2
0
Fork 0
mirror of https://github.com/AsahiLinux/u-boot synced 2024-12-23 03:23:47 +00:00
Commit graph

65 commits

Author SHA1 Message Date
Tom Rini
6cc04547cb global: Migrate CONFIG_SYS_FSL* symbols to the CFG_SYS namespace
Migrate all of COFIG_SYS_FSL* to the CFG_SYS namespace.

Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-11-10 10:08:55 -05:00
Marcel Ziswiler
50ba171e2d apalis_imx6: synchronise device tree with linux
Synchronise device tree with linux-next 20220706.

Please note that this also means that instead of the previous "generic"
U-Boot specific carrier board agnostic device tree we are now using the
regular one for the Apalis Evaluation (carrier) board (e.g.
imx6q-apalis-eval.dtb rather than the previous imx6-apalis.dtb).

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-07-25 16:12:00 +02:00
Francesco Dolcini
66af2c3e95 board: apalis_imx6: DDR init using mx6_dram_cfg()
Do DDR initialization using the procedural mx6_dram_cfg() instead of
programming the MMDC using a raw list of register/value pairs, this
solves some rare boot failures on specific "bad" modules.

Calibration values, DDR geometry are unchanged, memory timings are
updated according to the relevant memory datasheet, no changes on
the power consumption.

For IT temperature range SKUs CL is decreased from 8 to 7 and tFAW
value is increased, for commercial temperature range SKUs some
changes on ODT parameters.

This change was validated over a range of different apalis-imx6 SoM, on
the whole working temperature range with weeks of continuous testing.

Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-06-28 15:24:31 +02:00
Francesco Dolcini
d4cd19ded8 toradex: apalis/colibri_imx6: Fix CLKO1/CLKO2 output
Set CLK01 and CLK02 to 24MHz and enable it in CCM_CCOSR register.

This clock is used by both the audio codec (CLKO1) and by the CSI camera
(CLKO2) and is expected to be 24MHz.

Despite the wrong 16.5MHz there was no real issue because of the wrong
frequency since Linux reconfigures the clocks afterward, however this
was triggering an issue with noise coming from the SGTL5000 audio codec.

The problem is that the SGTL5000 does not have a reset pin and after it
is configured if the input MCLK clock is disabled it produces a constant
noise on its output, this was happening on software reboot.

Forcing the clock to be enabled in U-Boot prevent the problem by making
sure that the clock is always available, without this change as soon as
Linux was changing the clock tree (setting clk_out_sel=1 without setting
clko2_en=1) the noise would start till the actual clock was enabled
(clko2_en=1) during the SGTL5000 driver probe.

Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Fabio Estevam <festevam@denx.de>
2022-06-28 15:24:31 +02:00
Marcel Ziswiler
405c97fd1d configs: tdx: apalis_imx6: drop hw v1.0 support
Drop optional support for the ancient Apalis iMX6 V1.0 hardware which
had the UART wired as DCE rather than DTE.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-21 12:44:23 +02:00
Denys Drozdov
b8055ee176 apalis-imx6: avoid save environment unasked
U-Boot should never save the environment unasked.
This also avoids storing broken ftd_file to eMMC.

Signed-off-by: Denys Drozdov <denys.drozdov@toradex.com>
Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2022-04-12 19:10:44 +02:00
Marcel Ziswiler
c7b24915cf toradex: take over maintainership
Also take over maintainership of remaining Toradex SoMs as Oleksandr
has left our company.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
CC: Oleksandr Suvorov <cryosay@gmail.com>
2021-10-20 17:49:59 +02:00
Francesco Dolcini
a591e75fbc apalis-imx6: use dynamic DDR calibration
Enable dynamic DDR calibration to have a reliable behavior on edge
temperatures conditions.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
2021-10-19 10:51:39 +02:00
Tom Rini
9774462e34 arm: Disable ATAGs support
With the exceptions of ds109, ds414, icnova-a20-swac, nokia_rx51 and
stemmy, disable ATAG support.  A large number of platforms had enabled
support but never supported a kernel so old as to require it.  Further,
some platforms are old enough to support both, but are well supported by
devicetree booting, and have been for a number of years.  This is
because some of the ATAGs related functions have been re-used to provide
the same kind of information, but for devicetree or just generally to
inform the user.  When needed still, rename these functions to
get_board_revision() instead, to avoid conflicts.  In other cases, these
functions were simply unused, so drop them.

