The VIM3 on-board MCU can mux the PCIe/USB3.0 shared differential
lines using a FUSB340TMX USB 3.1 SuperSpeed Data Switch between
an USB3.0 Type A connector and a M.2 Key M slot.
The PHY driving these differential lines is shared between
the USB3.0 controller and the PCIe Controller, thus only
a single controller can use it.
This adds this dynamic switching right before booting Linux
and the configuration steps in the boards documentation.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
[narmstrong: fixed warning by replacing min() by min_t()]
Use the newly added VIM3 board support instead of the generic W400.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The VIM3 will need a specific code to enable PCIe if enabled in the MCU,
thus add a specific board support for VIM3 & VIM3L.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This imports the G12A & SM1 SoC and boards DT changes from the Linux
commit 9123e3a74ec7 ("Linux 5.9-rc1").
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Kevin Hilman <khilman@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the correcly architectured USB Glue node for Meson AXG and the
S400 board in -u-boot.dtsi until support in upstream Linux then
backported.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Add the board_usb_init()/cleanup() for USB gadget for AXG based
on the code for the G12A architecture.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The registers which are managed by the meson-gxl-usb3 PHY driver are
actually "USB control" registers (which are "glue" registers which
manage OTG detection and routing of the OTG capable port between the
DWC2 peripheral-only controller and the DWC3 host-only controller).
Drop the meson-gxl-usb3 PHY driver now that the dwc3-meson-gxl-usb
driver supports the USB control registers on GXL and GXM SoCs (these
were previously managed by the meson-gxl-usb3 PHY driver).
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
The USB support was initialy done with a set of PHYs and dwc3-of-simple
because the architecture of the USB complex was not understood correctly
at the time (and proper documentation was missing...).
But with the G12A family, the USB complex was correctly understood and
implemented correctly.
This adds a proper driver for the glue, based on the G12A one, but with
enough changes to require a different driver in U-Boot.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
This imports the AXG, GXL & GXM SoC and boards DT changes from the Linux
commit b3a9e3b9622a ("Linux 5.8-rc1").
This change also removes GXL & GXM u-boot.dtsi hacks for USB gadget.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
According to doc/README.distro fdt_addr must not be set when DTB is not
available from hardware. So remove this entry.
Use address 32MB above the start of DRAM for kernel_addr_r. This way
we likely can avoid the self-relocation of the compressed kernel image
before it decompresses to offset 0x8000 from start of DRAM.
Use address 128MB above the start of DRAM for fdt_addr_r, since this is
the maximum location for the end of the kernel. So we avoid overwriting
the DTB.
Use 512k above that for ramdisk_addr_r. This should be enough for the
DTB, rest of DRAM can be used for initrd.
Place boot script / extlinux.conf at offset 0 / 1MB from start of DRAM.
This space is available for processing in U-Boot.
Signed-off-by: Soeren Moch <smoch@web.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
The u-boot,dm-spl DT props are missing on AV96, hence the pinmux and
flash0 nodes are not included in the reduced SPL DT. This prevents
SPI NOR boot from working at all. Fix this by filling them in.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Patrick Delaunay <patrick.delaunay@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrice Chotard <patrice.chotard@st.com>
Reviewed-by: Patrick Delaunay <patrick.delaunay@st.com>
The patches changing the compatible strings to the ones used by Linux have
not been merged yet, so fix the checks to use the current in-tree ones.
Reported-by: Pali Rohár <pali@kernel.org>
Signed-off-by: Andre Heider <a.heider@gmail.com>
Reviewed-by: Pali Rohár <pali@kernel.org>
Some Espressobin boards got assigned more than one MAC address. Update
instructions how to correctly store and preserve all MAC addresses.
Signed-off-by: Pali Rohár <pali@kernel.org>
Reviewed-by: Andre Heider <a.heider@gmail.com>
commit 7c8f821e5d ("i2c: rcar_i2c: Set the slave address from
rcar_i2c_xfer") blindly called rcar_i2c_set_addr() with read argument
always set to 1 during xfer which introduced read/write errors, whereas
earlier rcar_i2c_read_common() called rcar_i2c_set_addr() with read set to
1 and rcar_i2c_write_common() called rcar_i2c_set_addr() with read set 0.
Fixes: 7c8f821e5d ("i2c: rcar_i2c: Set the slave address from rcar_i2c_xfer")
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Move call to optee_copy_fdt_nodes() introduced by commit 6ccb05eae0
before generic changes in kernel FDT so that platform specific changes
are not overridden by the changes made by this function.
Fixes: 6ccb05eae0 ("image: fdt: copy possible optee nodes to a loaded devicetree")
Signed-off-by: Etienne Carriere <etienne.carriere@linaro.org>
Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
We should check if the incoming parameter file_mapping is not NULL instead
of checking after adding an offset.
Reported-by: Coverity CID 307210
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Acked-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Fix a typo
%s/interract/interact/
Use Samsung's capitalization of their trademarks
%s/onenand/OneNAND/
%s/Hyperflash/HyperFlash/
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Stefan Roese <sr@denx.de>
[trini: Add other Hyperflash cases as noted by Stefan]
Signed-off-by: Tom Rini <trini@konsulko.com>
The 44758771ee commit removes CONFIG_PREBOOT but actually sets the USE_PREBOOT
Kconfig option which isn't CONFIG_PREBOOT and is also a bool option which means
we regress because 'usb start' isn't run when expected, it should also be run
for devices that have USB storage because keyboards aren't the only thing we
might need the USB bus for.
