Commit graph

66 commits

Author SHA1 Message Date
Pali Rohár
049704f808 board_f: Fix types for board_get_usable_ram_top()
Commit 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
changed type of ram_top member from ulong to phys_addr_t but did not
changed types in board_get_usable_ram_top() function which returns value
for ram_top.

So change ulong to phys_addr_t type also in board_get_usable_ram_top()
signature and implementations.

Fixes: 37dc958947 ("global_data.h: Change ram_top type to phys_addr_t")
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
2022-09-23 15:12:42 -04:00
Andre Przywara
e26ece267e sunxi: board: Fix UART PortF pinmux setup
When CONFIG_UART0_PORT_F is defined, we try to configure two PortF pins
(usually used for the SD card) as UART0. Some SoCs use the mux value of
3 for this, while others use 4.

The combination of Kconfig symbols we currently use was not quite right:
we mis-configure the A31, A64, H6 and H616.

Going through the list in the pinctrl driver, there are only a few older
SoCs that use a value of 4, so revert the #ifdef clause, and name those
explicitly, instead of the other way around.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
2022-05-24 01:45:47 +01:00
Andre Przywara
b9a2e18533 sunxi: eMMC: Improve automatic boot source detection
When the Allwinner BROM loads the SPL from an eMMC boot partition, it
sets the boot source byte to the same value as when booting from the
user data partition. This prevents us from determining the boot source
to load U-Boot proper from the proper partition for sure.

The generic SPL MMC code already looks at the enabled boot partition
number, to load U-Boot proper from the same partition, but this fails
if there is nothing bootable in this partition, as the BROM then
silently falls back to the user data partition, which the SPL misses.

To learn about the actual boot source anyway, we repeat the algorithm
the BROM used to select the boot partition in the first place:
- Test EXT_CSD[179] to check if an eMMC boot partition is enabled.
- Test EXT_CSD[177] to check for valid MMC interface settings.
- Check if BOOT_ACK is enabled.
- Check the beginning of the first sector for a valid eGON signature.
- Load the whole SPL.
- Recalculate the checksum to verify the SPL is valid.

If one of those steps fails, we bail out and continue loading from the
user data partition. Otherwise we load from the selected boot partition.

Since the boot source is needed twice in the boot process, we cache the
result of this test to avoid doing this costly test multiple times.

This allows the very same image file to be put onto an SD card, into the
eMMC user data partition or into the eMMC boot partition, and safely
loads the whole of U-Boot from there.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-05 00:08:40 +01:00
Angelo Dureghello
482c1ccd1c sunxi: H3: fix non working console on uart2
Fix non working console on uart2, that seems releated to both
Allwinner H2+ and H3.

Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
[Andre: remove H2+, rearrange pin setup order]
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Samuel Holland
44de13d945 sunxi: Support SPL in both eGON and TOC0 images
SPL uses the image header to detect the boot device and to find the
offset of the next U-Boot stage. Since this information is stored
differently in the eGON and TOC0 image headers, add code to find the
correct value based on the image type currently in use.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-04-04 23:24:17 +01:00
Andre Przywara
e943753dc2 sunxi: Fix old GMAC pinmux setup
Commit 5bc4cd05d7 ("sunxi: move non-essential code out of s_init()")
moved the call to eth_init_board() from s_init() into board_init_f().
This means it's now only called from the SPL, which makes sense for
most of the other moved low-level functions. However the GMAC pinmux and
clock setup in eth_init_board() was not happy about that, so it broke
the sun7i GMAC.

Since Ethernet is of no use in the SPL anyway, just move the call into
board_init(), which is only run in U-Boot proper.

This fixes Ethernet operation for the A20 SoCs, which broke in
v2022.04-rc1, with the above mentioned commit.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@gmail.com>
Tested-by: Petr Štetiar <ynezz@true.cz> [a20-olinuxino-lime2]
2022-03-26 00:16:06 +00:00
Jesse Taube
a08b04b5c7 mach-sunxi: Add boot device detection for SUNIV/F1C100s
In contrast to other Allwinner SoCs the F1C100s BROM does not store a
boot source indicator in the eGON header in SRAM. This leaves the SPL
guessing where we were exactly booted from, and for instance trying
the SD card first, even though we booted from SPI flash.

By inspecting the BROM code and by experimentation, Samuel found that the
top of the BROM stack contains unique pointers for each of the boot
sources, which we can use as a boot source indicator.