Cc: Andre Przywara <andre.przywara@arm.com>
Cc: Jagan Teki <jagan@amarulasolutions.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Stefan Bosch <stefan_b@posteo.net>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-09-07 16:22:30 -04:00
Michal Simek
b4c2c151b1 Kconfig: Remove all default n/no options
default n/no doesn't need to be specified. It is default option anyway.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
[trini: Rework FSP_USE_UPD portion]
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-08-31 17:47:49 -04:00
Harald Seiler
35b65dd8ef reset: Remove addr parameter from reset_cpu()
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-03-02 14:03:02 -05:00
Simon Glass
401d1c4f5d common: Drop asm/global_data.h from common header
Move this out of the common header and include it only where needed.  In
a number of cases this requires adding "struct udevice;" to avoid adding
another large header or in other cases replacing / adding missing header
files that had been pulled in, very indirectly.   Finally, we have a few
cases where we did not need to include <asm/global_data.h> at all, so
remove that include.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>
2021-02-02 15:33:42 -05:00
Tom Rini
b11f634b1c Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
 dtoc: Tidy up and add more tests
 ns16550 code clean-up
 x86 and sandbox minor fixes for of-platdata
 dtoc prepration for adding build-time instantiation
 -----BEGIN PGP SIGNATURE-----
 
 iQFFBAABCgAvFiEEslwAIq+Gp8wWVbYnfxc6PpAIreYFAl/09LURHHNqZ0BjaHJv
 bWl1bS5vcmcACgkQfxc6PpAIrebjwwf/fHRjYsAY/Yj/+y1xgo3L3sphIvQUqTDF
 KkLl+kHdV5r8W/HJULxLQcF2r7pcPEI6TAQxuj3qQ5SUvm2HviS8GHGPawDEwyht
 HgBp9VD56+HUadMfnbG//DVS73ycbL4XSKlYqpkINEejtnlttsCIawUXX5cTyGM/
 59VkgnKrKvJQRUXvYLa8MTugTs4fkPJGDqhActBk/7SP1SImj+rfalNSqA2/dx6y
 2RnPCSzB1x2231KSj+B1NgGlR3Xb8P8zgh20ijcEU/hrlXBTZyi7K7f4SJR30Efu
 LYkkuj4VbxcV/25RozR0fmknqCs0QyAI+/dql6TNtbTSPC/jAfj0jQ==
 =9kN3
 -----END PGP SIGNATURE-----

Merge tag 'dm-pull-5jan21' of git://git.denx.de/u-boot-dm into next

Driver model: make some udevice fields private
Driver model: Rename U_BOOT_DEVICE et al.
dtoc: Tidy up and add more tests
ns16550 code clean-up
x86 and sandbox minor fixes for of-platdata
dtoc prepration for adding build-time instantiation
2021-01-05 22:34:43 -05:00
Tom Rini
720620e691 Prepare v2021.01-rc5
-----BEGIN PGP SIGNATURE-----
 
 iQGzBAABCgAdFiEEGjx/cOCPqxcHgJu/FHw5/5Y0tywFAl/0YVIACgkQFHw5/5Y0
 tywtEwv/cJWlKgcSnYjuJrxwuJdauUTfXdbUgtCxOtBw/BP4dsKkbGTJPw5q5M+4
 LJJSKyksmJVTX26h1dpkzQjOpWtTDnWqm5CTIxD52oQD7pxK+zCQ9T6S+QbQD0Se
 ogHmZluzFoluxbNgo8tiO52xvMhDO3TVAzxsNDdGfkd5/tAXOHClPc34RmAkdRHU
 VsR89AKdT2q543fiUfrRZYDzdctaNWhRGXMDcJ4+QU/8hQhrpcr8EtHbF+3mWX4K
 pA01pDz150Rn4UI6S2xKEWrjSTHe55fxVj/Qj0rq9z2E/+NqGXemf5s13AR0G/z3
 PqHdVLHzDe64pbOvmyU1pVQ0aMb8vMJUnqx68SQZY3On2c+MjRWQ+7aVVaKOcPGp
 uatk6QMrggHp3Li+3yZrLBE0qPr/sNMVb7mUesdZb6lFd2VIs8siwhfeGXMS+nDI
 xePzsR43Fnn5Q5KIqqvcWUb+TTTqUDUff0wyAU8NBgCaIBIZK8h2ppS1jjnbms0I
 mr8Er2vb
 =Dfum
 -----END PGP SIGNATURE-----

Merge tag 'v2021.01-rc5' into next

Prepare v2021.01-rc5

Signed-off-by: Tom Rini <trini@konsulko.com>
2021-01-05 16:20:26 -05:00
Simon Glass
20e442ab2d dm: Rename U_BOOT_DEVICE() to U_BOOT_DRVINFO()
The current macro is a misnomer since it does not declare a device
directly. Instead, it declares driver_info record which U-Boot uses at
runtime to create a device.

