Based on observation, this udelay(20) was apparently too high and caused
subsequent failure to calibrate DDR when U-Boot was compiled with certain
toolchains. Lowering this delay fixed the problem.
Instead of permanently lowering the delay, calculate the correct delay
based on the original comment, that is, obtain EOSC1 frequency and use
it to calculate the precise delay.
Signed-off-by: Marek Vasut <marex@denx.de>
Fix the following problem:
drivers/ddr/altera/sequencer.c: In function 'sdram_calibration_full':
drivers/ddr/altera/sequencer.c:1943:25: warning: 'found_failing_read' may be used uninitialized in this function [-Wmaybe-uninitialized]
if (found_passing_read && found_failing_read)
^
drivers/ddr/altera/sequencer.c:1803:26: note: 'found_failing_read' was declared here
u32 found_passing_read, found_failing_read, initial_failing_dtap;
^
Signed-off-by: Marek Vasut <marex@denx.de>
This gem is really really rare, there was an actual float used in
the Altera DDR init code, which pulled in floating point ops from
the libgcc, just wow.
Since we don't support floating point operations the same way Linux
does not support them, replace this with an integer multiplication
and division combo. This removes some 2kiB of size from the SPL as
the floating point ops are no longer pulled in from libgcc.
This was detected by enabling CONFIG_USE_PRIVATE_LIBGCC=y , which
does not contain the floating point bits.
Signed-off-by: Marek Vasut <marex@denx.de>
Move config for the E1000 Ethernet driver to Kconfig and tidy up affected
boards.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Several files are out of order. This means that when the moveconfig tool
moves CONFIG options to Kconfig it generates a large diff. To avoid this,
reorder the files first.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add Kconfig options in preparation for moving boards to use Kconfig.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Update this driver to support driver model.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
Since struct eth_device does not exist with CONFIG_DM_ETH defined, avoid
using it in the driver unless necessary. Most of the time it is better to
pass the private driver pointer anyway.
Also refactor the code so that code that the driver model implementation
will share are available in functions that can be called. Add stubs where
necessary.
Signed-off-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
We cannot currently include any header files in the C files since common.h
needs to be included first, and it is in the header file. Move it.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Tested-on: Apalis T30 2GB on Apalis Evaluation Board
Current behavior is that if CTRL+C is pressed command returns 0 that was
successful which is not correct behavior.
The easiest test case is "tftpboot 80000 uImage && echo yes"
and press CTRL+C. Then the second command is called which is incorrect.
Error log:
zynq-uboot> tftpb 80000 uImage && echo yes
Gem.e000b000:7 is connected to Gem.e000b000. Reconnecting to
Gem.e000b000
Gem.e000b000 Waiting for PHY auto negotiation to complete....... done
Using Gem.e000b000 device
TFTP from server 192.168.0.102; our IP address is 192.168.0.101
Filename 'uImage'.
Load address: 0x80000
Loading: ################
Abort
yes
zynq-uboot>
This patch adds -EINTR return value when CTRL+C is pressed.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
High 32-bit address is needed when u-boot runs in 64-bit space.
Tested on armv8-based LS2085ARDB.
Signed-off-by: Mingkai Hu <Mingkai.Hu@freescale.com>
Signed-off-by: York Sun <yorksun@freescale.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Adjust timouts and retry counts to be suitable for loaded ethernet
network. With 5 seconds timeout, 10 retries maximum, tftp is
impossible even on local network with single full-speed TCP
connection.
100msec timeout should be suitable for most networks tftp is used on,
that is local ethernets. Timeout count really needs to be way higher,
as lost packets are normal when TCP is running over the same network.
Enforce 10msec minimum.
Signed-off-by: Pavel Machek <pavel@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Also move the spi flash configurations to the at91-sama5_common.h.
Current at91 zImage size is about 3.3M, the old mapping is not
suitable. So update the spi flash map as following:
0x0 ~ 0x004000: at91bootstrap(16k)
0x04000 ~ 0x008000: u-boot env(16k)
0x08000 ~ 0x060000: u-boot(352k)
0x60000 ~ 0x06c000: dtb (48k)
0x6c000 ~ 0x400000: kernel (3M+592k)
In AT91Bootstrap, the U-Boot in spi flash also update to 0x8000, refer
to following commit in AT91Bootstrap:
3e91e54 Kconfig: fix spi flash address
So also update SPL's u-boot load address to 0x8000 in spi flash.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
Since sama5d3xek boards has different type of dtb blobs, so we need to detect
the cpu type in runtime.
