When booting imx8mp-evk the following allocation error
message is seen:
U-Boot 2021.01-rc3-00200-ge668bec96a5f (Dec 21 2020 - 14:36:42 -0300)
alloc space exhausted
Fix it by increasing CONFIG_SYS_MALLOC_F_LEN to 0x10000 like it
is done on other i.MX8MM/8MN boards.
Reported-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Tested-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Calling ahab_close cmd force the user to interact for confirmation.
This is not user-friendly when using this cmd during factory process.
Allow the user to pass '-y' option to bypass this confirmation.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Acked-by: Oliver Graute <oliver.graute@kococonnector.com>
The current PHY rework does the following things:
1. Configure 125MHz clock
2. Setup the TX clock delay (RX is enabled by default),
3. Setup reserved bits to avoid voltage peak
The clock delays are nowadays already configured by the
PHY driver (in ar803x_delay_config). The code for that
can simply be dropped. The clock speed can also be
configured by the PHY driver by adding the device tree
property "qca,clk-out-frequency".
What is left is setting up the undocumented reserved bits
to avoid the voltage peak problem. I slightly improved its
documentation while updating the board's PHY rework code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Instead of hardcoding index magic numbers in the board code,
also rely on board_fit_config_name_match choosing the right
config for the fitImage containing the kernel.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add a host_build() function, so that it's possible to
check for software being build with USE_HOSTCC without
relying on preprocessor conditions. In other words
#ifdef USE_HOSTCC
host_only_code();
#endif
can be written like this instead:
if (host_build())
host_only_code();
This improves code readability and test coverage and
compiler will eleminate this unreachable code.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
After the conversion to device tree the board information becomes
redundant:
Model: Freescale i.MX6 Quad Plus SABRE Smart Device Board
Board: MX6-SabreSD
Remove the printing of the board information.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
i.MX8M series includes support for high speed modes in uSDHC controllers.
Turn on corresponding configuration options for EVK boards, which would
enable high speed modes to be included in U-Boot.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
i.MX8M series provide support for high speed grades in their
usdhc controllers, which has eMMC and SDHC connected to them.
Enable this support across the entire i.MX8M family by providing quirks
to usdhc controllers designated by storage media connected to them.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Ye Li <ye.li@nxp.com>
Some SD Card controller and power circuitry has increased capacitance,
which keeps the internal logic remains powered after regulator is switch
off. This is generally the case when card is switched to SD104 mode,
where a power cycle should be performed. In case if the card internal
logic remains powered, it causes a subsequent failure of mode
transition, effectively leading to failed enumeration.
Introduce a delay of 20 msec in order to provide a possibility for
internal card circuitry to drain voltages and perform a power cycle
correctly.
Similar fix is done in commit c49d0ac38a ("ARM: dts: rmobile: Increase
off-on delay on the SD Vcc regulator") targeted Renesas SOCs.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
There have been some updates to the device tree since 5.6.
This also includes some clocks, and makes it easier to keep
board device tree files in sync with Linux
Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Peng Fan <peng.fan@nxp.com>
Fixed wrong PHY Interface Mode
As per kernel commit 0672d22a1924 ("ARM: dts: imx: Fix the AR803X phy-mode)
the correct phy-mode should be "rgmii-id", so fix it accordingly
to fix the Ethernet regression.
This problem has been exposed by commit:
commit 13114f38e2
Fix the phy-mode accordingly to fix the regression.
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Vladimir Oltean <vladimir.oltean@nxp.com>
The fsp_types.h header file contains macros for building signatures of
different widths. These signature macros are architecture agnostic,
and can be used in all places which use signatures in a data
structure. Move and rename the fsp_types.h under the common include
header.
Signed-off-by: Sughosh Ganu <sughosh.ganu@linaro.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
xFSTK sources got a new home under Edison Firmware Group on GitHub [1].
Update Intel Edison documentation accordingly.
While here, fix couple of typos.
[1]: https://github.com/edison-fw
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Acked-by: Bin Meng <bmeng.cn@gmail.com>
Travis-CI is changing their support for FOSS (understandably) to have a
limited per-month number of build minutes. Unfortunately for us, the
matrix of jobs we run will exhaust that very quickly. Remove the yml
file. Thanks for all the builds, Travis-CI!
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Since linux commit 2e6cde96873253fd9eb0f20afd8ffd18278cff75 ("arm64:
dts: ls1028a: make the eMMC and SD card controllers use fixed indices")
mmc0 is the eMMC and mmc1 is the SD card. Also swap it in u-boot to
avoid any confusion by the user and to be aligned with linux.
Signed-off-by: Michael Walle <michael@walle.cc>
* Provide a tool to create a file with UEFI variables to preseed UEFI
variable store.
