Add basic DT support for K2G ICE evm. Only minimal peripherals are
supported to allow console output and MMC boot.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Disable netcp by default like all other peripherals in the dtsi file.
Enable the peripheral explicitly in the board specific dts file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Upstream Linux has the unit address being added to the various 66AK2Gx
boards dts. Therefore, update the dts to mimic this change.
Also remove memory node from the base K2G dtsi file.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Adding the unit address to the memory node was causing the below error:
Warning (reg_format): "reg" property in /memory has invalid length
(8 bytes) (#address-cells == 2, #size-cells == 2)
Further debugging showed that this was due to the memory node added by
default to skeleton.dtsi which was being included in keystone-k2g.dtsi.
Adding a missing node was all that was needed to remove this deprecated
dtsi file from the SoC dtsi. With skeleton.dtsi removed the dtc compiler
no longer complained about including the unit address for the memory node.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Different K2G evms may need to program the various
KS2_DDRPHY_DATX8_X_OFFSET registers in different ways. Therefore, use
the mask and val registers for each KS2_DDRPHY_DATAX_X_OFFSET to
properly program the register.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
K2G GP doesn't require the MR2 register to be programed since the
default is good enough. However, newer K2G boards do need to change
this register value. Therefore, instead of not writing this register if
ran on a K2G board just program the value to be written to match the
default/reset value.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Future boards will need to configure DDR3 registers in a slightly
different manner. Support this by defining additional variables and
defines that will be utilized later.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
u-boot.bin is a copy of:
u-boot-fit-dtb.bin if CONFIG_FIT_EMBED is enabled,
u-boot-dtb.bin if CONFIG_OF_SEPARATE is enabled,
u-boot-nodtb.bin if DT is not enabled.
So, use u-boot.bin to to generate keystone images instead of
u-boot-dtb.bin
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With U-boot runtime board detect for DTB selection a "default" dtb needs
to be created. This will be used temporarily until the "proper" dtb is
selected.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Introduce K2G evm specific dtsi file for U-boot specific configurations.
This will help seperate U-boot only configurations thus making it easier to
keep device tree files synced between U-boot and Linux.
For now only add nodes to allow i2c drivers to be probed early during
the boot process.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
With Davinci I2C switching to device model, K2E requires U-boot specific
device tree entries. This is only required for I2C 1 which is needed
extremely early during the boot process.
Fixes: 1743d040b1 ("ARM: keystone: Enable DM_I2C by default")
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
CS Systemes d'Information (CSSI) manufactures two boards, named MCR3000
and CMPC885 which are respectively based on MPC866 and MPC885 processors.
This patch adds support for the first board.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
For processors whose core runs at twice the bus frequency,
the fallback frequency calculation in Linux provides a wrong
result. Therefore, U-boot needs to pass the correct value.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
immap.c used to be common to several CPUs. It is now
only linked to the 8xx, so this patch moves it into
arch/powerpc/cpu/mpc8xx/
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Reviewed-by: Heiko Schocher <hs@denx.de>
CS Systemes d'Information (CSSI) manufactures 8xx boards for
critical communication systems. Those boards have been
running U-Boot since 2010 and will have to be maintained
until at least 2027.
commit 5b8e76c35e
("powerpc, 8xx: remove support for 8xx") orphaned those boards
by removing support for the mpc8xx CPU.
This commit partially restores support for the 8xx, with the
following limitations:
- Restores support for MPC866 and MPC885 only
- Does not restore IDE, PCMCIA, I2C, USB
- Does not restore examples
- Does not restore POST
- Does not restore Ethernet on SCC
- Does not restore console on SCC
- Does not restore bedbug and kgdb support
As the 866 and 885 do not support the following features,
they are not restored either:
- VIDEO / LCD
- RTC clock
The CPM uCODE patch is not restored either, because:
- 866 and 885 already have support for I2C and SPI relocation
without a uCODE patch
- relocation of SMC, I2C or SPI is only needed for using SCCs
for Ethernet or QMC
The dynamic setup/calculation of clocks is removed, we
expect the target being use with the clock and PLPRCR register
defined in the configuration.
All the clock settings for 8xx prior to 866 is removed as
well as we now only support 866 and 885.
This code is mature and addresses mature boards. Therefore
all code enclosed in '#if 0/#endif' and '#if XX_DEBUG/#endif'
is unneeded.
The following files are not restored by this patch:
- arch/powerpc/cpu/mpc8xx/bedbug_860.c
- arch/powerpc/cpu/mpc8xx/fec.h
- arch/powerpc/cpu/mpc8xx/kgdb.S
- arch/powerpc/cpu/mpc8xx/plprcr_write.S
- arch/powerpc/cpu/mpc8xx/scc.c
- arch/powerpc/cpu/mpc8xx/upatch.c
- arch/powerpc/cpu/mpc8xx/video.c
- arch/powerpc/include/asm/status_led.h
- arch/powerpc/lib/ide.c
- arch/powerpc/lib/ide.h
- doc/README.MPC866
- drivers/pcmcia/mpc8xx_pcmcia.c
- drivers/rtc/mpc8xx.c
- drivers/usb/gadget/mpc8xx_udc.c
- drivers/video/mpc8xx_lcd.c
- examples/standalone/test_burst.c
- examples/standalone/test_burst.h
- examples/standalone/test_burst_lib.S
- examples/standalone/timer.c
- include/mpc823_lcd.h
- include/usb/mpc8xx_udc.h
- post/cpu/mpc8xx/Makefile
- post/cpu/mpc8xx/cache.c
- post/cpu/mpc8xx/cache_8xx.S
- post/cpu/mpc8xx/ether.c
- post/cpu/mpc8xx/spr.c
- post/cpu/mpc8xx/uart.c
- post/cpu/mpc8xx/usb.c
- post/cpu/mpc8xx/watchdog.c
Some of the restored files are not located in a proper location.
