FriendlyARM NanoPi R5S is an open-sourced mini IoT gateway device.
Board Specifications
- Rockchip RK3568
- 2 or 4GB LPDDR4X
- 8GB or 16GB eMMC, SD card slot
- GbE LAN (Native)
- 2x 2.5G LAN (PCIe)
- M.2 Connector
- HDMI 2.0, MIPI DSI/CSI
- 2xUSB 3.0 Host
- USB Type C PD, 5V/9V/12V
- GPIO: 12-pin 0.5mm FPC connector
The device tree is taken from kernel v6.4-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
The OrangePi R1 Plus LTS is a minor variant of OrangePi R1 Plus with
the on-board NIC chip changed from rtl8211e to yt8531c, and RAM type
changed from DDR4 to LPDDR3.
The device tree is taken from kernel v6.4-rc1.
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
The device tree and description are taken from kernel v6.3-rc1.
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Tianling Shen <cnsztl@gmail.com>
Add support for the DSI and DSI-DPHY to U-Boot for the RGxx3. These are
needed so we can send a panel ID request to determine which panel is
being used.
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The pinctrl on the Anbernic RGxx3 for the i2c2 bus does not use the
default value, so explicitly define it.
Fixes: 6cf6fe2537 ("board: rockchip: add Anbernic RGXX3 Series Devices")
Signed-off-by: Chris Morgan <macromorgan@hotmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the USB3.0 host node, and gadget node.
The gadget is available through the USB type C connector on the board.
The connector is tied to a Fairchild fusb302b device, which currently
does not have a driver in U-boot, but the node is here for correct
description of the board + Linux future compatibility.
It will be easier to move the node as-is when it will be available
in the DT from Linux
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add support for the USB 3.0 devices in rk3588:
- USB DRD(dual role device) 3.0 #0 as usbdrd3_0 which is available in
rk3588s
- USB DRD(dual role device) 3.0 #1 as usbdrd3_1 which is available in
rk3588 only
- USB DP PHY (combo USB3.0 and DisplayPort Alt Mode ) #0 phy interface
as usbdp_phy0
- USB DP PHY (combo USB3.0 and DisplayPort Alt Mode ) #1 phy interface
as usbdp_phy1
- USB 2.0 phy #2 , the USB 3.0 device can work with this phy in USB 2.0
mode
- associated GRFs (general register files) for the devices.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
[eugen.hristev@collabora.com: move nodes to right place, adapt from latest
linux kernel]
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Sync the devicetree with linux-next tag: next-20230525
Signed-off-by: Eugen Hristev <eugen.hristev@collabora.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 56670d6fb8 ("disk: part: use common api to lookup part
driver") part_get_info_by_name_type() ignores the part_type parameter
used to restrict the partition table type.
omap_mmc_get_part_size() and part_get_info_by_name() are the only
consumers.
omap_mmc_get_part_size() calls with part_type = PART_TYPE_EFI because at
the time of implementation a speed up could be gained by passing the
partition table type. After 5 years experience without this restriction
it looks safe to keep it that way.
part_get_info_by_name() uses PART_TYPE_ALL.
Move the logic of part_get_info_by_name_type() to part_get_info_by_name()
and replace the function in omap_mmc_get_part_size().
Fixes: 56670d6fb8 ("disk: part: use common api to lookup part driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This reverts commit d927d1a808, reversing
changes made to c07ad9520c.
These changes do not pass CI currently.
Signed-off-by: Tom Rini <trini@konsulko.com>
add support for x0-x17 registers used by the SMC calls
In SMCCC v1.2 [1] arguments are passed in registers x1-x17.
Results are returned in x0-x17.
This work is inspired from the following kernel commit:
arm64: smccc: Add support for SMCCCv1.2 extended input/output registers
[1]: https://documentation-service.arm.com/static/5f8edaeff86e16515cdbe4c6?token=
Signed-off-by: Abdellatif El Khlifi <abdellatif.elkhlifi@arm.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Jens Wiklander <jens.wiklander@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Enabling FIT_SIGNATURE required the old authentication method to be
disabled so disable this for K3 SOCs and enable FIT_SIGNATURE for K3
Platforms.
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
[ cleanup the patch ]
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
FIT signature requires the updates to u-boot.dtb and the DTB that we
pack don't get updates with the changes of the signature node.
Pack u-boot.dtb as the default DTB so that the signature node changes
can be reflected in them.
(Note, this is only packaging the primary platform and the secondary
platform will require manual changes for the FIT signature enablement)
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
[ add additional boards that were missing ]
Signed-off-by: Kamlesh Gurudasani <kamlesh@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The 'gsub' setexpr sub command is using when creating the FIT image
configuration string on K3 devices. Enable this for K3.
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
The background firewall calculations were wrong, fix that to determine
both the background and foreground correctly.
