Commit graph

60 commits

Author SHA1 Message Date
Shaohui Xie
b24f6d401c powerpc/b4860qds: add workaround for XFI
XFI does not work stable on current board, it's due to heat sink issue,
to make it work stable the board needs additional heat sink, enable two
XFI lanes only. Right now we do not have such an erratum for the issue,
so use a define CONFIG_SYS_FSL_B4860QDS_XFI_ERR to identify it.
The workaround will only be used in XFI protocols and only if the
hwconfig indicates that XFI is prefered.

A new VSC3308 config function is used instead of re-use the original
function, to avoid making the function complex and ugly.

Signed-off-by: Shaohui Xie <Shaohui.Xie@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:13 -08:00
Zhao Qiang
e7f533cd59 powerpc/mpc85xx: modify erratum A007186
T2080 v1.0 has this errata while v1.1 has fixed
this errata by hardware, add a new function has_errata_a007186
to check the SVR_SOC_VER, SVR_MAJ and SVR_MIN first,
if the sil has errata a007186, then run the errata code,
if not, doesn't run the code.

Signed-off-by: Zhao Qiang <B45475@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:09 -08:00
Prabhakar Kushwaha
31530e0b8a board/t104xrdb: Conditional workaround of errata A-008044
Workaround of Errata A-008044 was implemented without errata number and it is
enabled by default. Errata A-008044 is only valid for T1040 Rev 1.0.

So put errata number and make it conditional.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:09 -08:00
Prabhakar Kushwaha
9f074e67f5 powerpc/mpc85xx:Put errata number for T104x NAND boot issue
When device is configured to load RCW from NAND flash IFC_A[16:31] are driven
low after RCW loading. Hence Devices connected on IFC_CS[1:7] and using
IFC_A[16:31] lines are not accessible.

Workaround is already in-place.
Put the errata number to adhere errata handling framework.

Signed-off-by: Prabhakar Kushwaha <prabhakar@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-12-05 08:06:08 -08:00
Nikhil Badola
f3dff695e1 drivers : usb: fsl: Implement usb Erratum A007798 workaround
Set TXFIFOTHRESH to adjust ddr pipeline delay for successful large
usb writes

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-24 09:27:04 -08:00
Nikhil Badola
c26c80a1a4 drivers: usb: fsl: Move USB Errata checking code
Move USB Errata checking code from "arch/powerpc" to architecture independent
file "fsl_usb.h" so that errata(s) become independent of the architecture.
For each erratum checking function for PPC arch, define a nop function for
non PPC arch for successful compilation in either case

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-11-21 09:28:28 -08:00
Shaveta Leekha
b6808cd82d powerpc/serdes: Add the workaround for erratum A-007186
SerDes PLL is calibrated at reset. When the junction temperature
delta from the time the PLL is calibrated exceeds +56C/-66C,
jitter may increase and can cause PLL to unlock.

This workaround overwrite the SerDes registers with new values,
to calibrate SerDes registers.
These values are known to work fine for all temperature ranges.

This workaround is valid for B4, T4 and T2 platforms, so
added in their config.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Signed-off-by: Poonam Aggrwal <Poonam.Aggrwal@freescale.com>
[York Sun: replaced typedef ccsr_sfp_regs_t with struct ccsr_sfp_regs]
Reviewed-by: York Sun <yorksun@freescale.com>
2014-06-05 13:45:07 -07:00
York Sun
9855b3beca powerpc/mpc85xx: Add workaround for DDR erratum A004508
When the DDR controller is initialized below a junction temperature of
0°C and then operated above a junction temperature of 65°C, the DDR
controller may cause receive data errors, resulting ECC errors and/or
corrupted data. This erratum applies to the following SoCs and their
variants: MPC8536, MPC8569, MPC8572, P1010, P1020, P1021, P1022, P1023,
P2020.

Signed-off-by: York Sun <yorksun@freescale.com>
2014-06-05 13:45:07 -07:00
Chunhe Lan
f1a96ec1a9 fsl/pci: Add workaround for erratum A-005434
By default, all PEX inbound windows PEX_PEXIWARn[TRGT] are
mapped to 0xF, which is local memory. But for BSC9132, 0xF
is CCSR, 0x0 is local memory.

