Add info regarding splash screen, video, bloblist and GPIO related
Kconfigs which were missing in the documentation.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium>
Fill video handoff fields in video_post_probe as at this point we have
full framebuffer-related information.
Also fill all the fields available in video hand-off struct as those
were missing earlier and U-boot framework expects them to be filled for
some of the functionalities.
While filling framebuffer size in video hand-off structure use the
actual framebuffer region size as derived from gd->video_top and
gd->video_bottom instead of directly using the size populated in
video_uc_plat as it contains unaligned size.
Reported-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Skip framebufer reservation if it was already reserved from previous
stage and whose information was passed using a bloblist.
Return error in case framebuffer information received from bloblist is
invalid i.e NULL or empty.
While at it, improve the debug message to make it more clear that
address in discussion is of framebuffer and not bloblist and also match
it with printing scheme followed in video_reserve function.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Start reservations needed for init sequence only after catching
bloblists from previous stage.
This is to avoid catching bloblists in the middle causing gaps while
u-boot is reserving.
Adjust the relocaddr as per video hand-off information received from
previous stage so that further reservations start only after regions
reserved for previous stages
Skip reservation for video memory if it was already filled by a
bloblist.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Remove video_setup from evm_init sequence since video memory is getting
called at an earlier place to make sure video memory is reserved at
the end of RAM.
Suggested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Setup video memory before page table reservation using
"spl_reserve_video_from_ram_top" which ensures framebuffer memory gets
reserved from the end of RAM.
This is done to enable the next stage to directly skip the
pre-reserved area from previous stage right from the end of RAM without
having to make any gaps/holes to accommodate those regions which was the
case before as previous stage reserved region not from the end of RAM.
Use gd->ram_top instead of local ram_top and update gd->reloc_addr after
each reservation to ensure further regions are reserved properly.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Nikhil M Jain <n-jain1@ti.com>
Add an API which enforces framebuffer reservation from end of RAM.
This is done so that next stage can directly skip this region before
carrying out further reservations.
Signed-off-by: Devarsh Thakkar <devarsht@ti.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Change spl_enable_dcache so it also enable icache on SPL
initialization for the main domain part of the boot flow. This
improves bootloader booting time.
Link: https://lore.kernel.org/all/20231109140958.1093235-1-joao.goncalves@toradex.com/
Signed-off-by: Joao Paulo Goncalves <joao.goncalves@toradex.com>
Tested-by: Nishanth Menon <nm@ti.com>
Add generic boot-flow diagrams, and SoC-specific info around build
steps.
Signed-off-by: Jai Luthra <j-luthra@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
In preparation for enabling ethernet for the am62ax family of SoCs,
introduce the initial DMA channel settings for the am62ax
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
[bb@ti.com: expanded on commit message]
Signed-off-by: Bryan Brattlof <bb@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
main_timer0 is used by u-boot as the tick-timer. Add it to the soc
devices list so it an be enabled via the k3 power controller.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Move esm-k3.txt to ti,j721e-esm.yaml in line with the devicetree
documentation in kernel.
Signed-off-by: Neha Malcom Francis <n-francis@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
BeagleBoard.org BeagleBone AI-64 is an open source hardware single
board computer based on the Texas Instruments TDA4VM SoC featuring
dual-core 2.0GHz Arm Cortex-A72 processor, C7x+MMA and 2 C66x
floating-point VLIW DSPs, 3x dual ARM Cortex-R5 co-processors,
2x 6-core Programmable Real-Time Unit and Industrial Communication
SubSystem, PowerVR Rogue 8XE GE8430 3D GPU. The board features 4GB
DDR4, USB3.0 Type-C, 2x USB SS Type-A, miniDisplayPort, 2x 4-lane
CSI, DSI, 16GB eMMC flash, 1G Ethernet, M.2 E-key for WiFi/BT, and
BeagleBone expansion headers.
This board family can be indentified by the BBONEAI-64-B0 in the
at24 eeprom:
[aa 55 33 ee 01 37 00 10 2e 00 42 42 4f 4e 45 41 |.U3..7....BBONEA|]
[49 2d 36 34 2d 42 30 2d 00 00 42 30 30 30 37 38 |I-64-B0-..B00078|]
Baseline of the devicetree is from v6.6-rc1
https://beagleboard.org/ai-64https://git.beagleboard.org/beagleboard/beaglebone-ai-64
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move the omap3 beagle to the beagle vendor folder representing
BeagleBoard.org platforms.
Suggested-by: Tom Rini <trini@konsulko.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Move beagleplay support away from ti/am62x to it's own beagle vendor
folder.
This forms the starting point for new beagle platforms added under it's
own board vendor folder.
