Add Nuvoton NPCM BMC Flash Interface Unit(FIU) SPI master
controller driver using SPI-MEM interface.
The FIU supports single, dual or quad communication interface.
The FIU controller driver provides flash access in UMA(User
Mode Access) mode by using an indirect address/data mechanism.
the dts node is followed upstream kernel dts name.
Signed-off-by: Jim Liu <JJLIU0@nuvoton.com>
Signed-off-by: Stanley Chu <yschu@nuvoton.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[Jagan: fixed the Kconfig, Makefile order]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add Macronix mx25u51245g flash entry, so this can be used on
SoCFPGA devices.
Signed-off-by: Tien Fong Chee <tien.fong.chee@intel.com>
[Jagan: updated commit head]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Add ID for Winbond W25Q128JW device. This is a 128 Mbit QSPI NOR.
Tested on W25Q128JWPIM part.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Horatiu Vultur <horatiu.vultur@microchip.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Cc: Stefan Roese <sr@denx.de>
Cc: Vignesh R <vigneshr@ti.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
To quote the author:
U-Boot provides a verified-boot feature based around FIT, but there is
no standard way of implementing it for a board. At present the various
required pieces must be built up separately, to produce a working
implementation. In particular, there is no built-in support for selecting
A/B boot or recovery mode.
This series introduces VPL, a verified program loader phase for U-Boot.
Its purpose is to run the verified-boot process and decide which SPL
binary should be run. It is critical that this decision happens before
SPL runs, since SPL sets up SDRAM and we need to be able to update the
SDRAM-init code in the field.
Adding VPL into the boot flow provides a standard place to implement
verified boot. This series includes the phase itself, some useful Kconfig
options and a sandbox_vpl build for sandbox. No verfied-boot support is
provided in this series.
Most of the patches in this series are fixes and improvements to docs and
various Kconfig conditions for SPL.
Add an initial VPL build for sandbox. This includes the flow:
TPL (with of-platdata) -> VPL -> SPL -> U-Boot
To run it:
./tpl/u-boot-tpl -D
The -D is needed to get the default device tree, which includes the serial
console info.
Add a Makefile check for OF_HOSTFILE which is the option that enables
devicetree control on sandbox.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add support for VPL, a new phase of U-Boot. This runs after TPL. It is
responsible for selecting which SPL binary to run, based on a
verified-boot process.
Signed-off-by: Simon Glass <sjg@chromium.org>
The current logic checks several options to decide whether SPL/TPL need
the U-Boot devicetree to be built. In fact we can check OF_CONTROL, which
is enabled in all cases that matter.
Signed-off-by: Simon Glass <sjg@chromium.org>
This feature is not available in SPL unless common/ and lib/ are built.
Update the Kconfig to avoid build errors.
Signed-off-by: Simon Glass <sjg@chromium.org>
MPP55 is used as a reset connected to the L3 switch chip. This doesn't
matter for u-boot as it doesn't use the L3 switch but it is useful to
be able to toggle the switch in/out of reset for the OS.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
This command is useful in U-boot scripts and it is being used by
OpenWrt bootscript for this board [1]. Otherwise shell scripting
commands are enabled by default in cmd/Kconfig.
[1] 852126680e/target/linux/mvebu/image/clearfog.bootscript (L7)
[2] e95afa5675/cmd/Kconfig (L1504)
Fixes: 0299c90f39 ("arm: mvebu: Add
SolidRun ClearFog Armada 38x initial support")
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
The Zyxel NSA310s board has the network chip Marvell Alaska 88E1318S.
Use uclass mvgbe and the compatible driver M88E1310 driver to bring
up Ethernet.
- Use uclass mvgbe to bring up the network. And remove ad-hoc code.
- Remove CONFIG_RESET_PHY_R.
- Enable CONFIG_PHY_MARVELL to properly configure the network.
- Add phy mode RGMII to kirkwood-nsa310s.dts
- Miscellaneous changes: Move constants to .c file and remove header file
board/zyxel/nsa310s/nsa310s.h, add support for large USB and SATA HDDs,
use BIT macro, add/cleanup comments, and cosmetic changes.
Note that this patch is depended on the following patch:
https://patchwork.ozlabs.org/project/uboot/patch/20220412201820.10291-1-mibodhi@gmail.com/
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
For most Kirkwood boards, the PHY page is already set to page 0
(in register 22) before phy_connect is invoked. But some board like
the Zyxel NSA310S (which uses the network chip MV88E1318S), the PHY page
is not set to page 0. There seems to be some bad data remained in
register 22 when the uclass MVGBE about to invoke phy_connect().