Signed-off-by: Minghuan Lian <Minghuan.Lian@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-05-16 16:24:26 -05:00
York Sun
c3678b0937 powerpc/mpc85xx: Add workaround for erratum A007212
Erratum A007212 for DDR is about a runaway condition for DDR PLL
oscilliator. Please refer to erratum document for detail.
For this workaround to work, DDR PLL needs to be disabled in RCW.
However, u-boot needs to know the expected PLL ratio. We put the
ratio in a reserved field RCW[18:23]. U-boot will skip this workaround
if DDR PLL ratio is set, or the reserved field is not set.

Workaround for erratum A007212 applies to selected versions of
B4/T4 SoCs. It is safe to apply the workaround to all versions. It
is helpful for upgrading SoC without changing u-boot. In case DDR
PLL is disabled by RCW (part of the erratum workaround), we need this
u-boot workround to bring up DDR clock.

Signed-off-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Nikhil Badola
11856919f2 fsl/usb: Workaround for USB erratum-A007075
Put a delay of 5 millisecond after reset so that ULPI phy
gets enough time to come out of reset. Erratum A007075 applies
to following SOCs and their variants, if any
        P1010 rev 1.0
        B4860 rev 1.0, 2.0
        P4080 rev 2.0, 3.0

Signed-off-by: Nikhil Badola <nikhil.badola@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-04-22 17:58:48 -07:00
Suresh Gupta
9c641a872a powerpc/usb: Workaround for erratum-A006261
USB spec says that the minimum disconnect threshold should be
	over 525 mV. However, internal USB PHY threshold value is below
	this specified value. Due to this some devices disconnect at
	run-time. Hence, phy settings are tweaked to increased disconnect
	threshold to be above 525mV by using this workaround.

Signed-off-by: Suresh Gupta <suresh.gupta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-03-07 14:52:16 -08:00
Shaveta Leekha
7af9a07403 powerpc/b4860: Add workaround for errata A006384 and A006475
SerDes PLLs may not lock reliably at 5 G VCO configuration(A006384)
and at cold temperatures(A006475), workaround recalibrate the
PLLs with some SerDes configuration

Both these errata are only applicable for b4 rev1.
So, make workaround for these errata conditional,
depending upon soc version.

Signed-off-by: Shaveta Leekha <shaveta@freescale.com>
Reviewed-by: York Sun <yorksun@freescale.com>
2014-03-07 14:52:01 -08:00
York Sun
b518816423 powerpc/mpc85xx: Fix a typo in workaround message for DDR erratum A003474
Unfortunately a typo presents "DDR-A003473" instead of "DDR-A003474".

Signed-off-by: York Sun <yorksun@freescale.com>
2014-01-21 13:40:18 -08:00
York Sun
133fbfa9e6 powerpc/mpc85xx: Add workaround for erratum A006379
Erratum A006379 says CPCHDBCR0 bit field [10:14] has incorrect default
value after POR. The workaround is to set this field before enabling
CPC to 0x1e.

Erratum A006379 applies to
	T4240 rev 1.0
	B4860 rev 1.0, 2.0

Signed-off-by: York Sun <yorksun@freescale.com>
2013-10-16 16:15:17 -07:00
York Sun
954a1a4776 powerpc/mpc85xx: Add workaround for erratum A-005125
In a very rare condition, a system hang is possible when the e500 core
initiates a guarded load to PCI / PCIe /SRIO performs a coherent write
to memory. Please refer to errata document for more details. This erratum
applies to the following SoCs and their variants, if any.

