Since commit 06d514d77c ("lmb: consider EFI memory map") the EFI regions
are also pushed into the lmb if EFI_LOADER is enabled (which is by
default on most system). Which can cause the number of entries to go
over the maximum as it's default is only 8.
Specifically i ran into this case on an TI am62 which has an fdt with
4 reserved regions (in practice 3 lmb entries due to adjecent ranges).
As this is likely to impact more devices bump the default max
regions to 16 so there is a bit more slack.
Fixes: 06d514d77c ("lmb: consider EFI memory map")
Link: https://bugzilla.opensuse.org/show_bug.cgi?id=1207562
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
[trini: collect tags from the other equivalent patch]
As explained by Philippe Schenker, I was misinterpreting what happened
in the case where we do not set LMB_USE_MAX_REGIONS and so had
re-introduced the problem I was attempting to more widely resolve.
This reverts commit 007ae5d108.
Reported-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
When adding reserved memory areas from the EFI memory map set the NOMAP
flag when applicable. When this isn't done adding "no-map" flagged entries
from the fdt after receiving the same from the EFI memory map fails due
to non-matching flags.
Signed-off-by: Sjoerd Simons <sjoerd@collabora.com>
The LMB code allows for picking a hard limit on the number of regions it
can know of, or to dynamically allocate these regions. The reason for
this choice is to allow for the compiler to perform a size optimization
in the common case. This optimization however, is very small, ranging
from 196 bytes to 15 bytes saved, or in some cases, being larger. Now
that we also have more regions covered by LMB (in order to protect
various parts of our self at run time), the default of 8 is also much
easier to hit and leads to non-obvious error messages (which imply that
an area is protected, not that we're out of areas to add to the list).
Switch to the dynamic use as the default.
Signed-off-by: Tom Rini <trini@konsulko.com>
HandleProtocol() is deprecrated. According to the UEFI specification it
should be implemented as a call to OpenProtocolInterface() with a hard
coded agent handle. This implies that we would have to call
CloseProtocolInterfaces() after usage with the same handle.
Getting rid of an EFI_CALL() is also appreciated.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
There is no variable num_pages in function efi_esrt_allocate_install().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When this fails it can be time-consuming to debug. Add some debugging
to help with this. Also try to return error codes instead of just using
-1.
Signed-off-by: Simon Glass <sjg@chromium.org>
It is often useful to show an error code to give the user a clue as to
what went wrong. When error strings are compiled into U-Boot it is
possible to show a message as well.
But at present it is not very convenient, since code must check if the
error strings are present, then obtain the error string and use it in
a printf() string.
Add a %dE option which shows an error code along with an error string,
if available. This makes it easy to show one or both.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some environment variables provide a space-separated list of strings. It
is easier to process these when they are broken out into an array of
strings.
Add a utility function to handle this.
Signed-off-by: Simon Glass <sjg@chromium.org>
At this point, the remaining places where we have a symbol that is
defined as CONFIG_... are in fairly odd locations. While as much dead
code has been removed as possible, some of these locations are simply
less obvious at first. In other cases, this code is used, but was
defined in such a way as to have been missed by earlier checks. Perform
a rename of all such remaining symbols to be CFG_... rather than
CONFIG_...
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently the code that adds the CapsuleMax variable is under a
Kconfig named 'EFI_HAVE_CAPSULE_UPDATE. Git history only shows a
single occurrence of that. The IS_ENABLED should be checking for
EFI_HAVE_CAPSULE_SUPPORT
Reported-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
"Unable to find TPMv2 device" doesn't explain much with regards to the
error origin. Update it to match what we have in the RNG protocol
installation.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Currently file ubootefi.var is only created if the user sets a non-volatile
EFI variable. If the file is missing, a warning is written.
With the change PlatformLang is always persisted. So the file will exist on
second boot.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Before clearing the screen, ensure that no previous output of firmware
or UEFI programs will be overwritten on serial devices or other
streaming consoles. This helps generating complete boot logs.
Tested regarding multi-output against qemu-x86_defconfig. Still, there
were remaining concerns about side effects, so this is provided as an
opt-in feature.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Ensures a consistent background color of the whole screen for succeeding
outputs as both demanded by the spec and implemented in EDK2 as well.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmPIpV4RHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreZuqwgA0UpYQEX6/MegzHSCIx3AMT4rCF1Ytitr
LS4Cbvj1Q09Rt9jriW7wAV5AobVPwGf2L5SVcnWv2I9+MmypDIXEe8HIrt2fRFu9
bzn/2GOzXczuXqPFa/CWOUwjvCzTb8Sl9NtRszrP5NvOzuN15x00ZUYaXFO7fgsB
zZMzOKxemwjdtLaox+x+VIJ95HMDEkYrWTAqTPg74CNVSjRbbLNqNq0zqkHB8SnH
ubgphtIKYItTeIXcfIa9V4LeQp0ZitkzSfAibX+nIPCMPg9jbG9MrQQ+VvSZDjnM
y8wa8gFj47Ek+gGNFXMHIpO6tBd83uHRgtf2x+zhcovLELYnZ6fDGw==
=1K6m
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-18jan23' of https://source.denx.de/u-boot/custodians/u-boot-dm
convert rockchip to use binman
patman fix for checkpatch
binman optional entries, improved support for ELF symbols
trace improvements
minor fdt refactoring
Update the zstd implementation to match Linux zstd 1.5.2 from commit
2aa14b1ab2.
This was motivated by running into decompression corruption issues when
trying to uncompress files compressed with newer versions of zstd. zstd
users also claim significantly improved decompression times with newer
zstd versions which is a side benefit.
Original zstd code was copied from Linux commit 2aa14b1ab2 which is a
custom-built implementation based on zstd 1.3.1. Linux switched to an
implementation that is a copy of the upstream zstd code in Linux commit
e0c1b49f5b, this results in a large code diff. However this should make
future updates easier along with other benefits[1].
This commit is a straight mirror of the Linux zstd code, except to:
- update a few #include that do not translate cleanly
- linux/swab.h -> asm/byteorder.h
- linux/limits.h -> linux/kernel.h
- linux/module.h -> linux/compat.h
- remove assert() from debug.h so it doesn't conflict with u-boot's
assert()
- strip out the compressor code as was done in the previous u-boot zstd
- update existing zstd users to the new Linux zstd API
- change the #define for MEM_STATIC to use INLINE_KEYWORD for codesize
- add a new KConfig option that sets zstd build options to minify code
based on zstd's ZSTD_LIB_MINIFY[2].
These changes were tested by booting a zstd 1.5.2 compressed kernel inside a
FIT. And the squashfs changes by loading a file from zstd compressed squashfs
with sqfsload. buildman was used to compile test other boards and check for
binary bloat, as follows:
> $ buildman -b zstd2 --boards dh_imx6,m53menlo,mvebu_espressobin-88f3720,sandbox,sandbox64,stm32mp15_dhcom_basic,stm32mp15_dhcor_basic,turris_mox,turris_omnia -sS
> Summary of 6 commits for 9 boards (8 threads, 1 job per thread)
> 01: Merge branch '2023-01-10-platform-updates'
> arm: w+ m53menlo dh_imx6
> 02: lib: zstd: update to latest Linux zstd 1.5.2
> aarch64: (for 2/2 boards) all -3186.0 rodata +920.0 text -4106.0
> arm: (for 5/5 boards) all +1254.4 rodata +940.0 text +314.4
> sandbox: (for 2/2 boards) all -4452.0 data -16.0 rodata +640.0 text -5076.0
[1] e0c1b49f5b
[2] f302ad8811/lib/libzstd.mk (L31)
Signed-off-by: Brandon Maier <brandon.maier@collins.com>
[trini: Set ret to -EINVAL for the error of "failed to detect
compressed" to fix warning, drop ZSTD_SRCSIZEHINT_MAX for non-Linux host
tool builds]
Signed-off-by: Tom Rini <trini@konsulko.com>
The fdt_path_offset() function is slow since it must scan the tree.
This substantial overhead now applies to all boards.
The original code may not be ideal but it is fit for purpose and is only
needed on a few boards.
Reverting this reduces time to set up driver model by about 30ms.
Before revert:
Accumulated time:
47,170 dm_r
53,237 dm_spl
572,986 dm_f
Accumulated time:
44,598 dm_r
50,347 dm_spl
549,133 dm_f
This reverts commit 26f981f295.
Signed-off-by: Simon Glass <sjg@chromium.org>
Some platforms cannot honour this and don't need trace before relocation.
Use 'imply' instead, so boards can disable this.
Signed-off-by: Simon Glass <sjg@chromium.org>
This can be written before relocation. Move it to the data section, since
accessing BSS before relocation is not permitted.
