Add USB0 OTG support.
Currently, the USB0 OTG nodes are not enabled in the Linux kernel
devicetree.
For this reason, enable the USB0 OTG nodes inside imx8mp-evk-u-boot.dtsi
for now.
Also select several useful options such as USB gadget and fastboot.
Tested by running "ums 0 mmc 2".
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The GPIO3 has to be available early during U-Boot proper start up for
DRAM size detect to work correctly. The GPIO3 is currently available in
SPL and late in U-Boot proper, which is insufficient. Add the missing
bootph-all to make the GPIO3 available also early in U-Boot proper.
Signed-off-by: Marek Vasut <marex@denx.de>
Unselect CONFIG_CONSOLE_MUX to fix the following
error for the input, output and error interfaces:
U-Boot 2023.10 (Oct 03 2023 - 21:23:18 -0300)
...
In: No input devices available!
Out: No output devices available!
Err: No error devices available!
Net: eth0: ethernet@30be0000
Hit any key to stop autoboot: 0
Signed-off-by: Fabio Estevam <festevam@denx.de>
The xfi3 target has been removed by commit 539fba2c10 ("arm:
Remove xfi3 board"), but it missed to remove an entry from the
mxs Kconfig.
Remove it.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Commit 68dcbdd594 ("ARM: imx: Add weak default reset_cpu()") caused
the 'reset' command in U-Boot to not cause a board reset.
Fix it by switching to the watchdog driver model via sysreset, which
is the preferred method for implementing the watchdog reset.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
SPDX-License tag is missing and checkpatch complains about it.
Add the SPDX-License tag using the same one from imx7d-sdb.dts.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
The current imx8mp-dhcom-som.dtsi describes production rev.200 SoM,
add DT overlay which reinstates rev.100 SoM description to permit
prototype rev.100 SoMs to be used until they get phased out.
Signed-off-by: Marek Vasut <marex@denx.de>
In case the i.MX8MP DHCOM rev.100 has been populated on the PDK3
carrier board, the on-SoM PHY PHYAD1 signal has been pulled high
by the carrier board and changed the PHY MDIO address from 5 to 7.
This has been fixed on production rev.200 SoM by additional buffer
on the SoM PHYAD/LED signals, remove the workaround.
Signed-off-by: Marek Vasut <marex@denx.de>
The current imx8mp-dhcom-som.dtsi describes prototype rev.100 SoM,
update the DT to describe production rev.200 SoM which brings the
following changes:
- Fast SoC GPIOs exposed on the SoM edge connector
- Slow GPIOs like component resets moved to I2C GPIO expander
- ADC upgraded from TLA2024 to ADS1015 with conversion interrupt
- EEPROM size increased from 256 B to 4 kiB
Signed-off-by: Marek Vasut <marex@denx.de>
Add DT overlays to support additional DH i.MX8MP DHCOM SoM 660-100
population options with 1x or 2x RMII PHY mounted on PDK2 or PDK3
carrier boards.
Use SPL DTO support to apply matching SoM specific DTO to cater
for the SoM differences. Remove ad-hoc patching of control DT from
fdtdec_board_setup().
Signed-off-by: Marek Vasut <marex@denx.de>
Add board-specific function used to indicate whether a DTO from fitImage
configuration node 'fdt' property DT and DTO list should be applied onto
the base DT or not applied.
This is useful in case of DTOs which implement e.g. different board revision
details, where such DTO should be applied on one board revision, and should
not be applied on another board revision.
Signed-off-by: Marek Vasut <marex@denx.de>
The current code works by sheer coincidence, because (see HABv4 API
documentation, section 3.4) the RVT authenticate_image call updates
the size that is passed in with the actual size ROM code pulls from
IVT/CSF . So if the input size is larger, that is "fine" . Pass in
size instead to make this really correct.
Signed-off-by: Marek Vasut <marex@denx.de>
- Add some dependencies to CMD_DDR3 as this is only valid on some
platforms (which tend to select it as well).
- The proper gate for going in to cmd/ti is not
CONFIG_TI_COMMON_CMD_OPTIONS as nothing under there is controlled by
that symbol but the general TI architecture options.
Signed-off-by: Tom Rini <trini@konsulko.com>
- Generally we just drop the #ifdef CONFIG_SYS_LONGHELP and endif lines
and use U_BOOT_LONGHELP to declare the same variable name as before
- In a few places, either rename the variable to follow convention or
introduce the variable as it was being done inline before.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In order to be able to discard unused long help texts without further
linker lists, add a macro for defining the long help messages which uses
__maybe_unused. This allows us to discard them as unreferenced as part
of the link.
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the data version field of the EEPROM is not supported, provide a hexdump
of the data.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The different implementations of the mac command have board or vendor
specific sub-commands.
Add the command definition specific to the VisionFive 2 board.
Don't call cmd_usage() directly but return CMD_RET_USAGE instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
The different implementations of the mac command have board or vendor
specific sub-commands.
Add the command definition specific to the SiFive HiFive Unmatched board.
Don't call cmd_usage() directly but return CMD_RET_USAGE instead.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
CONFIG_SYS_LONGHELP=n we want to reduce the size of the U-Boot binary.
The long text should be reduced to and empty string in this case.
