The data read is not working when using FIFO mode.
From DesignWare databook, when a Data_Transfer_Over (DTO) interrupt is
received, the software should read the remaining data from FIFO.
Add DTO interrupt checking on data read path and clear interrupts before
start reading from FIFO. So, it doesn't clear the next pending
interrupts unintentionally after read from FIFO.
Signed-off-by: Ley Foon Tan <ley.foon.tan@intel.com>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With a 48MHz input clock, the lowest bus frequency can be as low as
48000000 / (4 * 4095) = 2930Hz. Such an extremely low frequency will cause
the mmc framework take seconds to finish the initialization.
Limiting the minimum bus frequency to a slightly higher value can solve the
issue without any side effects.
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Weijie Gao <weijie.gao@mediatek.com>
imx8mm ekv has been switched to use distro boot commands, but had no
correct options enabled to support sysboot.
According to the README.distro, sysboot is consindered to be a
recommended way of using distro boot commands, it required default distro
features to be enabled instead of only those that are relevant to the boot
script.
Replace the boot script specific options in the config to a default distro
option.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Fixes: 2df8930bf9 ("imx8mm: configs: add support for distro boot commands")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
imx8mp ekv has been switched to use distro boot commands, but had no
correct options enabled to support sysboot.
According to the README.distro, sysboot is consindered to be a
recommended way of using distro boot commands, it required default distro
features to be enabled instead of only those that are relevant to the boot
script.
Replace the boot script specific options in the config to a default distro
option.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Fixes: 9b162b1d1f ("imx8mp: configs: add support for distro boot commands")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Remove the LED unit addresses and reg properties to
fix the following dtc build warnings:
arch/arm/dts/o4-imx-nano.dtb: Warning (reg_format): /leds/led@0:reg: property has invalid length (4 bytes) (#address-cells == 2, #size-cells == 1)
...
arch/arm/dts/o4-imx-nano.dtb: Warning (avoid_default_addr_size): /leds/led@0: Relying on default #address-cells value
Reported-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Oleh Kravchenko <oleg@kaa.org.ua>
- stm32_qspi: Fix short data write operation
- dfu: set max_buf_size to erasesize also for NOR devices
- Fixes ethernet clock property name for STM32MP1 board
- STM32CubeProgrammer: various fixes
- clk: cosmetic update for clk-uclass
-----BEGIN PGP SIGNATURE-----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=5v48
-----END PGP SIGNATURE-----
Merge tag 'u-boot-stm32-20210618' of https://source.denx.de/u-boot/custodians/u-boot-stm into next
- stm32mp157c-odyssey-som DT fixes
- stm32_qspi: Fix short data write operation
- dfu: set max_buf_size to erasesize also for NOR devices
- Fixes ethernet clock property name for STM32MP1 board
- STM32CubeProgrammer: various fixes
- clk: cosmetic update for clk-uclass
clean up octeontx_smi_probe by using the live-tree API.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
If the environment does not have "soc" or "board" set, and fdtdir
option is specified in extlinux.conf, the bootloader will crash whilst
dereferencing a null pointer. Add a guard against null soc or
board. Fixes a crash of qemu-riscv64_smode configuration, which does
not have CONFIG_SYS_SOC defined.
Signed-off-by: Dimitri John Ledkov <xnox@ubuntu.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Linux uses the prefix "ethernet" whereas u-boot uses "eth". This is from
the linux tree:
$ grep "eth[0-9].*=.*&" arch/**/*dts{,i}|wc -l
0
$ grep "ethernet[0-9].*=.*&" arch/**/*dts{,i}|wc -l
633
In u-boot device trees both prefixes are used. Until recently the only
user of the ethernet alias was the sandbox test device tree. This
changed with commit fc054d563b ("net: Introduce DSA class for Ethernet
switches"). There, the MAC addresses are inherited based on the devices
sequence IDs which is in turn given by the device tree.
Before there are more users in u-boot and both worlds will differ even
more, rename the alias prefix to "ethernet" to match the linux ones.
Also adapt the test cases and rename any old aliases in the u-boot
device trees.
Cc: David Wu <david.wu@rock-chips.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
If the environment variable "ethact" is not set, the first device in the
uclass is returned. This depends on the probing order of the ethernet
devices. Moreover it is not not configurable at all.
Try to return the ethernet device with sequence id 0 first which then
can be configured by the aliases in a device tree. Fall back to the old
mechanism in case of an error.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Commit 4f0278dac5 ("net: sun8i-emac: Lower MDIO frequency") leads to
network failure on the OrangePi PC.
=> dhcp
sun8i_emac_eth_start: Timeout
According to the commit message the change of the MDIO frequency is only
required for external PHYs.
