This patch leaces the cache configuration untouched for the AXP in the
setup done by the BootROM. Resulting in the cache still being enabled
at the startup of U-Boot. This leads to a slightly faster boot to the
U-Boot prompt (or Linux of course).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch removes the call to arch_cpu_init() in the SPL U-Boot version.
As SPL does not need all the configuration done in this function. And
also does not need the reconfiguration of the internal register
address to 0xf1000000. This will be done by the main U-Boot later on.
This also fixes a problem with the timer not beeing initialized on AXP,
as needed for the mdelay in the setup_usb_phys(). This will now only
be called once in main U-Boot.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Add functionality to correctly disable the L2 cache on the Armada XP
and 38x platforms.
Without this, booting into Linux on ClearFog (A38x) results in a hangup
without any output on the serial console at all. Even with earlyprintk
enabled.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Until now, the L2 cache was never enabled again in U-Boot. To get
even better performance (bootup time), lets enable the L2 cache
in U-Boot. This code was taken from the Linux kernel.
A performance gain was measured on the DB-MV784MP-GP board by testing
with tftpboot and sata commands.
This patch also cleans up the L2 cache related code. And makes sure that
the L2 cache is only disabled once.
Please note that A38x still runs with L2 cache disabled. And needs
to be enabled for this SoC in a separate patch if needed or desired.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic support for the SolidRun ClearFog Armada 38x based
board to mainline U-Boot. Supported interfaces / devices are:
- DDR3
- UART
- MMC
- Ethernet port 0 (connected to dedicated PHY)
- I2C
The included DT source was taken from Russell King's ftp server:
http://www.home.arm.linux.org.uk/~rmk/clearfog/
With only minor modifications, like the addition of some aliases and the
"u-boot,dm-pre-reloc" property.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Rabeeh Khoury <rabeeh@solid-run.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch moves some config options to the mvebu common include file.
Making it easier to not forget these defines for new boards.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Update this driver to support driver model. As all MVEBU boards using
this driver are converted with this patch, the non-driver-model code
can be removed completely. This is also the reason why this patch
is quite big and includes a) the driver change and b) the
platform change. As its not git-bisect save otherwise.
With this conversion, some parameters are now extracted from the
DT instread of using the config header defines. The supported
properties right now are:
PHY-mode ("phy-mode") and PHY-address ("reg").
The base addresses for the ethernet controllers can be removed from
the header files as well.
Please note that this patch also removes the E1000 network driver
from some MVEBU config headers. This is necessary, as with DM_ETH
configured and the e1000 driver enabled, the PCI driver also needs
to support DM. But the MVEBU PCI(e) driver still needs to get
ported to DM. When this is done, the E1000 driver can be enabled
again.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Simon Glass <sjg@chromium.org>
This patch enables the DM support for the SPI driver and the
SPI NOR flash chips. Some MVEBU boards boot from SPI NOR, so
adding the aliases and enabling CONFIG_DM_SEQ_ALIAS is needed
here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
This patch adds full DM support to the SPL on MVEBU. Currently
only serial is supported. Other drivers will follow.
This patch also adds the necessary config values for the DEBUG UART
to the MVEBU defconfig files. This came in handy while implementing
this DM support.
Additionally, the mvebu specific SPL linker script is removed and
this common one is used instead:
arch/arm/cpu/u-boot-spl.lds
This common linker script already handles all special cases. No need
to reinvent the wheel for MVEBU here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <dirk.eibach@gdsys.cc>
Cc: Simon Glass <sjg@chromium.org>
By using the common timer functions for mvebu/kirkwood we can get rid of quite
a lot of code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Simon Guinot <simon.guinot@sequanux.org>
Cc: Valentin Longchamp <valentin.longchamp@keymile.com>
As some MVEBU platforms using the MVNETA driver seem to miss the
first ARP packet, lets reduce the timeout and increase the retry
count. This increases the speed for communication establishment.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
Instead of allocating space in the driver for the serdes
specification table, just allow the board file to set a pointer
to it. Also, allow the board to only specify the lanes that are
used instead of including unused lanes.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Functions that do not modify the pointer passed should declare it
as const.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
A lot of extra configuration information was left over in the
Marvell serdes and DDR3 initialization code for boards that
U-boot does not support. Remove this extra config information,
and the concept of fixing up board topologies with information
loaded from an EEPROM. If this needs to be done, it should be
handled in the board file, not in core code.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Use the is_power_of_2() definition from log2.h to align with the
kernel implementation.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Jagan Teki <jteki@openedev.com>
This patch adds driver model support for some Marvell MVEBU SoC's. Including
Armada XP and 38x. All 3 currently mainlined boards are converted. DM is now
selected automatically for MVEBU platforms.