So we add a new variable $dtb_name. if $dtb_name is not defined, we just use
at91-${board_name}.dtb
as the $dtb_name. Otherwise, we will just load the dtb with
$dtb_name.
For sama5d3xek, we will detect cpu type and make up $dtb_name in
runtime.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
As almost all sama5 sd/mmc env configurations are same, so move them to
at91-sama5_common.h.
Also define CONFIG_ENV_VARS_UBOOT_CONFIG to have the varaible: $board_name.
Then we can use 'at91-${board_name}.dtb' as the dtb name.
TODO: since sama5d3xek has different dtb name, we need to some extra
stuff to make it work on sama5d3xek boards.
Signed-off-by: Josh Wu <josh.wu@atmel.com>
To enable the clocks on the at91 boards a constant (0x4) is used.
This is replaced with a define in at91_pmc.h (1 << 2).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Reviewed-by: Andreas Bießmann <andreas.devel@googlemail.com>
On these boards the DDR is connected to a dedicated controller and not
to chip select 1 of the EBI.
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
Tested-by: Erik van Luijk <evanluijk@interact.nl>
The mpddr.c depends on ATMEL_BASE_MPDDRC for the base address to configure the controller.
This cannot be used when there is more than one controller (i.e. AT91SAM9G45, AT91SAM9M10).
Signed-off-by: Erik van Luijk <evanluijk@interact.nl>
[remove 'new blank line at EOF']
Signed-off-by: Andreas Bießmann <andreas.devel@googlemail.com>
The syntax for the fdt_chosen/initrd
functions seem to deprecated in usage
from MIPS bootm implementation.
Third parameter is no more used in these api's
Refer to : include/fdt_support.h
Signed-off-by: Govindraj Raja <govindraj.raja@imgtec.com>
In commit a18a477 (MIPS: use common code from lib/time.c) MIPS platforms
started using common the common timer functions which are based around
the fact that many platforms have a 32-bit free running counter register
that can be used see commit 8dfafdd (Introduce common timer functions).
Even MIPS64 has such a 32-bit register (some have an additional 64-bit free
running counter, but that's something for another time).
The problem is that in __read_32bit_c0_register() we read the value from
this register into an _signed_ int and as it's returned up the call
chain to timer_read_counter() it gets assigned to an unsigned long. On a
32-bit system there is no problem. On a 64-bit system odd things happen,
sign extension seems to kick in and all of a sudden if the counter
register happens to have the MSb (i.e. the sign bit) set the negative
int gets sign extended into a very large unsigned long value. This in
turn throws out things from get_ticks() up.
Update __read_32bit_c0_register() and __read_32bit_c0_ctrl_register() to
use "unsigned int res;" instead of "int res;". There seems to be little
reason to treat these register values as signed. They are either
counters (which by definition are unsigned) or are made up of various
bit fields to be interpreted as per the CPU datasheet.
Reported-by: Sachin Surendran <sachin.surendran@alliedtelesis.co.nz>
Signed-off-by: Chris Packham <judge.packham@gmail.com>
This has not been converted to Generic Board, so should be removed.
(See doc/README.generic-board for details.)
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Heiko Schocher <hs@denx.de>
Acked-by: Marek Vasut <marex@denx.de>
This driver is not used only on exynos, but also on Altera SoCFPGA,
HiSilicon SoCs, RPi etc, so rename it accordingly to prevent confusion.
Signed-off-by: Marek Vasut <marex@denx.de>
populate _reset_ callback to the USB ethernet gadget since UDC core
expects every gadget driver to have the reset callback. This shouldn't
be needed once the ethernet gadget driver is adapted to use the
composite driver.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
xhci omap driver has board_usb_init in xhci_hcd_init but doesn't have
the corresponding cleanup function in xhci_hcd_stop.
Fix it here by invoking board_usb_cleanup() in xhci_hcd_stop().