* Make size of UEFI variable store configurable.
* Add man pages for commands 'bootefi' and 'button'.
-----BEGIN PGP SIGNATURE-----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=2GYO
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-01-rc4' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2021-01-rc4
* Provide a tool to create a file with UEFI variables to preseed UEFI
variable store.
* Make size of UEFI variable store configurable.
* Add man pages for commands 'bootefi' and 'button'.
tools/efivar.py allows to prepare a file with UEFI variables to preseed
the UEFI variable store.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Currently the size of the buffer to keep UEFI variables in memory is fixed
at 16384 bytes. This size has proven to be too small for some use cases.
Make the size of the memory buffer for UEFI variables customizable.
Reported-by: Paulo Alcantara (SUSE) <pc@cjr.nz>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
For the proper reboot Odroid-C4 board requires to switch TFLASH_VDD_EN
pin to the high impedance mode, otherwise the board is stuck in the
middle of loading early stages of the bootloader from SD card.
This can be achieved by using the OPEN_DRAIN flag instead if the
ACTIVE_HIGH, what will leave the pin in input to achieve high state (pin
has the pull-up) and solve the issue.
Suggested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add SPI Flash controller driver for Cortina Access
CAxxxx SoCs
Signed-off-by: Pengpeng Chen <pengpeng.chen@cortina-access.com>
Signed-off-by: Alex Nemirovsky <alex.nemirovsky@cortina-access.com>
CC: Vignesh R <vigneshr@ti.com>
CC: Tom Rini <trini@konsulko.com>
[jagan: rebase on master]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This patch adds bindings for the MMC slot and SPI flash on the Sipeed Maix
Bit.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Acked-by: Rick Chen <rick@andestech.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The designware ssi device has "broken" chip select behaviour [1], and needs
specific manipulation to use the built-in chip select. The existing fix is
to use an external GPIO for chip select, but typically the K210 has SPI3
directly connected to a flash chip with dedicated pins. This makes it
impossible to use the spi_xfer function to use spi, since the CS is
de-asserted in between calls. This patch adds an implementation of
exec_op, which gives correct behaviour when reading/writing spi flash.
This patch also rearranges the headers to conform to U-Boot style.
[1] https://lkml.org/lkml/2015/12/23/132
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This documentation has been taken from Linux commit 3d7db0f11c7a ("spi: dw:
Refactor mid_spi_dma_setup() to separate DMA and IRQ config"), immediately
before the file was deleted and replaced with a yaml version. Additional
compatible strings from newer versions have been added, as well as a few
U-Boot-specific ones.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
CTRLR0 can have several different layouts depending on the specific device
(dw-apb-ssi vs dwc-ssi), and specific parameters set during synthesis.
Update the driver to support three specific configurations: dw-apb-ssi with
SSI_MAX_XFER_SIZE=16, dw-apb-ssi with SSI_MAX_XFER_SIZE=32, and dwc-ssi.
dw-apb-ssi is the version of the device on Altera/Intel SoCFPGAs, MSCC
SoCs, and Canaan Kendryte K210 SoCs. This is the only version this driver
supported before this change. The register layout before version 3.23a is:
| 31 .. 16 |
| other stuff |
| 15 .. 10 | 9 .. 8 | 7 .. 6 | 5 .. 4 | 3 .. 0 |
| other stuff | TMOD | MODE | FRF | DFS |
Note that DFS (Data Frame Size) is only 4 bits, limiting transfers to data
frames of 16 bits or less.
In version 3.23a, the SSI_MAX_XFER_SIZE parameter was introduced. This
parameter defaults to 16 (resulting in the same layout as prior versions),
but may also be set to 32. To allow setting longer data frame sizes, a new
DFS_32 register was introduced:
| 31 .. 21 | 20 .. 16 |
| other stuff | DFS_32 |
| 15 .. 10 | 9 .. 8 | 7 .. 6 | 5 .. 4 | 3 .. 0 |
| other stuff | TMOD | MODE | FRF | all zeros |
The old DFS field no longer controls the data frame size. To detect this
layout, we try writing 0xF to DFS. If we read back 0x0, then this device
has SSI_MAX_XFER_SIZE=32.
dwc-ssi is the version of the device on Intel Keem Bay SoCs and Canaan
Kendryte K210 SoCs. The layout of ctrlr0 is:
| 31 .. 16 |
| other stuff |
| 15 .. 12 | 11 .. 10 | 9 .. 8 | 7 .. 6 | 4 .. 0 |
| other stuff | TMOD | MODE | FRF | DFS_32 |
The semantics of the fields have not changed since the previous version.
However, SSI_MAX_XFER_SIZE is effectively always 32.