With this DM support now available for MVEBU, hardcoding the base addresses
and other information is not necessary any more. Probing should be done
by using the values provided via the device tree now instead. For this
the driver also need to be converted to DM. Patches for some of the drivers
will follow.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Instead of calling board_init_r() directly from board_init_f(), just
return from board_init_f(). This will make the code continue executing
in crt0.S _main(), from which the board_init_r() is called. This patch
aligns the MVEBU SPL with the correct SPL design as well as reduces
the stack utilisation slightly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
When running on the AXP I sometimes noticed a strange behavior. As some
characters are not echoed on the U-Boot prompt. Not disabling the
lowlevel_init code, especially calling cpu_init_cp15() in the main
U-Boot seems to solve this issue.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables the use of the kwboot tool, to boot mainline U-Boot
on the Marvell Armada XP/38x SoC's. This is done by returning to the
SoC's BootROM after SPL has initialized the SDRAM. We need to make sure
to not reconfigure the internal register space and MBARs. Otherwise
the BootROM will not be able to continue after SPL jumps back to it.
To use this feature, please don't forget to change the BOOT_FROM line
in your board specfic kwbimage.cfg file this way:
BOOT_FROM uart
Tested on these Marvell eval boards:
DB-MV784MP-GP - Armada XP
DB-88F6820-GP - Armada 38x
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
As reported by Simon Guinot, commit ade741b3
"arm: mvebu: Call timer_init early before PHY and DDR init" breaks
Kirkwood platforms. As the static variable "init_done" is not
available at that early boot time. This patch moves it to explicitly
to the data section, making it available at that time.
Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Simon Guinot <simon.guinot@sequanux.org>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Tested-by: Simon Guinot <simon.guinot@sequanux.org>
Currently booting on A38x is broken. As the current code tries to detect
the SoC family to disable the MMU for the A38x at runtime. But before the
internal registers are switched to the new location (0xf100.0000), this
runtime detection does not work. As all macros / defines are already
assigned to the new location at 0xf100.0000. But the registers are sill
mapped to the default location at 0xd000.0000.
This patch now makes sure, no such runtime detection is used before
the internal registers are configured to the new location. After this,
the remaining cache cleanup is executed.
Signed-off-by: Stefan Roese <sr@denx.de>
Reported-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
introduce BIT() definition, used in at91_udc gadget
driver.
Signed-off-by: Heiko Schocher <hs@denx.de>
[remove all other occurrences of BIT(x) definition]
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
Acked-by: Stefan Roese <sr@denx.de>
Acked-by: Anatolij Gustschin <agust@denx.de>
This adds a PCI driver for the controllers found on Marvell MVEBU SoCs.
Besides the driver, this patch also removes the statically defined
PCI MBUS windows. As they are not needed anymore, since this PCIe
driver now creates the windows dynamically.
Tested on Armada XP db-mv784mp-gp eval board using an Intel E1000
PCIe card in all 3 PCIe slots. And on the Armada 38x db-88f6820-gp
eval board using this Intel E1000 PCIe card in the PCIe 0 slot.
This port was done in cooperation with Anton Schubert.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
This patch introduces the SDRAM scrubbing for ECC enabled board
to fill/initialize the ECC bytes. This is done via the XOR engine
to speed up the process. The scrubbing is a 2-stage process:
1) SPL scrubs the area 0 - 0x100.0000 (16MiB) for the main U-Boot
2) U-Boot scrubs the remaining SDRAM area(s)
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Rework these functions so that dram_init_banksize() does not call
dram_init() again. It only needs to set the banksize values in the
bdinfo struct.
