This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Replaced misspelled words "parition"/"paritioning" (missing 't') in two
Kconfig files by correct words "partition"/"partitioning"
Signed-off-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Add a PHY driver for the R-Car Gen2 which allows configuring the mux
connected to the EHCI controllers and USBHS controller.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
The code fails to copy the last PHY phandle argument, so it is
missing from the adjusted phandle args and the consumer cannot
use it to determine what the PHY should do.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Add support for fetching the clock frequency both using the legacy
method in case clock framework is disabled as well as via the clock
framework if it is enabled. This allows for migration to the clock
framework on platforms which supports it while not breaking legacy
platforms. That said, the legacy method must be removed eventually.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add clock driver for the Arria10, which allows reading the clock
frequency from all the clock described in the DT. The driver also
allows enabling and disabling the clock. Reconfiguring frequency
is not supported thus far.
Since the DT bindings for the SoCFPGA clock are massively misdesigned
and the handoff DT adds additional incorrectly described entries to
the DT, the driver contains workarounds which attempt to rectify all
of those problems.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Add wrapper around the designware MAC driver to handle the SoCFPGA
specific configuration bits. On Arria10, this is configuration of
syscon phy_intf.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The recv variable in sandbox_tpm2_fill_buf() is a pointer on a pointer
of a char array. It means accessing *recv is the char array pointer
itself while **recv is the first character of that array. There is no
need for such indirection here, so simplify the code.
Simplifying things will make the last assignment right: "*recv = NULL"
is now correct. The issue has been found by the following Coverity
Scan report:
CID 183371: Incorrect expression (UNUSED_VALUE)
Assigning value "4UL" to "*recv" here, but that stored value is overwritten before it can be used.
232 *recv += sizeof(rc);
233
234 /* Add trailing \0 */
235 *recv = NULL;
While at simplifying things, use '\0' instead of NULL when adding an
empty char at the end of the buffer.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The second check on pcr_map in sandbox_tpm2_xfer() is wrong. It should
check for pcr_map not being empty. Instead, it is a pure copy/paste of
the first check which is redundant.
This has been found thanks to a Coverity Scan report:
CID 183370: Memory - illegal accesses (UNINIT)
Using uninitialized value "pcr_index".
put_unaligned_be32(tpm->pcr_extensions[pcr_index], recv);
This is because pcr_index is initialized only if the user input is
correct, ie. at least one valid bit is set in pcr_map.
Fix the second check and also initialize pcr_index to 0 (which is
harmless in case of error) to make Coverity Scan happy.
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In case the slow clock is not properly configured, the UTMI clock
cannot lock the PLL, because UPLLCOUNT will "wait X slow clock cycles".
In this case U-boot will loop indefinitely.
Added a timeout in this case, to start U-boot even if UTMI clock is
not enabled, so the user can use different media if needed, or investigate.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Add a driver for the Xilinx LogiCORE DisplayPort IP core, which is a
pure DP transmitter core for Xiling FPGA (no display capabilities).
Signed-off-by: Mario Six <mario.six@gdsys.cc>
The entries of Makefiles should be sorted, which is not the case in the
video driver Makefile.
Sort the entries alphabetically as far as this makes sense.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Add a uclass for AXI (Advanced eXtensible Interface) busses, and a
driver for the gdsys IHS AXI bus on IHS FPGAs.
Signed-off-by: Mario Six <mario.six@gdsys.cc>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is a fix made for the fsl_ifc_nand driver on linux kernel by
Pavel Machek and is applied to uboot. It is currently on applied on
linux-mtd.
https://patchwork.kernel.org/patch/9758117/
IFC always raises ECC errors on erased pages. It is only ignored when
the buffer is checked for all 0xFF by is_blank(). The problem is a
single bitflip will cause is_blank() and then mtd_read to fail. The fix
makes use of nand_check_erased_ecc_chunk() to check for empty pages
instead of is_blank(). This also makes sure that reads are made at ECC
page size granularity to get a proper bitflip count. If the number of
bitflips does not exceed the ECC strength, the page is considered empty
and the bitflips will be corrected when data is sent to the higher
layers (e.g. ubi).
Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Cc: Pavel Machek <pavel@denx.de>
Cc: Scott Wood <oss@buserror.net>
Acked-by: Pavel Machek <pavel@denx.de>
[Kurt: Replaced dev_err by printf due to compiler warnings]
Tested-by: Kurt Kanzenbach <kurt@linutronix.de>
Signed-off-by: Kurt Kanzenbach <kurt@linutronix.de>
Reviewed-by: York Sun <york.sun@nxp.com>
Add support for ICID setting of qman portals and the required device
tree fixups. Also fix an endiness issue in portal setup code.
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
QMAN_BAR{E} register setup was disabled on ARM platforms, however the
register does need to be set. Enable the code also on ARMs and fix the
CONFIG_SYS_QMAN_MEM_PHYS define to the correct value so that the newly
enabled code works.
Reviewed-by: Bharat Bhushan <bharat.bhushan@nxp.com>
Signed-off-by: Laurentiu Tudor <laurentiu.tudor@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
This patch save common LED property "default-state" value
in post bind of LED uclass.
The configuration for this default state is only performed when
led_default_state() is called;
It can be called in your board_init()
or it could added in init_sequence_r[] in future.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This reverts commit bc882f5d5c.
because this patch adds the probe of LED driver during the
binding phasis. It is not allowed in driver model because
the drivers (clock, pincontrol) needed by the LED driver can
be also probed before the binding of all the device and
it is a source of problems.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
sourcing of sub directiory kconfig files are not in
proper order, so keep them in ascending order.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>
It might be useful for user to see some human-readable root cause
message in addition to "configuration failed" message, so that the issue
can be fixed quickly.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
In case of error in dfu_init_env_entities(), env_bkp will leak. Fix it
by providing single return path.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Commit 5d8fae7916 ("dfu: avoid memory leak") brings a regression which
described below. This patch is effectively reverting that commit, adding
corresponding comment to avoid such regressions in future.
In case of error in dfu_config_entities(), it frees "dfu" array, which
leads to "data abort" in dfu_free_entities(), which tries to free the
same array (and even tries to access it from linked list first). The
issue occurs e.g. when partition table on device does not match
$dfu_alt_info layout:
=> dfu 0 mmc 1
Couldn't find part #2 on mmc device #1
DFU entities configuration failed!
data abort
To fix this issue, do not free "dfu" array in dfu_config_entities(). It
will be freed later in dfu_free_entities().
Tested on BeagleBone Black (where this regression was originally found).
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
As well as in K_FW_LBA_READ_10 and K_FW_LBA_ERASE_10 take device's
block size from f_rkusb->desc->blksz instead of the fixed 512 bytes.
Keep original behaviour of retry probing assigned block device on
every host request to manage late SDCard plugs.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
While downloading or uploading megabytes of data we had thousands of
printf in console like:
transfer 0x10000 bytes done
OR
Uploading 0x1000 bytes
This because transfers are chunked and there is no way on target
side to know the overall transfer size (to print one string per
overall transfer).
All these prints on serial console do slow down significantly the
transfer and does not offer a significant information to the
developer: rkdeveloptool and Rockchip original tool do use small
chunks read/writes on big transfers. This allows on workstation
to print percentage of transfer complete and as well offers to
developer the information about: transfer is running OK.