Signed-off-by: Simon Glass <sjg@chromium.org>
If the FDT overlaps with the data region of the image, or with the stack,
it can become corrupted before relocation. Add a check for this, behind a
debug flag, as it can be very confusing and time-consuming to debug.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function uses gd->fdt_blob a lot and cannot be used to check any
other device tree. Use a parameter instead.
Signed-off-by: Simon Glass <sjg@chromium.org>
This function is a bit messy with several #ifdefs. Convert them to use C
for the conditions.
Rewrite the function comment since most of it is stale.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current approach is a bit of a hack and only works for the tpm
subsystem. Add a Kconfig so that crc8 can be enabled in SPL for other
purposes.
Signed-off-by: Simon Glass <sjg@chromium.org>
The event framework is just that, a framework. Enabling it by itself
does nothing, so we shouldn't ask the user about it. Reword (and correct
typos) around this the option and help text. This also applies to
DM_EVENT and EVENT_DYNAMIC. Only EVENT_DEBUG and CMD_EVENT should be
visible to the user to select, when EVENT is selected.
With this, it's time to address the larger problems. When functionality
uses events, typically via EVENT_SPY, the appropriate framework then
must be select'd and NOT imply'd. As the functionality will cease to
work (and so, platforms will fail to boot) this is non-optional and
where select is appropriate. Audit the current users of EVENT_SPY to
have a more fine-grained approach to select'ing the framework where
used. Also ensure the current users of event_register and also select
EVENT_DYNAMIC.
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reported-by: Oliver Graute <Oliver.Graute@kococonnector.com>
Reported-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Fixes: 7fe32b3442 ("event: Convert arch_cpu_init_dm() to use events")
Fixes: 42fdcebf85 ("event: Convert misc_init_f() to use events")
Fixes: c5ef202557 ("dm: fix DM_EVENT dependencies")
Signed-off-by: Tom Rini <trini@konsulko.com>
Tested-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Key data is never written so the parameter can be const, which allows
putting fixed keys in .rodata.
Signed-off-by: John Keeping <john@metanate.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@vrull.eu>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
In efi_disk_add_dev() we have to open protocols with BY_DRIVER and
BY_CHILD_CONTROLLER. Provide the handle of the EFI block driver. The actual
usage of the value will follow in a later patch.
Change function descriptions to Sphinx style.
Remove a TODO: tag.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add a test for the case when the HII database protocol
set_keyboard_layout() function is called with a NULL key_guid argument.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
As per the EFI specification, the HII database protocol function
set_keyboard_layout() must return EFI_INVALID_PARAMETER when it is called
with a NULL key_guid argument. Modify the function accordingly to improve
conformance.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
After calling EFI_ENTRY we have to call EFI_EXIT before returning.
Add a missing EFI_EXIT().
Fixes: 1ccf87165e ("efi_loader: Enable RISCV_EFI_BOOT_PROTOCOL support")
Reported-by: Dave Jones <dave.jones@canonical.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Sunil V L <sunilvl@ventanamicro.com>
This reverts commit 65ba7add0d.
A weak extern is a nasty sight to behold: If the symbol is never
defined, on ARM, the linker will replace the function call with a NOP.
This behavior isn't well documented but there are at least some hints
to it [1].
When timer_read_counter() is not defined, this obviously does the wrong
thing here and it does so silently. The consequence is that a board
without timer_read_counter() will sleep for random amounts and generally
have erratic get_ticks() values.
Drop the __weak annotation of the extern so a linker error is raised
when timer_read_counter() is not defined. This is okay, the original
reason for the reverted change - breaking the sandbox build - no longer
applies.
Final sidenote: This was the only weak extern in the entire tree at
this time as far as I can tell. I guess we should avoid introduction of
them again as they are obviously a very big footgun.
[1]: https://stackoverflow.com/questions/31203402/gcc-behavior-for-unresolved-weak-functions
Fixes: 65ba7add0d ("time: add weak annotation to timer_read_counter declaration")
Reported-by: Serge Bazanski <q3k@q3k.org>
Signed-off-by: Harald Seiler <hws@denx.de>
add initialization of variable 'node',this can aviod the building
warning:
'node' may be used uninitialized [-Wmaybe-uninitialized]
Signed-off-by: Haijun Qin <qinhaijun@eswincomputing.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The fields ConsoleInHandle, ConsoleOutHandle, ConsoleErrHandle must point
to the handles with the respective console protocols. Failure to do so
leads to an error in the EFI Shell:
No SimpleTextInputEx was found. CTRL-based features are not usable.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Up to now we only compared the first letter of the capsule name to sort
them alphabetically. Properly sort by the Unicode alphabet.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When the efi subsystem starts we restore variables that are both in a
file or stored into the .efi_runtime section of U-Boot. However once
a variable gets created or changed the preseeded entries will end up in
the file. As a consequence on the next boot we will end up adding
identical variable entries twice.
Fix this by checking if the to be inserted variable already exists.
Also swap the restoration order and start with the file instead of the
builtin variables, so a user can replace the preseeded ones if needed.
Tested-by: Leo Yan <leo.yan@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
It is volatile variables that we do not allow to be restored from file.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
When the HII protocol function get_package_list_handle() is called with an
invalid package list handle, it returns EFI_NOT_FOUND but this is not in
its list of possible status codes as per the EFI specification.
Return EFI_INVALID_PARAMETER instead to fix conformance.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
While we do not want to use CONFIG_RSA_VERIFY_WITH_PKEY on the host, we
cannot undef the symbol in this manner. As this ends up being a test
within another function we can use !tools_build() as a test here.
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Cc: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Test that GetNextVariableName() checks the parameters.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The VariableNameSize parameter is in bytes but u16_strnlen() counts u16.
Fix the parameter check for null termination.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
To retrieve the EFI variable name by efi_get_next_variable_name_int(),
the sequence of alloc -> efi_get_next_variable_name_int ->
realloc -> efi_get_next_variable_name_int is required.
In current code, this sequence repeatedly appears in
the several functions. It should be curved out a common function.
This commit also fixes the missing free() of var_name16
in eficonfig_delete_invalid_boot_option().
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The EFI Conformance Profile Table entry for EBBR appears in v2.1.0 of the
EBBR specification[1]. Update naming accordingly.
While at it, update the EBBR version referenced in the documentation.
[1]: https://github.com/ARM-software/ebbr/releases/tag/v2.1.0
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We add RISC-V semihosting based serial console for JTAG based early
debugging.
The RISC-V semihosting specification is available at:
https://github.com/riscv/riscv-semihosting-spec/blob/main/riscv-semihosting-spec.adoc
Signed-off-by: Anup Patel <apatel@ventanamicro.com>
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
We factor out the arch-independent parts of the ARM semihosting
implementation as a common library so that it can be shared
with RISC-V.
Signed-off-by: Kautuk Consul <kconsul@ventanamicro.com>
Reviewed-by: Leo Yu-Chi Liang <ycliang@andestech.com>
The rest of the unmigrated CONFIG symbols in the CONFIG_SYS namespace do
not easily transition to Kconfig. In many cases they likely should come
from the device tree instead. Move these out of CONFIG namespace and in
to CFG namespace.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This converts the following to Kconfig:
CONFIG_SYS_TIMER_COUNTS_DOWN
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the possibility to recognize IPv6 address in print function.
To output IPv6 address use %pI6 specifier.
Series-changes: 3
- Substituted #if (...) for if (...) to get better readability
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This functions is used as a converter from IPv6 address string notation
to struct ip6_addr that is used everywhere in IPv6 implementation. For
example it is used to parse and convert IPv6 address from tftpboot
command. Conversion algorithm uses two passes, first to verify syntax and
locate colons and second pass to read the address. In case of valid IPv6
address it returns 0.
Examples of valid strings:
2001:db8::0:1234:1
2001:0db8:0000:0000:0000:0000:1234:0001
::1
::ffff:192.168.1.1
Examples of invalid strings
2001:db8::0::0 (:: can only appear once)
2001:db8:192.168.1.1::1 (v4 part can only appear at the end)
192.168.1.1 (we don't implicity map v4)
Series-changes: 3
- Added function description
- Added length parameter to string_to_ip6()
Series-changes: 4
- Fixed function description style
Signed-off-by: Viacheslav Mitrofanov <v.v.mitrofanov@yadro.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Some commands need to enumerate the existing UEFI load
option variable("Boot####"). This commit transfers some code
from cmd/efidebug.c to lib/efi_loder/, then exposes
efi_varname_is_load_option() function to check whether
the UEFI variable name is "Boot####".
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
EFI_LOADER_DATA/CODE is reserved for EFI applications.
Memory allocated by U-Boot for internal usage should be
EFI_BOOT_SERVICES_DATA or _CODE or EFI_RUNTIME_SERVICES_DATA or _CODE.
Reported-by: François-Frédéric Ozog <ff@ozog.com>
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: François-Frédéric Ozog <ff@ozog.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The dhcp command may be executed after the first UEFI command.