There is not need to call cmd_usage() directly. It is sufficient to
return CMD_RET_USAGE.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Board specific implementations of the 'mac' command differ concerning the
supported sub-commands.
Move the Freescale specific mac command definition to the board code.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Current codes only ennable the PER clock. However on iMX8 the LPUART
also needs IPG clock which is an LPCG. Should not depend on the default
LPCG setting.
Signed-off-by: Ye Li <ye.li@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
When CLK is enabled, get_lpuart_clk_rate() needs to get a per clock of
lpuart, so that add a per clock for lpuart1.
Signed-off-by: Alice Guo <alice.guo@nxp.com>
Reviewed-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
Add i.MX93 CCF driver support.
Modifed from Linux Kernel v6.5-rc2 and adapted for U-Boot.
Signed-off-by: Sébastien Szymanski <sebastien.szymanski@armadeus.com>
The USB_PWR signal operation is not reliable on this DWC3 controller
instance in case the signal is active high. Switch to GPIO control,
which always behaves correctly. Perform the change in u-boot extras
until this hits Linux upstream.
Signed-off-by: Marek Vasut <marex@denx.de>
The RD-AC5X doesn't make use of EFI or SMBIOS. Recently we started seeing
boot failures such as
WARNING: SMBIOS table_address overflow 27f60f020
Failed to write SMBIOS table
initcall failed at event 10/(unknown) (err=-22)
### ERROR ### Please RESET the board ###
The error is because the physical address of the RAM on the AC5X SoC is
above the 32GiB boundary. As we don't need SMBIOS or EFI this can be
safely disabled.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Handle 2GBit memory size value "2" from tlv eeprom on ddr
initialisation, to support SoMs with 512MB ddr memory.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Extend the existing tlv vendor extension used for ram size by one byte to
also store the number of ddr channels.
The length of the tlv entry can indicate whether the new information is
present. If not default to single channel.
Signed-off-by: Josua Mayer <josua@solid-run.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This reverts commit 5c1c6b7306. The reason
for switching to i2c-gpio was due to an issue we were seeing in the
Linux kernel where the CPU would lock up on certain adverse I2C bus
conditions. We were never able to reproduce the lockup in U-Boot but
assumed that was probably just luck.
Since then we have discovered that the lock up was due to the I2C
transaction offload engine in the I2C controller not coping with the
adverse bus conditions (basically it thinks there's another master and
waits for a STOP condition that never comes). U-Boot doesn't use the I2C
offload feature so is not susceptible to the lockup.
We can therefore safely return to using the built-in I2C controller.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The x240 doesn't make use of EFI or SMBIOS. Recently we started seeing
boot failures such as
WARNING: SMBIOS table_address overflow 23f60c020
Failed to write SMBIOS table
initcall failed at event 10/(unknown) (err=-22)
### ERROR ### Please RESET the board ###
The error is because the physical address of the RAM on the AC5X SoC is
above the 32GiB boundary. As we don't need SMBIOS or EFI this can be
safely disabled.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Starting with PCB revision 3 we can safely make use of higher RAM
frequency again. Make use of the EEPROM detection to determine the
revision and use the updated RAM timings for new SoMs.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add EEPROM detection initialisation for phyCORE-i.MX8MM and
print SoM information during boot when successful.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add helper function to read out the PCB revision of a PHYTEC SoM.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Due to PCB layout constraints in PCB revisions until including 1549.2,
a RAM frequency of 2 GHz can cause rare instabilities. Set the RAM
frequency to 1.5 GHz to achieve a stable system under all conditions.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Add imx8m specific detection part. Which includes checking the
EEPROM data for article number options.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Recent shipped PHYTEC SoMs come with an i2c EEPROM containing
information about the hardware such as board revision and variant.
This can be used for RAM detection and loading device tree overlays
during kernel start.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Yannic Moog <y.moog@phytec.de>
Tested-by: Yannic Moog <y.moog@phytec.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Add hook in sata_mv probe to enable bootstd bootdev.
Note: bootdev_setup_for_sibling_blk() invocation is a noop if bootsd is
not enabled for ahci sata yet.
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Stefan Roese <sr@denx.de>
ZyXEL NSA325 specifications:
Marvell Kirkwood 88F6282 SoC
1.6 GHz CPU
1x GBE LAN port (Marvell MV88E1318)
512 MB RAM
128 MB Eon NAND, SLC
I2C
1x USB 3.0 (on PCIe bus)
2x USB 2.0
2x SATA (hot swap slots)
Serial console
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The cn9130.dtsi defines a pinctrl node for SPI1 (until recently it was
mislabeled as spi0). Use this instead of having a duplicate definition
with a different label.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The CN9130-DB uses the SPI1 interface but had the pinctrl node labelled
as "cp0_spi0_pins". Use the label "cp0_spi1_pins" and update the node
name to "cp0-spi-pins-1" to avoid confusion with the pinctrl options for
SPI0.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The 2nd HD is not enabled in U-Boot on the D-Link DNS325. This patch
sets the responsible GPIO to high, enabling the drive.
Suggested-by: Peter Granilla
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tony Dinh <mibodhi@gmail.com>
The bootcmd_mfg env variable is legacy from IMX downstream u-boot branch
and is not needed on mainline.
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