Fixes: 8bfce2f998 ("arm: mach-k3: common: reorder removal of firewalls")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Fix the regression that occurred during the alignment of binman series
merges along with these HS fixes that caused silent regression in this.
Fixes: 30a7ee87fd ("Kconfig: j721s2: Change K3_MCU_SCRATCHPAD_BASE to non firewalled region")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Fix regression occurred during refactoring for the mentioned commit.
Fixes: bd6a247593 ("arm: mach-k3: security: separate out validating binary logic")
Signed-off-by: Manorit Chawdhry <m-chawdhry@ti.com>
Since binman is used to package bootloader images for all K3 devices, we
do not have to rely on the earlier methods to package them.
Scripts that were used to generate x509 certificate for tiboot3.bin and
generate tispl.bin, u-boot.img have been removed.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Move to using binman to generate tispl.bin which is used to generate the
final flash.bin bootloader for iot2050 boards.
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
By providing entries in the binman node of the device tree, binman will
be able to find and package board config artifacts generated by
TIBoardConfig with sysfw.bin and generate the final image sysfw.itb.
It will also pick out the R5 SPL and sign it with the help of TI signing
entry and generate the final tiboot3.bin.
Entries for A72 build have been added to k3-j721e-binman.dtsi to
generate tispl.bin and u-boot.img.
Support has been added for both HS-SE(SR 1.1), HS-FS(SR 2.0) and GP images
In HS-SE, the encrypted system firmware binary must be signed along with
the signed certificate binary.
HS-SE:
* tiboot3-j721e_sr1_1-hs-evm.bin
* sysfw-j721e_sr1_1-hs-evm.itb
* tispl.bin
* u-boot.img
HS-FS:
* tiboot3-j721e_sr2-hs-fs-evm.bin
* sysfw-j721e_sr2-hs-fs-evm.itb
* tispl.bin
* u-boot.img
GP:
* tiboot3.bin -->tiboot3-j721e-gp-evm.bin
* sysfw.itb --> sysfw-j721e-gp-evm.itb
* tispl.bin_unsigned
* u-boot.img_unsigned
It is to be noted that the bootflow followed by J721E requires:
tiboot3.bin:
* R5 SPL
* R5 SPL dtbs
sysfw.itb:
* TIFS
* board-cfg
* pm-cfg
* sec-cfg
* rm-cfg
tispl.bin:
* DM
* ATF
* OP-TEE
* A72 SPL
* A72 SPL dtbs
u-boot.img:
* A72 U-Boot
* A72 U-Boot dtbs
Reviewed-by: Simon Glass <sjg@chromium.org>
[afd@ti.com: changed output binary names appropriately]
Signed-off-by: Andrew Davis <afd@ti.com>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Board config binary artifacts must be generated to be used by binman to
package sysfw.itb and tiboot3.bin for all K3 devices.
For devices that follow combined flow, these board configuration
binaries must again be packaged into a combined board configuration
blobs to be used by binman to package tiboot3.bin.
Add common k3-binman.dtsi to generate all the board configuration
binaries needed.
Also add custMpk.pem and ti-degenerate-key.pem needed for signing GP and
HS bootloader images common to all K3 devices.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Use spl_dcache_enable, in place of setup_dram, arch_reserve_mmu to set
up pagetable, initialise DRAM and enable Dcache to avoid multiple
function calls.
Check for CONFIG_SPL_VIDEO in place of CONFIG_SPL_VIDEO_TIDSS to prevent
any build failure in case video config is not defined and video related
functions are called.
Check for CONFIG_SPL_SPLASH_SCREEN and CONFIG_SPL_BMP before calling
splash_display to avoid compilation failure.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
In spl_dcache_enable after setting up page table, set gd->relocaddr
pointer to tlb_addr, to get next location to reserve memory. Align
tlb_addr with 64KB address.
Signed-off-by: Nikhil M Jain <n-jain1@ti.com>
Reviewed-by: Devarsh Thakkar <devarsht@ti.com>
There is little need to print the devstat information or when we exit a
function during a typical boot. Remove them to reduce the noise during
typical operation
Signed-off-by: Bryan Brattlof <bb@ti.com>
The function declaration for force_emif_self_refresh takes no parameters
but does not specify this, only the prototype in the headers do. As
clang will warn about this, correct it.
Signed-off-by: Tom Rini <trini@konsulko.com>
AM62x SoC is available in multiple variant:
- CPU cores (Cortex-A) AM62x1 (1 core), AM62x2 (2 cores), AM62x4 (4 cores)
- GPU AM625x with GPU, AM623x without GPU
- PRU (Programmable RT unit) can be present or not on AM62x2/AM62x4
Remove the relevant FDT nodes by reading the actual configuration
from the SoC registers, with that change is possible to have a single
dts/dtb file handling the different variant at runtime.
While removing GPU node and CPU nodes also the watchdog node
in the same Module Domain is removed.
A similar approach is implemented for example on i.MX8 and STM32MP1 SoC.