This patch removes the existing board_boot_order bodge and replace it
with a proper boot source indication function.

The only caveat is that this only works in the SPL, as the SPL header
gets overwritten with the exception vectors, once U-Boot proper takes
over. Always return MMC0 as the boot source, when called from U-Boot
proper, as a placeholder for now, until we find another way.

Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Suggested-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-03-03 01:23:58 +00:00
Icenowy Zheng
cfe673cda7 mach-sunxi: Add support for SUNIV architecture
Add support for the suniv architecture, which is newer ARM9 SoCs by
Allwinner. The design of it seems to be a mixture of sun3i, sun4i and
sun6i.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04 00:09:57 +00:00
Andre Przywara
b8cd7f439a armv8: remove no longer needed lowlevel_init.S
When we added Allwinner SoC support to ARMv8, we needed to pull in an
implementation of lowlevel_init() calling the C function s_init(), as
sunxi required it as this time.

The last few patches got rid of this bogus requirement, and as sunxi was
still the only user, we can now remove this lowlevel_init.S from ARMv8
altogether.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2022-02-04 00:09:57 +00:00
Andre Przywara
534b82a1f2 sunxi: move early "SRAM setup" into separate file
Currently we do some magic "SRAM setup" MMIO writes in s_init(), copied
from the original BSP U-Boot. The comment speaks of this being required
before DRAM access gets enabled, but there is no indication that this
would actually be required that early.

Move this out of s_init(), into board_init_f(). Since this actually only
affects a very few older SoCs, the actual code goes into the cpu/armv7
directory, to move it out of the way for all other SoCs.

This also uses the opportunity to convert some #ifdefs over to the fancy
IS_ENABLED() macros used in actual C code.

We keep the s_init() stub around for now, since armv8's lowlevel_init
still relies on it.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
2022-02-04 00:09:57 +00:00
Andre Przywara
2564fce7ee sunxi: move Cortex SMPEN setting into start.S
According to their TRMs, Cortex ARMv7 CPUs with SMP support require the
ACTLR.SMPEN bit to be set as early as possible, before any cache or TLB
maintenance operations are done. As we do those things still in start.S,
we need to move the SMPEN bit setting there, too.

This introduces a new ARMv7 wide symbol and code to set bit 6 in ACTLR
very early in start.S, and moves sunxi boards over to use that instead
of the custom code we had in our board.c file (where it was called
technically too late).

In practice we got away with this so far, because at this point all the
other cores were still in reset, so any broadcasting would have been
ignored anyway. But it is architecturally cleaner to do it early, and
we move a core specific piece of code out of board.c.

This also gets rid of the ARM_CORTEX_CPU_IS_UP kludge I introduced a few
years back, and moves the respective logic into the new Kconfig entry.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04 00:09:36 +00:00
Andre Przywara
5bc4cd05d7 sunxi: move non-essential code out of s_init()
So far all Allwinner based boards were doing some not-so-lowlevel-setup
in lowlevel's s_init() routine.
This includes the initial clock, timer and pinmux setup, among other
things. This is clearly out of the "absolute bare minimum to get started"
scope that lowlevel_init.S suggests for this function.

Since we have an SPL, which is called right after s_init(), move those
calls to our board_init_f() function. As we overwrite this only for
the SPL, this has the added benefit of not doing this setup *again*
shortly afterwards, when running U-Boot proper.

This makes gpio_init() to be called from the SPL only, so pull this code
into a CONFIG_SPL_BUILD protected part to avoid build warnings.

Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Simon Glass <sjg@chromium.org>
Tested-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2022-02-04 00:09:03 +00:00
Samuel Holland
6e19dc84c1 sunxi: Avoid duplicate reset_cpu with SYSRESET enabled
The sysreset uclass unconditionally provides a definition of the
reset_cpu() function. So does the sunxi board code. Fix the build with
SYSRESET enabled by omitting the function from the board code in that
case. The code still needs to be kept around for use in SPL.

Reviewed-by: Heinrich Schuchardt <heinrich.schuchardt@canonical.com>
Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Stefan Roese <sr@denx.de>
2021-11-04 08:57:19 +01:00
Samuel Holland
ea261fdeb2 sunxi: Only initialize legacy I2C when enabled
CONFIG_SPL_I2C is the wrong symbol to use here. It is the top-level
Kconfig symbol (not specific to either legacy or DM I2C), whereas the
i2c_init() function is specific to legacy I2C. This change fixes a
build failure when enabling SPL_I2C but not SPL_SYS_I2C_LEGACY.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-by: Andre Przywara <andre.przywara@arm.com>
2021-10-12 09:49:09 +01:00
Samuel Holland
425084610e sunxi: Clean up inclusions of asm/arch/gpio.h
As part of migrating to DM_GPIO and DM_PINCTRL, eventually we will
remove the asm/arch/gpio.h header. In preparation, clean up the various
files that include it.

