
After the transition to DM, only the mx6dl/solo wandboard
is supported.
Add FIT image support so that all the wandboard variants
can be supported, like it was prior to the DM conversion.
Successfully booted Linux on mx6q/solo/qp wandboards.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Place dtbs under SoC level rather than board level.
imx6q-novena.dtb and imx6dl-wandboard-revb1.dtb were
placed under the board config option, so move them
to SoC level.
This also aligns with the kernel dts Makefile format.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
rockchip pinctrl driver has update to use dts, so we need
to add the pinctrl config in SPL for sdmmc.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Migrate all the "u-boot,dm-pre-reloc" tag from rk3288-tinker.dts
into rk3288-tinker-u-boot.dtsi.
When both board level and soc level '-u-boot.dtsi' files exist,
we need to include the soc level 'rk3288-u-boot.dtsi' manually.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
TPL is at SRAM while other stage is at SDRAM, so it needs
separate STACK.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
More boards other than vyasa needs TPL, so enable the TPL configs
at chip level instead of board level.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Move the sg_set_pinsel macro to arch/arm/mach-uniphier/arm32/debug_ll.S
since it is not used anywhere else.
Move the C functions sg_set_{pinsel,iectrl} to debug-uart.c since they
are not used anywhere else.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
debug_uart_init() is called from spl_board_init(), which is only
compiled for SPL. For U-boot proper, _debug_uart_init() is unreachable,
so dropped by the dead code elimination.
Now that 64-bit SoCs of this SoC family no longer support SPL,
debug-uart-ld20.c is never compiled.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This file calls readl(), so needs to include <linux/io.h>.
Currently, it relies on someone else including it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