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Add register address and relevant bitmasks and shifts.
Allow reading these information:
- device identification
- number of cores (part of device identification)
- features (currently: PRU / no PRU)
- security
- functional safety
- speed grade
- temperature grade
- package
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Davis <afd@ti.com>
ft_system_setup cannot be enabled on SoC without msmc sram otherwise
fdt_fixup_msmc_ram function fails causing system reset.
Fix by moving fdt_fixup_msmc_ram to common_fdt.c file and creating
SoC (AM654, J721E and J721S2) specific files for fdt fixups.
This change was verified to not change anything on any existing board
(all the J721S2, AM654 and J721E boards requires it,
none of the remaining k3 boards require it).
Fixes: 30e96a2401 ("arm: mach-k3: Move MSMC fixup to SoC level")
Signed-off-by: Emanuele Ghidoli <emanuele.ghidoli@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
On security enforced (HS-SE) devices ROM firewalls OSPI data region3 that
is present in above 64bit region. Open this up in bootloader to allow
Linux to access OSPI flashes in mmap mode.
Without this kernel will crash when accessing this region due to
firewall violations on HS-SE devices.
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
For once this adds USB support for two SoCs: the H616 and the F1C100s
series. The rest is support for LPDDR3 DRAM chips on H616 boards.
Gitlab CI passed, and I booted that briefly on an H616 and an F1C200s
board. I don't have an H616 board with LPDDR3 DRAM, but reportedly that
works for Mikhail, and doesn't regress on my DDR3 boards.
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCZLqHzgAKCRDKSWXLKUoM
IcdEAKCSgy0lMxb1c0adCjpkQR9x63oKbQCdGiioU+W+0moznHdI7+W2UptNt3w=
=Uzn8
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2023.10-rc1-v2' of https://source.denx.de/u-boot/custodians/u-boot-microblaze
Xilinx changes for v2023.10-rc1 v2
axi_emac:
- Change return value if RX packet is not ready
cadence_qspi:
- Enable flash reset for Versal NET
dt:
- Various DT syncups with Linux kernel
- SOM - reserved pmufw memory location
fpga:
- Add load event
mtd:
- Add missing dependency for FLASH_CFI_MTD
spi/nand:
- Minor cleanup in Xilinx drivers
versal-net:
- Prioritize boot device in boot_targets
- Wire mini ospi/qspi/emmc configurations
watchdog:
- Use new versal-wwdt property
xilinx:
- fix sparse warnings in various places ps7_init*
- add missing headers
- consolidate code around zynqmp_mmio_read/write
- switch to amd.com email
zynqmp_clk:
- Add handling for gem rx/tsu clocks
zynq_gem:
- Configure mdio clock at run time
zynq:
- Enable fdt overlay support
zynq_sdhci:
- Call dll reset only for ZynqMP SOCs
To sync with the upstream code, removed 'snps,enable_guctl1_resume_quirk'
quirk for usb. This quirk is no more available in linux after the xilinx
release 2022.2.
This functionality is taken care of by the 'snps,resume-hs-terminations'
quirk.
Signed-off-by: Piyush Mehta <piyush.mehta@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/4b7a132116bf0248cdb558e04de3b06b412c4a0f.1688992653.git.michal.simek@amd.com
Explicitly specify interrupt affinity to avoid HW perfevents
need to guess. This avoids the following error upon linux boot:
armv8-pmu pmu: hw perfevents: no interrupt-affinity property,
guessing.
Reported-by: John Toomey <john.toomey@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c2f55a10cf54c6004f5dfe2ea18bcb4cf04f5723.1688992653.git.michal.simek@amd.com
Linux kernel throws "cacheinfo: Unable to detect cache hierarchy for
CPU 0" warning when booting on zu+ Soc. To fix it add the L2 cache
node and let each CPU point to it.
Reported-by: John Toomey <john.toomey@amd.com>
Signed-off-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/c8dfabab12c97922aaad7fa91be0cbc7e4021528.1688992653.git.michal.simek@amd.com
The commit a4180c3696 ("arm64: zynqmp: Add mode-pin GPIO controller DT
node") added usb phy reset over bootmode pins by default on usb0 only.
zcu100 is using usb0 as peripheral and usb1 as host. Unfortunately reset
line is shared for both usb ulpi phys but usb_rst_b is connected to usb5744
hub which is used only in host mode. Especially this chip requires reset to
operate properly that's why better assign gpio reset to usb1 instead of
usb0.
Without this change usb start crashed when runs.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/1ca80ec5bf7a595c03822f3e4e3683298205067a.1688992653.git.michal.simek@amd.com
Extend compatible versions for K24 SOM.
Changes are not affecting SW behavior that's why all versions are
compatible to each other.
Describing all revisions is done by purpose because user space SW is
reading compatible string for logic around DT overlays and bitstreams.