BSC9132
BSC9131
MPC8536
MPC8544
MPC8548
MPC8569
MPC8572
P1010
P1020
P1021
P1022
P1023
P2020
C29x

Signed-off-by: York Sun <yorksun@freescale.com>
CC: Scott Wood <scottwood@freescale.com>
2013-09-10 14:31:47 -07:00
Tom Rini
6612ab3395 Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx 2013-08-21 16:27:47 -04:00
Shengzhou Liu
424bf94273 powerpc/sec: Add workaround for SEC A-003571
Multiple read/write transactions initiated by security
engine may cause system to hang.
Workaround: set MCFGR[AXIPIPE] to 0 to avoid hang.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Acked-by: York Sun <yorksun@freescale.com>
2013-08-20 10:47:07 -07:00
Chunhe Lan
9c3f77eb3b fsl_i2c: add workaround for the erratum I2C A004447
This workaround is for the erratum I2C A004447. Device reference
manual provides a scheme that allows the I2C master controller
to generate nine SCL pulses, which enable an I2C slave device
that held SDA low to release SDA. However, due to this erratum,
this scheme no longer works. In addition, when I2C is used as
a source of the PBL, the state machine is not able to recover.

At the same time, delete the reduplicative definition of SVR_VER
and SVR_REV. The SVR_REV is the low 8 bits rather than the low 16
bits of svr. And we use the CONFIG_SYS_FSL_A004447_SVR_REV macro
instead of hard-code value 0x10, 0x11 and 0x20.

The CONFIG_SYS_FSL_A004447_SVR_REV = 0x00 represents that one
version of platform has this I2C errata. So enable this errata
by IS_SVR_REV(svr, maj, min) function.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Heiko Schocher <hs@denx.de>
2013-08-20 11:15:31 +02:00
York Sun
d217a9ad01 powerpc/mpc85xx: Workaround for A-005812
Erratum A-005812 Incorrect reservation clearing in Write Shadow mode can
result in invalid atomic operations. For u-boot, this erratum only impacts
SoCs running in write shadow mode.

Signed-off-by: York Sun <yorksun@freescale.com>
2013-08-09 12:41:40 -07:00
Wolfgang Denk
1a4596601f Add GPL-2.0+ SPDX-License-Identifier to source files
Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>
2013-07-24 09:44:38 -04:00
Scott Wood
8212519254 powerpc/mpc85xx: work around erratum A-006593
Erratum A-006593 is "Atomic store may report failure but still allow
the store data to be visible".

The workaround is: "Set CoreNet Platform Cache register CPCHDBCR0 bit
21 to 1'b1.  This may have a small impact on synthetic write bandwidth
benchmarks but should have a negligible impact on real code."

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-06-20 17:08:49 -05:00
Xulei
99d7b0a43d powerpc/85xx: Add workaround for errata USB-14 (enable on P204x/P3041/P50x0)
On P204x/P304x/P50x0 Rev1.0, USB transmit will result in false internal
multi-bit ECC errors, which has impact on performance, so software should
disable all ECC reporting from USB1 and USB2.

In formal release document, the errata number should be USB14 instead of USB138.

Signed-off-by: xulei <Lei.Xu@freescale.com>
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: xulei <B33228@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-05-02 16:56:44 -05:00
Shengzhou Liu
72bd83cd0a powerpc/t4240: Adding workaround errata A-005871
When CoreNet Fabric (CCF) internal resources are consumed by the cores,
inbound SRIO messaging traffic through RMan can put the device into a
deadlock condition.

This errata workaround forces internal resources to be reserved for
upstream transactions. This ensures resources exist on the device for
upstream transactions and removes the deadlock condition.

The Workaround is for the T4240 silicon rev 1.0.

Signed-off-by: Shengzhou Liu <Shengzhou.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2013-01-30 11:25:15 -06:00
Yuanquan Chen
c0a4e6b889 powerpc/p4080ds: fix PCI-e x8 link training down failure
Due to SerDes configuration error, if we set the PCI-e controller link width
as x8 in RCW and add a narrower width(such as x4, x2 or x1) PCI-e device to
PCI-e slot, it fails to train down to the PCI-e device's link width. According
to p4080ds errata PCIe-A003, we reset the PCI-e controller link width to x4 in
u-boot. Then it can train down to x2 or x1 width to make the PCI-e link between
RC and EP.

Signed-off-by: Yuanquan Chen <B41889@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:28:07 -06:00
Timur Tabi
d607b9684b powerpc/85xx: implement check for erratum A-004580 work-around
The work-around for erratum A-004580 ("Internal tracking loop can falsely
lock causing unrecoverable bit errors") is implemented via the PBI
(pre-boot initialization code, typically attached to the RCW binary).
This is because the work-around is easier to implement in PBI than in
U-Boot itself.

