Enable CONFIG_DM_USB to remove below compile warning:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
With DM_USB enabled, enable CONFIG_BLK to remove this
compile warning for ls1012afrdm based targets:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1046A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
This supports i2c DM and enables CONFIG_DM_I2C
for SoC LS1043A
Signed-off-by: Biwen Li <biwen.li@nxp.com>
Signed-off-by: Priyanka Jain <priyanka.jain@nxp.com>
Currently this causes failures of the platform when running the EFI
loader tests, so disable it for now.
This reverts commit af827140e5.
Signed-off-by: Tom Rini <trini@konsulko.com>
Currently the following error message is seen during boot:
U-Boot 2020.01-08751-g55759ae141 (Mar 09 2020 - 14:44:52 -0300)
Model: Elgin RV1108 R1 board
DRAM: 128 MiB
APLL: 600000000 DPLL:1200000000 GPLL:1188000000
ACLK_BUS: 148500000 ACLK_PERI:148500000 HCLK_PERI:148500000 PCLK_PERI:74250000
MMC: dwmmc@30110000: 0
Loading Environment from MMC... OK
In: serial@10210000
Out: serial@10210000
Err: serial@10210000
Model: Elgin RV1108 R1 board
rockchip_dnl_key_pressed: adc_channel_single_shot fail!
....
Since the elgin-rv1108 does not use ADC to read the download
key status, select CONFIG_ROCKCHIP_BOOT_MODE_REG=0 to avoid
such error.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Since commit 8e9a8d0d0c ("rockchip: elgin-rv1108: use board_early_init_f
for per-boar init") the function that configure the board GPIOs is no
longer called since CONFIG_BOARD_EARLY_INIT_F=y is not selected.
These GPIOs do not need to be configured in such early stagem, so change it
to rk_board_late_init() and also select CONFIG_BOARD_LATE_INIT=y
to fix the regression.
Signed-off-by: Otavio Salvador <otavio@ossystems.com.br>
Signed-off-by: Fabio Berton <fabio.berton@ossystems.com.br>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
These boards aren't ChromeOS devices so won't have a cros-ec-keyb
input as it's the keyboard available via the ChromeOS Embedded
Controller. Update them to use a USB keyboard which would actually
be available. Also enable the usb keyboard option for those devices
that don't have it enabled already.
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Reviewed-by: Michael Trimarchi <michael@amarulasolutions.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
EFI was disabled in f95b8a4b5f because of the missing DTB file,
and indeed, the DTB file is required to load recent versions of GRUB
(2.04) correctly.
Signed-off-by: Kristian Amlie <kristian.amlie@northern.tech>
This pull request provides the hardware RNG driver for Amlogic systems needed
for the EFI_RNG_PROTOCOL.
Furthermore bug fixes are provided:
* correct an error message in the efidebug command
* correct an error in the 'efidebug rm' command
* remove an unnecessary assignment in efi_queue_event()
-----BEGIN PGP SIGNATURE-----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=fiKc
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-04-rc4-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-04-rc4 (3)
This pull request provides the hardware RNG driver for Amlogic systems needed
for the EFI_RNG_PROTOCOL.
Furthermore bug fixes are provided:
* correct an error message in the efidebug command
* correct an error in the 'efidebug rm' command
* remove an unnecessary assignment in efi_queue_event()
For all sandbox systems with DM_RNG we enable RNG_SANDBOX. So we can simply
set the default to yes.
All rng drivers depend on DM_RNG. Use a single 'if' instead of individual
dependencies. Now 'make menuconfig' shows the individual drivers neatly
indented under the DM_RNG entry.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Sughosh Ganu <sughosh.ganu@linaro.org>
-----BEGIN PGP SIGNATURE-----
iQFQBAABCgA6FiEEqxhEmNJ6d7ZdeFLIHrMeAg6sL8gFAl5nWr8cHGV1Z2VuLmhy
aXN0ZXZAbWljcm9jaGlwLmNvbQAKCRAesx4CDqwvyGaOCACkavhqX4EP1FeRDX7m
Uujnacekt0y0uC54aGqBZ2u8Y+iwFza7rd4RcWOAx1pHq1QggAF+h5So8cOfSjpD
6Uad4ql0EOYuH5xcFYCzmEmOMj25DrIZ0F+nPnxhdK0novBrUO8QD2v4r8TgrcWs
dFxe7RCvop4I54Bq14LzZsCozlYEqHaf5E3fSas2LVeDIBrkzGh6pYhWM62FFRuy
71kIC+y9pfRPXaeiOSDp1ZqPkzQA8xw5AWAx4TCmTZ1DjLLBAoRbe0Iv9fseHct0
BFGD4+G1g0GfrNrjAG2OPAePDXq+6fmoAZFbkDGeoFwGnZXhxEnVnN4w5t+Hl0H4
82tF
=eO+8
-----END PGP SIGNATURE-----
Merge tag 'u-boot-atmel-fixes-2020.04-a' of https://gitlab.denx.de/u-boot/custodians/u-boot-atmel
First set of u-boot-atmel fixes for 2020.04 cycle:
- Includes two small configuration fixes that will solve the SPL booting
on sama5d3_xplained board.
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
This fixes the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Pedro Jardim <jardim.c.pedro@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Booting a mainline kernel in secure mode on i.MX7D causes only
one CPU to be brought up.
Change it to booting in non secure mode by default, which
allows the two CPUs to be brought up.
It does have a side effect of not probing the CAAM driver.