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/92eba01ac316e58bd2d3508b0e63bbfafbedbb73.1688992653.git.michal.simek@amd.com
Increase reset assert time for TI SGMII PHY on KR260 CC starting
6.1 kernel. This PHY does not come out of reset with the existing
100us pulse width as per testing on multiple carrier cards. The reset
is driven via a PCA9570 I2C expander. The expander driver was updated
to an upstream version in 6.1 where gpio_chip _set was optimized.
Delays in earlier kernels may have masked this issue. This is a safe
workaround value for assert pulse width before the discussions are
resolved with TI.
Signed-off-by: Harini Katakam <harini.katakam@amd.com>
Reviewed-by: Radhey Shyam Pandey <radhey.shyam.pandey@amd.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/8fb9f17d43a43ef504c9f29006cd686cce8ac98b.1688992653.git.michal.simek@amd.com
Add support for Versal NET mini Octal SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Octal SPI
related settings are enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-3-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Add support for Versal NET mini Quad SPI flash configuration. This runs
from onchip memory, so it has to be compact. Hence only Quad SPI
related settings are enabled.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614121351.21521-2-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
Enable flash reset functionality for Versal NET platform.
In cadence_qspi.c there is weak function defined for reset, hence remove
the check for config, so that it will work for Versal and Versal NET
platforms.
Add register defines in Versal NET hardware.h for mini U-Boot flash
reset.
Add read_delay initialization for Versal NET also.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@amd.com>
Link: https://lore.kernel.org/r/20230614120452.21019-1-ashok.reddy.soma@amd.com
Signed-off-by: Michal Simek <michal.simek@amd.com>
PMUFW requires top 1MB of the lower DDR memory reserved for its operation,
this is missing in k26/k24 sm static dts files because of which U-Boot
throws warning messages "efi_free_pool: illegal free" as EFI puts
some code to that space which shouldn't happen.
Signed-off-by: Sharath Kumar Dasari <sharath.kumar.dasari@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@amd.com>
Link: https://lore.kernel.org/r/57452d16df2d48593de206bebf877d2c2cfe7bf1.1685966389.git.michal.simek@amd.com
The H616 SoC has support for several types of DRAM: DDR3, LPDDR3,
DDR4 and LPDDR4.
At the moment, the driver only supports DDR3 memory.
Let's extend the driver to support the LPDDR3 memory. All "magic"
values obtained from the boot0.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Acked-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Allwinner H616 SoC supports several types of DRAM memory. To further
integrate other types of memory, we need to add this delimitation.
Signed-off-by: Mikhail Kalashnikov <iuncuim@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Currently there is one DRAM parameter struct for the Allwinner H616 DRAM
"driver". It contains many fields that are compile time constants
(set by Kconfig variables), though there are also some fields that are
probed and changed over the runtime of the DRAM initialisation.
Because of this mixture, the compiler cannot properly optimise the code
for size, as it does not consider constant propagation in its full
potential.
Help the compiler out by splitting that structure into two: one that only
contains values known at compile time, and another one where the values
will actually change. The former can then be declared "const", which will
let the compiler fold its values directly into the code using it.
We also add "const" tags for some new "struct dram_config" pointers, to
further increase code optimisation.
To help the compiler optimise the code further, the definition of the
now "const struct dram_para" has to happen at a file-global level, so
move that part out of sunxi_dram_init().
That results in quite some code savings (almost 2KB), and helps to keep
the code small with the LPDDR3 support added later.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
There are quite some functions in the Allwinner H616 DRAM "driver", some
of them actually change the parameters in the structure passed to them,
but many are actually not.
To increase the optimisation potential for the code, mark those functions
that just read members of the passed dram_para struct as "const".
This in itself does not decrease the code size, but lays the groundwork
for future changes doing so.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
The usage of the C keyword "inline" seems to be a common
misunderstanding: it's a *hint* only, and modern compilers will inline
(or not) functions based on their own judgement and provided compiler
options.
So while marking functions as "inline" does not do much, missing the
"static" keyword will force to compiler to spell out a version of the
function for potential external callers, which actually increases the
code size (though hopefully the linker will drop the function).
Change the "inline" attribute for the mbus_configure_port() functions in
some Allwinner DRAM drivers to "static", so that the explicit version
can actually be dropped from the object file, reducing the code size.
"static inline" has a use case in header files, where it avoids a warning
if a .c file including this header does not use the particular function.
In a .c file itself "static inline" is not useful otherwise, so just use
static here as well.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
At the moment we use "select" in each Allwinner SoC's Kconfig section to
include the USB PHY driver in the build. This means it cannot be disabled
via Kconfig, although USB is not really a strictly required core
functionality, and a particular board might not even include USB ports.
Rework the Kconfig part by removing the "select" lines for each SoC's
section, and instead letting it default to "y" in the PHY driver section
itself. We use "depends on !" to exclude the few SoCs we don't support
(yet). The Allwinner V3s does not enable USB (PHY) support at the moment,
even though it should work: let the PHY default to "n" to keep the
current behaviour.