Some files did not contain any GPIO code at all, so this header was
completely unused.

A few files contained only legacy platform-specific GPIO code for
setting up pin muxes. They were left unchanged, as that code will be
completely removed by the DM_PINCTRL migration.

The remaining files contain some combination of DM_GPIO and legacy GPIO
code. For those, switch to including asm/gpio.h (if it wasn't included
already). Right now, this header provides both sets of functions,
because ARCH_SUNXI selects GPIO_EXTRA_HEADER. This will still be the
right header to include once the DM_GPIO migration is complete and
GPIO_EXTRA_HEADER is no longer needed.

Signed-off-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-10-11 10:46:44 +01:00
Simon Glass
975e7cf301 i2c: Rename SPL/TPL_I2C_SUPPORT to I2C
Rename these options so that CONFIG_IS_ENABLED can be used with them.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Heiko Schocher <hs@denx.de>
2021-07-28 14:29:37 -04:00
Andre Przywara
b8747854de sunxi: H616: Enable full 4GB of DRAM
The H616 is our first supported Allwinner SoC which goes beyond the 4GB
address space "barrier", by having more than 32 address bits.

Lift the preliminary 3GB DRAM limit for the H616, and update the page
table setup on the way, to actually map that last GB as well.

As not all devices are actually capable of dealing with more than 32
bits (the DMA in the EMAC for instance), we also limit U-Boot's own
DRAM usage to 4GB on the way.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-07-10 01:22:09 +01:00
Marek Behún
236f2ec432 treewide: Convert macro and uses of __section(foo) to __section("foo")
This commit does the same thing as Linux commit 33def8498fdd.

Use a more generic form for __section that requires quotes to avoid
complications with clang and gcc differences.

Remove the quote operator # from compiler_attributes.h __section macro.

Convert all unquoted __section(foo) uses to quoted __section("foo").
Also convert __attribute__((section("foo"))) uses to __section("foo")
even if the __attribute__ has multiple list entry forms.

Signed-off-by: Marek Behún <marek.behun@nic.cz>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-05-24 14:21:30 -04:00
Harald Seiler
35b65dd8ef reset: Remove addr parameter from reset_cpu()
Historically, the reset_cpu() function had an `addr` parameter which was
meant to pass in an address of the reset vector location, where the CPU
should reset to.  This feature is no longer used anywhere in U-Boot as
all reset_cpu() implementations now ignore the passed value.  Generic
code has been added which always calls reset_cpu() with `0` which means
this feature can no longer be used easily anyway.

Over time, many implementations seem to have "misunderstood" the
existence of this parameter as a way to customize/parameterize the reset
(e.g.  COLD vs WARM resets).  As this is not properly supported, the
code will almost always not do what it is intended to (because all
call-sites just call reset_cpu() with 0).

To avoid confusion and to clean up the codebase from unused left-overs
of the past, remove the `addr` parameter entirely.  Code which intends
to support different kinds of resets should be rewritten as a sysreset
driver instead.

This transformation was done with the following coccinelle patch:

    @@
    expression argvalue;
    @@
    - reset_cpu(argvalue)
    + reset_cpu()

    @@
    identifier argname;
    type argtype;
    @@
    - reset_cpu(argtype argname)
    + reset_cpu(void)
    { ... }

Signed-off-by: Harald Seiler <hws@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
2021-03-02 14:03:02 -05:00
Igor Opaniuk
2147a16983 dm: i2c: use CONFIG_IS_ENABLED macro for DM_I2C/DM_I2C_GPIO
Use CONFIG_IS_ENABLED() macro, which provides more convenient
way to check $(SPL)DM_I2C/$(SPL)DM_I2C_GPIO configs
for both SPL and U-Boot proper.

CONFIG_IS_ENABLED(DM_I2C) expands to:
- 1 if CONFIG_SPL_BUILD is undefined and CONFIG_DM_I2C is set to 'y',
- 1 if CONFIG_SPL_BUILD is defined and CONFIG_SPL_DM_I2C is set to 'y',
- 0 otherwise.

