With DM enabled the ethernet code will receive a packet, call
the push method that's set by the EFI network implementation
and then free the packet. Unfortunately the push methods only
sets a flag that the packet needs to be handled, but the code
that provides the packet to an EFI application runs after the
packet has already been freed.
To rectify this issue, adjust the push method to accept the packet
and store it in a temporary buffer. The EFI application then gets
the data copied from that buffer. This way the packet is cached
until is is needed.
The DM Ethernet stack tries to receive 32 packets at once, thus
we better allocate as many buffers as the stack.
Signed-off-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.
Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.
Signed-off-by: Simon Glass <sjg@chromium.org>
Implement the MCastIPtoMAC service of the simple network protocol.
It converts an multicast IPv4 (or IPv6) address to a multicast Ethernet
address.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
The network should start in status EfiSimpleNetworkStopped.
Add and correct status checks in the simple network protocol.
Correct the unit test:
* Shutdown() and Stop() during setup if needed
* invoke Shutdown() before Stop() when tearing down
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Fill the media header in EFI_SIMPLE_NETWORK.Transmit().
Check that the buffer size is large enough for the header.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
GetStatus() must clear the interrupt status.
Transmit() should set the TX interrupt.
Receive() should clear the RX interrupt.
Initialize() and Start() should clear the interrupt status.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
U-Boot implements the EFI_PXE_BASE_CODE_PROTOCOL because GRUB uses the mode
information for booting via PXE. All function pointers in the protocol were
NULL up to now which will cause immediate crashes when the services of the
protocol are called.
Create function stubs for all services of the protocol returning
EFI_UNSUPPORTED.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Check buffer pointers are not NULL as required by the UEFI 2.7 spec.
Return EFI_UNSUPPORTED instead of EFI_INVALID_PARAMETER when trying to
transmit with non-zero header_size.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We should consistently use the same name for protocol GUIDs as defined in
the UEFI specification. Not adhering to this rule has led to duplicate
definitions for the EFI_LOADED_IMAGE_PROTOCOL_GUID.
Adjust misnamed protocol GUIDs.
Adjust the text for the graphics output protocol in the output of the
`efidebug dh` command.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
We should not call eth_rx() before the network interface is initialized.
The services of the simple network protocol should check the state of
the network adapter.
Add and correct comments.
Without this patch i.mx6 system Wandboard Quad rev B1 fails to execute
bootefi selftest.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Calling net_send_packet() requires that the buffer is aligned to a multiple
of PKTALIGN (= ARCH_DMA_MINALIGN). The UEFI spec does not require
efi_net_transmit() to be called with a buffer with any special alignment.
So we have to copy to an aligned buffer. The current coding copies to an
aligned buffer only if CONFIG_EFI_LOADER_BOUNCE_BUFFER=y. Many boards
like the Odroid C2 do not use a bounce buffer.
With the patch we copy to a correctly aligned buffer in all cases.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Rename the component parent of some EFI objects to header. This avoids
misunderstandings.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
A pointer to a struct efi_object is a handle. We do not need any handle
member in this structure. Let's eliminate it.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In int-ll64.h, we always use the following typedefs:
typedef unsigned int u32;
typedef unsigned long uintptr_t;
typedef unsigned long long u64;
This does not need to match to the compiler's <inttypes.h>.
Do not include it.
The use of PRI* makes the code super-ugly. You can simply use
"l" for printing uintptr_t, "ll" for u64, and no modifier for u32.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
if_type is not correctly initialized
Failure to initialize if_type means that grub2/efinet sends
a bogus arp request. It therefore gets no response. On Raspberry Pi 3B+
this leads to a pause at:
lan78xx_eth Waiting for PHY auto negotiation to complete....... done
lan78xx_eth Waiting for PHY auto negotiation to complete....... done
Signed-off-by: Andrew Thomas <andrew.thomas@oracle.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.
Fixes: 83d290c56f ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.
Signed-off-by: Tom Rini <trini@konsulko.com>
Add missing network initialization code.
Before the patch the network was only usable if a network command like
dhcp or tftp had beed executed.
This was visible when interrupting the console countdown and executing
bootefi selftest for vexpress_ca15_tc2_defconfig.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
We use a timer to poll the network.
iPXE is used for booting from iSCSI drives. It has been changed to run at
TPL_CALLBACK most of the time (which is not what the UEFI spec
recommends).