Fixes: 4f0278dac5 ("net: sun8i-emac: Lower MDIO frequency")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add SynQuacer's NETSEC GbE controller driver.
Since this driver will load the firmware from SPI NOR flash,
this depends on CONFIG_SYNQUACER_SPI=y.
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Revert some changes of commit 3a97da12ee ("net: dwc_eth_qos: add dwc
eqos for imx support") that were probably added by mistake.
One of these changes can lead to received data corruption (enabling
FUP and FEP bits). Another causes invalid register rxq_ctrl0 settings
for some platforms. And another makes some writes at unknown memory
location.
Fixes: 3a97da12ee ("net: dwc_eth_qos: add dwc eqos for imx support")
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ye Li <ye.li@nxp.com>
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Disabling clk_ck clock leads to link up status loss in phy, which
leads to auto-negotiation restart before each network command
execution.
This issue is especially big for PXE boot protocol because of
auto-negotiation restarts before each configuration filename trial.
To avoid this issue don't disable clk_ck clock after it was enabled.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Ramon Fried <rfried.dev@gmail.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
commit f1bcad22dd ("net: e1000: add support for writing to EEPROM")
adds support for storing hwaddr in EEPROM however i210 devices do not
support this and thus results in errors such as:
Warning: e1000#0 failed to set MAC address'
Check if a flash device is present and if not return -ENOSYS indicating
this is not supported.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Reviewed-by: Ramon Fried <rfried.dev@gmail.com>
Remove the tab in clk_get_bulk to respect the coding rules.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add error callback in dfu stack to manage some board specific
behavior on DFU targets.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Move the message "Invalid or missing layout file."
to debug level as it is a normal behavior and not an error
and add the missing '\n'.
This patch avoids the strange trace :
Boot over usb0!
Invalid or missing layout file.DFU alt info setting: done
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use get_cpu_dev() in uart getID command and remove the defines
DEVICE_ID_BYTE1 and 2 defines.
This patch prepare the support for new SOC family.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Correctly handle number of alternate when DM_PMIC is not activated.
This patch remove the last UNKNOWN partition in this case.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Handle the second USB enumeration only when the flashlayout is received
and when phase is PHASE_FLASHLAYOUT. This patch removes the call of
stm32prog_next_phase as it is already done in stm32prog_dfu_init().
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
When CONFIG_FIT_SIGNATURE is activated, CONFIG_LEGACY_IMAGE_FORMAT
is deactivated and the define IMAGE_FORMAT_LEGACY don't exist with
include/image.h:
#if defined(CONFIG_LEGACY_IMAGE_FORMAT)
#define IMAGE_FORMAT_LEGACY 0x01 /* legacy image_header based format */
#endif
This patch adds the needed check on compilation flag
CONFIG_LEGACY_IMAGE_FORMAT to avoid the compilation error
for command stm32prog:
cmd_stm32prog.c:81:8: error: ‘IMAGE_FORMAT_LEGACY’ undeclared
(first use in this function); did you mean ‘IMAGE_FORMAT_FIT’?
81 | if (IMAGE_FORMAT_LEGACY ==
| ^~~~~~~~~~~~~~~~~~~
| IMAGE_FORMAT_FIT
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Add the support in command stm32prog of kernel load and start
with initrd file, identify by the partition Type "Binary" in
the flashlayout.tsv, for example:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 kernel System ram0 0xC2000000 uImage.bin
P 0x11 dtb FileSystem ram0 0xC4000000 board.dtb
P 0x12 initrd Binary ram0 0xC4400000 <initrd>
The <initrd> file can be a legacy image "uInitrd", generated
with mkimage, or a RAW initrd image "initrd.gz".
After a DFU detach the bootm command with be executed
with the associated address, for example:
$> bootm 0xC2000000 0xC4400000:<size> 0xC4000000
When the "Binary" partition type is absent, the 'bootm'
command starts the kernel without ramdisk, for example:
$> bootm 0xC2000000 - 0xC4000000
With this paths, it is no more mandatory to generate FIT
including the kernel, DT and initrd:
- 0x01 fsbl Binary none 0x0 tfa.stm32
- 0x03 fip Binary none 0x0 fip.bin
P 0x10 fit System ram0 0xC2000000 fit.bin
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Handle timeout in stm32prog_serial_get_buffer to sent NACK
to STM32CubeProgrammer when the buffer is not fully received.
This patch avoids to reach the STM32CubeProgrammer timeout and
the associated unrecoverable error.
Timeout error occurred while waiting for acknowledgment.
Error: Write Operation fails at packet number 4165 at address 0x1044FF
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
This patch removes the header check for UART download;
the check of checksum is not mandatory with even parity and chuck
checksum for each 256 received bytes and it is only done for
STM32 image (FSBL = TF-A BL2), not for FIT image.