As part of this create all the associated files with a bare minimum
beagleplay.c file.
Suggested-by: Andrew Davis <afd@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
[trini: Update k3-binman.dtsi to use full path to scheme.yaml now]
Signed-off-by: Tom Rini <trini@konsulko.com>
Add am62x_beagleplay_* defconfig customized for the configuration of
BeaglePlay and drop the config fragments.
This is in preparation for dropping the dependency on ti vendor folder
entirely.
Signed-off-by: Nishanth Menon <nm@ti.com>
With the upcoming folder separation, there is no further need to depend
on am625-binman.dtsi. Duplicate the existing definitions to u-boot.dtsi
and r5.dts as appropriate.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Bryan Brattlof <bb@ti.com>
When using include directives within a section that is included by non
TI board rst file, k3.rst and other include paths need to be relative to
doc/board/ base.
Signed-off-by: Nishanth Menon <nm@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Kernel commit 1b77265626a4 ("arm64: dts: ti: k3-j7200-mcu-wakeup: Add
HyperBus node") was merged to kernel without its dependent patch [1].
Similar fix is needed in U-Boot, and hbmc currently breaks boot. Till
this gets fixed in U-Boot, disable the config by default so that the
hbmc probe that happens in board/ti/j721e/evm.c will not take place
and lead to boot failure.
This is similar to the approach in commit 5b2671594b ("configs:
j721e: Remove HBMC_AM654 config"), introduced to j7200 evm platform.
[1] https://lore.kernel.org/all/20230424184810.29453-1-afd@ti.com/
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Commit 5019170970 ("arch: arm: mach-k3: j721e: add support for UDA
FS") introduced basic UDA FS support, however, we can Take approach
similar to commit 0f1c1e8b36 ("arm: mach-k3: am625: Add support for
UDA FS"). While boot partition support with EMMC boot is useful, it is
constrained by the size of boot hardware partition itself.
In the case of K3 devices, tispl images can contain OP-TEE images that
can substantially vary in size and the u-boot image itself can vary over
time as we enable various features.
So use the CSD information in the case of EMMC_BOOT configuration being
enabled to pick boot partition or UDA FS mode operation to pick.
If EMMC_BOOT is disabled, then depend on filesystem configuration to
pick data from UDA.
Signed-off-by: Nishanth Menon <nm@ti.com>
Enable SOC_K3_J721E_J7200 when board is J7200 EVM - this allows us to
differentiate J7200 platform cleanly in board independent codebase.
Signed-off-by: Nishanth Menon <nm@ti.com>
J7200 shares quite a few characteristics with J721E. However a few sets
are different. Introduce a Kconfig to differentiate the two to allow for
new boards to be introduced in a seamless manner.
Signed-off-by: Nishanth Menon <nm@ti.com>
Switch to using bootstd. Note with this change, we will stop using
distro_bootcmd and instead depend entirely on bootflow method of
starting the system up.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
Add explicit boot_targets to indicate the specific boot sequence to
follow.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
When config is enabled, the esm dt probe makes sense. Simplify by
dropping board specific checks.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Neha Malcom Francis <n-francis@ti.com>
This file is used to emulate customer keys on TI development board
ecosystems, move it out of board/ directory and into mach-k3. And
change the relative paths to absolute paths in the binman paths.
While at it, drop the reference in verdin-binman file which is
redundant.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Acked-by: Manorit Chawdhry <m-chawdhry@ti.com>
This file is common for all of K3, move it out of board/ directory and
into mach-k3. And change the relative paths to absolute paths in the
binman paths.
While at it, drop the reference in verdin-binman file which is
redundant.
Signed-off-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviewed-by: Andrew Davis <afd@ti.com>
SYSFW is only ever loaded by the R5 core, move the code into that
directory. While here also move the related Kconfig symbols.
Signed-off-by: Andrew Davis <afd@ti.com>
The kconfig option SPL means this build supports SPL but not that
this build is SPL, nor that this build is the SPL running on R5.
For options that are for R5 SPL use CPU_V7R.
Signed-off-by: Andrew Davis <afd@ti.com>
This makes it clear these are only to be used by the R5 builds of SPL.
And this will be used to later more cleanly split the two builds.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
Currently each set of board targets from a vendor is selected inside
the board directory for that vendor. This has the problem of multiple
targets, one from each vendor, being selectable at the same time.
For instance you can select both TARGET_AM654_A53_EVM and
TARGET_IOT2050_A53 in the same build.
To fix this we need to move the target board choice to a common location
for each parent SoC selection. Do this in arch/arm/mach-k3.
Signed-off-by: Andrew Davis <afd@ti.com>