On error, either the percentage will stop or an error will be shown
on workstation console.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
This command is part of the write partition sequence performed by
rkdeveloptool: one partition is first completely erased and
than wrote.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch implement reading blocks form selected device with
LBA addressing.
Corresponding command on workstation is:
rkdeveloptool rl <start_blk> <blk_cnt> <file>
While we support reading more than one blocks per K_FW_LBA_READ_10
request, rkdeveloptool and original rockchip tool do perform
chunk reads limiting the maximum size per chunk far lower
than max int values.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Chip Version is a string saved in BOOTROM address space Little Endian.
Ex for rk3288: 0x33323041 0x32303134 0x30383133 0x56323030
which brings: 320A20140813V200
Note that memory version do invert MSB/LSB so printing the char
buffer would show: A02341023180002V
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
Two consecutive rockusb_tx_write without waiting for request complete
do results in transfer reset of first request and thus no or incomplete
data transfer. This because rockusb_tx_write do use just one USB request
to keep serialization.
So calls like:
rockusb_tx_write_str(emmc_id);
rockusb_tx_write_csw(cbw->tag, cbw->data_transfer_length, CSW_GOOD);
was succeeding only when DEBUG was defined because the time spent
printing debug info was enough for transfer to complete.
This patch fixes the issue adding a simple request complete handler
called rockusb_tx_write_csw to be set as complete handler of in_req
when sending back simple payload + CSW replies to commands.
This new handler will always send CSW_GOOD replies because in case
of error the command callback itself must send back an error CSW as
unique reply to command.
This patch fixes execution of:
$ rkdeveloptool rfi
when DEBUG is not defined.
Signed-off-by: Alberto Panizzo <alberto@amarulasolutions.com>
After the commit 6aae84769a ("gadget: f_thor: Fix memory leaks of
usb request and its buffer"), there is hang-up with ctrl-c in some
udc. It is because req of out_ep is freed before out_ep is disabled.
Fix hang-up with ctrl-c by disabling ep before free req of the ep.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
The ethernet name should be within the ETH_NAME_LEN, as this
is the buffer space allocated to ethernet name.
Otherwise, this causes buffer overflow.
Reported-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Most FSL PCIe controllers expects 333 MHz PCI reference clock.
This clock is derived from the CCB but in many cases the ref.
clock is not 333 MHz and a divisor needs to be configured.
This adds PEX_CCB_DIV #define which can be defined for each
type of CPU/platform.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Add several PCI capability and extended capability ID registers
in the swap_case driver, so that we can add test case for
dm_pci_find_capability() and dm_pci_find_ext_capability().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This introduces two new APIs dm_pci_find_capability() and
dm_pci_find_ext_capability() to get PCI capability address and
PCI express extended capability address for a given PCI device.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We have "struct sandbox_pci_priv" in pci_sandbox driver. To avoid
confusion, rename the emul's priv to "struct sandbox_pci_emul_priv".
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds a U_BOOT_PCI_DEVICE() declaration to the swap_case driver.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
At present all emulated sandbox pci devices must be present in the
device tree in order to be used. The real world pci uclass driver
supports pci device driver matching, and we should add such support
on sandbox too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The correct driver data comes from the matching 'id' instead of
'find_id' in pci_find_and_bind_driver().
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the newly added test cases for PCI configuration access, we get:
=> ut dm pci_busdev
Test: dm_test_pci_busdev: pci.c
test/dm/pci.c:49, dm_test_pci_busdev(): SANDBOX_PCI_VENDOR_ID == vendor:
Expected 4660, got 65535
Test: dm_test_pci_busdev: pci.c (flat tree)
test/dm/pci.c:49, dm_test_pci_busdev(): SANDBOX_PCI_VENDOR_ID == vendor:
Expected 4660, got 65535
Failures: 2
The bug only shows up when bus number is not equal to zero. This is
caused by the plain find_devfn parameter is passed to function call
pci_bus_find_devfn(), inside which find_devfn is compared to devfn
in the device's pplat structure. However pplat->devfn does not carry
the bus number. Fix this by passing find_devfn with bus number masked.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With the newly added testing of more than one device, we get:
=> ut dm pci_swapcase
Test: dm_test_pci_swapcase: pci.c
test/dm/pci.c:88, dm_test_pci_swapcase(): "tHIS IS A tESt" = ptr:
Expected "tHIS IS A tESt", got "this is a test"
Test: dm_test_pci_swapcase: pci.c (flat tree)
test/dm/pci.c:88, dm_test_pci_swapcase(): "tHIS IS A tESt" = ptr:
Expected "tHIS IS A tESt", got "this is a test"
Failures: 2
The failure only happens on the 2nd swap_case device on the PCI bus.
The case passes on the 1st device.
It turns out the swap_case driver does not emulate bit#0 in BAR
registers as a read-only bit. This corrects the implementation.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The flag to control whether to scan multi-function device during
enumeration should be cleared at the beginning of each iteration
if the device's function number equals to zero.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Currently only devfn is extracted in child_post_bind(). Now that
we have the live-tree version API to look up PCI vendor and device
id from the compatible string, let's extract and save them too.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't have the live-tree version of fdtdec_get_pci_vendev().
This adds the API.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This adds the initial support of the Broadcom BCM6838 SoC familly,
only cpu, dram, uart and leds are supported.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
This adds an option to force the size of the ram, and
avoid the detection of ram size.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
The only platform left for the AU1x00 SoCs was the pb1x00 platform, an
apparent clone of the dbau1x00 platform. As pb1x00 had no listed
maintainer I am assuming that it is also orphaned. Remove this platform
and then remove the unused SoC support.
Cc: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Add support for reading label property from DT and set up bank name
based on that. If label property is not present full device node name is
used.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
.set_value functions have no specified return value and gpio_uclass is
not working with it too. But this patch is returning 0 to be in sync
with others DM gpio drivers.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Reading registers for finding out output value is not working because
input value is read instead in case of tristate.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
There is no reason to do read/write for if/else separately.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Set a value before changing gpio direction. This will ensure that the
old value is not propagated when direction has changed but new value is
not written yet.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Call xilinx_gpio_get_bank_pin() before use.
Reported-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Stefan Herbrechtsmeier <stefan@herbrechtsmeier.net>
Add the PCA9646 support, which is 2-wire bus switch and buffered 4-channel.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
Add CONFIG_SPL_POWER_DOMAIN config entry.
Build drivers/power/domain if this config is selected.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch used platdata structure instead of priv for storing static
information read from DT.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit enables support for Exynos Designware MMC driver based on DM.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
By convention for DM_MMC the host->priv is used to store struct udevice
*dev pointer.
Unfortunately, the legacy Exynos DW MMC code uses this field to
store pointer to dwmci_exynos_priv_data struct
Hence, we do need to get data in other way - namely by using container_of
when host pointer is present.
In this way the sdr_timing data is properly accessed.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
This commit prevents memory leak when this function is used with DM_MMC
as the struct dwmci_exynos_priv_data is already allocated by DM.
It is necessary for NON DM aware devices to allocate this struct first.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
The Assigned Clock parents and rates misses the fact that a "0" entry can
be passed to skip setting a parent or rate of an assigned clock as
described in the Linux clock bindings at [1].