If CAAM driver is needed then a secure world OS such as OPTEE needs
to be used.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Convert imx6sabresd ethernet to driver model to fix the following warning:
===================== WARNING ======================
This board does not use CONFIG_DM_ETH (Driver Model
for Ethernet drivers). Please update the board to use
CONFIG_DM_ETH before the v2020.07 release. Failure to
update by the deadline may result in board removal.
See doc/driver-model/migration.rst for more info.
====================================================
Signed-off-by: Alifer Moraes <alifer.wsdm@gmail.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
On the aristainetos2c boards the PMIC needs to be initialized,
because the Ethernet PHY uses a different regulator that is not
setup per hardware default. This does not influence the other
versions as this regulator isn't used there at all.
Signed-off-by: Heiko Schocher <hs@denx.de>
With CONFIG_SUPPORT_EMMC_BOOT moved to Kconfig, move it to defconfig
files.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Add initial support for the ABB SECU board, which is an ArriaV-based
SoCFPGA system with ethernet and booting from Denali NAND.
Signed-off-by: Holger Brunck <holger.brunck@ch.abb.com>
Cc: Ley Foon Tan <ley.foon.tan@intel.com>
Cc: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
-----BEGIN PGP SIGNATURE-----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=h4lQ
-----END PGP SIGNATURE-----
Merge tag 'uniphier-v2020.04-3' of https://gitlab.denx.de/u-boot/custodians/u-boot-uniphier
UniPhier SoC updates for v2020.04 (3rd)
- Enable ADMA and HS400 for the eMMC driver on 64-bit SoCs
- Add some convenient environment variables to handle SD card
- Sanitize the NAND controller reset sequence and its WP handling
- Sync DT with Linux
The board uses 100 MHz clock for UART bitrate generator,
but is configured as 50 MHz on defconfig.
This produces wrong console output.
The first message, "Debug uart enabled" is received as:
"������b"
Fix the issue by configuring the correct clock for the
UART baudrate generator
Signed-off-by: Milan Obuch <u-boot@dino.sk>
Signed-off-by: Luis Araneda <luaraneda@gmail.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
The eMMC controller on LD20 or later supports HS-400 mode. It works on
a quick test. Enable it in case somebody may want to use it.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
This fixes the inadvertent definition of CONFIG_DTB_RESELECT and
CONFIG_MULTI_DTB_FIT in the K2x HS defconfigs, that happened as part of
a resync of the defconfigs.
The inclusion of these config options causes ethernet to stop working on
K2x HS devices as they interfere with the installation of the secure
boot monitor.
This patch also removes the above configs for the K2 GP devices, as they
are not needed, and to keep the differences between the GP and HS
defconfigs to a minimum.
Signed-off-by: Madan Srinivas <madans@ti.com>
Signed-off-by: Andrew F. Davis <afd@ti.com>
When the board was originally submitted, it was attempting to use the
ESDHC driver. The board uses the USDHC driver.
Signed-off-by: Carl Gelfand <carl@novtech.com>
Cc: Shawn Guo <shawn.guo@kernel.org> (maintainer:MEERKAT96 BOARD)
Acked-by: Shawn Guo <shawnguo@kernel.org>
This reverts commit 02dc1599ba
Commit 02dc1599ba ("configs: enable sata, eSDHC, USB device module in
T2080QDS")
has some sata defconfig changes to fit support DM mode, Now the driver
will be reverted, So revert it.
Signed-off-by: Peng Ma <peng.ma@nxp.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
There are many boards share the board file and device header file with
rk3399 evb, add target type MACRO so that it is fixed instead of default
to the first target in "RK3399 board select".
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Added support for onboard LED's and push button. When powered board will be
in low power mode(yellow LED), on button press, board enters full power mode
(red LED) and boots u-boot.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
roc-pc-rk3399 board has one user button & three user LED's. Currently
we don't have any code support for these devices. Since button and LED's are
specific to roc-pc-rk3399 board, split it into its own board file and add code
support here.
Signed-off-by: Suniel Mahesh <sunil@amarulasolutions.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE56Yx6b9SnloYCWtD4rK92eCqk3UFAl5GcB0ACgkQ4rK92eCq
k3Wr9gf/dDPJi6UBhLDio/IVKDBddOEUN0Lwdr9W0upL+DrdvEOyNyMSEKuLccIE
UTd1NmNNwcvgDRaPvB5o3R7twWItTW0cYlmVkFSZ228aq6xdf/SElN2OUD6B9Gh+
8bi6oVLu41TNMYn4VYxsEftcT2megfH8s+SH/FlvR5ua1yCC1vyrytEQjPIbJAB2
sa90ewDyp5EYqGLdAk6AVjPLeNZsaleGwuyLf04PoC2xhn+3HTEKJCJN4O46aJUr
0GUI7YN7pTjIfZdYfFqjcwoQV1xV2HtbjCTcOb8Td8TEYjIoILF8tSyfIwDXWGB5
zMQIQxUdQyNiqdBPFcnkAufjk+zLIQ==
=0dG+
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20200214' of https://gitlab.denx.de/u-boot/custodians/u-boot-stm
- add DH Electronics DHCOM SoM and PDK2 board
- DT alignment with kernel v5.5-rc7 for stm32mp1 boards
- fix STM32 image format for big endian hosts in mkimage
- solve warnings in device tree and code for stm32mp1 boards
- remove fdt_high and initrd_high for stm32 and stih boards
- add support of STM32MP15x Rev.Z
- update stm32mp1 readme
Add mmc device partition 0 as the seat of the environment.
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
