Compile the device tree of STM32MP13x boards and add the needed
U-Boot add-on.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add DT for DH DRC Compact unit, which is a universal controller device.
The system has two ethernet ports, one CAN, RS485 and RS232, USB, uSD
card slot, eMMC and SDIO Wi-Fi.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
AM62 StarterKit (SK) board is a low cost, small form factor board
designed for TI’s AM625 SoC. It supports the following interfaces:
* 2 GB DDR4 RAM
* x2 Gigabit Ethernet interfaces capable of working in Switch and MAC mode
* x1 HDMI Port with audio + x1 OLDI/LVDS Display interface for Dual Display
* x1 Headphone Jack
* x1 USB2.0 Hub with two Type A host and x1 USB Type-C DRP Port
* x1 UHS-1 capable µSD card slot
* 2.4/5 GHz WLAN + Bluetooth 4.2 through WL1837
* 512 Mbit OSPI flash
* x4 UART through UART-USB bridge
* XDS110 for onboard JTAG debug using USB
* Temperature sensors, user push buttons and LEDs
* 40-pin User Expansion Connector
* 24-pin header for peripherals in MCU island (I2C, UART, SPI, IO)
* 20-pin header for Programmable Realtime Unit (PRU) IO pins
* 15-pin CSI header
Add basic support for AM62-SK.
To keep the changes to minimum. Only UART And SD are supported at the
moment. This should serve as good example for adding new board support
based on AM62x SoC
Schematics: https://www.ti.com/lit/zip/sprr448
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
This is the initial support for Broadcom's ARM-based 47622 SOC.
In this change, our first SOC is an armv7 platform called 47622. The
initial support includes a bare-bone implementation and dts with ARM
PL011 uart.
The SOC-specific code resides in arch/arm/mach-bcmbca/<soc> and board
related code is in board/broadcom/bcmba.
The u-boot image can be loaded from flash or network to the entry
point address in the memory and boot from there.
Signed-off-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Kursad Oney <kursad.oney@broadcom.com>
Signed-off-by: Anand Gore <anand.gore@broadcom.com>
Reviewed-by: Philippe Reynes <philippe.reynes@softathome.com>
The bulk of it is (finally!) some DT sync from the kernel. We refrained
from syncing one incompatible change, as this would spoil booting Linux
kernels before v5.13 with U-Boot's DT (via UEFI, for instance).
I test booted Linux v5.18 and v5.4 with that new DT on some boards, and
the headless peripherals (MMC, USB, Ethernet) seemed to work.
The rest are fixes:
- silencing missing clock warnings due to the new pinctrl driver
- fixing "UART0 on PortF", allowing UART access through the SD card pins
- add an F1C100s clock driver, to enable MMC support (SPI comes later)
- some cleanups for CONS_INDEX_n in Kconfig
Tested on BananaPi-M1, Pine64-LTS, Pine-H64, X96-Mate (H616) and
OrangePi-Zero.
Add support for DH electronics i.MX8M Plus DHCOM SoM on PDK2 carrier board.
Currently supported are serial console, EQoS and FEC ethernets, eMMC, SD,
SPI NOR and USB 3.0 host.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Copy the devicetree source for the H6 SoC and all existing boards
from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 189bef235dd3 and 73088dfee635.
This commit also adds the following new board devicetrees:
- sun50i-h6-pine-h64-model-b.dts
- sun50i-h6-tanix-tx6-mini.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree for the R40/T3 SoC verbatim from the Linux v5.18-rc1
tag. None of the existing boards had any devicetree updates.
This commit adds the following new board devicetrees:
- sun8i-r40-oka40i-c.dts
- sun8i-t3-cqa3t-bv3.dts
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the V3(s)/S3 SoCs and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetrees:
- sun8i-s3-elimo-initium.dts
- sun8i-v3-sl631-imx179.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the H2+/H3/H5 SoCs and all existing
boards from the Linux v5.18-rc1 tag.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit also adds the following new board devicetree:
- sun8i-h3-nanopi-r1.dts
This update should not impact any existing U-Boot functionality.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A10s/A13/GR8, A31(s), and A23/A33/R16
SoCs and all existing boards from the Linux v5.18-rc1 tag.
These changes are combined into one commit due to interdependencies:
- The unit addresses were removed from bitbanged I2C buses, which
drives a Kconfig default change. This affects sun5i-a13-utoo-p66.dts
and sun6i-a31-colombus.dts.
- The pinctrl nodes were renamed, including some used by the shared
header sunxi-reference-design-tablet.dtsi.