In order to keep traceability of the changes, they will be
moved to their correct location and moved to Kconfig in a
followup patch.
This patch also declares CSSI as point of contact for the update
of the 8xx platform, as those boards are the only ones still
being maintained on the 8xx area. A later patch will add
those boards to the tree.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
AVR32 is gone. It's already more than two years for no support in Buildroot,
even longer there is no support in GCC (last version is heavily patched 4.2.4).
Linux kernel v4.12 got rid of it (and v4.11 didn't build successfully).
There is no good point to keep this support in U-Boot either.
Reviewed-by: Simon Glass <sjg@chromium.org>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Heiko Schocher <hs@denx.de>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
The current code gives a warning:
arch/arm/mach-stm32/stm32f7/soc.c: In function 'arch_cpu_init':
arch/arm/mach-stm32/stm32f7/soc.c:38:2: error: 'for' loop initial
declarations are only allowed in C99 or C11 mode
for (int i = 0; i < ARRAY_SIZE(stm32_region_config); i++)
^
arch/arm/mach-stm32/stm32f7/soc.c:38:2: note: use option -std=c99,
-std=gnu99, -std=c11 or -std=gnu11 to compile your code
Fix it by moving the declaration to the top of the function.
Signed-off-by: Simon Glass <sjg@chromium.org>
Series-cc trini
This actually works on snapdragon.. not sure why we weren't using it.
Fixes reboot/poweroff when using UEFI.
Signed-off-by: Rob Clark <robdclark@gmail.com>
Reviewed-by: Alexander Graf <agraf@suse.de>
There was for long time no activity in the 4xx area.
We need to go further and convert to Kconfig, but it
turned out, nobody is interested anymore in 4xx,
so remove it.
Signed-off-by: Heiko Schocher <hs@denx.de>
The author of the commit discovered later on that this was already being
done in cleanup_before_linux() on arch/arm/cpu/armv7m/cpu.c.
This reverts commit 8f079cccb3.
Signed-off-by: Tom Rini <trini@konsulko.com>
ARC HS Development Kit board is a new low-cost
development platform sporting ARC HS38 in real silicon
with nice set of features such as:
* Quad-core ARC HS38 with 512 kB L2 cache and running @1GHz
* 4Gb of DDR (we use only lowest 1Gb out of it now)
* Lots of DesigWare peripherals
* Different connectivity modules:
- Synopsys HAPS HT3
- Arduino-compatible connector
- MikroBUS
This initial commit supports the following peripherals:
* UART (DW 8250)
* Ethernet (DW GMAC)
* SD/MMC (DW Mobile Storage)
* USB 1.1 & 2.0
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
We used to use the same memory layout and size for a couple of
boards and thus we just hardcoding IOC aperture start and size.
Now when we're getting more boards with more memory on board we
need to have an ability to set IOC so it matches real DDR layout
and size.
Even though it is not really a must but for simplicity we assume
IOC covers all the DDR we have, that gives us a chance to not
bother where DMA buffers are allocated - any part of DDR is OK.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
ARCompact cores are not supposed to be used in SMP designs
(this doesn't stop people from creation of heterogeneous chips,
for an example keep reading) so there's no point in
checking ARCNUM and halting somebody if we build for ARC700.
Moreover on AXS101 board we have ARC770 in the ASIC together with
other ARC cores and ARC770 happens to be the last node in JTAG chain
with ARCNUM = 4. And existing check halts the one and only core we
want keep running.
Signed-off-by: Alexey Brodkin <abrodkin@synopsys.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
taurus board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
since commit: f8b7fff1d5 "serial: atmel_usart: Add clk support"
smartweb board comes not up anymore. Fix it.
Signed-off-by: Heiko Schocher <hs@denx.de>
Acked-by: Wenyou Yang <wenyou.yang@microchip.com>
The origin SPL_USE_ARCH_MEMSET/MEMCPY use same prompt message
as USE_ARCH_MEMSET/MEMCPY, which makes it's hard to distinguish
them in menuconfig interface. This patch gives them different
prompt messages for spl and none-spl config.
Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
The ti816x SoC revision of the ethernet IP block is handled by the
"davinci_emac" driver, rather than the "cpsw" driver as done by later
members of the family. Enable the relevant plumbing.
Signed-off-by: Sriramakrishnan <srk@ti.com>
Signed-off-by: Vitaly Wool <vitaly.wool@konsulko.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
This reverts commit ddb3ac3c71.
With MMC converted to driver model, SCSI driver is broken due to
zero address access at (ops->read) in block_dread() function.
The fix (SCSI driver converted to DM) is ready in u-boot-dm branch,
but it is too late for this relese to get that in.
Signed-off-by: Bin Meng <bmeng.cn@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>
Add initial device tree support for LD20 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Add initial device tree support for LD11 Global board.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Fix warnings reported by sparse:
- ... was not declared. Should it be static?"
- cast to restricted __be32
While fixing those, the type conflict of cci500_init() was found.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Now that we can specify DT nodes that can be used in spl, mark
all necessary nodes as u-boot,dm-spl.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Now that we can specify DT nodes that can be used in spl, mark
all necessary nodes as u-boot,dm-spl.
Signed-off-by: Lokesh Vutla <lokeshvutla@ti.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
It has been observed that between PG1.0 and PG2.0/2.1 depending on
which device we boot from, we may see a different value here than is
documented in the TRM. Update the values for NAND and MMC1 based on
real life usage on each revision.
Signed-off-by: Tom Rini <trini@konsulko.com>