To support these different layouts, we model our approach on the one
which the Linux kernel has taken. During probe, the driver calls an init
function stored in driver_data. This init function is responsible for
determining the layout of CTRLR0, and supplying the update_cr0 function.
The style of and information behind this commit is based on the Linux MMIO
driver for these devices. Specific reference was made to the series adding
support for Intel Keem Bay SoCs [1].
[1] https://lore.kernel.org/linux-spi/20200505130618.554-1-wan.ahmad.zainie.wan.mohamad@intel.com/
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This adds SoC-specific compatible strings to all users of the designware
spi device. This will allow for the correct driver to be selected for each
device. Where it is publicly documented, a compatible string for the
specific device version has also been added. Devices without
publicly-documented device versions include MSCC SoCs, and Arc Socs. All
compatible strings except those for SoCFPGAs and some of the versioned
strings have been taken from Linux.
Since SSI_MAX_XFER_SIZE is determined at runtime, this is not strictly
necessary. However, it is a good cleanup and brings things closer to Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This should reduce the size of the struct, and also groups more similar
fields together.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
A few registers had slightly different names from what is in the datasheet.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Using an fdt-specific function causes problems when compiled with a live
tree.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This property is named differently than other SPI drivers with the same
property, as well as the property as used in Linux.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Tested-by Eugeniy Paltsev <Eugeniy.Paltsev@synopsys.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
This allows different log levels to be enabled or disabled depending on the
desired level of verbosity. In particular, it allows for general debug
information to be printed while excluding more verbose logging which may
interfere with timing.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
The resting state of MOSI is high when nothing is driving it. If we drive
it low while recieving, it looks like we are transmitting 0x00 instead of
transmitting nothing. This can confuse slaves (like SD cards) which allow
new commands to be sent over MOSI while they are returning data over MISO.
The return of MOSI from 0 to 1 at the end of recieving a byte can look like
a start bit and a transmission bit to an SD card. This will cause the card
to become out-of-sync with the SPI device, as it thinks the device has
already started transmitting two bytes of a new command. The mmc-spi driver
will not detect the R1 response from the SD card, since it is sent too
early, and offset by two bits. This patch fixes transfer errors when using
SD cards with dw spi.
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
U-Boot is able to erase bad mtd blocks on raw nand devices, but this
is not true for spinand flashes. Lets enable this feature for spinand
flashes as well. This is extemelly useful for flash testing.
Signed-off-by: Mikhail Kshevetskiy <mikhail.kshevetskiy@oktetlabs.ru>
Currently when marking a block, we use spinand_erase_op() to erase
the block before writing the marker to the OOB area. Doing so without
waiting for the operation to finish can lead to the marking failing
silently and no bad block marker being written to the flash.
In fact we don't need to do an erase at all before writing the BBM.
The ECC is disabled for raw accesses to the OOB data and we don't
need to work around any issues with chips reporting ECC errors as it
is known to be the case for raw NAND.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-4-frieder.schrempf@kontron.de
When writing the bad block marker to the OOB area the access mode
should be set to MTD_OPS_RAW as it is done for reading the marker.
Currently this only works because req.mode is initialized to
MTD_OPS_PLACE_OOB (0) and spinand_write_to_cache_op() checks for
req.mode != MTD_OPS_AUTO_OOB.
Fix this by explicitly setting req.mode to MTD_OPS_RAW.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-3-frieder.schrempf@kontron.de
For reading and writing the bad block markers, spinand->oobbuf is
currently used as a buffer for the marker bytes. During the
underlying read and write operations to actually get/set the content
of the OOB area, the content of spinand->oobbuf is reused and changed
by accessing it through spinand->oobbuf and/or spinand->databuf.
This is a flaw in the original design of the SPI NAND core and at the
latest from 13c15e07eedf ("mtd: spinand: Handle the case where
PROGRAM LOAD does not reset the cache") on, it results in not having
the bad block marker written at all, as the spinand->oobbuf is
cleared to 0xff after setting the marker bytes to zero.
To fix it, we now just store the two bytes for the marker on the
stack and let the read/write operations copy it from/to the page
buffer later.
Fixes: 7529df465248 ("mtd: nand: Add core infrastructure to support SPI NANDs")
Cc: stable@vger.kernel.org
Signed-off-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20200218100432.32433-2-frieder.schrempf@kontron.de
u_boot should be u-boot
Signed-off-by: Sean Anderson <seanga2@gmail.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
According to the mx25l12805d datasheet it supports using 4K or 64K sectors.
So lets add the SECT_4K to enable 4K sector usage.
Datasheet: https://www.mxic.com.tw/Lists/Datasheet/Attachments/7321/MX25L12805D,%203V,%20128Mb,%20v1.2.pdf
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