The distinction seems somewhat minor most of the time, but is becomes
quite confusing when we actually want to declare a device, with
of-platdata. We are left trying to distinguish between a device which
isn't actually device, and a device that is (perhaps an 'instance'?)

It seems better to rename this macro to describe what it actually is. The
macros is not widely used, since boards should use devicetree to declare
devices.

Rename it to U_BOOT_DRVINFO(), which indicates clearly that this is
declaring a new driver_info record, not a device.

Signed-off-by: Simon Glass <sjg@chromium.org>
2021-01-05 12:26:35 -07:00
Igor Opaniuk
f23c706863 toradex: hand over maintainership
Hand over maintainership of Toradex SoMs (that I was responsible of) to
Oleksandr because of my resignation from Toradex, as such I will
have no immediate involvement with these modules and as a result not
able to continue maintaining these boards.

CC: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Acked-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-12-26 14:56:09 +01:00
Simon Glass
8a8d24bdf1 dm: treewide: Rename ..._platdata variables to just ..._plat
Try to maintain some consistency between these variables by using _plat as
a suffix for them.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:09 -07:00
Simon Glass
caa4daa2ae dm: treewide: Rename 'platdata' variables to just 'plat'
We use 'priv' for private data but often use 'platdata' for platform data.
We can't really use 'pdata' since that is ambiguous (it could mean private
or platform data).

Rename some of the latter variables to end with 'plat' for consistency.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-12-13 16:51:08 -07:00
Masahiro Yamada
b75d8dc564 treewide: convert bd_t to struct bd_info by coccinelle
The Linux coding style guide (Documentation/process/coding-style.rst)
clearly says:

  It's a **mistake** to use typedef for structures and pointers.

Besides, using typedef for structures is annoying when you try to make
headers self-contained.

Let's say you have the following function declaration in a header:

  void foo(bd_t *bd);

This is not self-contained since bd_t is not defined.

To tell the compiler what 'bd_t' is, you need to include <asm/u-boot.h>

  #include <asm/u-boot.h>
  void foo(bd_t *bd);

Then, the include direcective pulls in more bloat needlessly.

If you use 'struct bd_info' instead, it is enough to put a forward
declaration as follows:

  struct bd_info;
  void foo(struct bd_info *bd);

Right, typedef'ing bd_t is a mistake.

I used coccinelle to generate this commit.

The semantic patch that makes this change is as follows:

  <smpl>
  @@
  typedef bd_t;
  @@
  -bd_t
  +struct bd_info
  </smpl>

Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
2020-07-17 09:30:13 -04:00
Simon Glass
cd93d625fd common: Drop linux/bitops.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
c05ed00afb common: Drop linux/delay.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:23 -04:00
Simon Glass
0914011310 command: Remove the cmd_tbl_t typedef
We should not use typedefs in U-Boot. They cannot be used as forward
declarations which means that header files must include the full header to
access them.

Drop the typedef and rename the struct to remove the _s suffix which is
now not useful.

This requires quite a few header-file additions.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 18:36:55 -04:00
Simon Glass
4d72caa5b9 common: Drop image.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
90526e9fba common: Drop net.h from common header
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:31 -04:00
Philippe Schenker
f72e48ba4d board: apalis_imx6: Add KSZ9131 phy skew settings
This patch adds skew register settings for KSZ9131. It checks first
which phy is on the board and then applies the correct skew settings.

Skew settings calculation for the KSZ9131:
The i.MX6 SoC has an output skew tolerance of -100ps to 900ps. All
PCB traces where routed exactly the same length so we can calculate
the skew settings without taking the length into consideration. The
traces are all length matched.