We should still update the EFI_PXE_BASE_CODE_PROTOCOL.
Don't leak content of prior acknowledge packages.
Handle failing allocation when calling malloc().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Provide an EFI binary that prints the boot hart ID as found in the
device-tree as /chosen/boot-hartid property and as provided by the
RISCV_EFI_BOOT_PROTOCOL.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Use unsigned char for the parameter of efi_st_strcmp_16_8. This allows
comparing characters 0x80 - 0xff.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If the array index 'i' < 128, the 'codepage' array is accessed using
[-128...-1] in efi_unicode_collation.c:262. This can lead to a buffer
overflow.
Negative index in efi_unicode_collation.c:262.
The index of the 'codepage' array should be c - 0x80 instead of i - 0x80.
Fixes: 0bc4b0da7b ("efi_loader: EFI_UNICODE_COLLATION_PROTOCOL")
Signed-off-by: Mikhail Ilin <ilin.mikhail.ol@gmail.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Heinrich reports that on RISC-V unaligned access is emulated by OpenSBI
which is very slow. Performance wise it's better if we skip the calls
to u16_strdup() -- which in turn calls u16_strsize() and just allocate/copy the
memory directly. The access to dp.length may still be unaligned, but that's
way less than what u16_strsize() would do
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Use malloc() instead of calloc().
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Closing the files uses the EFI protocol and specifically it's .close
callback. This needs to be wrapped on an EFI_CALL()
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
UEFI specification requires pointers that are passed to protocol member
functions to be aligned. There's a u16_strdup in that function which
doesn't make sense otherwise Add a comment so no one removes it
accidentally
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide a description of the function's logic.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
If the va_list we got handed over contains no protocols we must return
EFI_SUCCESS. However in that case the current code just returns
an unintialized value.
Fix that by setting the return value in the variable definition
Addresses-Coverity: CID 376195: ("Uninitialized variables (UNINIT)")
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Update the sandbox implementation to use UCLASS_HOST and adjust all
the pieces to continue to work:
- Update the 'host' command to use the new API
- Replace various uses of UCLASS_ROOT with UCLASS_HOST
- Disable test_eficonfig since it doesn't work (this should have a unit
test to allow this to be debugged)
- Update the blk test to use the new API
- Drop the old header file
Unfortunately it does not seem to be possible to split this change up
further.
Signed-off-by: Simon Glass <sjg@chromium.org>
AllocatePages() can be called with Type=AllocateAddress. Such a call can
only succeed if *Memory points to the address of an unallocated page range.
A call with *Memory being an address that is not page aligned must not
succeed. The UEFI specification requires returning EFI_OUT_OF_RESOURCES
if the requested pages cannot be allocated.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Variable efi_system_partition holds the efi_system_partition. Currently it
is initialized as:
{
.uclass_id = 0 = UCLASS_ROOT,
.denum = 0,
.part = 0,
}
This indicates that host 0:0 is the efi_system_partition and we see output
like:
=> bootefi hello
** Bad device specification host 0 **
Couldn't find partition host 0:0
To identify that no EFI system partition has been set use UCLASS_INVALID.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Since the commit a9bf024b29 ("efi_loader: disk: a helper function to
create efi_disk objects from udevice"), CONFIG_EFI_SETUP_EARLY option is
by default on and will never be turned off.
So just remove this option.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
CONFIG_NET does not imply that there are actually network devices
available, only CONFIG_NETDEVICES does. Changing to this dependency
obsoletes the check in Kconfig because NETDEVICES means DM_ETH.
Fixes: 0efe1bcf5c ("efi_loader: Add network access support")
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add test cases for accessing the FWU Metadata on the sandbox
platform. The sandbox platform also uses the metadata access driver
for GPT partitioned block devices.
The FWU feature will be tested on the sandbox64 variant with a raw
capsule. Remove the FIT capsule testing from sandbox64 defconfig --
the FIT capsule test will be run on the sandbox_flattree variant.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The FWU Multi Bank Update feature supports updating firmware images
to one of multiple sets(also called banks) of images. The firmware
images are clubbed together in banks, with the system booting images
from the active bank. Information on the images such as which bank
they belong to is stored as part of the metadata structure, which is
stored on the same storage media as the firmware images on a dedicated
partition.
At the time of update, the metadata is read to identify the bank to
which the images need to be flashed(update bank). On a successful
update, the metadata is modified to set the updated bank as active
bank to subsequently boot from.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The FWU Multi Bank Update specification requires the Update Agent to
carry out certain checks at the time of platform boot. The Update
Agent is the component which is responsible for updating the firmware
components and maintaining and keeping the metadata in sync.
The spec requires that the Update Agent perform the following checks
at the time of boot
* Sanity check of both the metadata copies maintained by the platform.
* Get the boot index passed to U-Boot by the prior stage bootloader
and use this value for metadata bookkeeping.
* Check if the system is booting in Trial State. If the system boots
in the Trial State for more than a specified number of boot counts,
change the Active Bank to be booting the platform from.
Call these checks through the main loop event at the time of platform
boot.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add weak functions for getting the update index value and dfu
alternate number needed for FWU Multi Bank update
functionality.
The current implementation for getting the update index value is for
platforms with 2 banks. If a platform supports more than 2 banks, it
can implement it's own function. The function to get the dfu alternate
number has been added for platforms with GPT partitioned storage
devices. Platforms with other storage partition scheme need to
implement their own function.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Acked-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In the FWU Multi Bank Update feature, the information about the
updatable images is stored as part of the metadata, which is stored on
a dedicated partition. Add the metadata structure, and a driver model
uclass which provides functions to access the metadata. These are
generic API's, and implementations can be added based on parameters
like how the metadata partition is accessed and what type of storage
device houses the metadata.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Use the uclass type as the first part of the function name, to be
consistent with the methods in other block drivers.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current name is inconsistent with SPL which uses CONFIG_SPL_TEXT_BASE
and this makes it imposible to use CONFIG_VAL().
Rename it to resolve this problem.
Signed-off-by: Simon Glass <sjg@chromium.org>
This relies on the old LCD implementation which is to be removed. Drop the
existing #ifdef and convert it to C code.
Signed-off-by: Simon Glass <sjg@chromium.org>
There are two problems with both strcmp and strncmp:
(1) The C standard is clear that the contents should be compared as
"unsigned char":
The sign of a nonzero value returned by the comparison functions
memcmp, strcmp, and strncmp is determined by the sign of the
difference between the values of the first pair of characters (both
interpreted as unsigned char) that differ in the objects being
compared.
(2) The difference between two char (or unsigned char) values can
range from -255 to +255; so that's (due to integer promotion) the
range of values we could get in the *cs-*ct expressions, but when that
is then shoe-horned into an 8-bit quantity the sign may of course
change.
The impact is somewhat limited by the way these functions
are used in practice:
- Most of the time, one is only interested in equality (or for
strncmp, "starts with"), and the existing functions do correctly
return 0 if and only if the strings are equal [for strncmp, up to
the given bound].
- Also most of the time, the strings being compared only consist of
ASCII characters, i.e. have values in the range [0, 127], and in
that case it doesn't matter if they are interpreted as signed or
unsigned char, and the possible difference range is bounded to
[-127, 127] which does fit the signed char.
For size, one could implement strcmp() in terms of strncmp() - just
make it "return strncmp(a, b, (size_t)-1);". However, performance of
strcmp() does matter somewhat, since it is used all over when parsing
and matching DT nodes and properties, so let's find some other place
to save those ~30 bytes.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
There is a number of users that use uclass_first_device to access the
first and (assumed) only device in uclass.
Some check the return value of uclass_first_device and also that a
device was returned which is exactly what uclass_first_device_err does.
Some are not checking that a device was returned and can potentially
crash if no device exists in the uclass. Finally there is one that
returns NULL on error either way.
Convert all of these to use uclass_first_device_err instead, the return
value will be removed from uclass_first_device in a later patch.
Signed-off-by: Michal Suchanek <msuchanek@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Loadfile2 code is installing two protocols on it's own handle
and uses efi_delete_handle() to clean it up on failure(s). However
commit 05c4c9e21a ("efi_loader: define internal implementations of
install/uninstallmultiple") prepares the ground for us to clean up
efi_delete_handle() used in favor of Install/UninstallMultipleProtocol.
While at it clean up the non needed void casts to (void *) on the
protolcol installation.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The option SHA256_ALGO does not exist. Remove selecting it.
Fixes: 26dd993657 ("lib: add crypt subsystem")
Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@foundries.io>
Make it clearer why InstallMultipleProtocolInterfaces is invoked with two
NULLs:
* rename guid to esp_guid
* put protocol GUIDs and the related interfaces on same lines
* add comment
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
* Replace the OpenProtocol() call by efi_search_protocol().