To maintain ABI compatibility with existing LTS kernels, one change
moving some IP blocks to the r_intc interrupt controller is excluded.
This effectively reverts Linux commits 994e5818392c and 9fdef3c3d8c2.
This commit renames the file sun8i-r16-nintendo-nes-classic-edition.dts
to sun8i-r16-nintendo-nes-classic.dts to match the Linux tree.
This commit also adds the following new board devicetrees:
- sun5i-a13-licheepi-one.dts
- sun5i-a13-pocketbook-touch-lux-3.dts
- sun5i-gr8-evb.dts
- sun8i-a23-ippo-q8h-v1.2.dts
- sun8i-a23-ippo-q8h-v5.dts
- sun8i-a33-et-q8-v1.6.dts
- sun8i-a33-ippo-q8h-v1.2.dts
- sun8i-r16-nintendo-super-nes-classic.dts
As with the other SoCs, updates of note are conversion of GPIO pull-up
from pinconf to GPIO flags and renaming the detection GPIO properties in
the USB PHY nodes.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Copy the devicetree source for the A20 SoC and all existing boards
verbatim from the Linux v5.18-rc1 tag.
This commit also adds the following new board devicetrees:
- sun7i-a20-haoyu-marsboard.dts
- sun7i-a20-linutronix-testbox-v2.dts
- sun7i-a20-olinuxino-lime-emmc.dts
This update includes changes to the USB PHY detection GPIO properties
which are needed to convert that driver to use the DM GPIO framework.
Signed-off-by: Samuel Holland <samuel@sholland.org>
[Andre: fix Mele M5 U-Boot only DT]
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Migrate DH picoITX device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Migrate DH DRC02 device trees from Linux commit 42226c989789
(tag v5.18-rc7). No changes have been made, the DTs are exact copies.
Furthermore add the DTB to dh_imx6_defconfig.
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Philip Oberfichtner <pro@denx.de>
The Bosch ACC (Air Center Control) Board is based on the i.MX6D.
The device tree is copied from Linux, see [1]. The only difference
compared to the Linux DT is the removal of usbphynop properties. They are
defined in the Linux version of imx6qdl.dtsi, but not in the u-boot
version.
[1] Commit 6192cf8ac082 from
git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
Signed-off-by: Philip Oberfichtner <pro@denx.de>
Sync BeagleBone dts files & TPS dtsi files with Linux v5.17 and include
the SanCloud BBE Extended WiFi dts added in v5.18-rc1. Also pull in
changes to am33xx-l4.dtsi needed to support the BeagleBone Blue.
The change to use the cpsw switch driver (commit c477358e66a3 in Linux)
is excluded from the sync as u-boot does not recognise the new
compatible string.
Signed-off-by: Paul Barker <paul.barker@sancloud.com>
The GW74xx is based on the i.MX 8M Plus SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- PCIe Gen 3.0 switch (build option)
- USB 3.0 HUB
- USB Type-C front panel connector
- GPS
- 3-axis accelerometer
- CAN bus
- 6x GbE RJ45 front-panel jacks
- 1x IMX8M FEC RGMII GbE (with Passive PoE)
- 5x IMX8M EQOS RGMII 6 port GbE Switch
(1x with 802.3af class 5 Active PoE)
- RS232/RS485/RS422 serial transceiver
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- DigI/O header (UART/GPIO/I2C/ADC)
- 802.11ac WiFi
- Bluetooth BLE
- 3x MiniPCIe sockets with PCI/USB
- 1x M.2 Socket with USB2.0, PCIe, and dual-SIM
- PMIC
- Wide range DC input supply (8V to 60V DC)
Do the following to add support for this and future imx8mp-venice boards:
- add dts
- add DRAM config
- add PMIC config
- add IMX8MP support in spl.c and venice.c
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Drop Apalis iMX8X platform as it never left sample state and is no
longer supported.
Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
MK808 is a RK3066-based board with 1 USB host and 1 USB OTG port,
HDMI and a micro-SD card slot. It also includes on-board NAND
and 1GB of SDRAM. Add rk3066a-mk808.dts. Move U-boot specific
things in a rk3066a-mk808-u-boot.dtsi file.
Signed-off-by: Johan Jonker <jbx6244@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD socket with voltage select support
- Gateworks System Controller
- M.2 A-E Socket with USB2.0 and PCIe
- MiniPCIe Socket with PCIe, USB2.0, and SIM
- IMX8M FEC
- RS232/RS485/RS422 serial transceiver
- LIS2DE12 3-axis accelerometer
- front panel LED's
- off-board isolated digital I/O
- Wide range DC power input
- 802.3at PoE
- PMIC
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Add new board based on the Toradex Verdin iMX8M Mini SoM, the MX8Menlo.