This patch simply skips the clock reparenting if the DT parsing returns
-ENOENT and the clock rate setting if "0" is passed as clock rate.
[1] https://github.com/torvalds/linux/blob/master/Documentation/devicetree/bindings/clock/clock-bindings.txt#L135
Fixes: f4fcba5c5b "clk: implement clk_set_defaults()"
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As platform uses GPIOs for card detection, it's
simpler and more readable to use GPIO_ACTIVE_(LOW|HIGH)
in the gpio flags instead of using the cd-inverted
property.
Reported-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Add missing clk_free() call in case of failure
when enabling the clock.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Config flag CONFIG_BLK becomes mandatory, update arm_pl180_mmci
to support this config.
This driver is used by STM32Fx and by Vexpress platforms.
Only STM32Fx are DM ready. No DM code is isolated and will be
removed easily when wexpress will be converted to DM.
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
1947c2d2a0 introduces cache line flushes for the bootcounter, but if
the start address is not aligned then the flush causes warnings of
the form:
CACHE: Misaligned operation at range [4030b7fc, 4030b83c]
Align both the start and end of the buffer (possibly crossing multiple
lines).
Fixes: 1947c2d2a0 ("bootcount: flush after storing the bootcounter")
Signed-off-by: Alex Kiernan <alex.kiernan@gmail.com>
Acked-by: Stefano Babic <sbabic@denx.de>
This patch adds support for STMicroelectronics STM32 ADC (analog to
digital converter). It's originally based on Linux kernel v4.18-rcs
drivers/iio/adc/stm32-adc*. It's composed of:
- core driver (UCLASS_SIMPLE_BUS) manages common resources (clk, regu).
- child drivers (UCLASS_ADC) declare each ADC, channels and handle
conversions.
This driver currently supports STM32H7 and STM32MP1 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
device_get_supply_regulator() only needs to be called once.
But each time there's call to adc_vxx_value() for instance, it calls
adc_vxx_platdata_update() -> device_get_supply_regulator().
So, move device_get_supply_regulator() to pre_probe() routine.
This also allows vdd_supply/vss_supply to be provided directly from
uc_pdata, e.g dt-binding variant like stm32-adc provide its own
'vref-supply'.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add clk_valid() to check for optional clocks are valid.
Call clk_valid() in test/dm/clk.c and add relevant test routine to
sandbox clk tests.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add spi driver for sun4i, sun5i and sun7i SoCs. The driver is
adapted from mailine kernel.
Signed-off-by: Stefan Mavrodiev <stefan@olimex.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This matches the compatible string used by the Linux kernel. This will
allow u-boot to use the same device tree files.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
[jagan: use armada instead of orion on .data]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Get the is_errata_50mhz_ac in .ofdata_to_platdata, and
reuse it in .set_mode this can eventually initialized
dt code at once and adding room to add platdata.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Add support for SPANSION s25fl128l
Signed-off-by: Clément Laigle <c.laigle@catie.fr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
[jagan: fixed , at the end of } ]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Drop the DM_I2C dependency, as the library only implements
the parsing of EDID data and doesn't depend on any driver
One user of this library, the i2c command, implements
support for legacy and DM I2C drivers
Tested on a Zynq board, whose I2C driver is not ported
yet to DM
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Return the error code of the set_features function only if
the error code is not ENOTSUPP. Otherwise, if this function
is not supported, it will return and fail to initialize the
NAND.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Convert the EINVAL error into ENOTSUPP when the GET/SET_FEATURES
is not supported.
Signed-off-by: Mylène Josserand <mylene.josserand@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
Only H3 and H5 have 4 PHYS so restrict rst_mask only for them
by checking PHY id as 3 and update the proper bits.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
usb_clk_cfg is setting CTRL_PHYGATE bit value in probe
which is BIT 0 for sun4i, 6i and 8 for a83t but all
these were handling in phy ops init exit calls.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
On newer Allwinner SoC, there is a pair of EHCI/OHCI USB hosts
for OTG host mode. USB PHY passby must be configured for its
corresponding PHY. so we can call for PHY#0. on the other hand
in past usb-phy code the same thing can be restricted for
Lower SoC's, other than H3/H5/A64.
Now there is no need to restrict usb passby since the phy driver
is DT enabled, and the respective phy calls will trigger based
DT information initiated by the drivers.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
Sometimes when a monitor without EDID information is plugged, the DE2
won't be probed (because of lack of timing information), but the HDMI
node is probed, thus a SimpleFB node with invalid information will be
populated.
Also detect whether DE2 is probed when creating SimpleFB node.
Fixes: be5b96f0e4 ("sunxi: setup simplefb for Allwinner DE2")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Jagan Teki <jagan@openedev.com>
The Allwinner H6 SoC has 3 MMC controllers like the ones in A64, with
the MMC2 come with the capability to do crypto by EMCE.
Add MMC support for H6. EMCE support is not added yet.
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
CREG GPIO is a driver for weird soc-specific output ports, which are
controlled by some fields in memory mapped register.
Example:
31 9 7 5 0 < bit number
| | | | |
[ not used | gpio-1 | gpio-0 | <-shift-> ] < 32 bit register
^ ^
| |
write 0x2 == set output to "1" (activate)
write 0x3 == set output to "0" (deactivate)
As of tooday we only support fixed (hardcoded) bit per gpio line,
activate / deactivatei and shift values. Fix that by read them from
device tree to be able to use this driver for other boards.
Remove "hsdk" prefix from compatible string as this driver can be
used with different boards like HSDK, AXS101, AXS103, etc.
Signed-off-by: Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=ePTT
-----END PGP SIGNATURE-----
Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot
Patch queue for efi - 2018-07-25
Highlights this time:
- Many small fixes to improve spec compatibility (found by SCT)
- Almost enough to run with sandbox target
- GetTime() improvements
- Enable EFI_LOADER and HYP entry on ARMv7 with NONSEC=y
Remove additional trailing whitespaces in prompt reported by kconfiglib:
warning: DM_PMIC_SANDBOX (defined at drivers/power/pmic/Kconfig:133) has
leading or trailing whitespace in its prompt
warning: <choice> (defined at dts/Kconfig:204) has leading or trailing
whitespace in its prompt
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Felix Brack <fb@ltec.ch>
The driver sets the weekday incorrectly when called by the
'date set' command.
Sunday is 1, Saturday is 7 unlike in U-Boot (see data sheet
https://www.nxp.com/docs/en/data-sheet/MC146818.pdf, table 3).
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
TPM_V1 was already compiled by default. Now that both can be compiled
at the same time, compiled them both by default.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
While there is probably no reason to do so in a real life situation, it
will allow to compile test both stacks with the same sandbox defconfig.
As we cannot define two 'tpm' commands at the same time, the command for
TPM v1 is still called 'tpm' and the one for TPM v2 'tpm2'. While this
is the exact command name that must be written into eg. test files, any
user already using the TPM v2 stack can continue to do so by just writing
'tpm' because as long as TPM v1 support is not compiled, U-Boot prompt
will search for the closest command named after 'tpm'.