Make sure to also clip the size of the last bank if it exceeds the
maximum allowed value of 3 GiB (0xc000.0000). Otherwise other
address windows (e.g. PCIe) will overlap with this memory window.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds "(ECC enabled)" or "(ECC disabled)" to the DRAM
bootup text. Making it easier for board with SPD DIMM's to see,
if ECC is enabled or not.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enables the USB EHCI support for the Marvell Armada XP (AXP)
SoCs. In compatism to the Armada 38x (A38x), the AXP needs to configure
the USB PLL and the USB PHY's specifically in U-Boot. The A38x has done
this already in the bin_hdr (SPL U-Boot). Without this, accessing the
controller registers in U-Boot or Linux will hang the CPU.
Additionally, the AXP uses a different USB EHCI base address. This
patch also takes care of this by runtime SoC detection in the Marvell
EHCI driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Cc: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch enables the NAND controller on the Armada XP/38x and provides
a new function that returns the NAND controller input clock. This
function will be used by the MVEBU NAND driver.
As part of this patch, the multiple BIT macro definitions are moved
to a common place in soc.h.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Accessing MBUS windows not backed-up by e.g. PCIe devices will
hang the SoC. Disable MBUS error propagation back to CPU allows
to read 0xffffffff instead of hanging the SoC.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Only with disabled MMU its possible to switch the base register address
on Armada 38x. Without this the SDRAM located at >= 0x4000.0000 is also
not accessible, as its still locked to cache.
So to fully release / unlock this area from cache, we need to first
flush all caches, then disable the MMU and disable the L2 cache.
On Armada XP this does not seem to be needed. Even worse, with this
code added, I sometimes see strange input charactes loss from the
console.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
With this patch, the MBUS bridge registers (base and size) are
configured upon each call to mbus_dt_setup_win(). This is needed, since
the board code can also call this function in later boot stages. As
done in the maxbcm board.
This is needed to fix a problem with the secondary CPU's not booting
in Linux on AXP.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Peter Morrow <peter@senient.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch changes the MBUS base addresses and sizes to use more
generic names and also adds defines for the sizes. It also moves
the base address to higher addresses.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
CONFIG_SYS_BOARD_DRAM_INIT is not defined anywhere. So lets get rid
of all references here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds basic SDIO/MMC booting support to MVEBU SoC's. Since
I don't know of a way to test the boot-device upon runtime, this patch
hardcodes the spl_boot_device instead.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Cc: Dirk Eibach <eibach@gdsys.de>
With the upcoming addition of the Armada 38x DDR support, which is not
compatible to the Armada XP DDR init code, we need to introduce a new
directory infrastructure. To support multiple Marvell DDR controller.
This will be the new structure:
drivers/ddr/marvell/axp
Supporting Armada XP (AXP) devices (and perhaps Armada 370)
drivers/ddr/marvell/a38x
Supporting Armada 38x devices (and perhaps Armada 39x)
Signed-off-by: Stefan Roese <sr@denx.de>
This code is ported from the Marvell bin_hdr code into mainline
SPL U-Boot. It needs to be executed very early so that the devices
connected to the serdes PHY are configured correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
With the upcoming addition of the Armada 38x SPL support, which is not
compatible to the Armada XP SERDES init code, we need to introduce a new
directory infrastructure. So lets move the AXP serdes init code into
a new directory. This way the A38x code can be added in a clean way.
Signed-off-by: Stefan Roese <sr@denx.de>
Only with disabled MMU its possible to switch the base register address on
Armada 38x. Without this the SDRAM located at >= 0x4000.0000 is also not
accessible, as its still locked to cache.
Signed-off-by: Stefan Roese <sr@denx.de>
Pin muxing needs to be done before UART output, since on A38x the UART
pins need some re-muxing for output to work.