The board is a compatible replacement for i.MX53 M53Menlo and features
USB, multiple UARTs, ethernet, LEDs, SD and eMMC.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Add support for Data Modul i.MX8M Mini eDM SBC board. This is an
evaluation board for various custom display units. Currently
supported are serial console, ethernet, eMMC, SD, SPI NOR,
USB host and USB OTG.
Reviewed-by: Fabio Estevam <festevam@denx.de>
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAmJH28ocHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyDv4B/9FBx95f7zR6WmguG05
VyBchjphsRSuXHb7NieVNNEIpCJu+zw8YutngN2Q8KWIbM9o1OZnrNGxuKR9s+Px
ivMXytGGsIa74XXhxv2boX151R1a5TG4UPf4Vn20qxmUiScE4FaoW5wQHG2vGqxd
/LbzENNCA1A41/RGGysqyY8nQgOEY+Iass+OaHe7XjngcCfY5oY4IRqJ/Ak7ojkv
Vm46i+KCTuyBlcMDjAwDsukSmzsujz2FyzZU1Uy62N8quEdXgrlIA/Yh4oarZ+BO
5W/BJe1rClbnBkMJJn71GUlmnYrioYeUvxvIYwZWooe0Hgr+Iv1vOXv8aJ4hBsdc
yoje
=SwGu
-----END PGP SIGNATURE-----
Merge tag 'u-boot-at91-2022.07-a' of https://source.denx.de/u-boot/custodians/u-boot-at91 into next
First set of u-boot-at91 features for the 2022.07 cycle:
This feature set includes the new driver for the Atmel TCB timer,
alignment in DT for sama7g5 and sama7g5ek board, one Kconfig conversion
for external reset, and the usage of Galois tables from ROM for sama5d2
device.
The ARMv8-R64 architecture introduces optional VMSA (paging based MMU)
support in the EL1/0 translation regime, which makes that part mostly
compatible to ARMv8-A.
Add a new board variant to describe the "BASE-R64" FVP model, which
inherits a lot from the existing v8-A FVP support. One major difference
is that the memory map in "inverted": DRAM starts at 0x0, MMIO is at
2GB [1].
* Create new TARGET_VEXPRESS64_BASER_FVP target, sharing most of the
exising configuration.
* Implement inverted memory map in vexpress_aemv8.h
* Create vexpress_aemv8r defconfig
* Provide an MMU memory map for the BASER_FVP
* Update vexpress64 documentation
At the moment the boot-wrapper is the only supported secure firmware. As
there is no official DT for the board yet, we rely on it being supplied
by the boot-wrapper into U-Boot, so use OF_HAS_PRIOR_STAGE, and go with
a dummy DT for now.
[1] https://developer.arm.com/documentation/100964/1114/Base-Platform/Base---memory/BaseR-Platform-memory-map
Signed-off-by: Peter Hoyes <Peter.Hoyes@arm.com>
[Andre: rebase and add Linux kernel header]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[trini: Add MAINTAINERS entry for Peter]
The FVP base model is relying on a DT for Linux operation, so there is
no reason we would need to rely on hardcoded information for U-Boot.
Letting U-Boot use a DT will open up the usage of actual peripherals,
beyond the support for semihosting only.
Enable OF_CONTROL in the Kconfig, and use the latest dts files from
Linux. Depending on whether we use the boot-wrapper or TF-A, there is
already a DTB provided or not, respectively.
To cover the boot-wrapper, we add an arm64 Linux kernel header, which
allows the boot-wrapper to treat U-Boot like a Linux kernel. U-Boot will
find the pointer to the DTB in x0, and will use it.
Even though TF-A carries a DT, at the moment this is not made available
to non-secure world, so to not break users, we use the U-Boot provided
DTB copy in that case. For some reason TF-A puts some DT like structure
at the address x0 is pointing at, but that is very small and doesn't
carry any hardware information. Make the code to ignore those small DTBs.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
In Linux this DT file is named at91-sama7g5ek.dts. Rename it accordingly.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Add support for Kevin, an RK3399-based convertible chromebook that is
very similar to Bob. This patch is mostly based on existing support for
Bob, with only minor changes for Kevin-specific things.
