- Fix USB support for rk3399 Pinebook Pro;
- Fix SPI boot for rk3399 boards other than Bob;
- Fix 32bit boards firmware build without SPL_OPTEE support;
- Fix rockchip display driver license;
onenand_probe() function is missing to set mtd->type. So set same type as
which sets onenand Linux kernel driver.
After this change 'mtd list' prints correct type instead of 'Unknown'.
Signed-off-by: Pali Rohár <pali@kernel.org>
set_gpmc_cs0() sets wrong timings and size for Nokia N900 onenand flash.
Fix that by setting the correct timings and size from the board code
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Tested-by: Pali Rohár <pali@kernel.org>
Include emmc/nand suffix into bootmenu script names and fix leaking sleep
processes when asynchronously waiting for them. 'wait -n' is not provided
by /bin/sh, so run script under bash.
Signed-off-by: Pali Rohár <pali@kernel.org>
After commit d5243359e1 ("OMAP24xx I2C: Add support for set-speed")
U-Boot is unstable to reset lp5523 led. That commit added pooling for i2c
poll ARDY bit which apparently is never set. It is not known what is
happening here.
Purpose of resetting lp5523 led in Nokia RX-51 code is just to turn off
very bright led which is powered on by NOLO and expects next boot image
(kernel or U-Boot) to turn it off.
After testing we observed that just disabling lp5523 led is working fine.
So as a workaround to this ARDY bit i2c issue we disable lp5523 led instead
of resetting it.
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
After commit 04a2ea248f ("mmc: disable UHS modes if Vcc cannot be
switched on and off") U-Boot started crashing on Nokia RX-51 while
initializing mmc and caused reboot loop.
It looks like that some clocks were not enabled and this patch fixes U-Boot
mmc crash.
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
By default CONFIG_LOGLEVEL seems to be set to 4 which is
too low and doesn't show dev_info/dev_notice/dev_warn
messages on console. This has been deliberately set low
globally to be conservative setting across the board due to
primary bootloader size limitations. It is best to tune
per board config as per user needs.
On K3 we have separate SPL and u-boot configs so we
can afford to set u-boot CONFIG_LOGLEVEL to 7.
On AM65 this patch causes u-boot.img size to change from
932KB to 940KB with 1 line additional print during
MMC boot. i.e. details of Net subsystem
"Net: K3 CPSW: nuss_ver: 0x6BA00102 cpsw_ver: 0x6BA80102 ale_ver: 0x00293904 Ports:1 mdio_freq:1000000"
Similar 8KB difference was seen on J721E.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Reviewed-by: Nishanth Menon <nm@ti.com>
Function twl4030_i2c_read() is like twl4030_i2c_read_u8() but instead of
single value it rather returns array of values.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Jaehoon Chung <jh80.chung@samsung.com>
With commit 6900797678 ("cros_ec: Support keyboard scanning with
EC_CMD_GET_NEXT_EVENT") check_for_keys() tries to read keyboard
strokes using EC_CMD_GET_NEXT_EVENT. But the sandbox driver does
not understand this command. We need to reply with
-EC_RES_INVALID_COMMAND to force check_for_keys() to fall back to
use EC_CMD_MKBP_STATE. Currently the driver prints
** Unknown EC command 0x67
in this case. With the patch the message is suppressed.
In a future patch we should upgrade the sandbox driver to provide
EC_CMD_GET_NEXT_EVENT support.
Fixes: 6900797678 ("cros_ec: Support keyboard scanning with EC_CMD_GET_NEXT_EVENT")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Erasing the flash can take over a second on some devices and the EC is
not responsive during this time. Update the timeout to 5 seconds to cope
with this.
Signed-off-by: Simon Glass <sjg@chromium.org>
The EC now requires that the offset field be set correctly when checking
on hash status. Update the code to handle this. Use the same message
struct in both functions to reduce stack space.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a commit tag to allow the Patchwork URL to be specified in a commit.
This can be handy for when you submit code to multiple projects but don't
want to use the -p option.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add an argument to allow specifying the the patchwork URL. This also adds
this feature to the settings file, either globally, or on a per-project
basis.