* Remove the CloseProtocol() call.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Avoid EFI_CALL() by using efi_close_protocol().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Allow avoiding using EFI_CALL() when closing a protocol by providing an
internal function.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The CloseProtocol() boot service requires a handle as first argument.
Passing the protocol interface is incorrect.
CloseProtocol() only has an effect if called with a non-zero value for
agent_handle. HandleProtocol() uses an opaque agent_handle when invoking
OpenProtocol() (currently NULL). Therefore HandleProtocol() should be
avoided.
* Replace the LocateHandle() call by efi_search_protocol().
* Remove the CloseProtocol() call.
Fixes: 8d99026f06 ("efi_loader: capsule: support firmware update")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The CloseProtocol() boot service requires a handle as first argument.
Passing the protocol interface is incorrect.
CloseProtocol() only has an effect if called with a non-zero value for
agent_handle. HandleProtocol() uses an opaque agent_handle when invoking
OpenProtocol() (currently NULL). Therefore HandleProtocol() should be
avoided.
* Replace the LocateHandle() call by efi_search_protocol().
* Remove the CloseProtocol() call.
* Remove a superfluous goto.
Fixes: ce3dbc5d08 ("efi_loader: add UEFI GPT measurement")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We must always call EFI_EXIT() when returning from an EFIAPI function.
Fixes: 05ef48a248 ("efi_driver: EFI block driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
part is unsigned. So it must be printed with %u.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
A following patch is cleaning up the core EFI code trying to remove
sequences of efi_create_handle, efi_add_protocol.
Although this works fine there's a problem with the latter since it is
usually combined with efi_delete_handle() which blindly removes all
protocols on a handle and deletes the handle. We should try to adhere to
the EFI spec which only deletes a handle if the last instance of a protocol
has been removed. Another problem is that efi_delete_handle() never checks
for opened protocols, but the EFI spec defines that the caller is
responsible for ensuring that there are no references to a protocol
interface that is going to be removed.
So let's fix this by replacing all callsites of
efi_create_handle(), efi_add_protocol() , efi_delete_handle() with
Install/UninstallMultipleProtocol.
In order to do that redefine functions that can be used by the U-Boot
proper internally and add '_ext' variants that will be used from the
EFI API
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move the registration of events for the addition and removal of block
devices to the block device driver. Here we can add a reference to the
EFI Driver Binding protocol as context.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
A function event_notify() exists. We should not use the same name for and
EFI event. Rename events in unit tests.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For handling added and removed block devices we need to register events
which has to be done when the driver is installed.
This patch only creates an empty init function that will be filled with
code later on. The function needs to be called before any EFI block devices
are used. Move the efi_driver_init() call to early init.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
DisconnectController() is based on the open protocol information created
when the driver opens a protocol with BY_CHILD_CONTROLLER or BY_DRIVER.
To create an open protocol information it is required to supply the handle
of the driver as agent handle. This information is available as field
DriverBindingHandle in the driver binding protocol.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
* Carve out function efi_bl_create_block_device() from efi_bl_bind().
* Add a check for U-Boot devices to efi_bl_bind().
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
If creating the block device fails,
* delete all created objects and references
* close the protocol interface on the controller
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When deleting a device or a handle we must remove the link between the two
to avoid dangling references.
Provide function efi_unlink_dev() for this purpose.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
dp_alloc() may return NULL. This needs to be caught.
Fixes: 98d48bdf41 ("efi_loader: provide a function to create a partition node")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
At present there is only one device tree used by the ofnode functions,
except for some esoteric use of live tree. In preparation for supporting
more than one, add a way to reset the list of device trees.
For now this does nothing.
Signed-off-by: Simon Glass <sjg@chromium.org>
An upcoming patch set creates a global function flush(). To make debugging
easier we should not use the same name for a static function.
Rename static functions in the LoadImage() unit test adding an efi_st_
prefix.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The current implementation creates a 'name' value for every node. This
is not needed for the latest device tree format, which includes a name in
the node header.
Adjust the code to point the name at the node header instead.
Also simplify ofnode_get_name(), now that we can rely on it to set the
name correctly. Update the comment to make it clear what name the root
node has.
Signed-off-by: Simon Glass <sjg@chromium.org>
An upcoming patch set creates a global function flush(). To make debugging
easier we should not use the same name for a static function.
Rename static functions in the LoadImage() unit test adding an efi_st_
prefix.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Function print_size() round size to the nearst value with one decimal
fraction number. But in special cases also unit order may overflow.
For example value 1073689396 is printed as "1024 MiB" and value 1073741824
as "1 GiB".
Fix this issue by detecting order overflow and increasing unit order.
With this change also value 1073689396 is printed as "1 GiB".
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Globally replace all occurances of WATCHDOG_RESET() with schedule(),
which handles the HW_WATCHDOG functionality and the cyclic
infrastructure.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Tom Rini <trini@konsulko.com> [am335x_evm, mx6cuboxi, rpi_3,dra7xx_evm, pine64_plus, am65x_evm, j721e_evm]
We currently have an if_type (interface type) and a uclass id. These are
closely related and we don't need to have both.
Drop the if_type values and use the uclass ones instead.
Maintain the existing, subtle, one-way conversion between UCLASS_USB and
UCLASS_MASS_STORAGE for now, and add a comment.
Signed-off-by: Simon Glass <sjg@chromium.org>
efi_set_blk_dev_to_system_partition() assumes that 0 is an invalid
if_type. This is true now but is about to be false. Fix this bug to avoid
a test failure.
Signed-off-by: Simon Glass <sjg@chromium.org>
Selecting this option can be handled in the Kconfig option itself, as it
is with BLK. Update this an drop the various 'select' clauses.
Signed-off-by: Simon Glass <sjg@chromium.org>
This option is fact really related to SPL. For U-Boot proper we always use
driver model for block devices, so CONFIG_BLK is enabled if block devices
are in use.
It is only for SPL that we have two cases:
- SPL_BLK is enabled, in which case we use driver model and blk-uclass.c
- SPL_BLK is not enabled, in which case (if we need block devices) we must
use blk_legacy.c
Rename the symbol to SPL_LEGACY_BLOCK to make this clear. This is
different enough from BLK and SPL_BLK that there should be no confusion.
Signed-off-by: Simon Glass <sjg@chromium.org>
Check the that the hash length is shorter than the message length. This
avoids:
./tools/../lib/rsa/rsa-verify.c:275:11: warning:
‘*db’ may be used uninitialized [-Wmaybe-uninitialized]
275 | db[0] &= 0xff >> leftmost_bits;
Fixes: 061daa0b61 ("rsa: add support of padding pss")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
UEFI specification requires booting from removal media using
a architecture-specific default image name such as BOOTAA64.EFI.
This commit adds the removable media entries into bootmenu,
so that user can select the removable media and boot with
default image.
The bootmenu automatically enumerates the possible bootable
media devices supporting EFI_SIMPLE_FILE_SYSTEM_PROTOCOL,
add it as new UEFI boot option(BOOT####) and update BootOrder
variable. This automatically generated UEFI boot option
has the dedicated guid in the optional_data to distinguish it from
the UEFI boot option user adds manually. This optional_data is
removed when the efi bootmgr loads the selected UEFI boot option.
This commit also provides the BOOT#### variable maintenance feature.
Depending on the system hardware setup, some devices
may not exist at a later system boot, so bootmenu checks the
available device in each bootmenu invocation and automatically
removes the BOOT#### variable corrensponding to the non-existent
media device.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
This commit add the "eficonfig" command.
The "eficonfig" command implements the menu-driven UEFI boot option
maintenance feature. This commit implements the addition of
new boot option. User can select the block device volume having
efi_simple_file_system_protocol and select the file corresponding
to the Boot#### variable. User can also enter the description and
optional_data of the BOOT#### variable in utf8.
This commit adds "include/efi_config.h", it contains the common
definition to be used from other menus such as UEFI Secure Boot
key management.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
UEFI block devices can either mirror U-Boot's internal devices or be
provided by an EFI application like iPXE.
When ConnectController() is invoked for the EFI_BLOCK_IO_PROTOCOL
interface for such an application provided device we create a virtual
U-Boot block device of type "efi_blk".
Currently we do not call ConnectController() when handles for U-Boot's
internal block devices are created. If an EFI application calls
ConnectController() for a handle relating to an internal block device,
we erroneously create an extra "efi_blk" block device.
E.g. the UEFI shell has a command 'connect -r' which calls
ConnectController() for all handles with device path protocol.
In the Supported() method of our EFI_DRIVER_BINDING_PROTOCOL return
EFI_UNSUPPORTED when dealing with an U-Boot internal device.
Reported-by: Etienne Carriere <etienne.carriere@linaro.org>
Fixes: commit 05ef48a248 ("efi_driver: EFI block driver")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Etienne Carriere <etienne.carriere@linaro.org>
Tested-by: Etienne Carriere <etienne.carriere@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Change efi_delete_handle() to not free EFI handles twice.