All occurences were replaced automatically using these bash cmds:
$ find . -type f -exec sed -i
     's/ifndef CONFIG_DM_I2C/if !CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/ifdef CONFIG_DM_I2C/if CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/defined(CONFIG_DM_I2C)/CONFIG_IS_ENABLED(DM_I2C)/g' {} +
$ find . -type f -exec sed -i
    's/ifndef CONFIG_DM_I2C_GPIO/if !CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
    's/ifdef CONFIG_DM_I2C_GPIO/if CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +
$ find . -type f -exec sed -i
    's/defined(CONFIG_DM_I2C_GPIO)/CONFIG_IS_ENABLED(DM_I2C_GPIO)/g' {} +

Reviewed-by: Heiko Schocher <hs@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Igor Opaniuk <igor.opaniuk@foundries.io>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
2021-02-21 06:08:00 +01:00
Tobias Schramm
7f4e294b57 sunxi: support boot console on uart1 for sun8i
The A23, A33, H3, H5, A83T, V3 and Sochip S3 sun8i SoCs can mux uart1 on
GPIOs PG6 and PG7. This patch adds support for using uart1 on those pins
as boot console.

Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-02-19 23:28:50 +00:00
Jernej Skrabec
c13d98b77e sunxi: add support for H616 uart0
This port is used for debug terminal on all known H616 boards.

Reviewed-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:01 +00:00
Andre Przywara
c0b417b2f1 sunxi: support loading with SPL > 32KB
H616 supports and needs bigger SPL than 32 KiB, mostly due to big DRAM
driver and need for PMIC configuration, which pulls several drivers which
are not needed otherwise.

spl_mmc_get_uboot_raw_sector() will now compare pre-configured size with
that, reported in SPL header. If size in header is bigger, it will use
that value instead.

In the process of function rework, also add missing function argument.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
2021-01-25 21:52:00 +00:00
Jernej Skrabec
44726096cf sunxi: Introduce common symbol for H6 like SoCs
It turns out that there are at least 2 other SoCs which have basically
the same memory map, similar clocks and other features as H6. It's very
likely that we'll see more such SoCs in the future. In order to ease
porting to new SoCs and lower ifdef clutter, introduce common symbol for
them.

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Samuel Holland <samuel@sholland.org>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
2021-01-25 21:52:00 +00:00
Simon Glass
f7ae49fc4f common: Drop log.h from common header
Move this header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 21:19:18 -04:00
Simon Glass
691d719db7 common: Drop init.h from common header
Move this uncommon header out of the common header.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:33 -04:00
Simon Glass
90526e9fba common: Drop net.h from common header
Move this header out of the common header. Network support is used in
quite a few places but it still does not warrant blanket inclusion.

Note that this net.h header itself has quite a lot in it. It could be
split into the driver-mode support, functions, structures, checksumming,
etc.

Signed-off-by: Simon Glass <sjg@chromium.org>
2020-05-18 17:33:31 -04:00
Andre Przywara
7c841d844f sunxi: Automate loading from 128KB MMC offset
Since commit 067e0b9684 ("sunxi: Allow booting from 128KB SD/eMMC offset")
we support having the SPL loaded from either the traditional 8KB SD
card/eMMC offset, or from the alternative location at 128KB. However the
sector to find the U-Boot image was still hard-coded at compile time,
and had to be adjusted for one of the two choices.

Since we can actually override the function to return the sector offset,
we can just check the boot source byte there to select the proper offset
based on from where the SPL was loaded.

This allows the very same binary image to be loaded from either 128KB or
8KB, with the U-Boot proper image always being located just behind the SPL.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-26 19:10:16 +05:30
Andre Przywara
ee98d76893 sunxi: SPL: Factor out sunxi_get_boot_source()
The Boot ROM write some boot source ID (SD card, eMMC, SPI, ...) into
a certain location in SRAM, so the SPL can easily determine where to
load U-Boot proper from.
Factor out reading this value, as it will come in handy again shortly.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2020-01-26 19:09:34 +05:30
Simon Glass
9edefc2776 common: Move some cache and MMU functions out of common.h
These functions belong in cpu_func.h. Another option would be cache.h
but that code uses driver model and we have not moved these cache
functions to use driver model. Since they are CPU-related it seems
reasonable to put them here.

Move them over.

Signed-off-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
2019-12-02 18:23:55 -05:00
Icenowy Zheng
5f19c93021 sunxi: set PIO voltage to hardware-detected value on startup on H6
The Allwinner H6 SoC has a register to set the PIO banks' voltage. When
it mismatches the real voltage supplied to the VCC to the PIO supply,
the PIO will work improperly.