It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied.  For A-004580, we can do this by verifying
that the values in the specific registers that the work-around says to
update.

This change requires access to the SerDes lane sub-structure in
serdes_corenet_t, so we make it a named struct.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:28:07 -06:00
Timur Tabi
0118033b67 powerpc/85xx: implement check for erratum A-004849 work-around
The work-around for erratum A-004849 ("CoreNet fabric (CCF) can exhibit a
deadlock under certain traffic patterns causing the system to hang") is
implemented via the PBI (pre-boot initialization code, typically attached
to the RCW binary).  This is because the work-around is easier to implement
in PBI than in U-Boot itself.

It is still useful, however, for the 'errata' command to tell us whether
the work-around has been applied.  For A-004849, we can do this by verifying
that the values in the specific registers that the work-around says to
update.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-11-27 18:28:06 -06:00
York Sun
a1d558a20f powerpc/mpc85xx: Add workaround for DDR erratum A004934
After DDR controller is enabled, it performs a calibration for the
transmit data vs DQS paths. During this calibration, the DDR controller
may make an inaccurate calculation, resulting in a non-optimal tap point.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:29 -05:00
York Sun
eb53941206 powerpc/mpc85xx: software workaround for DDR erratum A-004468
Boot space translation utilizes the pre-translation address to select
the DDR controller target. However, the post-translation address will be
presented to the selected DDR controller. It is possible that the pre-
translation address selects one DDR controller but the post-translation
address exists in a different DDR controller when using certain DDR
controller interleaving modes. The device may fail to boot under these
circumstances. Note that a DDR MSE error will not be detected since DDR
controller bounds registers are programmed to be the same when configured
for DDR controller interleaving.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:28 -05:00
Liu Gang
d59c557049 powerpc/srio: Workaround for srio erratrm a004034
Erratum: A-004034
Affects: SRIO

Description: During port initialization, the SRIO port performs
lane synchronization (detecting valid symbols on a lane) and
lane alignment (coordinating multiple lanes to receive valid data
across lanes). Internal errors in lane synchronization and lane
alignment may cause failure to achieve link initialization at
the configured port width.

An SRIO port configured as a 4x port may see one of these scenarios:

1.	One or more lanes fails to achieve lane synchronization.
	Depending on which lanes fail, this may result in downtraining
	from 4x to 1x on lane 0, 4x to 1x on lane R (redundant lane).

2.	The link may fail to achieve lane alignment as a 4x, even
	though all 4 lanes achieve lane synchronization, and downtrain
	to a 1x. An SRIO port configured as a 1x port may fail to complete
	port initialization (PnESCSR[PU] never deasserts) because of
	scenario 1.

Impact: SRIO port may downtrain to 1x, or may fail to complete
link initialization. Once a port completes link initialization
successfully, it will operate normally.

Signed-off-by: Liu Gang <Gang.Liu@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 14:31:12 -05:00
Zang Roy-R61911
4e0be34a85 P4080/esdhc: make the P4080 ESDHC13 errata workaround conditional
P4080 Rev3.0 fixes ESDHC13 errata, so update the code to make the
workaround conditional.
In formal release document, the errata number should be ESDHC13 instead
of ESDHC136.

Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-10-22 03:04:28 -05:00
Scott Wood
33eee330cc powerpc/fsl-corenet: work around erratum A004510
Erratum A004510 says that under certain load conditions, modified
cache lines can be discarded, causing data corruption.

To work around this, several CCSR and DCSR register updates need to be
made in a careful manner, so that there is no other transaction in
corenet when the update is made.

The update is made from a locked cacheline, with a delay before to flush
any previous activity, and a delay after to flush the CCSR/DCSR update.
We can't use a readback because that would be another corenet
transaction, which is not allowed.

We lock the subsequent cacheline to prevent it from being fetched while
we're executing the previous cacheline.  It is filled with nops so that a
branch doesn't cause us to fetch another cacheline.

Ordinarily we are running in a cache-inhibited mapping at this point, so
we temporarily change that.  We make it guarded so that we should never
see a speculative load, and we never do an explicit load.  Thus, only the
I-cache should ever fill from this mapping, and we flush/unlock it
afterward.  Thus we should avoid problems from any potential cache
aliasing between inhibited and non-inhibited mappings.

