The environment storage location is selectable via Kconfig. We support
eMMC, SD and SPI-NOR as location for U-Boot. This adds support to store
the environment in the SPI-NOR additional to the default eMMC location.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The VCC_SD and VCC_SDIO rail should only be powered up to 3.0V on RK3399
platforms.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
pinctrl/rockchip.h provides defines that map pin numbers to pin names.
Use them to make the dts more human readable.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
This change updates the USB configuration for the RK3399-Q7 in the DTS:
* fixes the OTG board configuration by enabling it ('okay')
* improves the speed of 'usb start' by disabling the unused EHCI/OHCI
controllers
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
To correctly model the usbhub_enable regulator for U-Boot, we need
to change the settings to:
* the GPIO polarity is GPIO_ACTIVE_LOW
* should be set to inactive (enable-active-low) when boot-on settings
are applied
* it can be changed at runtime (i.e. remove the always-on)
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
The fixed regulator for overriding BIOS_DISABLE had been modelling
backwards (i.e. the GPIO polarity and the enable-active-low/high
property had both been inverted), causing the 'regulator' command
to always print/expect 'disabled'/'enabled' backwards.
This fixes the mix-up and models it correctly:
* the GPIO is low-active
* the regulator should be enabled (enable-active-high) during
boot-on initialisation
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Tested-by: Klaus Goger <klaus.goger@theobroma-systems.com>
All Rockchip SoCs use 32KB as CONFIG_ENV_SIZE.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Using the ENV offset from rockchip legacy U-Boot for all SoCs,
the offset is 4MB-32KB
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
We use the same default ENV setting in rockchip_common.h for all SoC.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
U-Boot bundles a patched copy of libfdt, so it's wrong to attempt to
include it <like/this>. This breaks the build for me when I have dtc
fully installed in my host -- as happened earlier tonight with
Buildroot, for example.
There are several other occurrences throughout the code where '<libfdt'
matches. I'm not modifying these because I have no clue why the
<systemwide> include style is being used -- IMHO wrongly.
Signed-off-by: Jan Kundrát <jan.kundrat@cesnet.cz>
The check in part_get_info_extended() for a successful partition
searching misses a condition for extended partition. In case of
(ext_part_sector == 0), we should anyway mark the partition as found,
even if it's an extended partition, i.e. (is_extended(pt->sys_ind) == 0).
Otherwise, the extended partition (type 0x0f) will never be identified,
and the following recursive call to part_get_info_extended() will get a
wrong 'part_num' and 'which_part' parameter. In the end, all those
partitions in extended table will not be identified.
Let's add the missing OR condition of (ext_part_sector == 0) for
is_extended() check to fix the problem.
The issue is discovered by running fastboot flash to an extended
partition on eMMC.
$ fastboot flash mmcsda5 cache.img
target reported max download size of 536870912 bytes
sending 'mmcsda5' (18796 KB)...
OKAY [ 2.144s]
writing 'mmcsda5'...
FAILED (remote: cannot find partition)
finished. total time: 2.261s
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Before this patch one could receive following errors when executing
"gpt write" command on machine with cache enabled:
display5 factory > gpt write mmc ${mmcdev} ${partitions}
Writing GPT:
CACHE: Misaligned operation at range [4ef8f7f0, 4ef8f9f0]
CACHE: Misaligned operation at range [4ef8f9f8, 4ef939f8]
CACHE: Misaligned operation at range [4ef8f9f8, 4ef939f8]
CACHE: Misaligned operation at range [4ef8f7f0, 4ef8f9f0]
success!
To alleviate this problem - the calloc()s have been replaced with
malloc_cache_aligned() and memset().
After those changes the buffers are properly aligned (with both start
address and size) to SoC cache line.
Signed-off-by: Lukasz Majewski <lukma@denx.de>
This function is called when signing configuration nodes. Adjust
the error message.
I do not know why we do not need to show the error message in case of
ENOSPC. Remove the if-conditional that seems unnecessary.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
If -K option is missing when you sign image nodes, it fails with
an unclear error message:
tools/mkimage Can't add hashes to FIT blob: -1
It is hard to figure out the cause of the failure.
In contrast, when you sign configuration nodes, -K is optional because
fit_config_process_sig() returns successfully if keydest is unset.
Probably this is a preferred behavior when you want to update FIT with
the same key; you do not have to update the public key in this case.
So, this commit changes fit_image_process_sig() to continue signing
without keydest. If ->add_verify_data() fails, show a clearer error
message, which has been borrowed from fit_config_process_sig().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
The "algo_name" points to a property in a blob being edited. The
pointer becomes stale when fit_image_write_sig() inserts signatures.