The PIO controller also has a register that contains the status of each
VCC rail of the PIO supplies, and it has the same definition with the
configuration register. so we can just copy the content of this register
to the configuration register at startup, to ensure the configuration is
correct at startup stage.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
[jagan: s/__maybe__unused/__maybe_unused]
Signed-off-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
2019-10-25 14:40:34 +05:30
Tom Rini
79764b5081 Merge branch 'master' of git://git.denx.de/u-boot-sunxi
- H6 WDT reset fix (Clément)
- H6 SPL_TEXT_BASE fixes (Clément, Jonas)
- NPI-M1+ emac enablment (Emmanuel)
2019-05-20 13:53:51 -04:00
Clément Péron
26f8e0d7f2 arm: sunxi: h6: fix reset using r_wdog
Some H6 boards have a watchdog which didn't make the SoC
reboot properly.

Reason is still unknown but several people have test it.
Chen-Yu Tsai :
Pine H64 = H6 V200-AWIN H6448BA 7782 => OK
OrangePi Lite 2 = H6 V200-AWIN H8068BA 61C2 => KO

Martin Ayotte :
Pine H64 = H8069BA 6892 => OK
OrangePi 3 = HA047BA 69W2 => KO
OrangePi One Plus = H7310BA 6842 => KO
OrangePi Lite2 = H6448BA 6662 => KO

Clément Péron:
Beelink GS1 = H6 V200-AWIN H7309BA 6842 => KO

After the series of result, Icenowy try to reach Allwinner about this
issue but they seems not interested to investigate it.

As we don't have the ARIS coproc to do power management and watchdogis
the only solution to reset the board.

So, Change from watchdog to R_watchdog to allow a reboot on all H6
boards.

Signed-off-by: Clément Péron <peron.clem@gmail.com>
Reviewed-by: Jagan Teki <jagan@amarulasolutions.com>
2019-05-20 22:24:47 +05:30
Trevor Woerner
1001502545 CONFIG_SPL_SYS_[DI]CACHE_OFF: add
While converting CONFIG_SYS_[DI]CACHE_OFF to Kconfig, there are instances
where these configuration items are conditional on SPL. This commit adds SPL
variants of these configuration items, uses CONFIG_IS_ENABLED(), and updates
the configurations as required.

Acked-by: Alexey Brodkin <abrodkin@synopsys.com>
Signed-off-by: Trevor Woerner <trevor@toganlabs.com>
[trini: Make the default depend on the setting for full U-Boot, update
more zynq hardware]
Signed-off-by: Tom Rini <trini@konsulko.com>
2019-05-18 08:15:35 -04:00
Andre Przywara
067e0b9684 sunxi: Allow booting from 128KB SD/eMMC offset
On modern Allwinner SoCs (tested: H2+, A64, H5, H6) the BootROM can
actually load the SPL also from sector 256 (128KB) of an SD card or eMMC
chip. For more details, see [1].
In this case the boot source indicator (written at offset 0x28 of SRAM A1)
has bit 4 set, so it's 0x10 for SD card and 0x12 for eMMC.

Add those new values to the existing boot source check to allow booting
the SPL from those "high" disk offsets as well. For this to work, the
value of CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR needs to be adjusted,
for instance to 0x140 (right after the high SPL). Doing this dynamically
sounds desirable, but looks nasty to implement.

[1] https://groups.google.com/forum/#!topic/linux-sunxi/MaiijyaAFjk

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
2019-04-10 15:34:32 +05:30
Icenowy Zheng
7009134c99 sunxi: map DRAM part with 3G size
All Allwinner 64-bit SoCs now are known to be able to access 3GiB of
external DRAM, however the size of DRAM part in the MMU translation
table is still 2GiB.

Change the size of DRAM part in MMU table to 3GiB.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2018-10-29 20:41:15 +05:30
Icenowy Zheng
7f51a4020e sunxi: add UART0 setup for H6
The UART0 on H6 is available at PH bank (and PF bank, but the PF one is
muxed with SD card).

Add pinmux configuration.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Icenowy Zheng
10196c9627 sunxi: use sun6i-style watchdog for H6
The H6 SoC has a sun6i-style watchdog in its timer part.