RXC skew (PHY to MAC):
- We use the 2ns DLL controlled delay on the PHY
- We do not use the skew registers

This results in the following values:

		RXC
PHY fixed Delay	2000ps
PHY Added Delay	0ps
T_setup_R min	2.00ns
T_setup_R typ	2.00ns
T_setup_R max	2.00ns
T_hold_R min	1.60ns
T_hold_R typ	2.00ns
T_hold_R max	2.40ns

That means we are well within RGMII specs.

TXC skew (MAC to PHY):
- We use the 2ns DLL controlled delay on the PHY
- We then subtract ~0.6ns with TXD[0:3] and TXC clock pad skew
  register in a resulting ~1.4ns delay.

This results in the following values under consideration of the
tolerances:

		TXC min	TXC typ	TXC max
MAC min		-100ps	-100ps	-100ps
MAC max		900ps	900ps	900ps
PHY fixed Delay	2000ps	2000ps	2000ps
PHY added Delay	-340ps	-600ps	-859ps
T_setup_T min	1.56ns	1.30ns	1.04ns
T_setup_T typ	2.06ns	1.80ns	1.54ns
T_setup_T max	2.56ns	2.30ns	2.04ns
T_hold_T min	1.04ns	1.30ns	1.56ns
T_hold_T typ	1.94ns	2.20ns	2.46ns
T_hold_T max	2.84ns	3.10ns	3.36ns

This shows that T_hold_T min and T_setup_T min times are out of spec
for RGMII timing. However the KSZ9131 has a minimal value for this time
of 0.8ns which is met under all circumstances.

Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
2020-05-01 13:46:22 +02:00
Simon Glass
9a3b4ceb37 common: Move reset_cpu() to the CPU header
Move this function out of common.h and into a relevant header file.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-01-17 14:02:31 -05:00
Igor Opaniuk
a781ed271e apalis_imx6: migrate to DM_ETH
Migrate to DM_ETH and remove hardcoded pinmux configuration.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
2020-01-07 10:26:56 +01:00
Igor Opaniuk
b6ba18f414 MAINTAINERS: change apalis_imx6/colibri_imx6 maintainers
Take over maintainership for apalis_imx6 and colibri_imx6 modules.

Signed-off-by: Igor Opaniuk <igor.opaniuk@toradex.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2020-01-07 10:26:56 +01:00
Simon Glass
5255932f01 common: Move some board functions out of common.h
A number of board function belong in init.h with the others. Move them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:25:21 -05:00
Ricardo Salveti
536c564b91 apalis_imx6: fix broken fsl_esdhc_imx conversion
Commit e37ac717d7 ("Convert to use fsl_esdhc_imx for i.MX platforms")
converted FSL_ESDHC to FSL_ESDHC_IMX, but the config check for
apalis_imx6 wasn't updated accordantly.

Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-10-08 16:35:16 +02:00
Ricardo Salveti
6f8ef051c5 apalis_imx6: add board_fit_config_name_match to support FIT in SPL
Only one dtb is currently supported, so match with imx6-apalis.

Signed-off-by: Ricardo Salveti <ricardo@foundries.io>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Max Krummenacher <max.krummenacher@toradex.com>
2019-10-08 16:35:16 +02:00
Simon Glass
e7dcf5645f env: Drop environment.h header file where not needed
This header file is now only used by files that access internal
environment features. Drop it from various places where it is not needed.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Simon Glass
9fb625ce05 env: Move env_set() to env.h
Move env_set() over to the new header file.

Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Simon Glass <sjg@chromium.org>
2019-08-11 16:43:41 -04:00
Yangbo Lu
e37ac717d7 Convert to use fsl_esdhc_imx for i.MX platforms
Converted to use fsl_esdhc_imx for i.MX platforms.

Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Tested-by: Steffen Dirkwinkel <s.dirkwinkel@beckhoff.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Martyn Welch <martyn.welch@collabora.com>
Acked-by: Jason Liu <Jason.hui.liu@nxp.com>
2019-06-23 14:18:34 +08:00
Marek Vasut
64c751f635 ARM: imx: apalis_imx6: Drop ad-hoc SATA binding
Drop the ad-hoc AHCI binding code, this is superseded by
CONFIG_DWC_AHSATA_AHCI=y resp. drivers/ata/dwc_ahsata.c

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Stefan Agner <stefan.agner@toradex.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-06-11 10:42:48 +02:00
Gerard Salvatella
15c41a8d9e board: apalis_imx6: check for and report ecc errors in fuses
The PMIC on Apalis iMX6 may have ECC errors in fuses that will prevent
correct settings. Up to one bit error per fuse bank may be reported and
corrected by the ECC logic. Two bit errors can only be reported.

Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Stefan Agner
15834c6383 apalis_imx6: use SDP if USB serial downloader has been used
In case USB serial downloader has been used to load U-Boot start the
serial download protocol (SDP) emulation. This allows to download
complete images such as Toradex Easy Installer over USB SDP as well.
This code uses the boot ROM provided boot information to reliably
detect USB serial downloader.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Max Krummenacher
5135db4d8b apalis_imx6: revert fuse value set in mfgr_fuse
We have two commands to change the bootmode fuses:
mfgr_fuse which set fuse 0/5 and 0/6
and
updt_fuse which burns bit 4 of 0/5.

Before BSP 2.6 we fused in mfgr_fuse 0x5062, which boots
from the user partition of the eMMC.
To workaround certain hangs we moved to fastboot mode and
using the first bootpartition of the eMMC requiring a fuse
value of 0x5072 which could be achieved by the then added
updt_fuse command. At the same time the mfgr_fuse command
was changed to also fuse 0x5072, revert that second change
so that one can fuse both values, one with just mfgr_fuse
and the later with mfgr_fuse;updt_fuse.

Note that the mfgr_fuse command is only needed at module
production time, a customer might need to use updt_fuse
when upgrading an older module to be compatible with a
newer image. The command is integrated into the image
update scripts.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Stefan Agner <stefan.agner@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Max Krummenacher
389f61ef44 apalis_imx6: disable ri and dcd irq in uarts
If the UART is used in DTE mode the RI and DCD bits in UCR3 become
irq enable bits. Both are set to enabled after reset and both likely
are pending.

Disable the bits also on UARTs not used in the boot loader to prevent
an interrupt storm when Linux enables the UART interrupts.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
b4707a25d0 apalis_imx6: pf0100: reorder and cleanup message printing
Keep debug code at the end of the function.
Use a one line informational message for the PMIC only.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Max Krummenacher
3ef55a7473 apalis_imx6: unify sd/mmc drive strength with linux kernel settings
In the Linux device tree we use 40Ohm drive strength. So use the same
value in U-Boot.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
16959d75dd apalis_imx6: drop CONFIG_OF_SYSTEM_SETUP
This doesn't do anything anymore, probably never did.

Signed-off-by: Max Krummenacher <max.krummenacher@toradex.com>
Acked-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
9fb4b8929a apalis_imx6: migrate usb to using driver model
Migrate USB to using driver model.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
72b49e2c1e apalis_imx6: migrate mmc and sata to using driver model
Migrate MMC and SATA to using driver model.

While at it also enable SCSI driver model.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
ab92352d22 apalis_imx6: migrate i2c to using driver model
Migrate I2C to using driver model.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
5177087f64 apalis_imx6: clean-up and migrate gpios to using driver model
Migrate GPIOs to using driver model, properly request backlight,
Ethernet PHY reset, MMC/SD card detect and USB power GPIOs and also
enable SION bit in pin muxing for Apalis, backlight, eMMC reset,
Ethernet PHY reset and USB power enable GPIOs.

While at it also update copyright year, clean-up/re-order includes,
add some comments clarifying ifdef scope and do some White-space
clean-up.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
4df0292359 apalis_imx6: migrate to using device tree
Migrate to using device tree required for further driver model
integration.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Marcel Ziswiler
67ef14c72e apalis_imx6: get rid of obsolete nospl configurations
Now with SPL long since being in place even for recovery using SDP
finally get rid of those nospl configurations.

Signed-off-by: Marcel Ziswiler <marcel.ziswiler@toradex.com>
2019-04-13 20:30:08 +02:00
Gerard Salvatella
a3c9021771 board: toradex: turn off lcd backlight before OS handover
U-Boot typically tears down the display controller before handing
control over to Linux. On LCD displays disabling pixel clock leads to a
fading out effect with vertical/horizontal lines. Make sure to disable
back light before booting Linux.

Signed-off-by: Gerard Salvatella <gerard.salvatella@toradex.com>
Signed-off-by: Philippe Schenker <philippe.schenker@toradex.com>
Signed-off-by: Tom Warren <twarren@nvidia.com>
2019-02-20 09:01:45 -07:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00