Also the MUSB USB driver directly calls some functions from the PHY
driver, so let the former depend on the PHY driver.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Sam Edwards <CFSworks@gmail.com>
These boards use SPL in a mkimage entry and apparently access the symbol
containing the image position of U-Boot, but put U-Boot in another
image. This means that binman is unable to fill in the symbol correctly
in the SPL binary.
This doesn't matter at present since mkimage doesn't support symbol
writing. But with the upcoming conversion to a section, it will. So add
a property to disable symbol writing.
Signed-off-by: Simon Glass <sjg@chromium.org>
With gcc-13.1 we get a warning about enum vs int here, so correct the
declaration to match the implementation.
Signed-off-by: Tom Rini <trini@konsulko.com>
The sar-reg0 alias was left over from an earlier iteration of the
patches adding support for this board. Remove the unused alias.
Fixes: 6cc8b5db40 ("arm: mvebu: Add RD-AC5X board")
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The x240 and SE240 are a series of L2+ switches from Allied Telesis.
There are a number of them in the range but as far as U-Boot is
concerned all the CPU block components are the same so there's only one
board defined.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Drive CTRL_SLEEP_MOCI# high at boot (SPL) using a GPIO hog, this signal
may be used to control some power-rails on the carrier board, therefore
it should be set to high when the module is booting.
To do this as early as possible is generally a good idea and the issue
was noticed on the Yavia carrier board where it is needed to power the
I2C EEPROM on the carrier board.
Signed-off-by: Andrejs Cainikovs <andrejs.cainikovs@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
The USB Power domains should not have been removed as it causes
the board to hang if the USB is started.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Several changes have been made to the device tree
in the kernel, so update that as well as the
corresponding imx8mp-u-boot.dtsi files to prevent
breaking the booting.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
For SOM with the EC configuration, the ethernet PHY is located on the
SOM itself, and connected to the CPU ethernet controller. It has a
reset line controlled via GPIO1_IO9. In this configuration, the PHY
located on the carrier board is not connected to anything and is
therefore not used.
For SOM without EC configuration, the ethernet PHY on the carrier
board is connected to the CPU ethernet controller. It has a reset line
controlled via the GPIO expander PCA9534_IO5.
The hardware configuration (EC) is determined at runtime by
reading from the SOM EEPROM.
To support both hardware configurations (EC and non-EC), adjust/fix
the PHY reset gpios according to the hardware configuration
read at runtime from the SOM EEPROM. This adjustement is done in
U-Boot (OF_BOARD_FIXUP) and kernel (OF_BOARD_SETUP) device trees.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Bitwise operations on signed integers are not defined,
replace them with per-call checks.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Marek Vasut <marex@denx.de>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Heiko Schocher <hs@denx.de>
In order to enable HAB, FSL_CAAM, ARCH_MISC_INIT and
SPL_CRYPTO should be enabled in Kconfig like other i.MX8M
boards.
This also needs to occur in the SPL so enable CONFIG_SPL_BOARD_INIT and
add a void spl_board_init function which calls arch_misc_init to probe
the CAAM driver.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
add support for SHA-256 secure hash algorithm using the ARM v8
SHA-256 instructions for verifying image hash.
Signed-off-by: Gaurav Jain <gaurav.jain@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Abstract common interfaces for AHAB authentication operations.
Then share some common codes for AHAB and SPL container authentication
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
If the container has image which conflicts with
spl_get_load_buffer address, there are processing failures.
Use malloc instead of spl_get_load_buffer.
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Nitin Garg <nitin.garg@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
1. Implement bootaux for the M4 boot on i.MX8QM and QXP. Users need to download
M4 image to any DDR address first. Then use the
"bootaux <M4 download DDR address> [M4 core id]" to boot CM4_0
or CM4_1, the default core id is 0 for CM4_0.
Since current M4 only supports running in TCM. The bootaux will copy
the M4 image from DDR to its TCML.
2. Implment bootaux for HIFI on QXP
command: bootaux 0x81000000 1
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The bootaux uses ulong to read private data and write to M4 TCM,
this cause problem on ARM64 platform where the ulong is 8bytes.
Fix it by using u32 to replace ulong.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The current bootaux supports i.MX8M and i.MX93, but the name "_M4_"
implies that the SoCs have Cortex-M4. Actually i.MX8MM/Q use Cortex-M4,
i.MX8MN/P use Cortex-M7, i.MX93 use Cortex-M33, so use "_MCU_" in place
of "_M4_" to simplify the naming.
Signed-off-by: faqiang.zhu <faqiang.zhu@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add the support for loading image from secondary container set on
iMX8QM B0, iMX8QXP C0.
Using the SCFW API to get container set index, if it is the secondary
boot, get the offset from fuse and apply to offset of current container
set beginning for loading.