This patch enables the uclass MVGBE to always set the PHY page to 0
before phy_connect.
For reference, please see this discussion:
[RFC PATCH v2] arm: kirkwood: nsa310s: Use Marvell uclass mvgbe
and PHY driver for DM Ethernet.
https://lists.denx.de/pipermail/u-boot/2022-April/480946.html
This patch has been tested with the following Kirkwood boards:
NSA310S (88F6702, network chip MV88E1318S)
Sheevaplug (88F6281, network chip MV88E1318)
Pogo V4 (88F6192, network chip 88E1116R)
GF Home(88F6281, network chip 88E1116R)
Dreamplug (88F6281, network chip MV88E1318)
Dell Kace M300 (88F6282, network chip MV88E1318) - out of tree u-boot
Signed-off-by: Tony Dinh <mibodhi@gmail.com>
U-Boot for Turris Omnia is always compiled with MMC, SCSI and USB support,
so always enable macros for booting from these devices.
Signed-off-by: Pali Rohár <pali@kernel.org>
CONFIG_ETHPRIME defines primary ethernet device and env variable $ethact
stores currently active ethernet device.
So there is no point to set ethact= in default environment. Instead set
CONFIG_ETHPRIME properly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
PCIe Mini CEM 2.1 spec added support for USB3.0 mode on MiniPCIe cards.
USB3.0 and PCIe share same pins and only one function can be active at the
same time. PCIe Mini CEM 2.1 spec says that determining function is
platform specific and spec does not define any dedicated pin which could
say if card is USB3.0-based or PCIe-based.
Implement this platform specific decision (USB3.0 vs PCIe) for WWAN
MiniPCIe slot on Turris Omnia via U-Boot env variable "omnia_wwan_slot",
similarly like is implemented forced mode for MiniPCIe/mSATA slot via
"omnia_msata_slot" env variable. Value "usb3" for "omnia_wwan_slot" would
mean to set USB3.0 mode and value "pcie" original PCIe mode.
A385 SoC on Turris Omnia has configurable fifth SerDes line (exported to
MiniPCIe WWAN slot with SIM card) either to USB3.0 or PCIe functionality,
so implementation of this new PCIe Mini CEM 2.1 feature is simple, by just
configuring SerDes to USB 3.0 mode.
Other twos MiniPCIe slots on Turris Omnia do not have this new
functionality as their SerDes lines cannot be switched to USB3.0
functionality.
Note that A385 SoC does not have too many USB3.0 blocks, so activating
USB3.0 in MiniPCIe cause that one external USB3.0 USB-A port would loose
USB3.0 functionality and would be downgraded just to USB2.0.
By default this MiniPCIe WWAN slot is in PCIe mode, like before.
To set this MiniPCIe WWAN slot to USB3.0 mode, call U-Boot commands:
=> setenv omnia_wwan_slot usb3
=> saveenv
=> reset
Signed-off-by: Pali Rohár <pali@kernel.org>
Show error message when DT file does not contain sata or pcie node which
should be explicitly disabled. This can happen when U-Boot code for finding
those nodes is incomplete or when those DT nodes are in different
unexpected location. In any case it is needed to know if DT not was not
explicitly disabled as it could mean that combo slots where setup
incorrectly.
Signed-off-by: Pali Rohár <pali@kernel.org>
Move code for disabling sata and pcie DT nodes to own functions, so this
code can be called from other places in follow up patches.
Signed-off-by: Pali Rohár <pali@kernel.org>
Some PCIe-based MiniPCIe cards are broken and they do not ground PIN 43
which is required by PCIe mini CEM specs. Such broken cards are incorrectly
detected as mSATA cards because SATA specs requires that PIN 43 on mSATA
cards has to be disconnected.
PIN 43 on Turris Omnia is used only for MiniPCIe/mSATA card detection by
software in U-Boot SPL. Allow to override that U-Boot SPL detection by a
new "omnia_msata_slot" env variable (to value "pcie" or "sata") so broken
MiniPCIe cards can be used in combo mSATA/MiniPCIe slot too.
As configuration of PCIe vs SATA functionality is done in U-Boot SPL,
it is required to change env variable in permanent storage and reset the
board to take effect.