The command set can also be changed at runtime (not supported yet, but
ready to be), but as one can compile only either one stack or the other,
there is still one spot in the code where conditionals are used: to
retrieve the v1 or v2 command set.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
[trini: In sandbox_tpm2_fill_buf() use NULL not \0 to ensure NULL
terminated string due to LLVM warning]
Signed-off-by: Tom Rini <trini@konsulko.com>
The TPM_DRIVER_SELECTED symbol was used in one of the initial series
about TPMv2 but its use has been dropped, making these selects
useless, remove them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
When Sandbox and the TPM stack are both selected, compile Sandbox TPM
driver by default.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch updates the zynq gem driver to support livetree.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Now zynq_gem driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Now CPSW driver will overwrite UCLASS_ETH node when PHY is
connected and configured which is not correct.
Use struct phydev->node instead.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use PHY API phy_get_ofnode() helper to get PHY DT node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Use PHY API phy_get_ofnode() helper to get PHY DT node.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Now the UCLASS_ETH device "node" field is owerwritten by some network drivers in
case of Ethernet PHYs which are linked to UCLASS_ETH device using
"phy-handle" DT property and when Ethernet PHY driver needs to read some
additional information from DT. In such cases following happens (in
general):
- network drivers
priv->phydev = phy_connect(priv->bus, priv->phyaddr, dev,
priv->interface);
<-- phydev is connected to dev which is UCLASS_ETH device
if (priv->phy_of_handle > 0)
dev_set_of_offset(priv->phydev->dev, priv->phy_of_handle);
<-- phydev->dev->node is overwritten by phy-handle DT node
- PHY driver in .config() callback
int node = dev_of_offset(dev);
<-- PHY driver uses overwritten dev->node
const void *fdt = gd->fdt_blob;
if (fdtdec_get_bool(fdt, node, "property"))
...
As result, UCLASS_ETH device can't be used any more for DT accessing.
This patch adds additional ofnode node field to struct phy_device which can
be set explicitly by network drivers and used by PHY drivers, so
overwriting can be avoided. Also add helper function phy_get_ofnode()
which will check and return phy_device->node or dev_ofnode(phydev->dev) for
backward compatibility with existing drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
We want to be able to include some other system headers in phy.h but
that requires us to have included common.h in the top-level first.
Also, common.h includes config.h as the first thing it does, so don't
include it directly.
Series-to: u-boot
Series-cc: Grygorii Strashko <grygorii.strashko@ti.com>
Seried-cc: ti
Series-process-log: sort, uniq
Cover-letter:
Prepare for net: phy: prevent uclass_eth device "node" field overwriting
Prepare for [1] so that it doesn't break the build for a bunch of
boards. There are a number of reasons this series broke the build
but none of them depend on changes in the series, so fix up those
situations ahead of applying that series.
[1] https://patchwork.ozlabs.org/cover/940104/
END
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Switch to use more generic ofnode API instead of FDT API.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
The data manual for DP83867IR/CR, SNLS484E[1], revised march 2017,
advises that strapping RX_DV/RX_CTRL pin in mode 1 and 2 is not
supported (see note below Table 5 (4-Level Strap Pins)).
It further advises that if a board has this pin strapped in mode 1 and
mode 2, then bit[7] of Configuration Register 4 (address 0x0031) must
be cleared to 0. This is to ensure proper operation of PHY.
Since it is not possible to detect in software if RX_DV/RX_CTRL pin is
incorrectly strapped, add a device-tree property to advertise this and
allow corrective action in software.
[1] http://www.ti.com/lit/ds/snls484e/snls484e.pdf
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Tested-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Add driver model support to the mvgbe driver. As a temporary measure
both DM and non-DM uses are supported. Once all the users have been
converted the non-DM support can be dropped.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Extract some function bodies to helper functions that can be reused in
the DM/non-DM implementations.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Ask the OS for each of its interfaces and for each one, bind a U-Boot
device and then probe it. This will allocate the priv data structure
that is then populated.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
We don't necessarily know how many MAC addresses we'll need, so implement
a ROM read so we always have something valid.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
With systemd stable interface names, eth0 will almost never exist.
Instead of using that name in the sandbox.dts, use an index.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Instead of doing a simple string compare against "lo", look for the flag
that indicates a localhost interface.
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
In raw mode, handle ctrl-c as normal. This allows normal ctrl-c behavior
such as aborting a command that is timing out without completely
terminating the sandbox executable.
In [1], Simon disabled this. His reason for it was that it interferes
with piping test scripts. Piping should be done in cooked mode, so this
change should still not interfere.
[1] commit 8969ea3e9f ("sandbox: Disable Ctrl-C")
Signed-off-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Pass an empty buffer instead of NULL if the hwconfig environment
variable isn't set.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: York Sun <york.sun@nxp.com>
Reviewed-by: York Sun <york.sun@nxp.com>
Make the code structure more general so that more socs can be
added easily and also remove speed limitation restriction.
Add the ls1012a sata support as well.
Signed-off-by: Tang Yuantian <andy.tang@nxp.com>
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Michal Simek <michal.simek@xilinx.com>
(with and without CONFIG_OF_LIVE on zynqmp zcu102)
Reviewed-by: York Sun <york.sun@nxp.com>
The EFI subsystem accesses the real time clock and is enabled by default.
So we should drop any CONFIG_CMD_DATE dependency from the real time clock
drivers.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
The NAND framework makes sure to pass in the buffer with at least
chip->buf_align alignment. Currently, the Denali NAND driver only
requests 16 byte alignment. This causes unaligned cache operations
for the DMA transfer.
[Error Example]
=> nand read 81000010 0 1000
NAND read: device 0 offset 0x0, size 0x1000
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
CACHE: Misaligned operation at range [81000010, 81001010]
4096 bytes read: OK
Reported-by: Marek Vasut <marex@denx.de>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
rtc_to_tm() and rtc_mktime() are required for some RTC drivers, at least
PL031. Without this patch, we also need to enable CONFIG_CMD_DATE even if
we don't want or need this command.
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Assigning a parameter which is not used afterwards has not effect.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add the missing gpio phy reset binding to the gpio and
reset time configuration
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This code is useful for testing the existance of devices that
do not have card detect capabilities. This breaks out the core
functionality and leaves the actual init logic and error reporting
in mmc_start_init().
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefano Babic <sbabic@denx.de>
If the bootcounter address is in a cached memory,
a flush of dcache must occur after updateing the bootcounter.
Issue found on i.MX6 where bootcounter is put into the internal
(cached) IRAM.
Signed-off-by: Stefano Babic <sbabic@denx.de>
rk3066 and rk3188 has two I2C controller implementations.
Current I2C driver wan't work with legacy implementation.
Switching between controllers is performed using a bit inside
GFR_SOC_CON1 register. The bit setting is performed by pinctrl
driver. The patch ask pinctrl to do settings.
Signed-off-by: Alexander Kochetkov <al.kochet@gmail.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
[fix warnings by including the rk3228 variant in the compatible-list]:
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
HSE and LSE bypass shall support both analog and digital signals.
This patch add a way to select digital bypas case in the device tree
and set the associated bit DIGBYP in RCC_BDCR and RCC_OCEN register
during clock tree initialization.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Add ADC clock gating, that may be used by STM32 ADC.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
This patch add clk_enable/clk_disable/clk_get_rate support for
- DSI_PX
- LTDC_PX
- DSI_K (only get rate)
These clocks are needed for LTDC and DSI drivers with latest device tree.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
the function compute the VCO PLL freq, used in
- stm32mp1_read_pll_freq()
- pll_set_rate()
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
# Conflicts:
# drivers/clk/clk_stm32mp1.c
This patch define RCC_PLLNCFGR2_SHIFT to reuse it in
the pll function for set rate.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Reviewed-by: Vikas Manocha <vikas.manocha@st.com>
Following next kernel rcc bindings, we must use a MFD
RCC driver which is able to bind both clock and reset
drivers.
