In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_CPM_ADDR as the base of the CPM registers
instead of getting it via &immap->im_cpm.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
In the future the offsets to various blocks may not be in same location.
Move to using CFG_MPC85xx_GUTS_ADDR as the base of the guts registers
instead of getting it via &immap->im_gur.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Hello,
This patch ensures the soft reset of the board for the 85xx boards
by setting the MSR[DE] in the do_reset function.
Signed-off-by: Sughosh Ganu <urwithsughosh@gmail.com>
The mpc85xx start code uses some magic numbers that we actually
have #defines for in <config.h> so use those instead.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The PCI ID select values on the Arcadia main board differ depending
on the version of the hardware. The standard configuration supports
Rev 3.1. The legacy target supports Rev 2.x.
Signed-off-by Randy Vinson <rvinson@mvista.com>
This patch is against u-boot-mpc85xx.git of www.denx.com
Setting cpo to 0x9 for frequencies higher than 333MHz is verified on
both MPC8548CDS board and MPC8568MDS board, especially for supporting
533MHz DDR2.
Setting clk_adjust to 0x6(3/4 late cycle) for MPC8568MDS board is for
DDR2 on all current board versions especially ver 1.92 or later to bring
up.
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
On e500 when we leave the 4k boot page we should use an absolute address since
we don't know where the board code may want us to be really running at.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The current implementation does not set the number of bank address bits
(BA) in the processor. The default assumes 2 logical bank bits. This
works fine for a DIMM that uses devices with 4 internal banks (SPD
byte17 = 0x4) but needs to be set appropriately for a DIMM that uses
devices with 8 internal banks (SPD byte17 = 0x8).
Signed-off-by: Greg Davis <DavisG@embeddedplanet.com>
Some patches had inserted warnings into the build:
* mpc8560ads declared data without using it
* cpu_init declared ecm and immap without using it in all CONFIGs
* MPC8548CDS.h had its default filenames changed so that they contained
"\m" in the paths. Made the defaults not Windows-specific (or
anything-specific)
Signed-off-by: Andy Fleming <afleming@freescale.com>
From: Ed Swarthout <Ed.Swarthout@freescale.com>
Support external interrupts from platform to eliminate system hangs.
Define CONFIG_INTERRUPTS board configure option to enable.
Enable ecm, ddr, lbc, and pci/pcie error interrupts in PIC.
Remove extra cpu initialization redundant with hardware initialization.
Whitespace cleanup.
Define and use _START_OFFSET consistent with other processors using
ppc_asm.tmpl
Move additional code from .text to boot page to make room for
exception vectors at start of image.
Handle Machine Check, External and Critical exceptions.
Fix e500 machine check error determination in traps.c
TEXT_BASE can now be 0xfffc_0000 - which cuts binary image in half.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Only check for mpc8548 rev 1 when compiled for 8548.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Allow debugger to override flash cs0/cs1 settings to enable alternate
boot regions
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
This is a compatibility step that allows both the older form
and the new form to co-exist for a while until the older can
be removed entirely.
All transformations are of the form:
Before:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT)
After:
#if (CONFIG_COMMANDS & CFG_CMD_AUTOSCRIPT) || defined(CONFIG_CMD_AUTOSCRIPT)
Signed-off-by: Jon Loeliger <jdl@freescale.com>
For all practical u-boot purposes, TSECs don't differ throughout the
mpc8[356]xx families; reduce CONFIG_MPC8YXX_TSECx to CONFIG_TSECx.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
* Cleaned up the CDS PCI Config Tables and added NULL entries to
the end
* Fixed PCIe LAWBAR assignemt to use the cpu-relative address
* Fixed 85xx PCI code to assign powar region sizes based on the
config values (rather than hard-coding them)
* Fixed the 8548 CDS PCI2 IO to once again have 0 as the base address
Signed-off-by: Andy Fleming <afleming@freescale.com>
This included some changes to common files:
* Add 8568 processor SVR to various places
* Add support for setting the qe bus-frequency value in the dts
* Add the 8568MDS target to the Makefile
Signed-off-by: Andy Fleming <afleming@freescale.com>
Changed the code to read the registers and calculate the clock
rates, rather than using a "switch" statement.
Idea from Andrew Klossner <andrew@cesa.opbu.xerox.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
e500v2 and newer cores support 1G page sizes.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Enable single-bit error counter when memory was cleared by ddr controller.
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
Some device trees have a mac-address property, some have local-mac-address,
and some have both. To support all of these device trees, ftp_cpu_setup()
should write the MAC address to mac-address and local-mac-address, if they
exist.
Signed-off-by: Timur Tabi <timur@freescale.com>
* Cleaned up the TSR[WIS] clearing
* Cleaned up DMA initialization
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Recognize new SVR values, and add a few register definitions
Signed-off-by: Ed Swarthout <Ed.Swarthout@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Acked-by: Andy Fleming <afleming@freescale.com>
The following patch fixes the e500 v2 core reset bug.
For e500 v2 core, a new reset control register is added to reset the
processor.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Remove the fixed TLB and LAW entry nubmer. Use actually TLB and LAW
entry number to control the loop. This can reduce the potential risk
for the 85xx processor increasing its TLB adn LAW entry number.
Signed-off-by: Swarthout Edward <swarthout@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Introduced COFIG_FSL_I2C to select the common FSL I2C driver.
And removed hard i2c path from a few u-boot.lds scipts too.
Minor whitespace cleanups along the way.
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Modifications are based on the linux kernel approach and
support two use cases:
1) Add O= to the make command line
'make O=/tmp/build all'
2) Set environement variable BUILD_DIR to point to the desired location
'export BUILD_DIR=/tmp/build'
'make'
The second approach can also be used with a MAKEALL script
'export BUILD_DIR=/tmp/build'
'./MAKEALL'
Command line 'O=' setting overrides BUILD_DIR environent variable.
When none of the above methods is used the local build is performed and
the object files are placed in the source directory.
* Added comments and a printf to warn that PCI-X won't
work at 33MHz
Patch by Andy Fleming 17-Mar-2006
Signed-off-by: Andy Fleming <afleming@freescale.com>