NOTE that if PAMU is used with this patch, it will need to use a
dedicated LAW as described in the erratum.  This is the responsibility
of the OS that sets up PAMU.

Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 12:16:54 -05:00
York Sun
57125f222e powerpc/mpc85xx: Make NMG_CPU_A011 workaround conditional
This erratum applies to the following SoCs:
P4080 rev 1.0, 2.0, fixed in rev 3.0
P2041 rev 1.0, 1.1, fixed in rev 2.0
P3041 rev 1.0, 1.1, fixed in rev 2.0.

Workaround for erratum NMG_CPU_A011 is enabled by default. This workaround
may degrade performance. P4080 erratum CPU22 shares the same workaround.
So it is always enabled for P4080. For other SoCs, it can be disabled by
hwconfig with syntax:

fsl_cpu_a011:disable

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Andy Fleming <afleming@freescale.com>
2012-08-23 10:24:13 -05:00
York Sun
5e23ab0a31 powerpc/mpc85xx: Workaround for erratum CPU_A011
Erratum NMG_CPU_A011 applies to P4080 rev 1.0, 2.0, fixed in rev 3.0.
It also applies to P3041 rev 1.0, 1.1, P2041 rev 1.0, 1.1. It shares the
same workaround as erratum CPU22. Rearrange registers usage in assembly
code to avoid accidental overwriting.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
48f6a5c348 powerpc/mpc85xx: Ignore E bit for SVR_SOC_VER()
We don't care E bit of SVR in most cases. Clear E bit for SVR_SOC_VER().
This will simplify the coding. Use IS_E_PROCESSOR() to identify SoC with
encryption. Remove all _E entries from SVR list and CPU list.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
1e9ea85f7d powerpc/P4080: Check SVR for CPU22 workaround
Workaround for erratum CPU22 applies to P4080 rev 1 and rev 2 only.

Signed-off-by: York Sun <yorksun@freescale.com>
2012-07-06 17:30:33 -05:00
York Sun
4108508a96 powerpc/85xx: Add workaround for erratum A-003474
Erratum A-003474: Internal DDR calibration circuit is not supported

Impact:
Experience shows no significant benefit to device operation with
auto-calibration enabled versus it disabled. To ensure consistent timing
results, Freescale recommends this feature be disabled in future customer
products. There should be no impact to parts that are already operating
in the field.

Workaround:
Prior to setting DDR_SDRAM_CFG[MEM_EN]=1, do the following:
1. Write a value of 0x0000_0015 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf30
2. Write a value of 0x2400_0000 to the register at offset
	CCSRBAR + DDR OFFSET + 0xf54

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:06 -06:00
Kumar Gala
43f082bb7f powerpc/85xx: Add workaround for erratum CPU-A003999
Erratum A-003999: Running Floating Point instructions requires special
initialization.

Impact:
Floating point arithmetic operations may result in an incorrect value.

Workaround:
Perform a read modify write to set bit 7 to a 1 in SPR 977 before
executing any floating point arithmetic operation. This bit can be set
when setting MSR[FP], and can be cleared when clearing MSR[FP].
Alternatively, the bit can be set once at boot time, and never cleared.
There will be no performance degradation due to setting this bit.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-29 08:48:05 -06:00
chenhui zhao
aada81de70 powerpc/mpc8548: Add workaround for erratum NMG_eTSEC129
Erratum NMG_eTSEC129 (eTSEC86 in MPC8548 document) applies to some early
verion silicons. This workaround detects if the eTSEC Rx logic is properly
initialized, and reinitialize the eTSEC Rx logic.

Signed-off-by: Gong Chen <g.chen@freescale.com>
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-11-08 08:30:32 -06:00
Kumar Gala
2b3a1cdd9e powerpc/mpc8548: Add workaround for erratum NMG_LBC103
The erratum NMG_LBC103 is LBIU3 in MPC8548 errata document.
Any local bus transaction may fail during LBIU resynchronization
process when the clock divider [CLKDIV] is changing. Ensure there
is no transaction on the local bus for at least 100 microseconds
after changing clock divider LCRR[CLKDIV].