This change tries to resolved an issue seen since U-Boot v2022.07
in which ExitBootService() attempts to release some EFI handles twice.
The issue was seen booting a EFI shell that invokes 'connect -r' and
then boots a Linux kernel. Execution of connect command makes EFI
subsystem to bind a block device for each root block devices EFI handles.
However these EFI device handles are already bound to a driver and we
can have 2 registered devices relating to the same EFI handler. On
ExitBootService(), the loop removing the devices makes these EFI handles
to be released twice which corrupts memory.
This patch prevents the memory release operation caused by the issue but
but does not resolve the underlying problem.
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Add log message.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a new unit test to test the integrity of the
EFI Conformance Profile Table.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We can use efi_st_get_config_table() in multiple unit tests.
Export the function.
Export system-table and boot-services.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Add an option to tell the TPM to commit non-volatile data immediately it
is changed, rather than waiting until later. This is needed in some
situations, since if the device reboots it may not write the data.
Add definitions for the rest of the Cr50 commands while we are here.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Add a vendor-specific TPM2 command for this and implement it for Cr50.
Note: This is not part of the TPM spec, but is a Cr50 extension.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The message format is incorrect. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
The offset here is incorrect. Fix it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
This feature is used for measured boot, so we can add a log entry to the
TCPA with some information about where the digest comes from. It is not
currently supported in the TPM drivers, but add it to the API so that
code which expects it can signal its request.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
UEFI specification 2.9A requires to display the EUI-64 "in hexadecimal
format with byte 7 first (i.e., on the left) and byte 0 last".
This is in contrast to what the NVMe specification wants.
But it is what EDK II has been implementing.
Here is an example with the patch applied:
qemu-system-aarch64 -machine virt -cpu cortex-a72 -nographic \
-bios denx/u-boot.bin \
-device nvme,id=nvme1,serial=9ff81223 \
-device nvme-ns,bus=nvme1,drive=nvme1n0,eui64=0x123456789ABCDEF0 \
-drive file=arm64.img,if=none,format=raw,id=nvme1n0
=> nvme scan
=> efidebug devices
Device Path
====================
/VenHw(…)/NVMe(0x1,f0-de-bc-9a-78-56-34-12)
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Display the EBBRv2.0 conformance in the ECPT table.
The EBBRv2.0 conformance profile is set in the ECPT if
CONFIG_EFI_EBBR_2_0_CONFORMANCE=y.
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Add dependencies for CONFIG_EFI_EBBR_2_0_CONFORMANCE.
Enable the setting by default.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The ECPT table will be included in the UEFI specification 2.9+.
The ECPT table was introduced in UEFI following the code-first path. The
acceptance ticket can be viewed at:
https://bugzilla.tianocore.org/show_bug.cgi?id=3591
The Conformance Profiles table is a UEFI configuration table that contains
GUID of the UEFI profiles that the UEFI implementation conforms with.
The ECPT table is created when CONFIG_EFI_ECPT=y.
The config is set by default.
Signed-off-by: Jose Marinho <jose.marinho@arm.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The selftest checking the handling of exceptions in UEFI binaries is using
assembly to provide an undefined instruction. On the sandbox the correct
form of the instruction depends on the host architecture.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
In the extended text input protocol support input of control letters
0x1c - 0x1f.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We cannot expect the buffers passed to the input protocols to be zero
filled. If only modifier keys are pressed, we have to return EFI_NOT_READY
but we still have to fill the key structure.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
We need to support multiple digits in the parts of the UEFI verision
number. E.g.
EFI_SPECIFICATION_VERSION = (123 << 16) | 456
must be printed as
123.45.6
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Only probed block devices are available in the UEFI sub-system. Multiple
block devices may be involved in the boot process. So we have to make sure
that all block devices are probed. Another reason is that we store UEFI
variables on the ESP which may be on any block device.
On the sandbox before the patch:
=> efidebug devices
No EFI system partition
Device Device Path
================ ====================
000000001b027c70 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)
000055d078bc1ae0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Uart(0,0,D,D)
000000001b22e0b0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/MAC(020011223344,1)
After the patch:
=> efidebug devices
No EFI system partition
Device Device Path
================ ====================
000000001b027c70 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)
000055bdac8ddae0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Uart(0,0,D,D)
000000001b230920 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(2)/SD(0)
000000001b233ac0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)
000000001b233b80 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(1,GPT,d0a914ee-a71c-fc1e-73f0-7e302b0e6c20,0x30,0x1)
000000001b234110 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(1)/HD(2,GPT,9330a0ea-8aff-f67a-294c-fa05d60896c3,0x31,0x1)
000000001b22f0e0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(2)
000000001b238df0 /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/MAC(020011223344,1)
Fixes: a9bf024b29 ("efi_loader: disk: a helper function to create efi_disk objects from udevice")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
CONFIG_SYS_TIMER_RATE might be a dynamic value, i.e. a function call
instead of a static value, thus it has to be evaluated at runtime. If it
is a static value, the compiler should be able to optimize the unused
branches out.
This will be needed for kirkwoods dynamic CONFIG_SYS_TCLK setting.
Cc: Pali Rohár <pali@kernel.org>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The field, ifname, in efi_disk_obj is set but never used anywhere.
Just remove it.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This is a preparation patch to provide the unified method
to access udevice pointer associated with the EFI handle
by adding udevice pointer into struct efi_object.
The patch also introduces a helper function efi_link_dev()
to link the udevice and EFI handle.
The EFI handles of both EFI block io driver implemented in
lib/efi_loader/efi_disk.c and EFI block io driver implemented
as EFI payload can access the udevice pointer in the struct efi_object.
We can use this udevice pointer to get the U-Boot friendly
block device name(e.g. mmc 0:1, nvme 0:1) through EFI handle.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Ensure that the string we convert to UTF-16 is NUL terminated even
if the device path only contains end nodes.
Fixes: bd3d75bb0c ("efi_loader: multi part device paths to text")
Addresses-Coverity: 350434 ("Uninitialized scalar variable")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The current way of handling things like EFI bootmgr is a bit odd, since
that bootmeth handles selection of the bootdev itself. VBE needs to work
the same way, so we should support it properly.
Add a flag that indicates that the bootmeth is global, rather than being
invoked on each bootdev. Provide a helper to read a bootflow from the
bootmeth.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present ofnode only works with a single device tree, for the most part.
This is the control FDT used by U-Boot.
When booting an OS we may obtain a different device tree and want to
modify it. Add some initial support for this into the ofnode API.
Note that we don't permit aliases in this other device tree, since the
of_access implementation maintains a list of aliases collected at
start-up. Also, we don't need aliases to do fixups in the other FDT. So
make sure that flat tree and live tree processing are consistent in this
area.
Signed-off-by: Simon Glass <sjg@chromium.org>
We want to use VBE to mean Verfiied Boot for Embedded in U-Boot. Rename
the existing VBE (Vesa BIOS extensions) to allow this.
Verified Boot for Embedded is documented doc/develop/vbe.rst
Signed-off-by: Simon Glass <sjg@chromium.org>
In file included from include/linux/bitops.h:22,
from include/log.h:15,
from include/linux/printk.h:4,
from include/common.h:20,
from lib/lz4_wrapper.c:6:
lib/lz4_wrapper.c: In function ‘ulz4fn’:
include/linux/kernel.h:184:17: warning: comparison of distinct pointer types lacks a cast
(void) (&_min1 == &_min2); \
^~
lib/lz4_wrapper.c:104:18: note: in expansion of macro ‘min’
size_t size = min((ptrdiff_t)block_size, end - out);
^~~
Signed-off-by: Pali Rohár <pali@kernel.org>
This patch is fixing a broken boot observed on stm32mp157c-dk2 board.
IS_ENABLED macro should be used to check if a compilation flag is set
to "y" or "m".
LMB_MEMORY_REGIONS is set to a numerical value, IS_ENABLED macro is not
suitable in this case.
Fixes: 7c1860fce4 ("lmb: Fix lmb property's defination under struct lmb")
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Michal Simek <michal.simek@amd.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The TPM device has a builtin random number generator(RNG)
functionality. Expose the RNG functions of the TPM device to the
driver model so that they can be used by the EFI_RNG_PROTOCOL if the
protocol is installed.