Also override the emmc boot partition to check secondary boot and switch
to the other boot part.
This patch is modified from NXP downstream:
imx8: Fix the fuse used by secondary container offset
imx: container: Skip container set check for ROM API
imx8: spl: Support booting from secondary container set
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Checking container header tag and version is wrong, it causes to fail
to bypass invalid container
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix below coverity issues caused by get_idx function where "-1" is
compared with uint8_t "element"
343336 Unsigned compared with neg
343337 Operands don't affect result
Additional, this function returns "-1" will cause overflow to
event string array.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
On the imx8ulp A1 SoC, the ELE RNG needs to be manually started.
Signed-off-by: Clement Faure <clement.faure@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix Coverity (CID 21143558).
When tee_shm_register returns failure, the shm_input pointer is
invalid, should not free it. Same issue also exists on registering
shm_output.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Add two ELE API: ele_return_lifecycle_update and ele_write_secure_fuse
Add two cmd: ahab_return_lifecycle and ahab_sec_fuse_prog
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Fix build warning:
warning: format ‘%x’ expects argument of type ‘unsigned int’, but argument 3
has type ‘u64’ {aka ‘long long unsigned int’} [-Wformat=]
printf("can't find memreg for image %d load address 0x%x, error %d\n",
warning: format ‘%lx’ expects argument of type ‘long unsigned int’, but
argument 3 has type ‘sc_faddr_t’ {aka ‘long long unsigned int’} [-Wformat=]
debug("memreg %u 0x%lx -- 0x%lx\n", mr, start, end);
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Per NXP requirement, we rename all the NXP EdgeLock Secure Enclave
code including comment, folder and API name to ELE to align.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
The NF_CLK for the AC5 SoC runs at 400MHz. There's no strapping
or gating require so just add a mvebu_get_nand_clock() that
returns this value.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The AC5/AC5X SoC has a NAND flash controller. Add this to the
SoC device tree.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
- Update the Thecus N2350 DTS to conform with latest device-tree binding
and styles.
- Correct typo in mdio node.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Pali Rohár <pali@kernel.org>
The Gateworks imx8mp-venice-gw7905-2x consists of a SOM + baseboard.
The GW702x SOM contains the following:
- i.MX8M Plus SoC
- LPDDR4 memory
- eMMC Boot device
- Gateworks System Controller (GSC) with integrated EEPROM, button
controller, and ADC's
- PMIC
- SOM connector providing:
- eQoS GbE MII
- 1x SPI
- 2x I2C
- 4x UART
- 2x USB 3.0
- 1x PCI
- 1x SDIO (4-bit 3.3V)
- 1x SDIO (4-bit 3.3V/1.8V)
- GPIO
The GW7905 Baseboard contains the following:
- GPS
- microSD
- off-board I/O connector with I2C, SPI, GPIO
- EERPOM
- PCIe clock generator
- 1x full-length miniPCIe socket with PCI/USB3 (via mux) and USB2.0
- 1x half-length miniPCIe socket with USB2.0 and USB3.0
- USB 3.0 HUB
- USB Type-C with USB PD Sink capability and peripheral support
- USB Type-C with USB 3.0 host support
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
While testing the ethernet interface on a Variscite symphony carrier
board using an imx8mn SOM with an onboard ADIN1300 PHY (EC hardware
configuration), the ethernet PHY is not detected.
The ADIN1300 datasheet indicate that the "Management interface
active (t4)" state is reached at most 5ms after the reset signal is
deasserted.
The device tree in Variscite custom git repository uses the following
property:
phy-reset-post-delay = <20>;
Add a new MDIO property 'reset-deassert-us' of 20ms to have the same
delay inside the ethphy node. Adding this property fixes the problem
with the PHY detection.
Note that this SOM can also have an Atheros AR8033 PHY. In this case,
a 1ms deassert delay is sufficient. Add a comment to that effect.
Fixes: c4c1ed68c1 ("imx8mn_var_som: Add support for Variscite
VAR-SOM-MX8M-NANO board")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Select DM_ETH_PHY so that the reset-gpios property of the ethphy node
can be used.
Also select DM_PCA953X, which is needed for resetting the
ethernet PHY on the carrier board via the PCA9534 I/O expander.
Commit 4e5114daf9 ("imx8mn: synchronise device tree with linux") did
synchronise device tree with linux, which in effect removed obsolete
PHY reset properties and replaced them with new mdio DM
properties. But the commit didn't activate DM_ETH_PHY or DM_PCA953X.
Fixes: 4e5114daf9 ("imx8mn: synchronise device tree with linux")
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Enable support to read and display configuration/manufacturing infos
from 4Kbit EEPROM located on SOM board.