Enable the usage of it.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com>
2018-07-31 11:38:13 +05:30
Chris Packham
9508ecfbcb ARM: sunxi: remove empty #ifdef/endif block
Whatever code this was guarding has been removed so remove the guards
too.

Signed-off-by: Chris Packham <judge.packham@gmail.com>
2018-06-18 14:02:03 -04:00
Tom Rini
83d290c56f SPDX: Convert all of our single license tags to Linux Kernel style
When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from.  So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry.  Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents.  There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-05-07 09:34:12 -04:00
Tom Rini
d024236e5a Remove unnecessary instances of DECLARE_GLOBAL_DATA_PTR
We have a large number of places where while we historically referenced
gd in the code we no longer do, as well as cases where the code added
that line "just in case" during development and never dropped it.

Signed-off-by: Tom Rini <trini@konsulko.com>
2018-04-27 14:54:48 -04:00
Lukasz Majewski
d695d66278 spl: eMMC/SD: Provide one __weak spl_boot_mode() function
The goal of this patch is to clean up the code related to choosing SPL
MMC boot mode.

The spl_boot_mode() now is called only in spl_mmc_load_image() function,
which is only compiled in if CONFIG_SPL_MMC_SUPPORT is enabled.

To achieve the goal, all per mach/arch implementations eligible for
unification has been replaced with one __weak implementation.

Signed-off-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Stefano Babic <sbabic@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com> (For ZynqMP)
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
2018-02-07 22:06:18 -05:00
Maxime Ripard
8829076a5b arm: sunxi: Move spl_boot_device in a separate function
U-Boot itself might need to identify the boot device, for example to be
able to tell where to load the kernel from when several options are
possible.

Move the logic of spl_boot_device to a function that is compiled both for
the SPL and the main binary.

Tested-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-10-03 19:12:06 +02:00
Jernej Skrabec
a8f01ccff2 sunxi: i2c: Add support for DM I2C
This commit adds support for DM I2C on sunxi platform. It can coexist
with old style sunxi I2C driver, because it is still used in SPL and
by some SoCs.

Because sunxi platform doesn't yet support DM clk, reset and pinctrl
driver, workaround is needed to enable clocks and set resets and
pinctrls. This is done by calling i2c_init_board() in board_init().
This means that CONFIG_I2Cx_ENABLE options needs to be correctly set
in order to use needed I2C controller.

Commit is based on the previous patch made by Philipp Tomsich

Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-28 09:19:03 +02:00
Icenowy Zheng
c199489f17 sunxi: add basic V3s support
Basic U-Boot support is now present for V3s.

Some memory addresses are changed specially for V3s, as the original
address map cannot fit into a so small DRAM.

As the DRAM controller code needs a big refactor, the SPL support is
disabled in this version.

Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-21 09:23:17 +02:00
Chen-Yu Tsai
6c7ae2bfc9 sunxi: Fix watchdog reset function for R40
The watchdog found on the R40 SoC is the older variant found on the A20.
Add the proper "#if defines" to make it work.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:00 +02:00
Chen-Yu Tsai
379febac5a sunxi: Add initial support for R40
The R40 is the successor to the A20. It is a hybrid of the A20, A33
and the H3.

The R40's PIO controller is compatible with the A20,
Reuse the A20 UART and I2C muxing code by adding the R40's macro.

The display pipeline is the newer DE 2.0 variant.
Block enabling video on R40 for now.

Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-20 13:30:00 +02:00
Andre Przywara
7b82a229e5 sunxi: prepare for sharing MACH_SUN8I_H3 config symbol
The Allwinner H5 is very close to the H3 SoC, but has ARMv8 cores.
To allow sharing the clocks, GPIO and driver code easily, create an
architecture agnostic MACH_SUNXI_H3_H5 Kconfig symbol.
Rename the existing symbol to MACH_SUNXI_H3_H5 where code is shared and
let it be selected by a new shared Kconfig option.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
ce6912e128 sunxi: provide ARMv8 mem_map for every ARM64 board
Every armv8 board needs the memory map, so change the #ifdef to
ARM64 to avoid enumerating every single board or SoC.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
2017-04-05 15:03:17 +05:30
Andre Przywara
85db5831ad sunxi: simplify ACTLR.SMP bit set #ifdef
Instead of enumerating all SoC families that need that bit set, let's
just express this more clearly: The SMP bits needs to be set on
SMP capable ARMv7 CPUs. It's much easier in Kconfig to express it the
other way round, so we use ! CPU_IS_UP and ! ARM64.

Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
2017-04-05 15:03:17 +05:30