If SW 8 pins 0 and 1 indicate that NAND should be enabled then
the pins pinmux must be reconfigured for NAND mode.
Therefore, enable NAND by reconfiguring the pinmux.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
By default VOUT3 occupies the pins required for NAND. Therefore, create
a seperate entry that can be use to reconfigure these pins to work for
NAND.
On the EVM SWITCH 8 pins 0 and 1 will be used to determine if NAND is
enabled or not. For NAND to be selected pin 0 should be on and pin 1
should be off. Any other combination will assume NAND shouldn't be
enabled.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Faiz Abbas <faiz_abbas@ti.com>
With the memory mapping giving us some more avialable RAM, this
updates the da850-evm-u-boot.dtsi to include the serial port, SPI
and Flash nodes along with some dependent nodes in the SPL dtb.
This also removes the platform data initialization code for the
serial port and SPI Flash.
Signed-off-by: Adam Ford <aford173@gmail.com>
In order to fully support SPL_OF_CONTROL, we need BSS to be a bit
larger. This patch relocates BSS to SDRAM instead of SRAM which
is similar to how ARMv7 boards (like OMAP2+) do it.
This means two new variables are required:
CONFIG_SPL_BSS_START_ADDR set to DAVINCI_DDR_EMIF_DATA_BASE
CONFIG_SPL_BSS_MAX_SIZE is set to 0x1080000 which is 1 byte
before the location where U-Boot will load.
Signed-off-by: Adam Ford <aford173@gmail.com>
When booting using an SPL on am335x, if we want to support booting with
the boot ROM loader via USB (which uses RNDIS, making bootp and tftp
calls) we need to enable gadget eth in the SPL to load the main U-Boot
image. To enable CONFIG_SPL_ETH_SUPPORT, we must enable
CONFIG_SPL_ENV_SUPPORT as the environment is used by the eth support, but
we don't actually need to have environment variables saved in the SPL
environment. We do however have environment variables saved in the main
U-Boot image and enable CONFIG_ENV_OFFSET_REDUND (we are storing in raw
NAND). In such instances, even with the build config enabling both
CONFIG_CMD_SAVEENV and CONFIG_CMD_NAND, these options aren't set when
building the SPL, but CONFIG_ENV_OFFSET_REDUND still is.
Don't check this configuration option for SPL builds to enable the above
configuration.
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Add configuration for the MT41K128M16JT125K memory modules as used on the
Bosch Guardian device.
Based on a patch by:
Govindaraji Sivanantham <Govindaraji.Sivanantham@in.bosch.com>
Signed-off-by: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
[checkpatch.pl cleanup by Martyn Welch]
Signed-off-by: Martyn Welch <martyn.welch@collabora.com>
AM57xx IDK EVMs can boot out of QSPI. Enable configs to support QSPI
boot. Also enable configs for updating QSPI boot images over DFU.
Tested on AM572x IDK EVM.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
This patch adds dt node for DP83867 phy used on K2G ICE board and
also enable netcp device nodes for the board.
EVM hardware spec recommends to add 0.25 nsec delay in the tx
direction and 2.25 nsec delay in the rx direction for internal
delay in the clock path to be on the safer side.
The board straps RX_DV/RX_CTRL pin of on board DP83867 phy in mode
1. Unfortunately, the phy data manual disallows this. Add
ti,dp83867-rxctrl-strap-quirk in the phy node to allow software to
enable workaround suggested for this incorrect strap setting. This
ensures proper operation of this PHY.
The dts bindings are kept in sync with that from 4.14.y linux
kernel. This required the pinmux device related bindings to be
commented out to allow for compilation.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enable ti phy dp83867 for k2g
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch removes the unused phy-mode property from the phy dt node. On
K2G, currently link-interface determines if phy is used or not and is
already set to use rgmii. So this is not needed. Besides phy-mode should
be added to slave interface configuration of the cpsw driver, not in the
phy node.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch adds a workaround to reset the phy one time during boot
using GPIO0 pin 10 to make sure, the Phy latches the configuration
from the input pins correctly.