We can reuse and adapt RCC MFD driver already available
for MCU SoCs (F4/F7/H7).
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Use new API syscon_node_to_regmap in sysreset_syscon driver
for compatible "syscon-reboot"; that's avoid the need of explicit
syscon binding for "regmap" handle.
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
For qemu-x86 the date command produces wrong days of the week:
Date: 2018-07-06 (Saturday) Time: 18:02:03
Date: 2018-07-07 (unknown day) Time: 21:02:06
According to a comment in the Linux driver the mc146818 only updates the
day of the week if the register value is non-zero.
Sunday is 1, saturday is 7 unlike in U-Boot (see data sheet
https://www.nxp.com/docs/en/data-sheet/MC146818.pdf).
So let's use our library function to determine the day of the week.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Our implementation of rtc_to_tm() cannot handle dates of more than
0x7fffffff seconds after 1970-01-01.
Adopt the Linux kernel implementation.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors in a Qualcomm platform.
Adapted from the Linux driver (4.17)
Changes from the original Linux driver:
* Removed HW spinlock mechanism, which is irrelevant
in U-boot particualar use case, which is just reading from the smem.
* Adapted from Linux driver model to U-Boot's.
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This is a uclass for Shared memory manager drivers.
A Shared Memory Manager driver implements an interface for allocating
and accessing items in the memory area shared among all of the
processors.
Signed-off-by: Ramon Fried <ramon.fried@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
QEMU provides an emulated ARM AMBA PrimeCell PL031 RTC.
The patch sets the base address in the board include file according to the
definition in hw/arm/virt.c of the QEMU source. It defines the Kconfig
option for the existing driver, and enables the RTC driver in
qemu_arm64_defconfig and qemu_arm_defconfig as well as the date command.
We need an RTC to provide the GetTime() runtime service in the UEFI
subsystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Tested-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>
Signed-off-by: AKASHI Takahiro <takahiro.akashi@linaro.org>
This patch adds a delay when regulators are disabled.
This delay is set to 5 ms to cover all use cases.
The worst use case actually seen is during a SD card power cycle.
Signed-off-by: Christophe Kerello <christophe.kerello@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
In case of phy are provided from a PHY provider nodes as following:
usbphyc: usb-phy@5a006000 {
compatible = "st,stm32mp1-usbphyc";
reg = <0x5a006000 0x1000>;
clocks = <&rcc_clk USBPHY_K>;
resets = <&rcc_rst USBPHY_R>;
#address-cells = <1>;
#size-cells = <0>;
usbphyc_port0: usb-phy@0 {
reg = <0>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <0>;
};
usbphyc_port1: usb-phy@1 {
reg = <1>;
phy-supply = <&vdd_usb>;
vdda1v1-supply = <®11>;
vdda1v8-supply = <®18>
#phy-cells = <1>;
};
};
and PHY are called as following:
usbh_ehci: usbh-ehci@5800d000 {
compatible = "generic-ehci";
reg = <0x5800d000 0x1000>;
clocks = <&rcc_clk USBH>;
resets = <&rcc_rst USBH_R>;
interrupts = <GIC_SPI 75 IRQ_TYPE_NONE>;
companion = <&usbh_ohci>;
phys = <&usbphyc_port0>;
phy-names = "usb";
status = "okay";
};
generic_phy_get_by_index() must be updated to first look for
PHY phandle as previously and in case of error looks for PHY
provider by finding the parent's current node which is the PHY
provider.
args (ofnode_phandle_args struct) must also be updated by inserting
the phy index into the PHY provider as args[0].
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Correctly manage the SDMMC reset and card cycle power
to fully handle the power cycle added in the MMC uclass
and avoid issue with level-shifter with some uSDCARD.
3 states managed in driver:
1/ reset: SDMMC disable, signal HiZ
2/ power-cycle: SDMMC disable, signals drive to 0
3/ power-on: SDMMC enabled
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Disable the use of function zynq_loadfs when compiling
the driver for the SPL, as the following filesystem
functions are not found by the linker:
- fs_set_blk_dev
- fs_read
- fs_set_blk_dev
- fs_read
- fs_read
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Watchdog can be started before probe and u-boot should just take control
over it. That's why do not stop watchdog in probe to cover cases where
watchdog can expire before probe and start.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
IP itself has no reg/no bit which can be used for this functionality.
Add this note to the driver to make sure that none will be asking for
that. Current method is to setup 1s timeout and hang() which is done via
wdt_expire_now().
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.
GPIO reset is handled via sysreset with adding this fragment to DT.
gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};
hard-reset-gpio property is not documented and also handled.
Conversion is required.
Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Xilinx Axi wdt driver conversion to driver model & Kconfig update
for the same.
Signed-off-by: Shreenidhi Shedi <yesshedi@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This patch is enabling GPIO_DM support to have an option to use this
driver together with zynq gpio driver.
!DM part is kept there till Microblaze is cleanup which will be done
hopefully soon.
Just a note:
There is no reason to initialize uc-priv->name because it is completely
unused.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Microblaze is storing reset vector at address 0x0.
It means soft reset can be done by just jumping to this address.
This code was in platform code but sysreset interface is providing
enough capabilities to have more options how to reset the system. It can
go from gpio reset through watchdog reset till soft reset.
The driver has not compatible string because this is cpu specific and DM
core is not able to detect compatible string in DT root that's why this
driver will be instantiated from platform code by calling
device_bind_driver(gd->dm_root, "mb_soft_reset", "reset_soft",
NULL);
It should be bind as the last reset method to ensure that hw reset is
called before this.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The Linux kernel has binding for gpio-restart node.
This patch is adding basic support without supporting any optional
properties.
This driver was tested on Microblaze system where gpio is connected to
SoC reset logic.
Output value is handled via gpios cells values.
In gpio_reboot_request() set_value is writing 1 because
dm_gpio_set_value() is capable to changing it when it is ACTIVE_LOW.
...
if (desc->flags & GPIOD_ACTIVE_LOW)
value = !value;
...
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
There should be proper bank name setup to distinguish between different
gpio drivers. Use dev->name for it.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove bogus zynq_gpio_getplat_data() and read driver data directly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate gpio ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate sysreset ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Relocate watchdog ops as was done by:
"dm: Add support for all targets which requires MANUAL_RELOC"
(sha1: 484fdf5ba0)
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
uclass name is used by dev_read_alias_seq which return seq number when
aliases are used.
Code fragment:
168 int dev_read_alias_seq(struct udevice *dev, int *devnump)
169 {
170 ofnode node = dev_ofnode(dev);
171 const char *uc_name = dev->uclass->uc_drv->name;
172 int ret;
173
174 if (ofnode_is_np(node)) {
175 ret = of_alias_get_id(ofnode_to_np(node), uc_name);
Also this patch enables DM_UC_FLAG_SEQ_ALIAS to be in sync with Linux
which is also using watchdog name for watchdog aliases.
drivers/watchdog/watchdog_core.c:215:
ret = of_alias_get_id(wdd->parent->of_node, "watchdog");
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch basically adds two new commands for loadig secure
images.