Also change the function arguments and return type of the random
number functions to comply with the driver model api.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Due to U-Boot's lazy binding the RNG presented by the TCG is not available
until the EFI_TCG2 protocol has been initialized. Since the TPM has a
built-in RNG device we can use for the OS randomization, move the RNG
protocol installation after the TCG.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
These functions should really be available outside the TPM code, so that
other callers can find out which version the TPM is. Rename them to have
a tpm_ prefix() and add them to the header file.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
start of test for fdt command
-----BEGIN PGP SIGNATURE-----
iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAmLgRtERHHNqZ0BjaHJv
bWl1bS5vcmcACgkQfxc6PpAIreYXFwgAlALOMj3bwwsIAXNa5j/hPb3j/ecIqXgn
ocyxN+U5eSb2Ju5Jc9QmSeUMnGrii9+PW9j0JApdHrbUgBI2Sx+zwqMTIfA+BS05
4xXZgk5jOT+we2489FjgFcplv+dIuVlsB/Zo6zTbZyjkobfilYsZEGYHJ/CYNaIH
n7EmZeby1cXL7DMCxT39d3hD43XSX8cqQ1IIiF9DgtHQYs2Ff8dFcbWArSdgLX3o
Eob2Qj/GjScg87zjZcsgZajWJMHUfMeD5ZiKN2fR0T/wOdO1WtzFoF2Mt8KZcW1j
BD1shgBCMSSl5EgRG1BQZw4Sa92W2IBlbJ9tfIh8qnWOzEBzOs/M6w==
=lsO4
-----END PGP SIGNATURE-----
Merge tag 'dm-pull-26jul22' of https://gitlab.denx.de/u-boot/custodians/u-boot-dm.git
minor dm- and fdt-related fixes
start of test for fdt command
Update this feature so that it works on sandbox, using a basic identity
mapping. This allows us to run the 'ut addrmap' test.
Also fix up the test to use the correct macros to access the linker
list, so that the 'ut addrmap' command actually works.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit exposes the END device path node.
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tighten up symbol dependencies in a number of places. Ensure that a SPL
specific option has at least a direct dependency on SPL. In places
where it's clear that we depend on something more specific, use that
dependency instead. This means in a very small number of places we can
drop redundant dependencies.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
At the last step of PE image authentication, an image's hash value must be
compared with a message digest stored as the content (of SpcPeImageData type)
of pkcs7's contentInfo.
Fixes: commit 4540dabdca ("efi_loader: image_loader: support image authentication")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This function is used to calculate a message digest as part of
authentication process in a later patch.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
In MS authenticode, pkcs7 should have data in its contentInfo field.
This data is tagged with SpcIndirectData type and, for a signed PE image,
provides a image's message digest as SpcPeImageData.
This parser is used in image authentication to parse the field and
retrieve a message digest.
Imported from linux v5.19-rc, crypto/asymmetric_keys/mscode*.
Checkpatch.pl generates tones of warnings, but those are not fixed
for the sake of maintainability (importing from another source).
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
The requsted partition disk sector incorrectly has the parition start
sector added in twice for UCLASS_PARTITION devices. The efi_disk_rw_blocks()
routine adds the diskobj->offset to the requested lba. When the device
is a UCLASS_PARTITION, the dev_read() or dev_write() routine is called
which adds part-gpt_part_info.start. This causes I/O to the wrong sector.
Takahiro Akashi suggested removing the offset field from the efi_disk_obj
structure since disk-uclass.c handles the partition start biasing. Device
types other than UCLASS_PARTITION set the diskobj->offset field to zero
which makes the field unnecessary. This change removes the offset field
from the structure and removes all references from the code which is
isolated to the lib/efi_loader/efi_disk.c module.
This change also adds a test for the EFI ReadBlocks() API in the EFI
selftest code. There is already a test for reading a FAT file. The new
test uses ReadBlocks() to read the same "disk" block and compare it to
the data read from the file system API.
Signed-Off-by: Paul Barbieri <plb365@gmail.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This converts the following to Kconfig:
CONFIG_ENV_MIN_ENTRIES
CONFIG_ENV_MAX_ENTRIES
Cc: Michal Simek <michal.simek@amd.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Since bb5930d5c9 ("exynos: video: Convert several boards to driver
model for video") there have been no callers of any of the exynos_lcd_*
family of functions. Remove these from the boards, and then remove
unused logo and related code as well.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Minkyu Kang <mk7.kang@samsung.com>
Tighten up symbol dependencies in a number of places. Ensure that a VPL
specific option has at least a direct dependency on VPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Tighten up symbol dependencies in a number of places. Ensure that a TPL
specific option has at least a direct dependency on TPL. In places
where it's clear that we depend on something more specific, use that
dependency instead.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
Mark sha256_process as weak to allow hardware specific implementation.
Add parameter for supporting multiple blocks processing.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Mark sha1_process as weak to allow hardware specific implementation.
Add parameter to support for multiple blocks processing.
Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
cp.b is used a lot as a way to load binaries to memory and execute
them, however we may need to integrate this with the efi subsystem to
set it up as a bootdev.
So, introduce a loadm command that will be consistent with the other
loadX commands and will call the efi API's.
ex: loadm $kernel_addr $kernel_addr_r $kernel_size
with this a kernel with CONFIG_EFI_STUB enabled will be loaded and
then subsequently booted with bootefi command.
Signed-off-by: Rui Miguel Silva <rui.silva@linaro.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
If CONFIG_VIDEO_DM=n we query the display size from the serial console.
Especially when using a remote console the response can be so late that
it interferes with autoboot.
Only query the console size when running an EFI binary.
Add debug output showing the determined console size.
Reported-by: Fabio Estevam <festevam@gmail.com>
Fixes: a57ad20d07 ("efi_loader: split efi_init_obj_list() into two stages")
Fixes: a9bf024b29 ("efi_loader: disk: a helper function to create efi_disk objects from udevice")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Tested-by: Fabio Estevam <festevam@denx.de>
Tested-by: Heiko Thiery <heiko.thiery@gmail.com>
Allow booting from a short form device-path without file path, e.g.
/HD(1,GPT,5ef79931-a1aa-4c70-9d67-611e8f69eafd,0x800,0x1000)
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The GetImageInfo function definitions for the FIT images and raw
images are the same. Use a common function for the both the Firmware
Management Protocol(FMP) instances for raw and FIT images.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The EFI_IGNORE_OSINDICATIONS config symbol was introduced as a
mechanism to have capsule updates work even on platforms where the
SetVariable runtime service was not supported. The current logic
requires the OsIndications variable to have been set to a 64 bit value
even when the EFI_IGNORE_OSINDICATIONS config is enabled. Return an
error code on not being able to read the variable only when
EFI_IGNORE_OSINDICATIONS is not enabled.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Asking if the alias we found actually points at the device tree node
we passed in (in the guise of its offset from blob) can be done simply
by asking if the fdt_path_offset() of the alias' path is identical to
offset.
In fact, the current method suffers from the possibility of false
negatives: dtc does not necessarily emit a phandle property for a node
just because it is referenced in /aliases; it only emits a phandle
property for a node if it is referenced in <angle brackets>
somewhere. So if both the node we passed in and the alias node we're
considering don't have phandles, fdt_get_phandle() returns 0 for both.
Since the proper check is so simple, there's no reason to hide that
behind a config option (and if one really wanted that, it should be
called something else because there's no need to involve phandle in
the check).
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Acked-by: Aswath Govindraju <a-govindraju@ti.com>
While our copy of zlib is missing upstream commit 263b1a05b04e ("Allow
deflatePrime() to insert bits in the middle of a stream.") we do have
Z_FIXED support, and so the majority of the code changes in 5c44459c3b28
("Fix a bug that can crash deflate on some input when using Z_FIXED.")
apply here directly and cleanly. As this has been assigned a CVE, lets
go and apply these changes.
Link: 5c44459c3b
Reported-by: "Gan, Yau Wai" <yau.wai.gan@intel.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Add support for the authentication of UEFI capsules containing FIT images.
The authentication code is moved out of the function handling raw images
into a new function efi_firmware_capsule_authenticate(). The special case
for the FMP header coming from edk2 tools is preserved. There is no
functional change for capsules containing raw images.
The python test for signed capsules with raw images is renamed with no
functional change and a new test is added for signed capsules containing
FIT images.
This can be tested with sandbox64_defconfig or sandbox_flattree_defconfig,
plus CONFIG_EFI_CAPSULE_AUTHENTICATE=y.
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
The GetImageInfo function of the Firmware Mangement Protocol(FMP) gets
called initially to query the size of the image descriptor array that
would have to be allocated. During this call, the rest of the function
arguments, specifically pointers might be passed as NULL. Do not
populate the descriptor_count value before it is known that the call
to GetImageInfo has been made with the allocated buffer for the image
descriptors.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This fixes the following warnings:
./lib/efi_loader/efi_firmware.c:283: warning: Function parameter or member 'package_version' not described in 'efi_firmware_fit_get_image_info'
./lib/efi_loader/efi_firmware.c:283: warning: Function parameter or member 'package_version_name' not described in 'efi_firmware_fit_get_image_info'
./lib/efi_loader/efi_firmware.c:369: warning: bad line: firmware image
./lib/efi_loader/efi_firmware.c:395: warning: Function parameter or member 'package_version' not described in 'efi_firmware_raw_get_image_info'
./lib/efi_loader/efi_firmware.c:395: warning: Function parameter or member 'package_version_name' not described in 'efi_firmware_raw_get_image_info'
Signed-off-by: Vincent Stehlé <vincent.stehle@arm.com>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Booting from a short-form device path which starts with the first element
being a File Path Media Device Path failed because it doesn't contain
any valid device with simple file system protocol and efi_dp_find_obj()
in efi_load_image_from_path() will return NULL.