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Enhance the netcp driver to support phys that can be configured
for internal delay (rgmii-id, rgmii-rxid, rgmii-txid)
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
This patch updates pinmux configuration for K2G GP EVM based on
data generated by the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
This add pinmux configuration for rgmii interface so that network
driver can be supported on K2G ICE boards. The pinmux configurations
for this are generated using the pinmux tool at
https://dev.ti.com/pinmux/app.html#/default
As this required some BUFFER_CLASS definitions, same is re-used
from the linux defnitions in include/dt-bindings/pinctrl/keystone.h
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Reviewed-by: Lokesh Vutla <lokeshvutla@ti.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>
Sync armada-385-db-88f6820-amc.dts with Linux. Retain the
u-boot,dm-pre-reloc and nand differences.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
This board was added to u-boot first but the Linux maintainers requested
a more descriptive name. Rename the file to match the Linux usage and
update the board defconfig.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Commit 93b283d49f ("ARM: CPU: arm926ejs: Consolidate cache routines to
common file") changed cache setup for Kirkwood such that icache_enable()
is now called from enable_caches() which is called from initr_caches()
which is in the list of functions in init_sequence_r[] prior to
arch_misc_init(). This means the call to icache_enable() in
arch_misc_init() is no longer required, so remove it.
Signed-off-by: Leigh Brown <leigh@solinno.co.uk>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The DB-XC3-24G4XG is a switch development board from Marvell. It can
either use and external CPU card such as the db-88f6820-amc or the
internal CPU that is integrated into the switch.
Add support for running U-Boot on the internal CPU and enable the USB,
SPI and NAND peripherals. For now this needs the bin_hdr from the
Marvell U-Boot for this board.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
One difference with the integrated CPUs is that they use a different
clock control block to the Armada devices. Update mvebu_get_nand_clock()
accordingly.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Marvell's switch chips with integrated CPUs (collectively referred to as
MSYS) share common ancestry with the Armada SoCs. Some of the IP blocks
(e.g. xor) are located at different addresses and DFX server exists as a
separate target on the MBUS (on Armada-38x it's just part of the core
complex registers).
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
We now have MEVBU boards without SPL support (e.g. db-xc3-24g4xg).
Because of this, a new compile time warning from Kconfig is show:
WARNING: unmet direct dependencies detected for SPL_OF_CONTROL
Depends on [n]: SUPPORT_OF_CONTROL [=y] && SPL [=n] && OF_CONTROL [=y]
Selected by [y]:
- ARMADA_32BIT [=y] && ARM [=y] && ARCH_MVEBU [=y]
WARNING: unmet direct dependencies detected for SPL_DM
Depends on [n]: DM [=y] && SPL [=n]
Selected by [y]:
- ARMADA_32BIT [=y] && ARM [=y] && ARCH_MVEBU [=y]
...
This patch fixes this issue and removes these warnings.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
This patch enables the PCIe port specific link capabilities configuration
for Armada XP. The weak function board_sat_r_get() was used to return
a common flag for PCIe Gen1 vs Gen2 capability for all PCIe ports. This
is now changed with this patch to return a bit per PCIe port (4 bits
in this case, bit 0 for PCIe port 0, etc).
The theadorable board uses this new feature to configure PCIe port 0
as Gen1 and all other PCIe ports as Gen2 capable. All other AXP boards
using this function are not changed in the configuration and still
configure all ports as PCIe Gen2.
This patch also removes the parameter "pex_mode" from
board_serdes_cfg_get() as this parameter was not used in any of the
implementations.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Add a command to control the watchdog devices. This is useful if the
watchdog is rather long running (eg. seconds) and it should be
controlled by scripts. It is also handy during debugging.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Switch from legacy IDE driver to sata_mv driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The kirkwood devices are compatible with this driver.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Fix the worng include and offset macros.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This fixes a compile error on kirkwood.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables CONFIG_BLK for the ds414 Armada XP based platform.