1. zynq rsa adds support to load secure image which can be both
authenticated or encrypted or both authenticated and encrypted
image in xilinx bootimage(BOOT.bin) format.
2. zynq aes command adds support to decrypt and load encrypted
image back to DDR as per destination address. The image has
to be encrypted using xilinx bootgen tool and to get only the
encrypted image from tool use -split option while invoking
bootgen.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Explanation from Simon Glass
"Private data is created when the device is probed and freed when the
device is removed.
Platform data is created when the device is bound, and survives
probe/remove cycles.
Strictly speaking, platform data should be used to hold the decoded
device tree properties. Private data should be used for run-time
things the device needs to keep track of."
Based on description the driver needs to be switch to use platdata
instead of priv.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This patch fixed the same if/else part error by adding the required
source select on the basis of is_pre_src check.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
This commit adds paired dev info for winbond w25q16jv
(tested w25q16jvssiq with a i.mx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Macronix mx25l1633e nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the Gigadevice gd25q16c nor flash. (Tested on a imx6 board)
Signed-off-by: Ludwig Zenz <lzenz@dh-electronics.de>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This commit adds the following flashes to the id-table
- W25Q16JV
- W25Q32JV
- W25Q64JV
- W25Q128JV
- W25Q256JV
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch adds qspi driver support for ZynqMP SoC. This
driver is responsible for communicating with qspi flash
devices.
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
[jagan: removed GQSPI_MIO_NUM_ macros]
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch is for the startup block issue in the spi controller.
SPI clock is passing through STARTUP block to FLASH. STARTUP block
don't provide clock as soon as QSPI provides command. So, first
command fails.
This patch added support to read JEDEC id in xilinx_spi_xfer ().
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch modify xilinx_spi_xfer() function and add rxfifo() and
txfifo() functions to add the modularity so that these functions
can be used by other functions within the same file.
This patch also added support to read fifo_size from dts.
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch added support to read register base address from DTS file.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Add support for the GMAC found in the Allwinner R40/V40 SoC.
The R40 GMAC interface is not controlled by the syscon register but
has a separate configuration register in the CCU.
The clock gate and reset bits are in a different register compared
to the other SoCs supported by this driver.
The driver uses the -gmac suffix for the R40 because the R40 also
has a different 100 MBit MAC (EMAC).
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Use driver data->variant information to select device specific
pin mux and phy clock settings.
Suggested by Jagan Teki
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
If the variant is not set and therefore NULL, do not attempt to print
the variant.
Signed-off-by: Lothar Felten <lothar.felten@gmail.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@openedev.com>
Commit dd27918c22 ("dm: mmc: sunxi: Add support for driver model")
only added the allwinner,sun5i-a13-mmc compatible string for this
driver. The DM initialisation code here also works with (at least) A10
and A20, so add the appropriate compatible strings as per Linux 4.17's
driver.
Tested on A10 Cubieboard and A20 pcDuino3 Nano with CONFIG_DM_MMC.
(A20 worked already, because sun7i-a20.dtsi specifies both the A13 and
A20 strings.)
Signed-off-by: Adam Sampson <ats@offog.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jteki@openedev.com>
When doing "i2c dev 4; i2c probe" with ENET daughter card connected
on iMX8QXP MEK board, we met a i2c bus busy issue, that the BBF of
lpi2c always show busy, but the master is idle, and stop is detected
(SDF set).
This patch addes a handling to re-init the lpi2c master for this
case. Then the issue can be worked around.
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
In xfer function, both bus_i2c_read and bus_i2c_write will
send a STOP command. This causes a problem when reading register
data from i2c device.
Generally two operations comprise the register data reading:
1. Write the register address to i2c device.
START | chip_addr | W | ACK | register_addr | ACK |
2. Read the Data from i2c device.
START | chip_addr | R | ACK | DATA | NACK | STOP
The STOP command should happen at the end of the transfer, otherwise
we will always get data from register address 0
Signed-off-by: Ye Li <ye.li@nxp.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
For LPI2C IP, NACK is detected by the rising edge of the ninth clock.
In current uboot driver, once NACK is detected, it will reset and then
disable LPI2C master. As a result, we can never see the falling edge
of the ninth clock.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Add compatible string for i.MX8 and move imx_lpi2c.h from mx7ulp directory
to u-boot include directory as a common header file.
Signed-off-by: Ye Li <ye.li@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
The SDRAM must first be rewritten by zeroes if ECC is used to initialize
the ECC metadata. Make the CPU overwrite the DRAM with zeroes in such a
case. This scrubbing implementation turns the caches on temporarily, then
overwrites the whole RAM with zeroes, flushes the caches and turns them
off again. This provides satisfactory performance.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
This function was never used in SPL and the default implementation of
dram_bank_mmu_setup() does the same thing. The only difference is the
part which configures OCRAM as cachable, which doesn't really work as
it covers more than the OCRAM.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Chin Liang See <chin.liang.see@intel.com>
Cc: Dinh Nguyen <dinguyen@kernel.org>
Use "%p" to print cmdbuf.
Compilation warning as below:
CC spl/drivers/spi/cadence_qspi_apb.o
LD spl/lib/built-in.o
drivers/spi/cadence_qspi_apb.c: In function ‘cadence_qspi_apb_indirect_write_setup’:
drivers/spi/cadence_qspi_apb.c:696:18: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
cmdlen, (unsigned int)cmdbuf);
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
Use "%zu" for size_t data type.
Compilation warning as below:
In file included from include/linux/bug.h:7:0,
from include/common.h:26,
from drivers/spi/cadence_qspi.c:8:
drivers/spi/cadence_qspi.c: In function ‘cadence_spi_xfer’:
drivers/spi/cadence_qspi.c:211:8: warning: format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
debug("%s: len=%d [bytes]\n", __func__, data_bytes);
^
include/linux/printk.h:37:21: note: in definition of macro ‘pr_fmt’
#define pr_fmt(fmt) fmt
^~~
include/log.h:142:2: note: in expansion of macro ‘debug_cond’
debug_cond(_DEBUG, fmt, ##args)
^~~~~~~~~~
drivers/spi/cadence_qspi.c:211:2: note: in expansion of macro ‘debug’
debug("%s: len=%d [bytes]\n", __func__, data_bytes);
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Acked-by: Marek Vasut <marex@denx.de>
In the device tree, the address for the led is located
in the parent node (for exemple leds), not in the led node
(for exemple led@0).
The commit "led: bcm6328: convert to use live dt"
(sha1: 8994551760)
change this behaviour and read the address in the led node.
We fix this by reading the base address for led
in the parent node.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
In the device tree, the address for cpu is located in
the node "cpus", not in the cpu node (for exemple cpu@0).
So when probing cpu, the cpu address must be read in the
cpu parent.
The commit "cpu: bmips: convert to use live dt"
(sha1: c444afbbef)
change this behaviour and read the address in the
cpu node when probing cpu.
We fix this by reading the address in the cpu parent.
Signed-off-by: Philippe Reynes <philippe.reynes@softathome.com>
The omap_gpio driver has a TODO that says when every board is converted
to DM and DT, the omap_gpio_bind can stop using calloc and switch
to auto-alloc.