Refer to the erratum LBIU3 of mpc8548.

Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:15 -05:00
Kumar Gala
5ace2992b5 powerpc/mpc8548: Add workaround for erratum NMG_DDR120
Erratum NMG_DDR120 (DDR19 in MPC8548 errata document) applies to some
early version silicons. The default settings of the DDR IO receiver
biasing may not work at cold temperature. When a failure occurs,
a DDR input latches an incorrect value. The workaround will set the
receiver to an acceptable bias point.

Signed-off-by: Gong Chen
Signed-off-by: Zhao Chenhui <chenhui.zhao@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-10-03 08:52:14 -05:00
Poonam Aggrwal
bc6bbd6be8 fsl_ifc: Add the workaround for erratum IFC A-003399(enabled on P1010)
Issue: Address masking doesn't work properly.
When sum of the base address, defined by BA, and memory bank size,
defined by AM, exceeds 4GB (0xffff_ffff) then AMASKn[AM] doesn't mask
CSPRn[BA] bits.

Impact:
This will impact booting when we are reprogramming CSPR0(BA) and
AMASK0(AMASK) while executing from NOR Flash.

Workaround:
Re-programming of CSPR(BA) and AMASK is done while not executing from NOR
Flash. The code which programs the BA and AMASK is executed from L2-SRAM.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Poonam Aggrwal
fb855f43a1 powerpc/P1010: Add workaround for erratum P1010-A003549 (related to IFC)
Issue:
Peripheral connected to IFC_CS3 may hamper booting from IFC.

Impact:
Boot from IFC may not be successful if IFC_CS3 is used.

Workaround:
If IFC_CS3 is used, gate IFC_CS3 while booting from NAND or NOR.
Also Software should select IFC_CS3 using PMUXCR[26:27] = 0x01.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Poonam Aggrwal
42aee64bd9 fsl_ifc: Add the workaround for erratum IFC-A002769 (enable on P1010)
Issue:
The NOR-FCM does not support access to unaligned addresses for 16 bit port size

Impact:
When 16 bit port size is used, accesses not aligned to 16 bit address boundary
will result in incorrect data

Workaround:
The workaround is to switch to GPCM mode for NOR Flash access.

Signed-off-by: Poonam Aggrwal <poonam.aggrwal@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-09-29 19:01:04 -05:00
Timur Tabi
da30b9fd97 powerpc/85xx: Implement work-around for P4080 erratum SERDES-A005
SerDes PLL bandwidth default setting is incorrect when no lanes are
configured as PCI Express.

Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-28 22:09:23 -05:00
Emil Medve
df8af0b4a6 p4080/serdes: Implement the XAUI workaround for SERDES9 erratum
Signed-off-by: Emil Medve <Emilian.Medve@Freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-04-27 22:29:04 -05:00
York Sun
91671913f7 powerpc/mpc85xx: implement workaround for errata DDR111 and DDR134
Workaround for the following errata:
DDR111 - MCKE signal may not function correctly at assertion of HRESET
DDR134 - The automatic CAS-to-Preamble feature of the DDR controller can
         calibrate to incorrect values

These two workarounds must be implemented together because they touch
common registers.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:13 -06:00
York Sun
eb0aff77c8 powerpc/85xx: Rename MPC8572 DDR erratum to DDR115
Use unique erratum number instead of platform number.
Enable command that reports errata on MPC8572DS.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:13 -06:00
Kumar Gala
5103a03a0b fsl_esdhc: Add the workaround for erratum ESDHC-A001 (enable on P2020)
Data timeout counter (SYSCTL[DTOCV]) is not reliable for values of 4, 8,
and 12. Program one more than the desired value: 4 -> 5, 8 -> 9, 12 -> 13.

Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-02-03 02:46:12 -06:00
York Sun
fa8d23c0ee mpc85xx: Implement workaround for erratum DDR-A003
Erratum DDR-A003 requires workaround to correctly set RCW10 for registered DIMM.
Also adding polling after enabling DDR controller to ensure completion.

Signed-off-by: York Sun <yorksun@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2011-01-19 22:58:24 -06:00