Signed-off-by: Stefan Roese <sr@denx.de>
On A38x switching the regs base address without running from
SDRAM doesn't seem to work. So let the SPL still use the
default base address and switch to the new address in the
mail u-boot later.
Signed-off-by: Stefan Roese <sr@denx.de>
Without calling timer_init(), the xdelay() functions return immediately.
We need to call timer_init() early, so that these functions work and
the PHY and DDR init code works correctly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Anton Schubert <anton.schubert@gmx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch initializes the SATA address windows on Armada XP and
allows it to work with the existing mvsata_ide driver.
It also adds the necessary configuration for the db-mv784mp-gp board.
Signed-off-by: Anton Schubert <anton.schubert@gmx.de>
Tested-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds USB EHCI host support for the common mvebu platform.
Including the Armada 38x.
Tested on DB-88F6280-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This patch adds support for the common AHCI controller on the Marvell
Armada 38x.
Tested on the Marvell DB-88F6820-GP eval board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Armada A38x implements an SDHCI compatible SDIO controller. This patch
enables the Marvell driver to support this SoC. And enables the
SDIO controller if selected by the board configuration.
Tested on Marvell DB-88F6820-GP board.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Pantelis Antoniou <panto@antoniou-consulting.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
SMP-enabled Linux kernels read the CBAR register in CP15 to find
the address of the SCU registers. After remapping internal
registers, also update the CBAR so the kernel can find them.
Signed-off-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Acked-by: Stefan Roese <sr@denx.de>
L2 cache may still be enabled by the BootROM. We need to first disable
it before enabling d-cache support.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
By removing this default build target, the "u-boot.kwb" target is not
automatically generated. This fixes a temporary build error when using
out-of-tree builds, as buildman does per default (reported by Simon).
When the full SPL support is added for these targets with the DDR training
code, the "u-boot-spl.kwb" image will be generated automatically.
Users providing a special bin_hdr binary (binary.0) file can always add
this binary file and generate the full firmware image by issuing the
"make u-boot.kwb" command directly.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Luka Perkov <luka.perkov@sartura.hr>
This solves some RX problems that have been seen, when using the
mvneta ethernet driver. The cache needs to be reset into a "clean"
state before using it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
We are not using the coherency feature in U-Boot at all. So lets remove
this configuration from the mbus driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
With the introduction of the Armada 38x support, its necessary to change
the mvneta ethernet driver init call from always 4 times to a
configurable value. Lets make this init call more flexible by moving
the actually used devices to the config header.
Additionally this patch takes care of the slightly different base
addresses for the ethernet controllers on A38x.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds support for the Marvell Armada 38x SoC family.
Supported peripherals are:
- UART
- Ethernet (mvneta)
- I2C
- SPI (including SPI NOR flash)
Tested on Marvell DB-88F6820-GP evaluation board.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This way, new MVEBU boards don't need to specifiy the common location
for the SPL linker script.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
This define is used by the DDR training code for Armada XP. With the
upcoming addition of Armada 38x support, lets only define it for
Armada XP in this common header.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
MAX_MVNETA_DEVS is not used anywhere in U-Boot. So lets remove it.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Since these files will be used for other MVEBU SoC's, lets reflect this
in the headers marcos as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Now that the mach-mvebu directory exists and is used by Armada XP we can
move the mvebu-common files into this directory as well.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Move arch/arm/include/asm/arch-armada-xp/*
-> arch/arm/mach-mvebu/include/mach/*
Additionally the SYS_SOC is renamed from "armada-xp" to "mvebu". With this
change all these files can better be shared with other, newer Mavell
MVEBU SoC's. Like the upcoming Armada 38x support.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
Move arch/arm/cpu/armv7armada-xp/* -> arch/arm/mach-mvebu/*
Since this platform will be extended to support other Marvell SoC's as
well, lets rename it directly to mvebu.
This will be used by the upcoming Armada 38x suport (A38x).
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Masahiro Yamada <yamada.masahiro@socionext.com>
Tested-by: Kevin Smith <kevin.smith@elecsyscorp.com>
Tested-by: Dirk Eibach <dirk.eibach@gdsys.cc>
