Commit graph

23 commits

Author SHA1 Message Date
Nishanth Menon
4596cf98cd board: ti: dra72: Introduce optimization for rgmii timing for rev C
Rev C version of EVM does require IODelay to be configured for RGMII
pins in MANUAL_1 configuration. Update the same based on PG2.0 initial
simulation values.
Data based on PCT_DRA72x_SR2.0_SR1.0_v1.3.0.7

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:50 -05:00
Lokesh Vutla
4d74804818 board: ti: dra71x-evm: Add mux settings
Add mux and iodelay settings for dra71x-evm.
Data generated using PCT_DRA71x_SR2.0_v1.0.0.0 version (June 2016).

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-12-04 13:54:49 -05:00
Nishanth Menon
8cac14719d board: ti: DRA7: Add DRA72-rev C evm pinmux
Add the pinmux data for rev C evm. This is different from previous
revisions of the platform thanks to the deltas introduced both from
silicon side and from SoC side.

Based on J6EcoES2_EVM_Base_Config-20160309b and PCT-DRA72x-v1.3.0.7 for
SR2.0 silicon.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-27 09:12:16 -04:00
Lokesh Vutla
26eccf31b3 ARM: DRA72-evm: Update mux and VIRTUAL/MANUAL mode timings
All the mux configurations needs to be done as part of the IODelay
sequence to avoid glitch. Adding all the mux configuration, MANUAL/VIRTUAL
mode configuration as needed for DRA72-evm.

Also update the mux for SD card detect on DRA74-evm.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-03-14 19:18:52 -04:00
Vignesh R
900e2104d8 ARM : DRA7: Switch QSPI to use MODE-0 at 64MHz
According to Data Manual(SPRS915P) of AM572x, TI QSPI controller on
DRA74 EVM(rev 1.1+) can support up to 64MHz in MODE-0, whereas MODE-3 is
limited to 48MHz. Hence, switch to MODE-0 for better throughput.
Also, add IODelay parameters for the same.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2016-02-15 12:04:46 -05:00
Cooper Jr., Franklin
bc622966c9 ARM: dra7x/am57x: Remove pin input/output config from WAKEUP pins
The WAKEUP_X pins are always an input no matter the pinmux mode.
However, the 18th bit that typical configures a pin as an input is
considered reserved for the WAKEUP_X pins. Therefore, for any WAKEUP
pin remove any configuration that sets that pin as an input. Since
those pins are only inputs remove any output configuration from those
pins.

Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
2015-11-21 21:50:19 -05:00
Nishanth Menon
0358923409 ARM: DRA74-evm: Add iodelay values for SR2.0
Silicon revision 2.0 has new signal routing hence has an updated set of
iodelay parameters to be used. Update the configuration for the same.
Padmux remains the same.

Based on data from VayuES2_EVM_Base_Config-20150807.

NOTE: With respect to the RGMII values, the Manual IODelay values
are used for the fine adjusments needed to meet the tight RGMII
specification.

Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
2015-08-28 12:33:13 -04:00
Roger Quadros
a5878f1933 ARM: DRA7-evm: prevent DCAN1 _wait_target_disable failure in kernel
If board is booted with transitions happening on DCAN1 pins then
the following warning is seen in the kernel at boot when the
hwmod layer initializes.

"omap_hwmod: dcan1: _wait_target_disable failed"

This is because DCAN1 module's SWAKEUP mechanism is broken
and it fails to correctly turn OFF if it sees a transition on the
DCAN1 pins. Suggested workaround is to keep DCAN1 pins in safe mode
while enabling/disabling DCAN1 module.

The hwmod layer enables and disables all modules at boot
and we have no opportunity to put the DCAN1 pins in safe mode
at that point.

DCAN1 is not used by u-boot so it doesn't matter to it if these
pins are in safe mode. The kernel driver correctly configures
the right mode when DCAN1 is active.

Signed-off-by: Roger Quadros <rogerq@ti.com>
2015-07-08 18:26:42 -04:00
Mugunthan V N
0a888f584c ARM: DRA72x: fix io delay calibration for ethernet
we currently use in-development IODelay values for DRA72x which are
proposed in the data sheet, however, DRA72x EVM uses DP83865 ethernet
Phy over RGMII. The PHY characteristics and routing choices made on
the EVM, make the current iodelay values fail ethernet communication.