To force PCIe mode for broken MiniPCIe cards, call U-Boot commands:
=> setenv omnia_msata_slot pcie
=> saveenv
=> reset
Signed-off-by: Pali Rohár <pali@kernel.org>
By default use primary serdes map with PCIe function in combined
miniPCIe/mSATA slot. When SATA is detected change serdes map variable at
runtime.
Signed-off-by: Pali Rohár <pali@kernel.org>
BootROM maps SPI Flash to fixed address 0xD4000000 and this mapping is
active also when BootROM is executing binary kwbimage headers, which
includes also U-Boot SPL.
Therefore no initialization code is required to access SPI Flags from
U-Boot SPL. In proper U-Boot it is remapped to other location.
So in mvebu implementation of env_sf_get_env_addr() function returns
0xD4000000 when running in SPL and NULL when in proper U-Boot.
This change would allow to use U-Boot ENV in U-Boot SPL. Normally it is not
possible to read ENV because it is too big and U-Boot SPL does not have
such big malloc() pool to real all ENV variables.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Marek Behún <marek.behun@nic.cz>
In some cases it makes sense to use env_sf_init_addr() also in SPL mode.
Allow it for boards by providing custom implementation of weak function
env_sf_get_env_addr(). When this function returns NULL it signals that
address is invalid, like config option CONFIG_ENV_ADDR.
There is no change in default behavior or in config options.
Signed-off-by: Pali Rohár <pali@kernel.org>
UEFI:
* fix UEFI booting after integration of UEFI sub-system with driver model
* avoid random return values from devpath_is_partition()
* minor code clean ups
-----BEGIN PGP SIGNATURE-----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=IdkS
-----END PGP SIGNATURE-----
Merge tag 'efi-2022-07-rc2' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2022-07-rc2
UEFI:
* fix UEFI booting after integration of UEFI sub-system with driver model
* avoid random return values from devpath_is_partition()
* minor code clean ups
To quote the author:
I've been experimenting with ASAN on sandbox and turned up a few issues
that are fixed in this series.
Basic ASAN was easy to turn on, but integrating with dlmalloc was
messier and fairly intrusive. Even when I had it working, there was only
a small redzone between allocations which limits the usefulness.
I saw another series on the list by Sean Anderson to enable valgrind
which was finding a different set of issues, though there was one
overlap that Sean is fixing with
"[PATCH] IOMUX: Fix access past end of console_devices".
With these issues fixed, I was able to run the dm tests without any ASAN
issues. There are a couple of leaks reported at the end, but that's for
another day.
Use-after-free shouldn't be used, even in tests. It's bad practice and
makes the test brittle.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This tests calls regmap_read() which takes a uint pointer as an output
parameter. The test was passing a pointer to a u16 which resulted in an
overflow when the output was written. Fix this by following the
regmap_read() API and passing a uint pointer instead.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Cc: Jean-Jacques Hiblot <jjhiblot@ti.com>
Cc: Pratyush Yadav <p.yadav@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Data is written for each channel but is only tracked as having one
channel written. This resulted in a buffer overflow and corruption of
the allocator's metadata which caused further problems when the buffer
was later freed. This could be observed with sandbox unit tests.
Resolve the overflow by tracking the writes for each channel.
Fixes: f987177db9 ("dm: sound: Use the correct number of channels for sound")
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
The buffer is 512 bytes but read requests can be 800 bytes. Limit the
request to the size of the buffer.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When copying the string in copy_to_unicode(), check for the null
terminator in each position, not just at the start, to avoid reading
beyond the end of the string.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
There are expecte to be bars 0 through 5, but the last of these was
missing leading to an read beyond the buffer. Add the missing element
with zero values.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When do_acpi_dump() converts the table name to upper case, pass the
actual size of the output buffer so that the null terminator doesn't get
written beyond the end of the buffer.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Wolfgang Wallner <wolfgang.wallner@br-automation.com>
Cc: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The '--args' parameter to gdb comes before the binary that the debugger
will be attached to rather than after the binary and before the
arguments. Fix that in the docs.
Signed-off-by: Andrew Scull <ascull@google.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
efi_init_early() creates an event hook for block device probing.
It has to be called before any block device is probed.
Signed-off-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
While GPT partition is mandated in UEFI specification, CONFIG_PARTITION is
seen optional under the current implementation.
So modify efi_disk_rw_blocks() to allow accepting UCLASS_BLK devices.
Fixes: commit d97e98c887 ("efi_loader: disk: use udevice instead of blk_desc")
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Tested-by: Mark Kettenis <kettenis@openbsd.org>