Signed-off-by: Simon Glass <sjg@chromium.org>
Add a new argument to allow the URL of the patchwork server to be
speciified. For now this is hard-coded in the main file, but future
patches will move it to the settings file.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present values from the settings file are only applied to the main
parser. With the new parser structure this means that some settings are
ignored.
Update the implementation to set defaults across the main parser and all
subparsers. Also fix up the comments, since ArgumentParser is being used
now.
Signed-off-by: Simon Glass <sjg@chromium.org>
At present patman tries to assume a default subcommand of 'send', to
maintain backwards compatibility. However it does not cope with
arguments added to the default command, so for example 'patman -t'
does not work.
Update the logic to handle this. Also update the CC command to use 'send'
explicitly, since otherwise patman gets confused with the patch-filename
argument.
Signed-off-by: Simon Glass <sjg@chromium.org>
A part of the EFI_TCG2_PROTOCOL is implemented.
A unit test is supplied.
The following bugs are fixed:
* incorrect buffer size in efi_file_setinfo() leading to creash in SCT
* a crash in UEFI selftest on the sandbox due to removed drivers
* missing newlines in log message for the UEFI RNG driver
-----BEGIN PGP SIGNATURE-----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=/DST
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc3' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc3
A part of the EFI_TCG2_PROTOCOL is implemented.
A unit test is supplied.
The following bugs are fixed:
* incorrect buffer size in efi_file_setinfo() leading to creash in SCT
* a crash in UEFI selftest on the sandbox due to removed drivers
* missing newlines in log message for the UEFI RNG driver
Since U-boot EFI implementation is getting richer it makes sense to
add support for EFI_TCG2_PROTOCOL taking advantage of any hardware TPM
available on the device.
This is the initial implementation of the protocol which only adds
support for GetCapability(). It's limited in the newer and safer
TPMv2 devices.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
A following patch introduces EFI_TCG2_PROTOCOL.
Add the required TPMv2 headers to support it.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
When copying a string with must allocate a byte for the terminating '\0' in
the target buffer.
Fixes: fbe4c7df00 ("efi_loader: enable file SetInfo()")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add missing newline to log messages in efi_rng_register() otherwise
something like below would be shown
Scanning disk virtio-blk#31...
Found 2 disks
Missing RNG device for EFI_RNG_PROTOCOLNo EFI system partition
Signed-off-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
When calling ExitBootServices during out unit tests we should not detach
devices as we need console output for runtime tests.
Fixes: 529441ca89 ("efi_loader: Disable devices before handing over control")
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Rockchip has many 32bit SoCs and some of them are support SPL_OPTEE now,
only boards with SPL_OPTEE support can fit BINMAN well, other boards
will fail at initr_binman() in U-Boot proper after below patch,
eg. rv1108 board.
83187546ae binman: Support multiple images in the library
Fixes: 79030a4861 ("rockchip: Add Single boot image (with binman, pad_cat)")
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Commit c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
added an alias spi1 referring to spi@ff1d0000, however there was already
an alias spi0 referring to the same node in rockpro64's u-boot.dtsi, and
having both aliases present broke booting from SPI flash for this board.
Remove the spi0 alias, set the default bus for SPI flash to 1, and
enable support for numbered aliases in SPL so that it uses the same bus
numbering as U-Boot proper. This fixes booting from U-Boot in SPI flash
on the rockpro64 board.
Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com>
Suggested-by: Simon Glass <sjg@chromium.org>
Fixes: c4cea2bbf9 ("rockchip: Enable building a SPI ROM image on bob")
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Commit fe97471632 ("rockchip: rk3288: Allow setting up clocks in
U-Boot proper") fixes some clock issues when chainloading U-Boot on
rk3288 chromebooks. Part of that change is still available in veyron's
board_early_init_r() function. Since chain-loading U-Boot proper from
vendor firmware is possible on gru boards as well, do the same thing for
them too.
On rk3399, this needs to detect whether SPL was run via handoff, so
enable that and bloblist kconfigs it needs for chromebook_bob.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
It's possible to chainload U-Boot proper from the vendor firmware in
rk3399 chromebooks, but the way the vendor firmware sets up clocks is
somehow different than what U-Boot expects. This causes the display to
stay devoid of content even though vidconsole claims to work (with
patches in process of being upstreamed).