Instead, we need to choose custom values for DRA72x-evm specifically
designed for the PHY and routing on the platform for ethernet to
function.

Cc: Nishanth Menon <nm@ti.com>
Cc: Lokesh Vutla <lokeshvutla@ti.com>
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2015-07-07 20:15:52 -04:00
Nishanth Menon
27d170af17 ARM: DRA7-evm: Add mux data
Adding the mux data, manual and virtual mode
settings for DRA7-evm.

Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Vishal Mahaveer <vishalm@ti.com>
2015-06-12 13:02:06 -04:00
Lubomir Popov
ae525189f0 ARM: OMAP5: DRA7xx: Fix misleading comments in mux_data.h
The comments on the QSPI pad assignments erronously swapped
the qspi1_d0 and qspi1_d1 functionality and could cause
confusion. QSPI1_D[0] is in fact muxed on pad U1 (gpmc_a16),
and QSPI1_D[1] - on pad P3 (gpmc_a17). Fixing comments.

Signed-off-by: Lubomir Popov <l-popov@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
2014-12-04 21:28:31 -05:00
Lokesh Vutla
7b92252370 ARM: DRA: Enable VTT regulator
DRA7 evm REV G and later boards uses a vtt regulator for DDR3 termination
and this is controlled by gpio7_11. Configuring gpio7_11.
The pad A22(offset 0x3b4) is used by gpio7_11 on REV G and later boards,
and left unused on previous boards, so it is safe enough to enable gpio
on all DRA7 boards.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
2014-08-25 10:48:13 -04:00
pekon gupta
9352697aa0 board/ti/dra7xx: add support for parallel NOR
This patch adds support for parallel NOR device (S29GL512S10) present on J6-EVM.
The Flash device is connected to GPMC controller on chip-select[0] and accessed
as memory-mapped device. It has data-witdh=x16, capacity-64MBytes(512Mbits) and
is CFI compatible.

As multiple devices are share GPMC pins on this board, so following board
settings are required to detect NOR device:
     SW5.1 (NAND_BOOTn) = OFF (logic-1)
     SW5.2 (NOR_BOOTn)  = ON  (logic-0) /* Active-low */
     SW5.3 (eMMC_BOOTn) = OFF (logic-1)
     SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations:
     SW3.1 (SYSBOOT[ 8])= ON  (logic-1) /* selects SYS_CLK1 speed */
     SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
     SW3.3 (SYSBOOT[10])= ON  (logic-1) /* wait-pin monitoring = enabled */
     SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Non Muxed */
     SW3.5 (SYSBOOT[12])= OFF (logic-0) /* device type: Non Muxed */
     SW3.6 (SYSBOOT[13])= ON  (logic-1) /* device bus-width: 1(x16) */
     SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
     SW3.8 (SYSBOOT[15])= ON  (logic-1) /* reserved */

Also, following changes are required to enable NOR Flash support in
dra7xx_evm board profile:
2014-08-25 10:48:12 -04:00
pekon gupta
54a97d2849 board/ti/dra7xx: add support for parallel NAND
This patch adds support for x16 NAND device (MT29F2G16AAD) connected to GPMC
chip-select[0] on DRA7xx EVM.
As GPMC pins are shared by multiple devices, so in addition to this patch
following board settings are required for NAND device detection [1]:

  SW5.9 (GPMC_WPN)   = OFF (logic-1)
  SW5.1 (NAND_BOOTn) = ON  (logic-0) /* Active-low */
  SW5.2 (NOR_BOOTn)  = OFF (logic-1)
  SW5.3 (eMMC_BOOTn) = OFF (logic-1)
  SW5.4 (QSPI_BOOTn) = OFF (logic-1)