This removes this build warning:
===================== WARNING ======================
This board does not use CONFIG_DM_USB. Please update
the board to use CONFIG_DM_USB before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Please note that I don't have this board and can't test this change.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Phil Sutter <phil@nwl.cc>
Following commits abe66b1b5d ("Convert CONFIG_ENV_SPI_* to Kconfig")
and 14453fbfad ("Convert CONFIG_SF_DEFAULT_* to Kconfig") remove
dandling comment lines and empty #ifdef sections.
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Document build and install of U-Boot image on Clearfog with eMMC.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Update the kirkwood entry to match MAINTAINERS following commit
1579faf52b ("MAINTAINERS: Update u-boot-marvell entry").
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
With board_ahci_enable() implementation for Armada 38x in place we can
now enable 38x support in the ahci_mvebu driver.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This allows the ahci_mvebu driver to do A38x platform specific
configuration at initialization.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_USB and CONFIG_BLK.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_USB and CONFIG_BLK.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_USB and CONFIG_BLK.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_USB and CONFIG_BLK.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_USB and CONFIG_BLK.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Enable CONFIG_DM_USB and where possible CONFIG_BLK.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Tested-by: Leigh Brown <leigh@solinno.co.uk>
Signed-off-by: Stefan Roese <sr@denx.de>
Now that kirkwood is using the mvebu mbus this function is no longer
needed.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
The mvebu mbus code already had most of the support required for
kirkwood. The only difference is that unlike the other mvebu targets
kirkwood doesn't have a bridge control block so the code related to
managing that needs to be compiled out.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
KW_DEFADR_PCI_IO_REMAP has the same value as KW_DEFADR_PCI_IO and is
only used to set up a 1:1 mapping. Remove it and update the mapping to
use KW_DEFADR_PCI_IO.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
This will allow the kirkwood platforms to use more common code with the
other mvebu SoCs.
Signed-off-by: Chris Packham <judge.packham@gmail.com>
Reviewed-by: Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
When checking for boards that are enabling a SATA driver that isn't
converted to DM yet we need to be sure to not also trip over boards that
do set CONFIG_AHCI & CONFIG_BLK by itself, as that is not a bug.
This was detected when converting the Armada XP SATA driver sata_mv.c
to DM with AHCI & BLK support. This warning is still printed without
this patch applied here.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The check for the missing PEX switch can lead to an infinite loop, when
the PCIe device is not found. It is helpful to enable the user to break
out of this boot-loop, to enable booting to the prompt for test cases.
This patch adds a 3 second delay in the error case before rebooting.
The user can press Ctrl-C in this time to abort the boot-loop.
This patch also calls bootcount_inc() before rebooting in the error
case. This is needed to increment the bootcounter, since this function
is called earlier than the main bootcounter increment. Otherwise the
bootcounter will not be incremented in the error case at all.
Signed-off-by: Stefan Roese <sr@denx.de>
This patch enables CONFIG_BLK as this is now possible with the recent
DM conversion of the Armada XP SATA driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This patch enables CONFIG_BLK as this is now possible with the recent
DM conversion of the Armada XP SATA driver.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
This patch adds DM support to the Armada XP SATA driver. This is needed
to enable CONFIG_BLK on this platform. It adds the SATA controller as
AHCI device, which is strictly speaking not correct, as the controller
is not AHCI compatible. But the U-Boot AHCI uclass interface enables
the usage of this DM driver and the creation of the corresponding BLK
devices.
This conversion is done to get rid of the compile warning:
Reviewed-by: Chris Packham <judge.packham@gmail.com>
===================== WARNING ======================
This board does not use CONFIG_DM_SCSI. Please update
the storage controller to use CONFIG_DM_SCSI before the v2019.07 release.
Failure to update by the deadline may result in board removal.
See doc/driver-model/MIGRATION.txt for more info.
====================================================
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Simon Glass <sjg@chromium.org>
Cc: Tom Rini <trini@konsulko.com>