Note: CONFIG_DISPLAY_BOARDINFO is automatically selected for ARM arch.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Getting
Found /vpu_g1@38300000 node
Modify /vpu_g1@38300000:status disabled
Found /vpu_g2@38310000 node
Modify /vpu_g2@38310000:status disabled
etc. on the console on every boot is needlessly verbose. Demote the
"Found ..." lines to debug(), which is consistent with other instances
in soc.c.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
The CONFIG_PL011 used by all other ARCH_MX28 based boards is not
supporting DM_SERIAL. Instead, other define - namely CONFIG_PL01X_SERIAL
shall be used by boards supporting DM_SERIAL.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
When DM_SERIAL is enabled on mxs (i.e. imx28) platform, the console
early initialization must be postponed until the driver model is
correctly setup.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
As imx28 family of SoCs is NOT supporting the Common Clock Framework (CCF)
the 'clks' property shall NOT be enabled by default.
Without this change u-boot proper before relocation tries to bind driver
(which doesn't exists) for this device. As a result, pre-relocation DTB
parsing is finished with error and the board hangs in a very early stage
of u-boot proper boot process.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The imx287 SoC doesn't support common clock framework (CCF), so the
'clocks' property is removed to avoid early (i.e. in SPL) errors when
SPL_OF_PLATDATA is used.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The DM_SERIAL implicitly requires CONFIG_PL01X_SERIAL, which
allows support for both serial IP block versions (i.e. PL011 and
PL010).
The decision about used IP block is based on the compatible string,
when DM is used.
In the XEA, the OF_PLATDATA is used to allow usage of serial driver in
the SPL (as the size of SPL is crucial). In this case one cannot extract
the type of IP block from .data field (corresponding to compatible) and
it must be explicitly read at probe from dtoc generated, u-boot specific
property.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After enabling DM_SERIAL for XEA board, the same serial shall be used
in the SPL (with SPL_OF_PLATDATA support).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After the commit (SHA1: 7d08ddd09b) some
u-boot specific XEA FEC related properties have been replaced by ones
from the Linux kernel.
To be more specific - XEA board (and imx287 in general) has built L2
switch connected to FEC, which needs some special treatment.
In u-boot it is handled with 'mac0' node, whereas Linux uses dedicated
switch DTS node.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
After the re-sync with Linux Kernel's DTS
(SHA1: 7d08ddd09b), the XEA's
descripion has nodes and properties, which are NOT utilized
in the u-boot.
To avoid confusion - those are deleted.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
The IMX28 PMU (Power Management Unit) has a dedicated Linear Regulator
to produce (by default) 4.2V output - available outside the chip as
VDD_4P2.
When system is supposed to not use VDD5V as a main power source - instead
the DCDC_BATT is used; it is safe to disable this regulator.
As the in-PMU DCDC switching regulator (from which DCDC_VDDA, DCDC_VDDIO
and DCDC_VDDD are generated) can be driven from DCDC_BATT or output
of this 4P2 regulator - by disabling the latter the use of the DCDC_BATT
is forced.
To be more specific - according to NXP's AN4199 the DCDC_BATT source is
preferred (over VDD5V), as more efficient and stable source for
industrial applications.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This new Kconfig option allows disabling the in-PMU battery charging
block. This may be required when DCDC_BAT source is powered not from
battery, but from already regulated, good quality source.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This option sets the current limit for 5V source to zero, so all
the PMU outputs are primarily powered from battery source (DCDC_BAT).
This option may be set on systems, where the 5V is NOT supposed to be
in any scenario powering the system - for example on systems where
DCDC_BAT is connected to fixed and regulated 4.2V source (so the
"battery" is not present).
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Change boot device logic to also allow environment stored in fat and
in ext4 when booting from SD or eMMC.
As the boot device check for SD and for eMMC was depending on
ENV_IS_IN_MMC being defined, change the ifdef blocks at
env_get_location to use IS_ENABLED instead for all modes, returning
NOWHERE when no valid mode is found.
This solution is based on (with added SPL support):
Link: https://lore.kernel.org/all/20211020191626.3648540-1-ricardo@foundries.io/
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
nodeoff variable should be variable off returned by fdt_path_offset() so
let's rename it to off.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
In order to use the FlexSPI interface in U-Boot, configure
the alias to make spi0 point to flexspi.
With that enabled, sf probe detects the QSPI part as:
SF: Detected n25q256ax1 with page size 256 Bytes, erase size 4 KiB, total 32 MiB
Signed-off-by: Adam Ford <aford173@gmail.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all".
In order to keep the serial nodes in sync with their representation in
the Linux dts, add these u-boot specific properties to *-u-boot.dtsi
files.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Pick up the serial node descriptions from Linux v6.3 for the ls1046ardb
and ls1046afrwy boards and their dependencies. Including the
fsl,qoriq-clockgen.h and arm-gic.h headers forces us to change the include
directives to explicitly go through the C preprocessor for all boards in
the ls1046a SoC family.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Make sure the serial driver is initialized before relocation by tagging
the serial nodes with "bootph-all".