This is meant to be a rk3399 version of commit d3cb46aa8c ("rockchip:
Init clocks again when chain-loading") which can detect the discrepancy,
but this patch instead checks whether SPL (and therefore the clock init)
was run via the handoff functionality and runs the init if it was not.
Signed-off-by: Alper Nebi Yasak <alpernebiyasak@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
In order to enable the Amlogic SM1 MMC controller fix, we need to add a u-boot specific
MMC controller compatible.
This adds a new meson-sm1-u-boot.dtsi and reworks the other -u-boot.dtsi
to use this for SM1 based boards.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Amlogic SM1 SoCs doesn't work over 50MHz. When phase sets to 270', it's
working fine over 50MHz on Amlogic SM1 SoCs.
Since Other Amlogic SoCs doens't report an issue, phase value is using
to 180' by default.
To distinguish which value is used adds an u-boot only sm1 compatible.
In future, it needs to find what value is a proper about each SoCs.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Anand Moon <linux.amoon@gmail.com>
Move the asm/arch-meson/sd_emmc.h to a local meson_gx_mmc.h,
remove the useless if/then and fix the meson_gx_mmc.c include.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This is a combination of upstream libfdt commits to fix warnings about
comparing signed and unsigned integers:
==========
scripts/dtc/libfdt/fdt.c: In function ‘fdt_offset_ptr’:
scripts/dtc/libfdt/fdt.c:137:18: warning: comparison between signed and unsigned integer expressions [-Wsign-compare]
if ((absoffset < offset)
...
==========
For a detailed description of the fixes, see the dtc repo:
https://git.kernel.org/pub/scm/utils/dtc/dtc.git/log/?id=73e0f143b73d808
For this patch the commits between 73e0f143b73d8088 and ca19c3db2bf62000
have been combined and adjusted for the slight differences in U-Boot's
libfdt code base.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
- Avoid using hardcoded number of variable range MTRRs in mtrr_commit()
- coral: Correct max98357 file
- coral: Update smbios tables to latest definition
The accepted binding uses multiple nodes, one for each table type. Update
coral accordingly.
Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since commit 29d2d64ed5 ("x86: Add support for more than 8 MTRRs"),
the maximum number of variable range MTRRs was increased from 8 to 10.
On the BayTrail platform there are only 8 variable range MTRRs. In
mtrr_commit() it still uses MTRR_MAX_COUNT which caused a #GP during
VESA video driver probe. It should have been updated to use dynamically
probed number.
This fixes the boot failure seen on Intel Minnow Max board.
Fixes: 29d2d64ed5 ("x86: Add support for more than 8 MTRRs")
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
The following bugs are fixed:
* The conitrace command failed to build.
* Non-volatile UEFI variables were not delete form the file store.
The following features are added:
* Support for the FN1 - FN10 keys on crosswire keyboards is added.
* An EFI binary is provided to dump the binary device tree.
tpm2_get_capability() is adjusted in preparation of the implementation
of the EFI_TCG2_PROTOCOL.
-----BEGIN PGP SIGNATURE-----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=swsS
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc2-2' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc2 (2)
The following bugs are fixed:
* The conitrace command failed to build.
* Non-volatile UEFI variables were not delete form the file store.
The following features are added:
* Support for the FN1 - FN10 keys on crosswire keyboards is added.
* An EFI binary is provided to dump the binary device tree.
tpm2_get_capability() is adjusted in preparation of the implementation
of the EFI_TCG2_PROTOCOL.
after commit 4ab3817ff1 ("clk: fixed-rate: Enable DM_FLAG_PRE_RELOC flag")
Cubieboard7 (based on actions S700 SoC) fails to boot.
It is due to the fact that the default value of CONFIG_SYS_MALLOC_F_LEN (0x400)
would not provide enough memory for clock device to probe (before relocation)
well.
This commit fixes it, by increasing SYS_MALLOC_F_LEN to value 0x2000.
Suggested-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Amit Singh Tomar <amittomer25@gmail.com>
In case there is an EEPROM attached to the KS8851 MAC and the EEPROM
contains a valid MAC address, the MAC address is loaded into the NIC
registers on power on. Read the MAC address out of the NIC registers
and provide it to U-Boot.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Eugen Hristev <eugen.hristev@microchip.com>
Cc: Joe Hershberger <joe.hershberger@ni.com>