Fixes: 44758771ee ("arm: move CONFIG_PREBOOT="usb start" to KConfig")
Signed-off-by: Peter Robinson <pbrobinson@gmail.com>
Cc: Jonas Smedegaard <dr@jones.dk>
Cc: Neil Armstrong <narmstrong@baylibre.com>
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
-----BEGIN PGP SIGNATURE-----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=W9Wz
-----END PGP SIGNATURE-----
Merge tag 'efi-2020-10-rc6' of https://gitlab.denx.de/u-boot/custodians/u-boot-efi
Pull request for UEFI sub-system for efi-2020-10-rc6
The following UEFI related issues are fixed:
* restore the global data pointer in the RISC-V trap handler
* install EFI_RNG_PROTOCOL only if we have a random number generator
* display human readable string for EFI_RNG_PROTOCOL in efidebug command
The gp register is used to store U-Boot's global data pointer. We should
not assume that an UEFI application leaves the gp register unchanged as
the UEFI specifications does not define who is the owner of the gp and tp
registers.
So the following sequence should be followed in the trap handler:
* save the caller's gp register
* restore the global data pointer
* serve interrupts or print crash dump and reset
* restore the caller's gp register
Cc: Abner Chang <abner.chang@hpe.com>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Rick Chen <rick@andestech.com>
This fixes HWRNG support on Amlogic GXL, GXM, G12A, G12B & SM1
based boards dues to the lack of the core clock in the device tree.
It was reported breaking EFI boot in the Linux EFI stub, because the
EFI_RNG_PROTOCOL didn't check for the RNG device presence before
installing itself.
The Linux amlogic,meson-rng.yaml doesn't mandate the core clock,
this the clock should be ignores if not present.
Nevertheless, the clock should be present and this should be fixed
on the Linux meson-gxl.dtsi & meson-g12-common.dtsi then synced
with U-Boot.
The change has been tested on a Khadas VIM3, which uses the common
meson-g12-common.dtsi like the Odroid-C4 & Odroid-N2 in Scott's
report, along with the RNG cmd.
Cc: Heinrich Schuchardt <xypron.glpk@gmx.de>
Reported-by: Scott K Logan <logans@cottsay.net>
Fixes: bc40eb278b ("drivers/rng: add Amlogic hardware RNG driver")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Scott K Logan <logans@cottsay.net>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Having an EFI_RNG_PROTOCOL without a backing RNG device leads to failure
to boot Linux 5.8.
Only install the EFI_RNG_PROTOCOL if we have a RNG device.
Reported-by: Scott K Logan <logans@cottsay.net>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Add the Random Number Generator (RNG) protocol to the GUIDs that the
'efidebug dh' protocol can replace by a text.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Renesas Ebisu board is based on R-Car E3 SoC which has dual CA53 and
a CR7.
This patch drops check for cputype from reset_cpu() and also drops the
corresponding CA57 macros. While at it also dropped RST_RSTOUTCR macro
which is unused.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
LX2160A rev2 uses different PCIe controller, so EP mode DT
nodes also need to be fixed up.
Signed-off-by: Hou Zhiqiang <Zhiqiang.Hou@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
CONFIG_DM_SPI_FLASH is only supported now with passing of driver
conversion deadline from non-DM to DM model. Hence, it's safe to remove
non-DM code check from pfe_spi_flash_init.
Also use CONFIG_ENV_SPI_MODE and CONFIG_ENV_SPI_MAX_HZ instead of
reading reading values from DT.
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Fix Coverity issue: RESOURCE_LEAK.
leaked_storage: Variable addr going out of scope leaks the storage it
points to.
Fixes: e0152dbed6 ("net: pfe_eth: Use spi_flash_read API to access
flash memory")
Signed-off-by: Kuldeep Singh <kuldeep.singh@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
All the 10G ports that were working in XFI mode were described as
using XGMII (as PHY_INTERFACE_MODE_XFI was not added at the time).
Add the minimal changes required for the FMan code to support XFI.
Signed-off-by: Madalin Bucur <madalin.bucur@oss.nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
PFE DDR addresses are now stored on to a stack varaiable rather
dynamic allocation.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
correction in delay implementation before we exit out of tx timeout.
Signed-off-by: Chaitanya Sakinam <chaitanya.sakinam@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
The next DPMAC was always verified if it is enabled. In case of
DPMAC@6, the DPMAC@7 is verified. As DPMAC@7 is disabled, DPMAC@6 will
be considered disabled and not detected by uboot.
Signed-off-by: Grigore Popescu <grigore.popescu@nxp.com>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
Make sure that SW_RST_REQ and RST_REQ_MSK are cleared
before triggering hardware reset request.
Signed-off-by: Thirupathaiah Annapureddy <thiruan@linux.microsoft.com>
Signed-off-by: Meenakshi Aggarwal <meenakshi.aggarwal@nxp.com>
Reviewed-by: Priyanka Jain <priyanka.jain@nxp.com>