Unlike other Gru boards, coreboot sets Kevin's center logic to 925 mV,
so adjust it here in the dts as well. The rk3399-gru-kevin devicetree
has an unknown event code reference which has to be defined, set it
to the Linux counterpart. The new defconfig is copied from Bob with the
diffconfig:
DEFAULT_DEVICE_TREE "rk3399-gru-bob" -> "rk3399-gru-kevin"
DEFAULT_FDT_FILE "rockchip/rk3399-gru-bob.dtb" -> "rockchip/rk3399-gru-kevin.dtb"
VIDEO_ROCKCHIP_MAX_XRES 1280 -> 2400
VIDEO_ROCKCHIP_MAX_YRES 800 -> 1600
+TARGET_CHROMEBOOK_KEVIN y
With this Kevin can boot from SPI flash to a usable U-Boot prompt on the
display with the keyboard working, but cannot boot into Linux for
unknown reasons.
eMMC starts in a working state but fails to re-init, microSD card works
but at a lower-than-expected speed, USB works but causes a hang on
de-init. There are known workarounds to solve eMMC and USB issues.
Cc: Marty E. Plummer <hanetzer@startmail.com>
Cc: Simon Glass <sjg@chromium.org>
[Alper: commit message, resync config with Bob, update MAINTAINERS,
add to Rockchip doc, add Kconfig help message, set regulator]
Co-developed-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
-----BEGIN PGP SIGNATURE-----
iF0EABECAB0WIQQbPNTMvXmYlBPRwx7KSWXLKUoMIQUCYjIBkgAKCRDKSWXLKUoM
IYUwAKCYRBxb59BFq4MRvTbNcRZ7H4oGIQCfVUl3x9KZ7nFZaYAaBXFBxwna+PE=
=irCR
-----END PGP SIGNATURE-----
Merge tag 'xilinx-for-v2022.07-rc1' of https://source.denx.de/u-boot/custodians/u-boot-microblaze into next
Xilinx changes for v2022.07-rc1
microblaze:
- Add support for reserved memory
xilinx:
- Update FRU code with MAC reading
zynqmp:
- Remove double AMS setting
- DT updates (mostly for SOMs)
- Add support for zcu106 rev 1.0
zynq:
- Update nand binding
nand:
- Aligned zynq_nand to upstream DT binding
net:
- Add support for ethernet-phy-id
mmc:
- Workaround CD in zynq_sdhci driver also for ZynqMP
- Add support for dynamic/run-time SD config for SOMs
gpio:
- Add driver for slg7xl45106
firmware:
- Add support for dynamic SD config
power-domain:
- Update zynqmp driver with the latest firmware
video:
- Add skeleton driver for DP and DPDMA
i2c:
- Fix i2c to work with QEMU
pinctrl:
- Add driver for zynqmp pinctrl driver
This adds platform code and the device tree for the Phytium Pomelo Board.
The initial support comprises the UART and the PCIE.
Signed-off-by: weichangzheng <nicholas_zheng@outlook.com>
This add the initial support of the broadcom reference
board bcm96753ref with a bcm6753 SoC.
This board has 1 GB of RAM, 256 MB of flash (nand),
2 USB port, 1 UART, and 4 ethernet ports.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The GW7902 is based on the i.MX 8M Mini / Nano SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- Gateworks System Controller
- LTE CAT M1 modem
- USB 2.0 HUB
- M.2 Socket with USB2.0, PCIe, and dual-SIM
- IMX8M FEC
- PCIe based GbE
- RS232/RS485/RS422 serial transceiver
- GPS
- CAN bus
- WiFi / Bluetooth
- MIPI header (DSI/CSI/GPIO/PWM/I2S)
- PMIC
To add support for the i.MX8M Nano GW7902:
- Add imx8mn-venice dts/defconfig/include
- Add imx8mn-gw7902 dts
- Add imx8mn-2gb lpddr4 dram configs
- Add misc support for IMX8M Nano SoC
- rename imx8mm-venice.c to venice.c as it is no longer imx8mm specific
- update README with differences for IMX8MN vs IMX8MM
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
J721E Starter Kit (SK)[1] is a low cost, small form factor board designed
for TI’s J721E SoC. TI’s J721E SoC comprises of dual core A72, high
performance vision accelerators, video codec accelerators, latest C71x
and C66x DSP, high bandwidth real-time IPs for capture and display, GPU,
dedicated safety island and security accelerators. The SoC is power
optimized to provide best in class performance for industrial and
automotive applications.
J721E SK supports the following interfaces:
* 4 GB LPDDR4 RAM
* x1 Gigabit Ethernet interface
* x1 USB 3.0 Type-C port
* x3 USB 3.0 Type-A ports
* x1 PCIe M.2 E Key
* x1 PCIe M.2 M Key
* 512 Mbit OSPI flash
* x2 CSI2 Camera interface (RPi and TI Camera connector)
* 40-pin Raspberry Pi GPIO header
Add A72 specific dts for J721E-SK.