In order to keep the serial nodes in sync with their representation in
the Linux dts, add these u-boot specific properties to *-u-boot.dtsi
files.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Pick up the serial node descriptions from Linux v6.3 for the ls1043ardb
board and its dependencies. Including the fsl,qoriq-clockgen.h and
arm-gic.h headers forces us to change the include directives to explicitly
go through the C preprocessor for all boards in the ls1043a SoC family.
Signed-off-by: Camelia Groza <camelia.groza@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Pass _image_binary_end to make a standard way to indicate the end
of the text section in SPL.
The motivation for this is to have a uniform way to handle
the SPL boundary checks.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Rename current assembler implementation of allow_unaligned() to
arm11_arch_cp15_allow_unaligned() and add it into arm11.h header,
then add C wrapper of allow_unaligned().
This fixes misbehavior when linking U-Boot, where the CPU specific
allow_unaligned() implementation was ignored and instead the
__weak allow_unaligned() implementation from lib/efi_loader/efi_setup.c
was used, which led to "data abort" just before booting Linux via tftp,
in efi_dp_from_file() -> path_to_uefi() -> utf16_put() .
The problem is triggerd by c7c0ca3767 ("efi_loader: fix efi_dp_from_file()") .
Adding the wrapper fixes the problem.
Fixes: d47a774680 ("arm: arm11: allow unaligned memory access")
Signed-off-by: Marek Vasut <marex@denx.de>
Rename current assembler implementation of allow_unaligned() to
v7_arch_cp15_allow_unaligned() and add it into armv7.h header,
then add C wrapper of allow_unaligned().
This fixes misbehavior when linking U-Boot on ARMv7a i.MX6Q, where the
CPU specific allow_unaligned() implementation was ignored and instead the
__weak allow_unaligned() implementation from lib/efi_loader/efi_setup.c
was used, which led to "data abort" just before booting Linux via tftp,
in efi_dp_from_file() -> path_to_uefi() -> utf16_put() .
The problem is triggerd by c7c0ca3767 ("efi_loader: fix efi_dp_from_file()") .
Adding the wrapper fixes the problem.
Fixes: 78f90aaeec ("arm: armv7: allow unaligned memory access")
Signed-off-by: Marek Vasut <marex@denx.de>
The HTC One X is a touchscreen-based, slate-sized smartphone
designed and manufactured by HTC that runs the Android operating
system. The One X features a 4.7" display, an Nvidia Tegra 3
quad-core chip, 1 GB of RAM and non-extendable 32 GB of internal
storage. UART-A is default debug port.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com>
Tested-by: Ion Agorria <ion@agorria.com>
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
LG X3 is a development board based on Nvidia Tegra 3 SoC
on base of which Optimus 4X HD and Optimus Vu were created.
Both smartphones feature a 4.7" and 5" panels respectively,
an Nvidia Tegra 3 quad-core chip, 1 GB of RAM and 16/32 GB
of internal storage. Optimux 4X HD additionally has a micro
SD slot.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # LG P880 T30
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Nexus 7 is a mini tablet computer co-developed by Google and Asus
that runs the Android operating system. The Nexus 7 features a 7"
display, an Nvidia Tegra 3 quad-core chip, 1 GB of RAM and 8/16 GB
of internal storage.
This patch brings support for all 3 known ASUS/Google devices:
- Nexus 7 (2012) E1565
- Nexus 7 (2012) PM269
- Nexus 7 (2012) 3G - tilapia
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # ASUS Grouper E1565
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
The ASUS Transformer T30 family are 2-in-1 detachable tablets
and AiO developed by ASUS that run the Android operating system
(TF600T runs Windows RT and P1801-T runs Android and Windows).
The T30 Transformers feature a 10.1-inch display (apart P1801-T),
an Nvidia Tegra 3 quad-core chip, 1/2 GB of RAM, and 16/32 GB of
storage. Transformers board derives from Nvidia Cardhu development
board.
This patch brings support for 7 known Transformer devices:
- ASUS Transformer Prime TF201
- ASUS Transformer Pad TF300T/TF300TG/TF300TL
- ASUS VivoTab RT TF600T (Windows RT based)
- ASUS Transformer Infinity TF700T
- ASUS Portable AiO P1801-T
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # all devices
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This is a small tool for calculation of SoC UID based on the same
Linux function. It can be further used for generation of device
unique data like mac address or exposing it as serial number.
Tested-by: Andreas Westman Dorcsak <hedmoo@yahoo.com> # ASUS Grouper E1565
Tested-by: Svyatoslav Ryhel <clamor95@gmail.com> # LG P895 T30
Signed-off-by: Svyatoslav Ryhel <clamor95@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
This commit adds functions to manage secure power domain for
Amlogic SoC's using smc functionality.
Signed-off-by: Alexey Romanov <avromanov@sberdevices.ru>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://lore.kernel.org/r/20230531093156.29240-2-avromanov@sberdevices.ru
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