This patch converts this driver to auto-calloc when DT is enabled.
Signed-off-by: Adam Ford <aford173@gmail.com>
Add support for loading U-Boot on the Broadcom 7445 SoC. This port
assumes Broadcom's BOLT bootloader is acting as the second stage
bootloader, and U-Boot is acting as the third stage bootloader, loaded
as an ELF program by BOLT.
Signed-off-by: Thomas Fitzsimmons <fitzsim@fitzsim.org>
Cc: Stefan Roese <sr@denx.de>
Cc: Tom Rini <trini@konsulko.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Add code to reset all reset signals as in Ethernet DT node. A reset
property is an optional feature, so only print out a warning and do not
fail if a reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Add code to reset all reset signals as in serial DT node. A reset
property is an optional feature, so do not fail if a reset property is
not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add code to reset all reset signals as in mmc DT node. A reset property
is an optional feature, so only print out a warning and do not fail if a
reset property is not present.
If a reset property is discovered, then use it to deassert, thus
bringing the IP out of reset.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Rename CONFIG_SPL_RESET_SUPPORT to CONFIG_SPL_DM_RESET, so can use
CONFIG_IS_ENABLED(DM_RESET) checking in reset.h later.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds Actions Semi OWL family UART support. This driver
relies on baudrate configured by primary bootloaders.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
This commit adds Actions Semi OWL family base clock and S900 SoC
specific clock support. For S900 peripheral clock support, only UART
clock has been added for now.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add a way to decode a memory region, including the memory type (sram or
sdram) and its start address and size.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new device_bind_ofnode() function which can bind a device given its
ofnode. This allows binding devices more easily with livetree nodes.
Signed-off-by: Simon Glass <sjg@chromium.org>
We have a 32-bit version of this function. Add a 64-bit version as well so
we can easily read 64-bit ints from the device tree.
Signed-off-by: Simon Glass <sjg@chromium.org>
On the A64 the clock for the first USB controller is actually the parent
of the clock for the second controller, so turning them off in that order
makes the system hang.
Fix this by only turning off *both* clocks when the *last* OHCI controller
is brought down. This covers the case when only one controller is used.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
When using CONFIG_OF_BOARD on rpi to use the dtb provided by the
RaspberryPi Fundation, the compatible string isn't the same, resulting
in not-functional usb from u-boot.
Signed-off-by: Oleksandr Tymoshenko <gonzo@FreeBSD.org>
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
Make the initialization sequence consistent with the Linux kernel
driver.
Reviewed-by: Stefan Roese <sr@denx.de>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
This fixes sporadic timeout on initial packet Tx (usually ARP), with an
error message like:
timeout: packet not sent
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Chris Packham <judge.packham@gmail.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Signed-off-by: Rabeeh Khoury <rabeeh@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
phyread can timeout and val will contain random value. Initialize it to
zero not to report random value in case of error.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
When using CONFIG_OF_BOARD on rpi to use the dtb provided by the
RaspberryPi Fundation, the compatible string isn't the same, resulting
in not-functional video in u-boot.
Signed-off-by: Oleksandr Tymoshenko <gonzo@FreeBSD.org>
Signed-off-by: Emmanuel Vadot <manu@freebsd.org>
With the introduction of early timer support in the TSC driver,
the capability of getting clock rate from device tree was lost
unfortunately. Now we bring such functionality back, but with a
limitation that when TSC is used as early timer, specifying clock
rate from device tree does not work.
This fixes random boot failures seen on QEMU targets: printing "TSC
frequency is ZERO" and reset forever.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Masking clock gate, reset register bits based on the
probed controller is proper only due to the assumption
that masking should start with 0 even thought the controller
has separate PHY or shared between OTG.
unfortunately these are fixed due to lack of separate
clock, reset drivers.
Say for example EHCI1 - EHCI3 in the datasheet (EHCI0 is for the OTG)
so we need to start reg_mask 0 - 2.
This patch calculated the mask, based on the register base
so that we can get the proper bits to set with respect to
probed controller.
We even do this masking by using PHY index specifier from dt,
but dev_read_addr_size is failing for 64-bit boards.
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
For ohci, the maximam supported endpoint number is 32(in and out), and
now we have used (usb_pipeendpoint(pipe) << 1) to index the specified
endpoint descritor, usb_pipeendpoint(pipe) can reach 0xf, so we need
change the NUM_EDs from 8 to 32.
Signed-off-by: Zeng Tao <prime.zeng@hisilicon.com>
ohci-hcd casts priv_data pointer to (ohci_t *), thus it must be
the first member in private data struct.
Fixes 831cc98b1 ("usb: sunxi: Simplify ccm reg base code")
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
The N25Q256(A) datasheet clearly states that this device does have
a Flag Status Register and does update FSR PEC bit 7 during Program
and Erase cycles to indicate the cycle is in progress. Enable the
FSR PEC bit polling on this device to prevent data corruption.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Jagan Teki <jagan@openedev.com>
Cc: Tom Rini <trini@konsulko.com>
The claim/release bus function must not reset the whole SPI core because
settings regarding wordlen, clock-frequency and so on made by
set_wordlen, set_mode, set_speed get lost with this action. Resulting in
a non-functional SPI.
Without DM the failure didn't came up since after the spi_reset within
claim bus all the setup (wordlen, mode, ...) was called, in DM they are
called by the spi uclass.
We change now the things as following for having a working SPI instance
in DM:
- move the spi_reset(...) to the probe call in DM for having a known
hardware state after probe. Without DM we don't have a probe call, so we
issue the reset as before during the claim_bus call.
- in release bus we just reset the modulctrl to the reset-value (spi-
slave)
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This bug is the combination of dwc2 USB controller and lan78xx
USB ethernet controller, which is the combination in use on
the Raspberry Pi Model 3 B+.
When the host attempts to receive a packet, but a packet has not
arrived, the lan78xx controller responds by setting BIR
(Bulk-In Empty Response) to NAK. Unfortunately, this hangs
the USB controller and requires the USB controller to
be reset.
The fix proposed is to have the lan78xx controller respond
by setting BIR to ZLP.
Signed-off-by: Andrew Thomas <andrew.thomas@oracle.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
For now, the existing SPL MXS NAND driver only supports to identify
ONFi-compliant NAND chips. In order to allow identifying
non-ONFi-compliant chips add `mxs_flash_full_ident()` which uses the
`nand_get_flash_type()` functionality from `nand_base.c` to lookup
for supported NAND chips in the chip ID list.
For compatibility reason the full identification support is only
available if the config option `CONFIG_SPL_NAND_IDENT` is enabled.
The lookup was tested on a custom i.MX6ULL board with a Toshiba
TC58NVG1S3HTAI0 NAND chip.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The existing `mxs_flash_ident()` is limited to identify ONFi compliant
NAND chips only. In order to support non-ONFi NAND chips refactor the
function and rename it to `mxs_flash_onfi_ident()`.
A follow-up patch will add `mxs_flash_full_ident()` which allows to use
the chip ID list to lookup for supported NAND flashs.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
Add the config option `CONFIG_SPL_NAND_IDENT` for using the NAND chip ID list
to identify the NAND flash in SPL.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
`nand_get_flash_type()` allows identification of supported NAND flashs.