[1] https://www.ti.com/tool/SK-TDA4VM
Signed-off-by: Sinthu Raja <sinthu.raja@ti.com>
When building for a custom board, it is quite common to maintain a
private branch which include some defconfig and .dts files. But to
hook up those .dts files requires modifying a file "belonging" to
upstream U-Boot, the arch/*/dts/Makefile. Forward-porting that branch
to a newer upstream then often results in a conflict which, while it
is trivial to resolve by hand, makes it harder to have a CI do "try to
build our board against latest upstream".
The .config usually includes information on precisely what .dtb(s) are
needed, so to avoid having to modify the Makefile, simply add the
files in (SPL_)OF_LIST to dtb-y.
A technicality is that (SPL_)OF_LIST is not always defined, so rework
the Kconfig symbols so that (SPL_)OF_LIST is always defined (when
(SPL_)OF_CONTROL), but only prompted for in the cases which used to be
their "depends on".
nios2 and microblaze already have something like this in their
dts/Makefile, and the rationale in commit 41f59f6853 is similar to
the above. So this simply generalizes existing practice. Followup
patches could remove the logic in those two makefiles, just as there's
potential for moving some common boilerplate from all the
arch/*/dts/Makefile files to the new scripts/Makefile.dts.
Signed-off-by: Rasmus Villemoes <rasmus.villemoes@prevas.dk>
Reviewed-by: Simon Glass <sjg@chromium.org>
The EVM architecture for J721S2 is similar to that of J721E and J7200. It
is as follows,
+------------------------------------------------------+
| +-------------------------------------------+ |
| | | |
| | Add-on Card 1 Options | |
| | | |
| +-------------------------------------------+ |
| |
| |
| +-------------------+ |
| | | |
| | SOM | |
| +--------------+ | | |
| | | | | |
| | Add-on | +-------------------+ |
| | Card 2 | | Power Supply
| | Options | | |
| | | | |
| +--------------+ | <---
+------------------------------------------------------+
Common Processor Board
Common Processor board is the baseboard that contains most of the actual
connectors, power supply etc. The System on Module (SoM) is plugged on to
the common processor baord. Therefore, add support for peripherals brought
out in the common processor board.
Link to Common Processor Board: https://www.ti.com/lit/zip/sprr439
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
This adds initial support for the Toradex Verdin iMX8M Plus Quad 4GB WB
IT V1.0B module. They are strapped to boot from eFuses which are factory
fused to properly boot from their on-module eMMC. U-Boot supports
booting from the on-module eMMC only, SDP support is disabled for now
due to missing i.MX 8M Plus USB support.
Functionality wise the following is known to be working:
- eMMC, 8-bit and 4-bit MMC/SD card slots
- Ethernet both on-module eQoS and FEC (requires PHY on carrier board)
- GPIOs
- I2C
Boot sequence is:
SPL ---> ATF (TF-A) ---> U-boot proper
ATF, U-boot proper and u-boot.dtb images are packed into a FIT image,
loaded by SPL.
Boot:
U-Boot SPL 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
Quad die, dual rank failed, attempting dual die, single rank configuration.
Normal Boot
WDT: Started watchdog@30280000 with servicing (60s timeout)
Trying to boot from BOOTROM
Find img info 0x&48025a00, size 872
Need continue download 1024
Download 779264, Total size 780424
NOTICE: BL31: v2.2(release):rel_imx_5.4.70_2.3.2_rc1-5-g835a8f67b
NOTICE: BL31: Built : 16:52:37, Aug 26 2021
U-Boot 2022.04-rc1-00164-g21a0312611-dirty (Feb 07 2022 - 11:34:04 +0100)
CPU: Freescale i.MX8MP[8] rev1.1 at 1200 MHz
Reset cause: POR
DRAM: 8 GiB
Core: 78 devices, 18 uclasses, devicetree: separate
WDT: Started watchdog@30280000 with servicing (60s timeout)
MMC: FSL_SDHC: 1, FSL_SDHC: 2
Loading Environment from MMC... OK
In: serial
Out: serial
Err: serial
Model: Toradex Verdin iMX8M Plus Quad 4GB Wi-Fi / BT IT V1.0B, Serial# 06817281
Carrier: Toradex Verdin Development Board V1.1A, Serial# 10807609
Setting variant to wifi
Net: Hard-coding pdata->enetaddr
eth1: ethernet@30be0000, eth0: ethernet@30bf0000 [PRIME]
Hit any key to stop autoboot: 0
Verdin iMX8MP #
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
