Sata/scsi and usb based devices are not started at this stage that's why
disks are not found and early update can't happen.
It is because of deficiency in the UEFI implementation which is not able to
deal with block devices which are added or removed after initialization.
EFI capsule on disk early feature needs to be fixed first to be able to
enable this feature properly.
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Enable manual start in zynqmp_qspi_fill_gen_fifo().
Also enable GQSPI_IXR_GFNFULL_MASK and check for it instead of
GQSPI_IXR_GFEMTY_MASK.
Add dummy write to genfifo register in chipselect.
Signed-off-by: Ashok Reddy Soma <ashok.reddy.soma@xilinx.com>
The default register configuration after powerup for PSSYSMON_ANALOG_BUS
register is incorrect. Hence, fix this in SPL by writing correct fixed
value. It follows UG1085 chapter 'PS SYSMON Analog_Bus' and reflects commit
sw_apps:zynq ("056ca65d44549ce27f716d423e8dfdefeee7440c")
in Xilinx:embeddedsw[1].
[1] https://github.com/Xilinx/embeddedsw
Signed-off-by: Adrian Fiergolski <adrian.fiergolski@fastree3d.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
0x04000000- 0x06000000 is reserved memory. We cannot load to anything here.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
Enable configuration options to support Turris network boot. This
includes FIT support and some crypto commands.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add nodes for SPI NOR partitions to the device tree of Turris MOX, as
are in Linux' device tree.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Stefan Roese <sr@denx.de>
Add default fdtfile environment variable with value
marvell/armada-3720-turris-mox.dtb.
This can be useful for some boot scenarios.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Configure blinking on ethernet PHY LEDs on the MOX A board when entering
rescue mode via reset button.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add necessary config options and board code to support board factory
reset / rescue mode on Turris MOX.
In order to also support invoking rescue mode from U-Boot console,
without having to press the factory reset button, put the rescue command
into `bootcmd_rescue` default environment variable. When factory reset
button is pressed, invoke rescue mode via distroboot by setting
`boot_targets` to `rescue`.
Rescue boot from console can be invoked by running
run bootcmd_rescue
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
Add nodes for indicator LED and reset button so that board code can
implement board factory reset mechanism.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Stefan Roese <sr@denx.de>
The fragmented files were not correctly read because of two issues:
- The squashfs_file_info struct has a field named 'comp', which tells if
the file's fragment is compressed or not. This field was always set to
'true' in sqfs_get_regfile_info and sqfs_get_lregfile_info. It should
actually take sqfs_frag_lookup's return value. This patch addresses
these two assignments.
- In sqfs_read, the fragments (compressed or not) were copied to the
output buffer through a for loop which was reading data at the wrong
offset. Replace these loops by equivalent calls to memcpy, with the
right parameters.
I tested this patch by comparing the MD5 checksum of a few fragmented
files with the respective md5sum output in sandbox, considering both
compressed and uncompressed fragments.
Signed-off-by: Joao Marcos Costa <jmcosta944@gmail.com>
Tested-by: Richard Genoud <richard.genoud@posteo.net>
Reviewed-by: Miquel Raynal <miquel.raynal@bootlin.com>
Documentation:
* pinmux and ums man-page
Bug fixes:
* Consider that partition numbers as hexadecimal.
* Avoid a possible NULL dereference in efi_capsule_delete_file().
-----BEGIN PGP SIGNATURE-----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=LS0d
-----END PGP SIGNATURE-----
Merge tag 'efi-2021-07-rc5' of https://source.denx.de/u-boot/custodians/u-boot-efi
Pull request for efi-2021-07-rc5
Documentation:
* pinmux and ums man-page
Bug fixes:
* Consider that partition numbers as hexadecimal.
* Avoid a possible NULL dereference in efi_capsule_delete_file().
Add support for Storopack's SMEGW01 board, which is an
IoT gateway based on the i.MX7D SoC.
Based on the original U-Boot work done by Phytec.
Signed-off-by: Fabio Estevam <festevam@denx.de>
Supported boot device types in iMX8MN: MMC, DHCP.
Add DISTRO_DEFAULTS config option and include the distro boot command
header file to enable full support of distro boot on i.MX8M Nano EVK (both
DDR and LPDDR derivatives).
Drop previous environment, which was targeting customized boot commands and
boot order.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Peng Fan <peng.fan@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Frequency requested by ddrphy_init_set_dfi_clk from fracpll uses MHZ()
macro, which expands the value provided to the Hz range without taking into
account the precise Hz setting. This causes the frequency of 266 MHz not ot
be found in the imx8mm_fracpll_tbl, since it is entered there with a
precise Hz value. This in turn causes the boot hang in SPL, as proper DDR
fracpll frequency cannot be determined.