For instance,
/VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/Scsi(0,0)/\helloworld.efi
-> shortened version: /\helloworld.efi
With this patch applied, all the media devices with simple file system
protocol are enumerated and the boot manager attempts to boot temporarily
generated device paths one-by-one.
This new implementation is still a bit incompatible with the UEFI
specification in terms of:
* not creating real boot options
* not try
"If a device does not support the EFI_SIMPLE_FILE_SYSTEM_PROTOCOL, but
supports the EFI_BLOCK_IO_PROTOCOL protocol, then the EFI Boot Service
ConnectController must be called for this device with DriverImageHandle
and RemainingDevicePath set to NULL and the Recursive flag is set to TRUE."
(See section 3.1.2 "Load Option Processing".)
But it still gives us a closer and better solution than the current.
Fixes: commit 9cdf470274 ("efi_loader: support booting via short-form device-path")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This helper function will be used to determine if the device is
removable media, initially for handling a short-path loading.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently we don't support sha384/512 for the X.509 certificate
in dbx. Moreover if we come across such a hash we skip the check
and approve the image, although the image might needs to be rejected.
Rework the code a bit and fix it by adding an array of structs with the
supported GUIDs, len and literal used in the U-Boot crypto APIs instead
of hardcoding the GUID types.
It's worth noting here that efi_hash_regions() can now be reused from
efi_signature_lookup_digest() and add sha348/512 support there as well
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Fixes
WARNING: unmet direct dependencies detected for EVENT_DYNAMIC
Depends on [n]: EVENT [=n]
Selected by [y]:
- EFI_LOADER [=y] && OF_LIBFDT [=y] && ...
and the succeeding build breakage.
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We currently overflow due to wrong types used internally in rtc_mktime,
on all platforms, and we return a too small type on 32-bit.
One consumer that directly benefits from this is mktime64. Many others
may still store the result in a wrong type.
While at it, drop the redundant cast of mon in rtc_mktime (obsoleted by
714209832d).
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Under the current implementation, booting from removable media using
a architecture-specific default image name, say BOOTAA64.EFI, is
supported only in distro_bootcmd script. See the commit 74522c898b
("efi_loader: Add distro boot script for removable media").
This is, however, half-baked implementation because
1) UEFI specification requires this feature to be implemented as part
of Boot Manager's responsibility:
3 - Boot Manager
3.5.1 Boot via the Simple File Protocol
When booting via the EFI_SIMPLE_FILE_SYSTEM_PROTOCOL, the FilePath will
start with a device path that points to the device that implements the
EFI_SIMPLE_FILE_SYSTEM_PROTOCOL or the EFI_BLOCK_IO_PROTOCOL. The next
part of the FilePath may point to the file name, including
subdirectories, which contain the bootable image. If the file name is
a null device path, the file name must be generated from the rules
defined below.
...
3.5.1.1 Removable Media Boot Behavior
To generate a file name when none is present in the FilePath, the
firmware must append a default file name in the form
\EFI\BOOT\BOOT{machine type short-name}.EFI ...
2) So (1) entails the hehavior that the user's preference of boot media
order should be determined by Boot#### and BootOrder variables.
With this patch, the semantics mentioned above is fully implemented.
For example, if you want to boot the system from USB and SCSI in this
order,
* define Boot0001 which contains only a device path to the USB device
(without any file path/name)
* define Boot0002 which contains only a device path to the SCSI device,
and
* set BootOrder to Boot0001:Boot0002
To avoid build error for sandbox, default file name "BOOTSANDBOX.efi"
is defined even if it is out of scope of UEFI specification.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
On sandbox use binary name corresponding to host architecture.
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
This function will be used in the next commit where some behavior
of EFI boot manager will be expanded.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Provide u16 string version of strlcat().
Signed-off-by: Masahisa Kojima <masahisa.kojima@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
lib/charset.c is not optional for
EFI_APP || EFI_LOADER || UFS || UT_UNICODE.
These must select CONFIG_CHARSET.
Fixes: 726cd9836d ("efi: Make unicode printf available to the app")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The unit test has not been built since CPU_V7 was rename CPU_V7A.
Fixes: acf1500138 ("arm: v7: Kconfig: Rename CPU_V7 as CPU_V7A")
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
When resetting the text console the colors have to be set before clearing
the screen. Otherwise the background color may be wrong.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
While GPT partition is mandated in UEFI specification, CONFIG_PARTITION is
seen optional under the current implementation.
So modify efi_disk_rw_blocks() to allow accepting UCLASS_BLK devices.
Fixes: commit d97e98c887 ("efi_loader: disk: use udevice instead of blk_desc")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
If the path consists only of an end node, it does not refer to a partition.
Avoid returning a random value from the stack in this case.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The log functions print file name, line number, and function name if
selected via the log command or customizing. Don't print the function
name twice.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
As removal of nds32 has been ack'd for the Linux kernel, remove support
here as well.
Cc: Rick Chen <rick@andestech.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Rick Chen <rick@andestech.com>
To quote the author:
The bootflow feature provide a built-in way for U-Boot to automatically
boot an Operating System without custom scripting and other customisation.
This is called 'standard boot' since it provides a standard way for
U-Boot to boot a distro, without scripting.
It introduces the following concepts:
- bootdev - a device which can hold a distro
- bootmeth - a method to scan a bootdev to find bootflows (owned by
U-Boot)
- bootflow - a description of how to boot (owned by the distro)
This series provides an implementation of these, enabled to scan for
bootflows from MMC, USB and Ethernet. It supports the existing distro
boot as well as the EFI loader flow (bootefi/bootmgr). It works
similiarly to the existing script-based approach, but is native to
U-Boot.
With this we can boot on a Raspberry Pi 3 with just one command:
bootflow scan -lb
which means to scan, listing (-l) each bootflow and trying to boot each
one (-b). The final patch shows this.
With a standard way to identify boot devices, booting become easier. It
also should be possible to support U-Boot scripts, for backwards
compatibility only.
...
The design is described in these two documents:
https://drive.google.com/file/d/1ggW0KJpUOR__vBkj3l61L2dav4ZkNC12/view?usp=sharinghttps://drive.google.com/file/d/1kTrflO9vvGlKp-ZH_jlgb9TY3WYG6FF9/view?usp=sharing
At present it is not possible to find out which part of the string is the
number part and which is before it. Add a new variant which provides this
feature, so we can separate the two in the caller.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present this has a minor bug in that it reads the byte before the
start of the string, if it is empty. Also it doesn't handle a
non-numeric prefix which is only one character long.
Fix these bugs with a reworked implementation. Add a test for the second
case. The first one is hard to test.
Signed-off-by: Simon Glass <sjg@chromium.org>
Documentation:
* Document image size parameter of bootefi command
UEFI:
* avoid building partition support in SPL/TPL where not required
* improve integration of EFI subsystem and driver model
* restore ability to boot arbitrary blob
-----BEGIN PGP SIGNATURE-----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=a5qc
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc1-3' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc1-3
Documentation:
* Document image size parameter of bootefi command
UEFI:
* avoid building partition support in SPL/TPL where not required
* improve integration of EFI subsystem and driver model
* restore ability to boot arbitrary blob
In most of all cases, we can avoid using blk_desc which is expected
to be private to udevice(UCLASS_BLK), that is, the data should not
be manipulated outside the device driver unless really needed.
Now efi_disk's internally use dev_read/write() interfaces
if CONFIG_PARTITIONS is enabled.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When we create an efi_disk device with an UEFI application using driver
binding protocol, the 'efi_driver' framework tries to create
a corresponding block device(UCLASS_BLK/IF_TYPE_EFI). This will lead to
calling a PROBE callback, efi_disk_probe().
In this case, however, we don't need to create another "efi_disk" device
as we already have this device instance.
So we should avoid recursively invoke further processing in the callback
function.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This function is expected to be called, in particular from dm's pre_remove
hook, when associated block devices no longer exist.
Add efi_disk_remove() function.
This function removes an efi_disk object for a raw disk device (UCLASS_BLK)
and related objects for its partitions (UCLASS_PARTITION).
So this function is expected to be called through driver model's "remove"
interface every time a raw disk device is to be disconnected.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
When we create an efi_disk device with an UEFI application using driver
binding protocol, the 'efi_driver' framework tries to create
a corresponding block device(UCLASS_BLK/IF_TYPE_EFI). This will lead to
calling a PROBE callback, efi_disk_probe().