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
Ethernet gadget driver can be used both by both SPL and u-boot. Since
usb_eth_init() is the entry point for ethernet gadget driver, perform
board initialization there. Also perform the cleanup in usb_eth_halt.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Marek Vasut <marex@denx.de>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Lukasz Majewski <l.majewski@samsung.com>
This patch fixes a potential NULL pointer dereference arising on
non-present/non-initialized xHCI controllers and adds some error
handling to xHCI code
Signed-off-by: Sergey Temerkhanov <s.temerkhanov@gmail.com>
Signed-off-by: Radha Mohan Chintakuntla <rchintakuntla@cavium.com>
USB EHCI on SPEAr600 has not been tested for a while. The base controller
addresses are missing. This patch adds the defines to the header. And adds
the missing code.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Viresh Kumar <viresh.kumar@linaro.org>
Cc: Vipin Kumar <vk.vipin@gmail.com>
Cc: Marek Vasut <marex@denx.de>
Document target board specific functions
board_ehci_hcd_init - override usb phy mode
board_ehci_hcd_init - set usb vbus voltage
board_ehci_power - enables/disables usb vbus voltage
Signed-off-by: Adrian Alonso <aalonso@freescale.com>
We have to set a MAC address to use network.
Otherwise, the tftpboot command fails with the following message:
Gem.e000b000 Waiting for PHY auto negotiation to complete........ done
*** ERROR: `ethaddr' not set
Since commit 92ac520821 ("net: Remove all references to
CONFIG_ETHADDR and friends"), we can not use CONFIG_ETHADDR.
The easiest way to set a MAC address is to enable
CONFIG_NET_RANDOM_ETHADDR.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
zynq-7000.dtsi include skeleton.dtsi which contains memory node with
base address and size zero. If you add memory@0 node to the platform DTS
in final DTB there are two memory nodes and U-Boot works with the first
one (with zeros) which end up in failing in dram_init because size is
zero.
Platform memory node should rewrite default memory node setup from
skeleton.dtsi that's why platfroms needs to also use memory as node name
instead of memory@0.
Reported-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We have to set a MAC address to use network.
Otherwise, the tftpboot command fails with the following message:
Gem.e000b000 Waiting for PHY auto negotiation to complete........ done
*** ERROR: `ethaddr' not set
Since commit 92ac520821 ("net: Remove all references to
CONFIG_ETHADDR and friends"), we can not use CONFIG_ETHADDR.
The easiest way to set a MAC address is to enable
CONFIG_NET_RANDOM_ETHADDR.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Use embedded DTB to let users use u-boot instead of u-boot-dtb.bin.
And fix SPL to use this target.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Added usb dwc3 driver support for zynqmp
this also supports the DFU and LTHOR to download
the linux images on to RAM and cen be booted from
those linux images.
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
One disadvantage of commit a26cd04920 (arch: Make board selection
choices optional) is that Kconfig could create such an insane
.config file that no board is selected.
Rip off the "optional" again in favor of ZC702 as the default
target.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Define checkboard() function for zynqMP
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Based on the patch:
"armv8: caches: Added routine to set non cacheable region"
(sha1: dad17fd510)
it is necessary to add platform specific hook.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
We have flipped CONFIG_SPL_DISABLE_OF_CONTROL. We have cleansing
devices, $(SPL_) and CONFIG_IS_ENABLED(), so we are ready to clear
away the ugly logic in include/fdtdec.h:
#ifdef CONFIG_OF_CONTROL
# if defined(CONFIG_SPL_BUILD) && !defined(SPL_OF_CONTROL)
# define OF_CONTROL 0
# else
# define OF_CONTROL 1
# endif
#else
# define OF_CONTROL 0
#endif
Now CONFIG_IS_ENABLED(OF_CONTROL) is the substitute. It refers to
CONFIG_OF_CONTROL for U-boot proper and CONFIG_SPL_OF_CONTROL for
SPL.
Also, we no longer have to cancel CONFIG_OF_CONTROL in
include/config_uncmd_spl.h and scripts/Makefile.spl.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
As we discussed a couple of times, negative CONFIG options make our
life difficult; CONFIG_SYS_NO_FLASH, CONFIG_SYS_DCACHE_OFF, ...
and here is another one.
Now, there are three boards enabling OF_CONTROL on SPL:
- socfpga_arria5_defconfig
- socfpga_cyclone5_defconfig
- socfpga_socrates_defconfig
This commit adds CONFIG_SPL_OF_CONTROL for them and deletes
CONFIG_SPL_DISABLE_OF_CONTROL from the other boards to invert
the logic.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There is no case where defined(SPL_DISABLE_OF_CONTROL) is true.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We do not want to compile the DM remove code for SPL. Currently,
we undef it in include/config_uncmd_spl.h (for C files) and in
scripts/Makefile.uncmd_spl (for Makefiles). This is really ugly.
This commit demonstrates how we can deprecate those two files.
Use $(SPL_) for the entry in the Makfile and CONFIG_IS_ENABLED()
in C files.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