Then crypto->add_verify_data() writes wrong data to the public key
destination.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
test_gpt generates a persistent disk image which can be re-used across
multiple test runs. Currently, if the Python code that generates the disk
image change, the image is not regenerated, which could cause test
failures e.g. if a test was updated to expect some new partition name or
size, yet the persistent disk image contained the old name or size. This
change introduces functionality to regenerate the disk image if the
instructions to generate the image have changed.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The fw_env utility family has a default environment compiled in
which ties it quite strongly to the U-Boot source/config it has
been built with. Allow to display the U-Boot version it has been
built with using the -v/--version argument.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Designated initializers are more readable because we do not
have to check the order in the struct definitions.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
As part of my usual round of build testing, output about missing
MAINTAINERS information was not logged, and thus often overlooked.
Correct that mistake by ensuring that I log the output of
genboardscfg.py every time. As part of that, address a number of
missing MAINTAINERS entires. In the case of a missing file, I have put
the original submitter down. In the rest of the cases I have added the
config (and sometimes relevant header file) to the existing set of file
globs.
Signed-off-by: Tom Rini <trini@konsulko.com>
Looking at the schematic, LDO15 and LDO17 are tied as a power source of a
builtin network chipset. The voltage on LDO15 is corrected to 3.3V and the
name of LDO17 is corrected to "vdd_ldo17".
Signed-off-by: Dongjin Kim <tobetter@gmail.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Signed-off-by: Minkyu Kang <mk7.kang@samsung.com>
We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.
Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>
The patch:
"dm: ahci: Unwind the confusing init code"
(sha1: 7cf1afce7f)
introduce bug for ceva sata because port didn't start.
On the other hand the dwc_ahci.c was fixed correctly.
Do the same change for ceva too.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Tested-by: Mian Yousaf Kaukab <yousaf.kaukab@suse.com>
The RK3368-uQ7 uses a KSZ9031 PHY on-module. Enable PHY_MICREL_KSZ90X1
in the associated defconfig.
References: da3b9e7f ("Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The RK3368-uQ7 uses a KSZ9031 PHY on-module. Enable PHY_MICREL_KSZ90X1
in the associated defconfig (this somehow got lost with da3b9e7f).
References: da3b9e7f ("Move PHY_MICREL and PHY_MICREL_KSZ90X1 to Kconfig")
Signed-off-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Remove CONFIG_ENV_OFFSET for there already have one in rockchip_common.h
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
The API for get priv pointer is wrong, fix it.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Init the CPU and its buses to speed up the boot time.
Move rkclk_init() to a place after rk3399_configure_cpu has defined
at the same time, or else there will be a warning.
Signed-off-by: Kever Yang <kever.yang@rock-chips.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
BOOT_TARGET_DEVICES should only be added if the corresponding u-boot
command is enabled.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
rockchip-common.h already defines values that are missing from
rk3368_common.h
For example BOOT_TARGET_DEVICES was defined empty and therefore
distroboot had no boot targets.
Signed-off-by: Klaus Goger <klaus.goger@theobroma-systems.com>
Acked-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Reviewed-by: Philipp Tomsich <philipp.tomsich@theobroma-systems.com>
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Inside setup_sata() there is a cpu type check, so there is no need to
do this check in the board file.
This also brings the benefit to allowing setup_sata() to be called for the
mx6qp wandboard variant.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Enable UMS and DFU, so that the eMMC can be accessed via the
USB gadget port on the board.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Stefano Babic <sbabic@denx.de>
Since DM_USB enabled, no need the usb code in board file.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <fabio.estevam@nxp.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Commit 001cdbbb32 ("imx: mx6slevk: enable more DM drivers") breaks
MMC support in U-Boot proper on the mx6slevk_spl_defconfig target:
U-Boot SPL 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18)
Trying to boot from MMC1
U-Boot 2017.09-00396-g6ca43a5 (Oct 01 2017 - 16:20:18 -0300)
CPU: Freescale i.MX6SL rev1.0 792 MHz (running at 396 MHz)
CPU: Commercial temperature grade (0C to 95C) at 33C
Reset cause: POR
Board: MX6SLEVK
I2C: ready
DRAM: 1 GiB
MMC: FSL_SDHC: 0
MMC Device 1 not found
*** Warning - No MMC card found, using default environment
As mx6slevk_spl_defconfig does not use CONFIG_DM_MMC and its
board file does not register the mmc controller for U-Boot proper,
let's fix this by adding CONFIG_DM_MMC=y and device tree support.
While at it, add more DM drivers, so that it becomes closer to
mx6slevk_defconfig.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Add support for the latest MX6QP wandboard variant.
Based on Richard Hu's work from Technexion's U-Boot tree.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
On Vybrid SoCs U-Boot gets loaded into GFX SRAM which is 512KiB.
Currently 32KiB is reserved for the IMX header. However, this is
not reflected in the size limit. In v2017.11-rc2 the actual size
limit (512KiB-32KiB) has been reached for Colibri VF61, which
lead to a successful build of U-Boot but not a working binary.
The IMX header is much smaller than 32KiB, typically around 1KiB.
Decrease the reserved size to 4KiB and specify the correct U-Boot
size limit. Apply this new base address and limit for all Vybrid
based boards.
Signed-off-by: Stefan Agner <stefan.agner@toradex.com>