By changing our timer to TPL_NOTIFY we can ensure that it is nevertheless
executed.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
If an event of a group event is signaled all other events of the same
group are signaled too.
Function efi_signal_event is renamed to efi_queue_event.
A new function efi_signal_event is introduced that checks if an event
belongs to a group and than signals all events of the group.
Event group notifciation is implemented for ExitBootServices,
InstallConfigurationTable, and ResetSystem.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Consistently return status codes form efi_net_register().
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
To avoid duplicate coding provide a helper function that
initializes an EFI object and adds it to the EFI object
list.
efi_exit() is the only place where we dereference a handle
to obtain a protocol interface. Add a comment to the function.
Suggested-by: Alexander Graf <agraf@suse.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Use efi_add_protocol to add protocols.
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
Calloc may return NULL. So we must check the return value.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
In the receive function all return values should be filled.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The size fields in the Simple Network Protocol are all
UINTN in the UEFI spec. So use size_t.
Provide a function description of the receive function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The returned interrupt status was wrong.
As out transmit buffer is empty we need to always set
EFI_SIMPLE_NETWORK_TRANSMIT_INTERRUPT.
When we have received a packet we need to set
EFI_SIMPLE_NETWORK_RECEIVE_INTERRUPT.
Furthermore we should call efi_timer_check() to handle events.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The WaitForPacket event informs that a network package has been
received by the SimpleNetworkProtocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: Move is_signaled = true line into efi_net_push()]
Signed-off-by: Alexander Graf <agraf@suse.de>
A timer event is defined. The timer handler cares for receiving new
packets.
efi_timer_check is called both in efi_net_transmit and efi_net_receive
to enable events during network communication.
Calling efi_timer_check in efi_net_get_status is implemented in a
separate patch.
[agraf] This patch is needed to make efi_net_get_status() actually
report incoming packets.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix spelling in comment]
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
U-Boot does not implement all functions of the simple network
protocol. The unimplemented functions return either of
EFI_SUCCESS and EFI_INVALID_PARAMETER.
The UEFI spec foresees to return EFI_UNSUPPORTED in these cases.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
The length of a MAC address is 6.
We have to set this length in the EFI_SIMPLE_NETWORK_MODE
structure of the EFI_SIMPLE_NETWORK_PROTOCOL.
Without this patch iPXE fails to initialize the network with
error message
SNP MAC(001e0633bcbf,0x0) has invalid hardware address length 0
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Provide the simple network protocol revision.
This revision number could be used to identify backwards compatible
enhancements of the protocol.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Alexander Graf <agraf@suse.de>
Get rid of the hacky fake boot-device and duplicate device-path
constructing (which needs to match what efi_disk and efi_net do).
Instead convert over to use efi_device_path helpers to construct
device-paths, and use that to look up the actual boot device.
Also, extract out a helper to plug things in properly to the
loaded_image. In a following patch we'll want to re-use this in
efi_load_image() to handle the case of loading an image from a
file_path.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
efi_open_protocol was implemented to call a protocol specific open
function to retrieve the protocol interface.
The UEFI specification does not know of such a function.
It is not possible to implement InstallProtocolInterface with the
current design.
With the patch the protocol interface itself is stored in the list
of installed protocols of an efi_object instead of an open function.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: fix efi gop support]
Signed-off-by: Alexander Graf <agraf@suse.de>
When adding network interface node use Messaging device path with
subtype MAC Address and device's MAC address as a value instead
of Media Device path type with subtype File Path and path "Net"
Signed-off-by: Oleksandr Tymoshenko <gonzo@bluezbox.com>
Signed-off-by: Alexander Graf <agraf@suse.de>
These are missing in some functions. Add them to keep things consistent.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
Signed-off-by: Alexander Graf <agraf@suse.de>
So far bounce buffers were only used for disk I/O, but network I/O
may suffer from the same problem.
On platforms that have problems doing DMA on high addresses, let's
also bounce outgoing network packets. Incoming ones always already
get bounced.
This patch fixes EFI PXE boot on ZynqMP for me.
Signed-off-by: Alexander Graf <agraf@suse.de>
We can now successfully boot EFI applications from disk, but users
may want to also run them from a PXE setup.
This patch implements rudimentary network support, allowing a payload
to send and receive network packets.
With this patch, I was able to successfully run grub2 with network
access inside of QEMU's -M xlnx-ep108.
Signed-off-by: Alexander Graf <agraf@suse.de>