In this case, however, we don't need to create another "efi_disk" device
as we already have this device instance.
So we should avoid recursively invoke further processing in the callback
function.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add efi_disk_probe() function.
This function creates an efi_disk object for a raw disk device (UCLASS_BLK)
and additional objects for related partitions (UCLASS_PARTITION).
So this function is expected to be called through driver model's "probe"
interface every time one raw disk device is detected and activated.
We assume that partition devices (UCLASS_PARTITION) have been created
when this function is invoked.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
In the next commit, CONFIG_EFI_SETUP_EARLY will become mandated
in order to support dynamic enumeration of efi_disk objects.
This can, however, be problematic particularly in case of file-based
variable storage (efi_variable.c, default).
Non-volatile variables are to be restored from EFI system partition
by efi_init_variables() in efi_init_obj_list(). When efi_init_obj_list()
is called in board_init_r(), we don't know yet what disk devices
we have since none of device probing commands (say, scsi rescan) has not
been executed at that stage.
So in this commit, a preparatory change is made; efi_init_obj_list() is
broken into the two functions;
* efi_init_early(), and
* new efi_init_obj_list()
Only efi_init_early() will be called in board_init_r(), which allows
us to execute any of device probing commands, either though "preboot"
variable or normal command line, before calling efi_init_obj_list() which
is to be invoked at the first execution of an efi-related command
(or at efi_launch_capsules()) as used to be.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Now we can build efi_loader with block device support (CONFIG_BLK) and
without CONFIG_PARTITIONS.
So change Makefile.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
In the current implementation, partition table support (either GPT or DOS)
is not mandatory. So CONFIG_PARTITION_UUIDS should not be enabled
(selected) unconditionally.
Fixes: commit 17f8cda505 ("efi_loader: set partition GUID in device path for SIG_TYPE_GUID")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Commit 690af71850 changed this condition
from an explicit
IS_ENABLED(CONFIG_SPL_SEPARATE_BSS)
to
CONFIG_IS_ENABLED(SEPARATE_BSS)
The documentation for CONFIG_IS_ENABLED() in include/linux/kconfig.h
implies that we will get the correct behaviour, but the actual behaviour
differs such that this condition is now always false.
This stopped TPL being able to load the device tree blob at least on the
ROCKPro64 board (RK3399 SoC), since the wrong device tree location was
chosen.
The issues causing this behaviour with CONFIG_IS_ENABLED() are:
1. The documentation implies that CONFIG_SPL_BUILD =>
CONFIG_SPL_<option> is considered before the TPL equivalent.
Actually, the TPL options have higher priority - see definition of
_CONFIG_PREFIX.
2. The documentation implies a fallthrough, eg. if CONFIG_SPL_BUILD is
defined but the CONFIG_SPL_<option> is not, then it will proceed to
check if CONFIG_TPL_BUILD
Actually, if CONFIG_TPL_BUILD is defined, then it stops there
and CONFIG_SPL_BUILD is not considered - see definition of
_CONFIG_PREFIX.
During TPL build, at least for the ROCKPro64, both CONFIG_TPL_BUILD
and CONFIG_SPL_BUILD are defined, but because of the above, only TPL
options are considered. Since there is no CONFIG_TPL_SEPARATE_BSS,
this fails.
Fixes: 690af71850 ("fdt: Correct condition for SEPARATE_BSS")
Signed-off-by: Andrew Abbott <andrew@mirx.dev>
U-Boot CRC-16 implementation uses polynomial x^16 + x^12 + x^5 + 1 which is
not standard CRC-16 algorithm, but it is known as CRC-16-CCITT. Rename file
crc16.c to crc16-ccitt.c to reduce confusion.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The capsule update code has been modified for getting the image GUID
values from the platform code. With this, each image now has a unique
GUID value. With this change, there is no longer a need for defining
GUIDs for FIT and raw images. Remove these GUID values.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Currently, there are a bunch of boards which enable the UEFI capsule
update feature. The actual update of the firmware images is done
through the dfu framework which uses the dfu_alt_info environment
variable for getting information on the update, like device, partition
number/address etc. The dfu framework allows the variable to be set
through the set_dfu_alt_info function defined by the platform, or if
the function is not defined, it gets the variable from the
environment. Using the value set in the environment is not very
robust, since the variable can be modified from the u-boot command
line and this can cause an incorrect update.
To prevent this from happening, define the set_dfu_alt_info function
when the capsule update feature is enabled. A weak function is defined
which sets the dfu_alt_info environment variable by getting the string
for the variable from the platform.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
The current capsule update code compares the image GUID value in the
capsule header with the image GUID value obtained from the
GetImageInfo function of the Firmware Management Protocol(FMP). This
comparison is done to ascertain if the FMP's SetImage function can be
called for the update. Make this checking more robust by comparing the
image_index value passed through the capsule with that returned by the
FMP's GetImageInfo function. This protects against the scenario of the
firmware being updated in a wrong partition/location on the storage
device if an incorrect value has been passed through the capsule,
since the image_index is used to determine the location of the update
on the storage device.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Currently, the image descriptor array that has been passed to the
GetImageInfo function of the Firmware Management Protocol(FMP) gets
populated through the data stored with the dfu framework. The
dfu data is not restricted to contain information only of the images
updatable through the capsule update mechanism, but it also contains
information on other images. The image descriptor array is also parsed
by the ESRT generation code, and thus the ESRT table contains entries
for other images that are not being handled by the FMP for the capsule
updates. Fix this by populating the image descriptor array from the
structure initialised in the board file.
The other issue fixed is assignment of a separate GUID for all images
in the image descriptor array. The UEFI specification mandates that
all entries in the ESRT table should have a unique GUID value as part
of the FwClass member of the EFI_SYSTEM_RESOURCE_ENTRY. Currently, all
images are assigned a single GUID value, either an FIT GUID or a raw
image GUID. This is fixed by obtaining the GUID values from the
efi_fw_images array defined per platform.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Set digest_size SHA384 and SHA512 algorithms in pkcs7 and x509,
(not set by ported linux code, but needed by __UBOOT__ part).
EFI_CAPSULE_AUTHENTICATE doesn't select these algos but required for
correctness if certificates contain sha384WithRSAEncryption or
sha512WithRSAEncryption OIDs.
Signed-off-by: Dhananjay Phadke <dphadke@linux.microsoft.com>
Reviewed-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Modify function to support any salt length instead of max
length only. Function now detects salt length by parsing
the content of db buffer. Note that it works with (but is
not limited to) zero-length, digest-length and max-length
Signed-off-by: SESA644425 <gioja.hermann@non.se.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prior to introduction of modifications in rsassa_pss functions
related to padding verification, doing a pass to reduce memory
consumption of function by replacing memory copies of parts of
const buffer by pointers to the original buffer (masked_db and
h are subparts of msg buffer which is declared const, salt is a
subpart of db which is a working buffer, unmodified after being
filled). New pointers scope is limited to the function where
they are declared (not returned to caller by any mean), zeroing
risk of memory fault related to the change.
Signed-off-by: SESA644425 <gioja.hermann@non.se.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Prior to introduction of modifications in rsassa_pss functions
related to padding verification, doing a pass to update
const-correctness in targeted functions to comply with
coding-rules and avoid const-cast
Signed-off-by: SESA644425 <gioja.hermann@non.se.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Use sysreset_walk_halt() directly from reset-after-capsule-on-disk
feature to reboot (cold reset) machine instead of using reset command
interface, since this is not a command.
Note that this will make CONFIG_EFI_CAPSULE_ON_DISK depending on
the CONFIG_SYSRESET.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Make efi_load_capsule_drivers() available even if EFI_CAPSULE_ON_DISK
is disabled because the caller (efi_init_obj_list()) expects it only
relays on EFI_HAVE_CAPSULE_SUPPORT.
Suggested-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu@linaro.org>
Since be66b89da3 ("efi_loader: configuration of variables store")
the choice of EFI_VARIABLE_FILE_STORE or EFI_MM_COMM_TEE
is mutually-exclusive, however efi_var_to_file also allows
for "neither". Provide an additional Kconfig option.
Signed-off-by: Tom Saeger <tom.saeger@oracle.com>
Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
We don't use an appended tree for sandbox and the required symbols are
not present. Add a condition to avoid a build error.
Signed-off-by: Simon Glass <sjg@chromium.org>
If the buffer is empty and not allocated, then abuf_realloc() tries to
copy invalid data. This happens because an incorrect change to use
memdup() was added after the original code was written.
Signed-off-by: Simon Glass <sjg@chromium.org>
This commit adds the option SPL_RSA_VERIFY_WITH_PKEY.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
This commit adds the options:
- SPL_ASYMMETRIC_KEY_TYPE
- SPL_ASYMMETRIC_PUBLIC_KEY_SUBTYPE
- SPL_RSA_PUBLIC_KEY_PARSER
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