Correct the value in imx8mm_fracpll_tbl to match the one expanded by
MHZ(266) macro, rounding it down to MHz range only.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Fixes: 825ab6b406 ("driver: ddr: Refine the ddr init driver on imx8m")
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Enable driver model support for FEC ethernet which allows us to remove
the iomux and board_eth_init function. Replace the toggling of the ethernet
phy reset with dt configuration.
Enable driver model support for PCI which allows us to remove the
eth1000_initialize() call. Additionally enable PCI_INIT_R to scan for
PCI devices on init such as the e1000 that is present on the GW552x.
Convert board_pci_fixup to use dm callback and remove pcidisable env
variable which is not supported for DM_PCI and thus leave PCI always
enabled during init.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Clock initialization functionality has ambitious debug messages, which are
printed out when failures are triggered during execution:
- Separate frequency table lookup functions have the the same output that
makes it impossible to understand which function failed and produced the
output
- PLL decoding routine has a generic debug statement printed, which does
not state the actual value failed to be found
Extend the output for both cases with prefixing table lookup functions
output with function name, and report the failed value in PLL decoding
routine.
Signed-off-by: Andrey Zhizhikin <andrey.zhizhikin@leica-geosystems.com>
Cc: Stefano Babic <sbabic@denx.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: "NXP i.MX U-Boot Team" <uboot-imx@nxp.com>
Cc: Peng Fan <peng.fan@nxp.com>
Cc: Simon Glass <sjg@chromium.org>
Cc: Ye Li <ye.li@nxp.com>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
A simple prototyping board with one microSD port, one Ethernet port,
2 USB ports, I2C, SPI, GPIO, and UART interfaces.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Board designed for quick prototyping and has one microSD port,
2 Ethernet ports, 2 USB ports, I2C, SPI, CAN, RS-485, GPIO,
UART interfaces, and 2 RGB LEDs.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Cc: Stefano Babic <sbabic@denx.de>
Uncompressed aarch64 kernel Image are rather large, increase the bootm
size limit to 64 MiB to cater for that.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Marcel Ziswiler <marcel.ziswiler@toradex.com>
Cc: Max Krummenacher <max.krummenacher@toradex.com>
Cc: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Reviewed-by: Oleksandr Suvorov <oleksandr.suvorov@toradex.com>
Usb needs IMXRT1050_CLK_USBOH3 clock to be enabled, so let's add it to
clock driver.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
We need those macros to instruct drivers on how to behave for SoC specific
quirks, so let's add it as done for other i.MX SoCs.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
At the moment a lot of u-boot,dm-spl properties are present in board .dts
file but this is not correct since u-boot,dm-spl property is u-boot
specific and must be listed into the separate imrt1020-evk-u-boot.dtsi
file. So let's move every u-boot,dm-spl property present in
imxrt1020-evk.dts to imxrt1020-evk-u-boot.dtsi file.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
At the moment a lot of u-boot,dm-spl properties are present in board .dts
file but this is not correct since u-boot,dm-spl property is u-boot
specific and must be listed into the separate imrt1050-evk-u-boot.dtsi
file. So let's move every u-boot,dm-spl property present in
imxrt1050-evk.dts to imxrt1050-evk-u-boot.dtsi file.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Lcdif needs both "pix" and "axi" clocks to be enabled so let's add them to
lcdif node.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Since we assume pll5 is the default lcdif clock source let's move
assigned-clocks(-parents) properties to .dtsi file.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Lcd peripheral needs 2 different gates to be enable to work, so let's
introduce the missing one(LCDIF_PIX) and rename the existing one
(LCDIF_APB).
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Some SoC needs "disp_axi" clock to be enabled, so let's try to retrieve it
and enabling. If it fails it gives only a debug(), but this clock as well
as "axi" clock is not mandatory.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
On some SoC mxsfb needs more than one clock gate(actual "per" clock). So
let's introduce "axi" clock that can be provided but it's not mandatory.
This is inspired from linux mxsfb driver. Also let's rename "per" clock to
"pix" clock for compatibility with already existing .dts lcdif nodes
implementation.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Now device_type = "memory" is mandatory to allow u-boot to read memory
node, so let's add it to memory node.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
Now device_type = "memory" is mandatory to allow u-boot to read memory
node, so let's add it to memory node.
Signed-off-by: Giulio Benetti <giulio.benetti@benettiengineering.com>