This patch solve issue of duplicated 0x100 byte written with FIP header.
Fixes: 4fb7b3e108 ("stm32mp: stm32prog: add FIP header support")
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Use the correct name for STMicroelectronics phys config properties,
replace '_' by '-':
"st,eth_clk_sel" => "st,eth-clk-sel"
"st,eth-ref-clk-sel" => st,eth-clk-sel"
These property name are aligned with the upstreamed Linux kernel binding:
linux/Documentation/devicetree/bindings/net/stm32-dwmac.yaml
See Linux kernel commit "dt-bindings: net: stmmac: add phys config
properties" merged in v5.1-rc1.
This patch allow to reuse the kernel device tree directly in U-Boot.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
For NOR devices the logical DFU buffer size is the sector_size,
as it is done in dfu_sf.c or in spi/sf_mtd.c
(sf_mtd_info.erasesize = flash->sector_size)
For NAND the DFU size was already limited to erasesize as
has_pages = true.
So the mtd dfu backend can use this erasesize for all the MTD devices,
NOR and NAND with dfu->max_buf_size = mtd->erasesize
This difference was initially copied from MTD command, where
data is fully available in RAM without size limitation.
This patch avoids to have many sector write in dfu_mtd.c at the end
of the DFU transfer and avoids issues with USB timeout or WATCHDOG.
Signed-off-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
TCF flag only means that all data was sent to FIFO. To check if the
data was sent out of FIFO we should also wait for the BUSY flag to be
cleared. Otherwise there is a race condition which can lead to
inability to write short (one byte long) data.
Signed-off-by: Daniil Stas <daniil.stas@posteo.net>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@foss.st.com>
This driver supports Rockchip NFC (NAND Flash Controller) found on
RK3308, RK2928, RKPX30, RV1108 and other SOCs. The driver has been
tested using 8-bit NAND interface on the ARM based RK3308 platform.
Support Rockchip SoCs and NFC versions:
- PX30 and RK3326(NFCv900).
ECC: 16/40/60/70 bits/1KB.
CLOCK: ahb and nfc.
- RK3308 and RV1108(NFCv800).
ECC: 16 bits/1KB.
CLOCK: ahb and nfc.
- RK3036 and RK3128(NFCv622).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb and nfc.
- RK3066, RK3188 and RK2928(NFCv600).
ECC: 16/24/40/60 bits/1KB.
CLOCK: ahb.
Supported features:
- Read full page data by DMA.
- Support HW ECC(one step is 1KB).
- Support 2 - 32K page size.
- Support 8 CS(depend on SoCs)
Limitations:
- No support for the ecc step size is 512.
- Untested on some SoCs.
- No support for subpages.
- No support for the builtin randomizer.
- The original bad block mask is not supported. It is recommended to
use the BBT(bad block table).
Signed-off-by: Yifeng Zhao <yifeng.zhao@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Replace msleep occurences by udelay.
drivers/pci/pcie_dw_rockchip.c:254:3: warning: implicit
declaration of function 'msleep' [-Wimplicit-function-declaration]
Cc: Patrick Wildt <patrick@blueri.se>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Use the generic error number instead of specific error number.
Changes fix the below error.
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_read':
drivers/pci/pcie_dw_rockchip.c:70:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
70 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
drivers/pci/pcie_dw_rockchip.c: In function 'rk_pcie_write':
drivers/pci/pcie_dw_rockchip.c:90:10: error: 'PCIBIOS_UNSUPPORTED'
undeclared (first use in this function)
90 | return PCIBIOS_UNSUPPORTED;
| ^~~~~~~~~~~~~~~~~~~
Cc: Patrick Wildt <patrick@blueri.se>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Patrick Wildt <patrick@blueri.se>
Signed-off-by: Anand Moon <linux.amoon@gmail.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
RK3568 is a high-performance and low power quad-core application
processor designed for personal mobile internet device and AIoT
equipments.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Add the driver for rk3568 u-boot to get sdram capacity.
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
fdtoverlay (pxe_utils) require define fdtoverlay_addr_r env variable
for example sunxi-common.h meson64.h already have it.
Signed-off-by: Artem Lapkin <art@khadas.com>
Reviewed-by: Kever Yang <kever.yang@rock-chips.com>
Enable the SDMMC2 device tree node, as well as the pins it uses, in
U-Boot SPL.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Enable the SDMMC2 eMMC high-speed DDR mode as it is done in the
corresponding Linux kernel device tree.
Signed-off-by: Grzegorz Szymaszek <gszymaszek@short.pl>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Patrick Delaunay <patrick.delaunay@foss.st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