The function is useful in SPL (like mxs_nand_spl.c) to lookup for a NAND
flash (which does not support ONFi) instead of using nand_simple.c and
hard-coding all required NAND parameters.
Signed-off-by: Jörg Krause <joerg.krause@embedded.rocks>
The PFUZE3000 uses registers addresses up to 0xff.
The DM pfuze100 driver supports both pfuze100 and pfuze3000. Allow it
to use the device type to return the correct number of registers.
Also rename the too generic PMIC_NUM_OF_REGS enumeration value for
pfuze3000 to match the other "PFUZE3000_" prefixed enumerations and the
pfuze100 enumeration value PFUZE100_NUM_OF_REGS.
Cc: Peng Fan <Peng.Fan@freescale.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Trent Piepho <tpiepho@impinj.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for specified ECC strength/size using device tree
properties nand-ecc-strength/nand-ecc-step-size.
This aligns behavior with the mainline driver, such that:
- If fsl,use-minimal-ecc is requested it will use data from
data sheet/ONFI. If this is not available the driver will fail.
- If nand-ecc-strength/nand-ecc-step-size are specified those
value will be used.
- By default maximum possible ECC strength is used
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Support driver data from device tree. Also support fsl,use-minimal-ecc
similar to Linux' GPMI NAND driver.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation for device tree support separate board init
from controller init similar to other raw NAND drivers.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
This function initializes DMA descriptors so mxs_nand_init_dma is
more precise. It also frees up the rather generic name mxs_nand_init.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Move GPMI and BCH register structs to the driver struct mxs_nand_info
in prepartion for device tree support.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add support for minimum ECC strength supported by the NAND chip.
This aligns with the behavior when using the fsl,use-minimum-ecc
device tree property in Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Report correct ECC parameters back to the stack. Do not report
bytes as we have it not immeaditly available and the Linux version
also does not report it. It seems to have no aversive effect.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Calculate BCH geometry at start and store the information in
a structure. This avoids recalculation on every page access
and allows to calculate ECC relevant information in one place.
This patch does not change ECC layout or driver behavior in
any way.
The patch aligns the driver somewhat with the Linux GPMI NAND
driver which drives the same IP.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Add config option which allows to enable on flash bad block table
support. This has the same effect as when using the device tree
property "nand-on-flash-bbt" in Linux.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Instead of completing initialization via scan_bbt callback use
NAND self init to initialize the GPMI (MXS) NAND controller.
Suggested-by: Scott Wood <oss@buserror.net>
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
In preparation to convert the driver to use NAND self init
provide a new minimal init for SPL builds. As a side effect
this also reduces size of SPL by about 4KiB.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
commit 8480792287
("spi: omap3: Skip set_mode, set_speed from claim") did break SPI
support on my AM335x board.
The named commit:
- ignored the responsible arguments (speed, mode)
The set speed/mode function must use the supplied function arguments to
work properly. With this commit we take those arguments and transfer
them to the priv-data.
- used wrong udevice pointer for getting priv data
the udevice-pointer within function argument is already the spi-bus
device, so it is wrong looking here for some parent (ocp-bus in this
case) and getting priv-pointer from there.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Otherwise the frequency is zero and the clock divider cannot be setup by
'omap3_spi_set_speed' function.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Jagan Teki <jagan@openedev.com>
CS GPIO activation low/high is determinated by the device tree
so we don't need to take in accoung in cs_activate and cs_deactivate
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
This patch replaced "return 0" with "return status" to fix the
incorrect return value error reported by the coverity.
Reviewed-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Vipul Kumar <vipul.kumar@xilinx.com>
[jagan: rebased on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
In Linux, the clock rate of the UART is given by the clock driver.
If you try to follow that in U-Boot, you would end up with adding
more u-boot,dm-pre-reloc properties, and also the clock driver would
be too big for SPL, which is used for UniPhier ARMv7 platform.
The current solution is to add 'clock-frequency' property to the
UART nodes, but it does not exist in the DT files in Linux. I do
not want to let DT diverge for U-Boot.
Check the SoC compatible and set the clock rate according to it.
This will be helpful to sync DT between Linux and U-Boot.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Use the clk framework to initialize clocks from drivers that need them
instead of having hardcoded frequencies and initializations from board
code.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The SARADC driver was merged after the following commit :
commit d35812368a ("regmap: change regmap_init_mem() to take ofnode instead udevice")
Thus breaking build, this patch fixes the regmap_init_mem accordingly.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
At present the code overruns the bar[] array. Fix this.
At the same time, drop the leading / from the "/spl" path so that we can
run U-Boot SPL with:
spl/u-boot-spl
rather than requiring:
/path/to/spl/u-boot-spl
Reported-by: Coverity (CID: 131199)
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move the strdup() call so that it is only done when we know we will bind
the device.
Reported-by: Coverity (CID: 131216)
Signed-off-by: Simon Glass <sjg@chromium.org>
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The recent DTs have the PHY reset GPIO in the PHY node rather than
the ethernet MAC node, support extracting the PHY reset GPIO info
from both the PHY node and ethernet MAC node.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The RAVB only supports 100Full and 1000Full operation, it does not support
10Full or any Half-duplex modes. The PHY could still advertise those features
though, so filter out the PHY features accordingly.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Do not stop the clock in the start callback in case of failure, keep
them running to also keep the PHY running. The failure could be ie.
PHY failing to negotiate link and if the clock get shut down, another
attempt at bringing the link up would fail. The clock right now are
started in probe function and stopped in remove function, which is
the correct behavior.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Cc: Joe Hershberger <joe.hershberger@ni.com>
The sh_pfc_{read,write}() must operate on the register address directly
rather than on an offset, fix this to prevent illegal access.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Cc: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
There are multiple GPIO banks with up to 32 pins / bank. When
using 'gpio status -a' to read the pins, this patch displays
both GPIO<bank>_<index> similar to how the device trees
display in addition to displaying gpio_#
Signed-off-by: Adam Ford <aford173@gmail.com>
When enabling BLOCK_CACHE on devices with limited RAM during SPL,
some devices may not boot. This creates an option to enable
block caching in SPL by defaults off. It is dependent on SPL_BLK
Fixes: 46960ad6d0 ("block: Have BLOCK_CACHE default to y in some cases")
Signed-off-by: Adam Ford <aford173@gmail.com>
The naming with "UART" is obviously wrong, we fix this here.
Signed-off-by: Hannes Schmelzer <oe5hpm@oevsv.at>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
This adds a DM video driver for U-Boot as the EFI payload. The driver
makes use of all necessary information from the passed EFI GOP info
to create a linear framebuffer device, as if it were initialized by
U-Boot itself.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Anatolij Gustschin <agust@denx.de>
This function is used only inside this driver that's why should be
static.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
This issue was found when OF_LIVE was enabled that there are scrambled
chars on the console like this:
Chip ID: zu3eg
Watchdog: Started��j� sdhci@ff160000: 0, sdhci@ff170000: 1
In: serial@ff010000
I found a solution for this problem exactly the same as I found later in
serial_msm fixed by:
"serial: serial_msm: initialize uart only before relocation"
(sha1: 7e5ad796bc)
What it is happening is that output TX fifo still contains chars to be
sent and _uart_zynq_serial_init() resets TX fifo even in the middle of
transfer.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