And also set appropriate SYSBOOT configurations
  SW2.1 (SYSBOOT[0]) = ON  (logic-1) /* selects NAND Boot */
  SW2.2 (SYSBOOT[1]) = OFF (logic-0) /* selects NAND Boot */
  SW2.3 (SYSBOOT[2]) = OFF (logic-0) /* selects NAND Boot */
  SW2.4 (SYSBOOT[3]) = OFF (logic-0) /* selects NAND Boot */
  SW2.5 (SYSBOOT[4]) = ON  (logic-1) /* selects NAND Boot */
  SW2.6 (SYSBOOT[5]) = ON  (logic-1) /* selects NAND Boot */
  SW2.7 (SYSBOOT[6]) = OFF (logic-0) /* reserved */
  SW2.8 (SYSBOOT[7]) = OFF (logic-0) /* reserved */

  SW3.1 (SYSBOOT[ 8])= ON  (logic-1) /* selects SYS_CLK1 speed */
  SW3.2 (SYSBOOT[ 9])= OFF (logic-0) /* selects SYS_CLK1 speed */
  SW3.3 (SYSBOOT[10])= ON  (logic-1) /* wait-pin monitoring = enabled */
  SW3.4 (SYSBOOT[11])= OFF (logic-0) /* device type: Addr/Data Muxed */
  SW3.5 (SYSBOOT[12])= ON  (logic-1) /* device type: Addr/Data Muxed */
  SW3.6 (SYSBOOT[13])= ON  (logic-1) /* device bus-width: 1(x16) */
  SW3.7 (SYSBOOT[14])= OFF (logic-0) /* reserved */
  SW3.8 (SYSBOOT[15])= ON  (logic-1) /* reserved */

Following changes are required in board.cfg to enable NAND on J6-EVM:
2014-08-25 10:48:12 -04:00
Albert ARIBAUD
b1cdd8baa1 Merge branch 'u-boot-ti/master' into 'u-boot-arm/master' 2014-07-28 12:26:21 +02:00
Mugunthan V N
e5ff845bff ARM: DRA7xx: Add cpsw second port pinmux
Add cpsw second slave port pinmux to use it as primary ethernet port

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2014-07-25 15:21:05 -04:00
Felipe Balbi
49b633b3d3 board: ti: dra7xx: add mux data for UART3
J6 EVM can be built with UART3 as console, but currently
there's nothing muxing UART3 correctly. Likely this only
works because, based on commit log, author was only testing
with UART3 boot and - I assume - ROM code leave UART3 correctly
muxed in that case.

If we want to boot from MMC and still use UART3 as console,
then we need to mux those signals correctly.

Signed-off-by: Felipe Balbi <balbi@ti.com>
2014-07-07 19:42:34 -04:00
Dan Murphy
834e91af43 usb: dra7xx: Add support for dra7xx xhci USB host
Add the support for the dra7xx xhci usb host.
dra7xx does not contain an EHCI controller so the headers
can be removed from the board file.

The xHCI host on dra7xx is connected to a usb2 phy so need to
add support to enable those clocks.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
2013-10-20 23:42:41 +02:00
Matt Porter
247cdf0413 dra7xx_evm: add SPL API, QSPI, and serial flash support
Enables support for SPI SPL, QSPI and Spansion serial flash device
on the EVM. Configures pin muxes for QSPI mode.

Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com>
2013-10-07 17:55:52 +05:30
Mugunthan V N
dec7f74835 ARM: DRA7xx: Add CPSW and MDIO pinmux support
Adding CPSW Slave 0 and MDIO pinmux support for DRA7xx EVM

Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
2013-07-26 16:39:11 -04:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Lokesh Vutla
7f36c88f64 ARM: DRA7xx: Update pinmux data
Updating pinmux data as specified in the latest DM

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
2013-06-10 08:43:10 -04:00
Lokesh Vutla
687054a7e0 arm: dra7xx: Add board files for DRA7XX socs
Adding new board files for DRA7XX socs.
The pad registers layout is changed completely from OMAP5
So introducing the new structure here and also adding the
minimal data.

Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishant Kamat <nskamat@ti.com>
Signed-off-by: R Sricharan <r.sricharan@ti.com>
Reviewed-by: Tom Rini <trini@ti.com>
[trini: Adapt omap_mmc_init call for last 2 params]
Signed-off-by: Tom Rini <trini@ti.com>
2013-03-11 11:39:30 -04:00